"qcom,dsi-host-index" and "qcom,dsi-phy-index" DT props aren't
acceptable and have never been used in any DT files. Remove them.

Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

DSI6G v2.0+ blocks have a new clock input to them called
byte_intf_clk. It's rate is to be set as byte_clk / 2.

Within the clock controller (CC) subsystem, this clock is a
child/descendant of the byte_clk.

Set it up as an optional clock in the DSI host driver. Make sure
that we enable/set its rate only after we configure byte_clk.
This is required for the ancestor clocks in the CC to be
configured correctly.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

SDM845 contains 2 DSI6G v2.2.1 host controllers. Add them in dsi_cfg.

Cc: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

We try to get the interface clock in dsi_get_config early during DSI's
component bind. Try getting both the "iface" and "iface_clk" clock name
variants so that we are compatible with both new and legacy DT.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

Populate the PHY ops with the downstream driver as reference.

There are a couple of TODOs which need to be resolved:
- The PHY timings are all hardcoded for now. This needs to be replaced
  with automatic calculations once we get/understand them.
- There are some lane configuration registers which use a new
  representation between physical and logical lane mappings. For now,
  we've hardcoced them to follow the default mapping (i.e
  logical 0 -> phy 0, logical 1 -> phy 1 etc).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

Populate PLL clock ops from downstream. This contains the VCO PLL
ops and the registration of standard clk_divider and clk_mux clocks.
Unlike 14nm PLL, the postdividers/mux of the slave PLL doesn't need
to be set to the same values of the postdivs/mux of the master PLL.
Hence, we don't need special postdivider clock ops like we did with
the 14nm PLL driver.

Like the previous PLL drivers, the implementation is slightly different
from downstream. We don't use shadow clocks, but have the ability to
reparent the RCGs to a different source.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

Add new 10nm DSI PLL/PHY files that will be used on SDM845.

Just populate empty pll/phy funcs for now. These will be filled up
later.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

This flags cause cmdstream to be executed from the ringbuffer (RB)
instead of IB1.  Normally not something you'd ever want to do, but
it is super useful for firmware debugging.

Hidden behind CAP_SYS_RAWIO and a default=n kconfig option which
depends on EXPERT (and has a suitably scary warning), to prevent
it from being used on accident.
Signed-off-by: Rob Clark <robdclark@gmail.com>

Add some debugfs to dump out PFP and ME microcontroller state, as well
as some of the queues (MEQ and ROQ).  Also add a debugfs file to trigger
a GPU reset (and reloading the firmware on next submit).
Signed-off-by: Rob Clark <robdclark@gmail.com>

Move null checks of pointer arguments to the beginning of the
modeset init function since they are referenced immediately
instead of after they have already been used.
Signed-off-by: Lloyd Atkinson <latkinso@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

Check DSI instance id argument against the proper boundary size
to protect against invalid configuration of the DSI id.
Signed-off-by: Lloyd Atkinson <latkinso@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

Make msm_dsi_pll_init consistently return an error code instead
of NULL when pll initialization fails so that later pll
retrieval can check against an error code. Add checks for these
failures after retrieval of src_pll to avoid invalid pointer
dereferences later in msm_dsi_pll_get_clk_provider.
Signed-off-by: Lloyd Atkinson <latkinso@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

Add HDCP support to i915 drm driver.

* tag 'topic/hdcp-2018-02-13' of git://anongit.freedesktop.org/drm/drm-misc: (26 commits)
  drm/i915: fix misalignment in HDCP register def
  drm/i915: Reauthenticate HDCP on failure
  drm/i915: Detect panel's hdcp capability
  drm/i915: Optimize HDCP key load
  drm/i915: Retry HDCP bksv read
  drm/i915: Connector info in HDCP debug msgs
  drm/i915: Stop encryption for repeater with no sink
  drm/i915: Handle failure from 2nd stage HDCP auth
  drm/i915: Downgrade hdcp logs from INFO to DEBUG_KMS
  drm/i915: Restore HDCP DRM_INFO when with no downstream
  drm/i915: Check for downstream topology errors
  drm/i915: Start repeater auth on READY/CP_IRQ
  drm/i915: II stage HDCP auth for repeater only
  drm/i915: Extending HDCP for HSW, BDW and BXT+
  drm/i915/dp: Fix compilation of intel_dp_hdcp_check_link
  drm/i915: Only disable HDCP when it's active
  drm/i915: Don't allow HDCP on PORT E/F
  drm/i915: Implement HDCP for DisplayPort
  drm/i915: Implement HDCP for HDMI
  drm/i915: Add function to output Aksv over GMBUS
  ...

