Commit(def56bba input: snvs_pwrkey: use "wakeup-source"
as deivce tree property name) replaces the property name
of "wakeup" with "wakeup-source", update this change
in i.MX6SX dtsi accordingly.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The ADC clock frequency is limited depending on modes used. Add
device tree property which allow to set the mode used and the
maximum frequency ratings for the instance. These allows to
set the ADC clock to a frequency which is within specification
according to the actual mode used.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Change SNVS rtc to syscon interface.
Enable onoff key and power off function.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add ethernet fec1 and fec2 support for i.MX6ul 14x14 evk board.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

SOC i.MX6UL has two ethernet MACs, add fec1 and fec2 support for i.MX6UL.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support of internal rtc on imx27.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Define Vybrid's UART0, connected to the Colibri pinout UART_A, as
standard output.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This enables the available eTSEC ethernet ports for the
ls1021aqds and ls1021atwr boards.
For the QDS, SGMII connections (via riser cards) are assumed
for the eTSEC0 and eTSEC1 ports as default configuration.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add basic support for all the eTSEC controllers on the
ls1021a SoC.  Second interrupt group register blocks
and their corresponding Rx/Tx/Err interrupt sources are
included as well for each eTSEC node.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

enable qspi support
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

some pin name should be capital "_B" instead of "_b"
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Enable usb host and function driver
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This commit adds io-channel-cells property to the ADC node. This
property is required in order for an IIO consumer driver to work.
Especially required for Colibri VF50, as the touchscreen driver
uses ADC channels with the ADC driver based on IIO framework.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch adds dts nodes for audio on LS1021A.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add USBOTG and USB host 1 support
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

snvs is MFP device. Change dts to use syscon to allocate register resource.
snvs power off also switch to common syscon-poweroff
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add new SOC i.MX6UL dtb file support, including evk board
support

i.MX6 Ultralite processor include one ARM cortext-A7 core.
Offer high perfomance and lowest power consumption.

Main included:
- 4 MMC/SD/SDIO
- 2 USB 2.0 OTG
- 3 I2S/SAI/AC97
- 4 eCSPI
- 4 I2C
- 2 ENET
- 2 CAN
- 3 wdog
- ASRC
- 8 uart
- LCDIF
- PXP
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Fancy Fang <chen.fang@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

add pin mux define file
Signed-off-by: Bai Ping <b51503@freescale.com>
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This part just add necessary change to boot imx6ul.
Update clock and pinctrl for imx6ul
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Extend the existing Vybrid eSDHC devicetree implementation to also
describe the esdhc0 functional block.

Tested on a custom VF610-based board with a Toshiba THGBM1G5D2EBAI7 eMMC
module attached to esdhc0.
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Currently it is not possible to have HDMI and LVDS working simultaneously,
because both ports try to use PLL5.

Move the LVDS clock parent to PLL3_USB_OTG, so that HDMI and LVDS can be
driven from independent sources.

With this change the LDB pixel clock goes to 68.57 MHz, which is still
within the valid range for the HSD100PXN1 LVDS panel.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This commit extends the existing Vybrid QSPI devicetree implementation
to also describe the qspi1 functional block.
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Both 'reg' and 'reg-names' are required properties according to binding
documentation, and both should contain