drm-misc-next for 4.17:

UAPI Changes:
- drm/vc4: Expose performance counters to userspace (Boris)

Cross-subsystem Changes:
- MAINTAINERS: Linus to maintain panel-arm-versatile in -misc (Linus)

Core Changes:
- Only use swiotlb when necessary (Chunming)

Driver Changes:
- drm/panel: Add support for ARM Versatile panels (Linus)
- pl111: Improvements around versatile panel support (Linus)

----------------------------------------
Tagged on 2018-02-06:
drm-misc-next for 4.17:

UAPI Changes:
- Validate mode flags + type (Ville)
- Deprecate unused mode flags PIXMUX, BCAST (Ville)
- Deprecate unused mode types BUILTIN, CRTC_C, CLOCK_C, DEFAULT (Ville)

Cross-subsystem Changes:
- MAINTAINERS: s/Daniel/Maarten/ for drm-misc (Daniel)

Core Changes:
- gem: Export gem functions for drivers to use (Samuel)
- bridge: Introduce bridge timings in drm_bridge (Linus)
- dma-buf: Allow exclusive fence to be bundled in fence array when
	   calling reservation_object_get_fences_rcu (Christian)
- dp: Add training pattern 4 and HBR3 support to dp helpers (Manasi)
- fourcc: Add alpha bit to formats to avoid driver format LUTs (Maxime)
- mode: Various cleanups + add new device-wide .mode_valid hook (Ville)
- atomic: Fix state leak when non-blocking commits fail (Leo)
	  NOTE: IIRC, this was cross-picked to -fixes so it might fall out
- crc: Allow polling on the data fd (Maarten)

Driver Changes:
- bridge/vga-dac: Add THS8134* support (Linus)
- tinydrm: Various MIPI DBI improvements/cleanups (Noralf)
- bridge/dw-mipi-dsi: Cleanups + use create_packet helper (Brian)
- drm/sun4i: Add Display Engine frontend support (Maxime)
- drm/sun4i: Add zpos support + increase num planes from 2 to 4 (Maxime)
- various: Use drm_mode_get_hv_timing() to fill plane clip rectangle (Ville)
- stm: Add 8-bit clut support, add dsi phy v1.31 support, +fixes (Phillipe)

Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Chunming Zhou <david1.zhou@amd.com>
Cc: Samuel Li <Samuel.Li@amd.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Brian Norris <briannorris@chromium.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

* tag 'drm-misc-next-2018-02-13' of git://anongit.freedesktop.org/drm/drm-misc: (115 commits)
  drm/radeon: only enable swiotlb path when need v2
  drm/amdgpu: only enable swiotlb alloc when need v2
  drm: add func to get max iomem address v2
  drm/vc4: Expose performance counters to userspace
  drm: Print the pid when debug logging an ioctl error.
  drm/stm: ltdc: remove non-alpha color formats on layer 2 for older hw
  drm/stm: ltdc: add non-alpha color formats
  drm/bridge/synopsys: dsi: Add 1.31 version support
  drm/bridge/synopsys: dsi: Add read feature
  drm/pl111: Support multiple endpoints on the CLCD
  drm/pl111: Support variants with broken VBLANK
  drm/pl111: Support variants with broken clock divider
  drm/pl111: Handle the Versatile RGB/BGR565 mode
  drm/pl111: Properly detect the ARM PL110 variants
  drm/panel: Add support for ARM Versatile panels
  drm/panel: Device tree bindings for ARM Versatile panels
  drm/bridge: Rename argument from crtc to bridge
  drm/crc: Add support for polling on the data fd.
  drm/sun4i: Use drm_mode_get_hv_timing() to populate plane clip rectangle
  drm/rcar-du: Use drm_mode_get_hv_timing() to populate plane clip rectangle
  ...

UAPI Changes:

- Userspace whitelist register GEN9_SLICE_COMMON_ECO_CHICKEN1 for GLK (Kenneth)
- Non-existent PMU counters are not placed to sysfs (Tvrtko)
- Add a note to deprecate I915_SET_COLORKEY_NONE and ignore it (Ville)
	* Intel DDX never ended using it, and implementation was wonky

Core Changes:

- Moved away from struct timeval into ktime_t in prep for 2038 (Arnd)
	* Merged the i915 portion through drm-tip, no core dependencies

Driver Changes:

- Base support for Icelake and Icelake PCH (Anusha, Rodrigo, Mahesh, Paulo, James, Kelvin)
- Add AUX-F port support for Cannonlake (Rodrigo)
- New DMC firmware for 1.07 Cannonlake (Anusha)
	* Go to linux-firmware.git to get it
- Reject non-cursor planes nearly (3 px) out of screen on GLK/CNL (Imre)
- Y/Yf modifiers restored for SKL+ sprites (Ville)
- Compressed framebuffer support for sprites (Ville)
- Tune down overly aggressive shrinking (Chris)
- Shrink kmem caches when GPU is idle (Chris)
- EDID bit-banging fallback for HDMI EDID (Stefan)
- Don't boost the GPU when the waited request is already running (Chris)
- Avoid GLK/BXT CDCLK frequency locking timeouts (Imre)
- Limit DP link rate according to VBT on CNL+ (Jani)
- Skip post-reset request emission if the engine is not idle (Chris)
- Report any link training error on a fixed eDP panel as errors (Manasi)
- DSI panel fixes for Bay Trail (Hans)
- Selftest additions and improvements (Chris, Matt)
- DMA fence test additions and accompanying fixes (Chris)
- Power domain vs. register access fix (Maarten)
- Squelch warnings for people with teensy framebuffers (stride < 512) (Maarten)
- Increase Render/Media power gating hysteresis for Gen9+ (Chris)
- HDMI vswing display workaround for Gen9+ (Ville)
- GuC code cleanup and lockdep fixes (Sagar, Michal Wa.)
- Continuously run hangcheck for simplicity (Chris)
- Execlist debugging improvements (Chris)
- GuC debugging improvements (Sujaritha, Michal Wa., Sagar)
- Command parser boundary checks (Michal Srb)
- Add a workaround for 3DSTATE_SAMPLE_PATTERN on CNL (Rafael)
- Fix PMU enabling race condition (Tvrtko)
- Usual smaller testing and debugging improvements

* tag 'drm-intel-next-2018-02-07' of git://anongit.freedesktop.org/drm/drm-intel: (158 commits)
  drm/i915: Update DRIVER_DATE to 20180207
  drm/i915/pmu: Fix PMU enable vs execlists tasklet race
  drm/i915/cnl: WaPipeControlBefore3DStateSamplePattern
  drm/i915/cmdparser: Do not check past the cmd length.
  drm/i915/cmdparser: Check reg_table_count before derefencing.
  drm/i915: Deprecate I915_SET_COLORKEY_NONE
  drm/i915: Skip post-reset request emission if the engine is not idle
  drm/i915/execlists: Move the reset bits to a more natural home
  drm/i915/selftests: Use a sacrificial context for hang testing
  drm/i915/selftests: Flush old resets between engines
  drm/i915/breadcrumbs: Drop request reference for the signaler thread
  drm/i915: Remove unbannable context spam from reset
  drm/i915/execlists: Remove the startup spam
  drm/i915: Show the GPU state when declaring wedged
  drm/i915: Always update the no_fbc_reason when disabling
  drm/i915: Add some newlines to intel_engine_dump() headers
  drm/i915: Report if an unbannable context is involved in a GPU hang
  drm/i915: Remove spurious DRM_ERROR for cancelled interrupts
  drm/i915/execlists: Flush GTIIR on clearing CS interrupts during reset
  drm/i915: reduce indent in pch detection
  ...

swiotlb expands our card accessing range, but its path always is slower
than ttm pool allocation.
So add condition to use it.
v2: move a bit later
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Monk Liu <monk.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180209024410.1469-3-david1.zhou@amd.com

get the max io mapping address of system memory to see if it is over
our card accessing range.
v2: move checking later
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Monk Liu <monk.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180209024410.1469-2-david1.zhou@amd.com

it will be used to check if the driver needs swiotlb
v2: Don't use inline, instead, move function to drm_memory.c (Michel Daenzer <michel@daenzer.net>)
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Monk Liu <monk.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180209024410.1469-1-david1.zhou@amd.com

except, again, POLLFREE and POLL_BUSY_LOOP.

With this, we finally get to the promised end result:

 - POLL{IN,OUT,...} are plain integers and *not* in __poll_t, so any
   stray instances of ->poll() still using those will be caught by
   sparse.

 - eventpoll.c and select.c warning-free wrt __poll_t

 - no more kernel-side definitions of POLL... - userland ones are
   visible through the entire kernel (and used pretty much only for
   mangle/demangle)

 - same behavior as after the first series (i.e. sparc et.al. epoll(2)
   working correctly).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:

    for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
        L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
        for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
    done

with de-mangling cleanups yet to come.

NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do.  But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.

The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull more poll annotation updates from Al Viro:
 "This is preparation to solving the problems you've mentioned in the
  original poll series.

  After this series, the kernel is ready for running

      for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
            L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
            for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
      done

  as a for bulk search-and-replace.

  After that, the kernel is ready to apply the patch to unify
  {de,}mangle_poll(), and then get rid of kernel-side POLL... uses
  entirely, and we should be all done with that stuff.

  Basically, that's what you suggested wrt KPOLL..., except that we can
  use EPOLL... instead - they already are arch-independent (and equal to
  what is currently kernel-side POLL...).

  After the preparations (in this series) switch to returning EPOLL...
  from ->poll() instances is completely mechanical and kernel-side
  POLL... can go away. The last step (killing kernel-side POLL... and
  unifying {de,}mangle_poll() has to be done after the
  search-and-replace job, since we need userland-side POLL... for
  unified {de,}mangle_poll(), thus the cherry-pick at the last step.

  After that we will have:

   - POLL{IN,OUT,...} *not* in __poll_t, so any stray instances of
     ->poll() still using those will be caught by sparse.

   - eventpoll.c and select.c warning-free wrt __poll_t

   - no more kernel-side definitions of POLL... - userland ones are
     visible through the entire kernel (and used pretty much only for
     mangle/demangle)

   - same behavior as after the first series (i.e. sparc et.al. epoll(2)
     working correctly)"

* 'work.poll2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  annotate ep_scan_ready_list()
  ep_send_events_proc(): return result via esed->res
  preparation to switching ->poll() to returning EPOLL...
  add EPOLLNVAL, annotate EPOLL... and event_poll->event
  use linux/poll.h instead of asm/poll.h
  xen: fix poll misannotation
  smc: missing poll annotations

Pull xtense fix from Max Filippov:
 "Build fix for xtensa architecture with KASAN enabled"

* tag 'xtensa-20180211' of git://github.com/jcmvbkbc/linux-xtensa:
  xtensa: fix build with KASAN

Pull nios2 update from Ley Foon Tan:

 - clean up old Kconfig options from defconfig

 - remove leading 0x and 0s from bindings notation in dts files

* tag 'nios2-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2:
  nios2: defconfig: Cleanup from old Kconfig options
  nios2: dts: Remove leading 0x and 0s from bindings notation

The commit 917538e2 ("kasan: clean up KASAN_SHADOW_SCALE_SHIFT
usage") removed KASAN_SHADOW_SCALE_SHIFT definition from
include/linux/kasan.h and added it to architecture-specific headers,
except for xtensa. This broke the xtensa build with KASAN enabled.
Define KASAN_SHADOW_SCALE_SHIFT in arch/xtensa/include/asm/kasan.h

Reported by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 917538e2 ("kasan: clean up KASAN_SHADOW_SCALE_SHIFT usage")
Acked-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>

Remove old, dead Kconfig option INET_LRO. It is gone since
commit 7bbf3cae ("ipv4: Remove inet_lro library").
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Ley Foon Tan <ley.foon.tan@intel.com>

Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:

Warning (unit_address_format): Node /XXX unit name should not have leading "0x"

and

Warning (unit_address_format): Node /XXX unit name should not have leading 0s

Converted using the following command:

find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -E -i -e "s/@0x([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" -e "s/@0+([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" {} +

For simplicity, two sed expressions were used to solve each warnings separately.

To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:

https://elinux.org/Device_Tree_Linux#Linux_conventions

This is a follow up to commit 4c9847b7 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Ley Foon Tan <ley.foon.tan@intel.com>

The V3D engine has various hardware counters which might be interesting
to userspace performance analysis tools.

Expose new ioctls to create/destroy a performance monitor object and
query the counter values of this perfmance monitor.

Note that a perfomance monitor is given an ID that is only valid on the
file descriptor it has been allocated from. A performance monitor can be
attached to a CL submission and the driver will enable HW counters for
this request and update the performance monitor values at the end of the
job.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20180112090926.12538-1-boris.brezillon@free-electrons.com

When we debug print what ioctl we're calling into, we include the pid.
If you have multiple processes rendering simulataneously, the error
return also needs the pid so you can see which of the ioctl calls was
the one to fail.
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130215643.11016-1-eric@anholt.netReviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Pull PCI fix from Bjorn Helgaas:
 "Fix a POWER9/powernv INTx regression from the merge window (Alexey
  Kardashevskiy)"

* tag 'pci-v4.16-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  powerpc/pci: Fix broken INTx configuration via OF

Pull block fixes from Jens Axboe:
 "A few fixes to round off the merge window on the block side:

   - a set of bcache fixes by way of Michael Lyle, from the usual bcache
     suspects.

   - add a simple-to-hook-into function for bpf EIO error injection.

   - fix blk-wbt that mischarectized flushes as reads. Improve the logic
     so that flushes and writes are accounted as writes, and only reads
     as reads. From me.

   - fix requeue crash in BFQ, from Paolo"

* tag 'for-linus-20180210' of git://git.kernel.dk/linux-block:
  block, bfq: add requeue-request hook
  bcache: fix for data collapse after re-attaching an attached device
  bcache: return attach error when no cache set exist
  bcache: set writeback_rate_update_seconds in range [1, 60] seconds
  bcache: fix for allocator and register thread race
  bcache: set error_limit correctly
  bcache: properly set task state in bch_writeback_thread()
  bcache: fix high CPU occupancy during journal
  bcache: add journal statistic
  block: Add should_fail_bio() for bpf error injection
  blk-wbt: account flush requests correctly

Pull x86 platform driver updates from Darren Hart:
 "Mellanox fixes and new system type support.

  Mostly data for new system types with a correction and an
  uninitialized variable fix"

[ Pulling from github because git.infradead.org currently seems to be
  down for some reason, but Darren had a backup location    - Linus ]

* tag 'platform-drivers-x86-v4.16-3' of git://github.com/dvhart/linux-pdx86:
  platform/x86: mlx-platform: Add support for new 200G IB and Ethernet systems
  platform/x86: mlx-platform: Add support for new msn201x system type
  platform/x86: mlx-platform: Add support for new msn274x system type
  platform/x86: mlx-platform: Fix power cable setting for msn21xx family
  platform/x86: mlx-platform: Add define for the negative bus
  platform/x86: mlx-platform: Use defines for bus assignment
  platform/mellanox: mlxreg-hotplug: Fix uninitialized variable

Merge tag 'chrome-platform-for-linus-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform

Pull chrome platform updates from Benson Leung:

 - move cros_ec_dev to drivers/mfd

 - other small maintenance fixes

[ The cros_ec_dev movement came in earlier through the MFD tree  - Linus ]

* tag 'chrome-platform-for-linus-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform:
  platform/chrome: Use proper protocol transfer function
  platform/chrome: cros_ec_lpc: Add support for Google Glimmer
  platform/chrome: cros_ec_lpc: Register the driver if ACPI entry is missing.
  platform/chrome: cros_ec_lpc: remove redundant pointer request
  cros_ec: fix nul-termination for firmware build info
  platform/chrome: chromeos_laptop: make chromeos_laptop const

Pull KVM updates from Radim Krčmář:
 "ARM:

   - icache invalidation optimizations, improving VM startup time

   - support for forwarded level-triggered interrupts, improving
     performance for timers and passthrough platform devices

   - a small fix for power-management notifiers, and some cosmetic
     changes

  PPC:

   - add MMIO emulation for vector loads and stores

   - allow HPT guests to run on a radix host on POWER9 v2.2 CPUs without
     requiring the complex thread synchronization of older CPU versions

   - improve the handling of escalation interrupts with the XIVE
     interrupt controller

   - support decrement register migration

   - various cleanups and bugfixes.

  s390:

   - Cornelia Huck passed maintainership to Janosch Frank

   - exitless interrupts for emulated devices

   - cleanup of cpuflag handling

   - kvm_stat counter improvements

   - VSIE improvements

   - mm cleanup

  x86:

   - hypervisor part of SEV

   - UMIP, RDPID, and MSR_SMI_COUNT emulation

   - paravirtualized TLB shootdown using the new KVM_VCPU_PREEMPTED bit

   - allow guests to see TOPOEXT, GFNI, VAES, VPCLMULQDQ, and more
     AVX512 features

   - show vcpu id in its anonymous inode name

   - many fixes and cleanups

   - per-VCPU MSR bitmaps (already merged through x86/pti branch)

   - stable KVM clock when nesting on Hyper-V (merged through
     x86/hyperv)"

* tag 'kvm-4.16-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (197 commits)
  KVM: PPC: Book3S: Add MMIO emulation for VMX instructions
  KVM: PPC: Book3S HV: Branch inside feature section
  KVM: PPC: Book3S HV: Make HPT resizing work on POWER9
  KVM: PPC: Book3S HV: Fix handling of secondary HPTEG in HPT resizing code
  KVM: PPC: Book3S PR: Fix broken select due to misspelling
  KVM: x86: don't forget vcpu_put() in kvm_arch_vcpu_ioctl_set_sregs()
  KVM: PPC: Book3S PR: Fix svcpu copying with preemption enabled
  KVM: PPC: Book3S HV: Drop locks before reading guest memory
  kvm: x86: remove efer_reload entry in kvm_vcpu_stat
  KVM: x86: AMD Processor Topology Information
  x86/kvm/vmx: do not use vm-exit instruction length for fast MMIO when running nested
  kvm: embed vcpu id to dentry of vcpu anon inode
  kvm: Map PFN-type memory regions as writable (if possible)
  x86/kvm: Make it compile on 32bit and with HYPYERVISOR_GUEST=n
  KVM: arm/arm64: Fixup userspace irqchip static key optimization
  KVM: arm/arm64: Fix userspace_irqchip_in_use counting
  KVM: arm/arm64: Fix incorrect timer_is_pending logic
  MAINTAINERS: update KVM/s390 maintainers
  MAINTAINERS: add Halil as additional vfio-ccw maintainer
  MAINTAINERS: add David as a reviewer for KVM/s390
  ...

59f47eff ("powerpc/pci: Use of_irq_parse_and_map_pci() helper")
replaced of_irq_parse_pci() + irq_create_of_mapping() with
of_irq_parse_and_map_pci(), but neglected to capture the virq
returned by irq_create_of_mapping(), so virq remained zero, which
caused INTx configuration to fail.

Save the virq value returned by of_irq_parse_and_map_pci() and correct
the virq declaration to match the of_irq_parse_and_map_pci() signature.

Fixes: 59f47eff "powerpc/pci: Use of_irq_parse_and_map_pci() helper"
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Pull more Kbuild updates from Masahiro Yamada:
 "Makefile changes:
   - enable unused-variable warning that was wrongly disabled for clang

  Kconfig changes:
   - warn about blank 'help' and fix existing instances
   - fix 'choice' behavior to not write out invisible symbols
   - fix misc weirdness

  Coccinell changes:
   - fix false positive of free after managed memory alloc detection
   - improve performance of NULL dereference detection"

* tag 'kbuild-v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (21 commits)
  kconfig: remove const qualifier from sym_expand_string_value()
  kconfig: add xrealloc() helper
  kconfig: send error messages to stderr
  kconfig: echo stdin to stdout if either is redirected
  kconfig: remove check_stdin()
  kconfig: remove 'config*' pattern from .gitignnore
  kconfig: show '?' prompt even if no help text is available
  kconfig: do not write choice values when their dependency becomes n
  coccinelle: deref_null: avoid useless computation
  coccinelle: devm_free: reduce false positives
  kbuild: clang: disable unused variable warnings only when constant
  kconfig: Warn if help text is blank
  nios2: kconfig: Remove blank help text
  arm: vt8500: kconfig: Remove blank help text
  MIPS: kconfig: Remove blank help text
  MIPS: BCM63XX: kconfig: Remove blank help text
  lib/Kconfig.debug: Remove blank help text
  Staging: rtl8192e: kconfig: Remove blank help text
  Staging: rtl8192u: kconfig: Remove blank help text
  mmc: kconfig: Remove blank help text
  ...

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull misc vfs fixes from Al Viro.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  seq_file: fix incomplete reset on read from zero offset
  kernfs: fix regression in kernfs_fop_write caused by wrong type

This function returns realloc'ed memory, so the returned pointer
must be passed to free() when done.  So, 'const' qualifier is odd.
It is allowed to modify the expanded string.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>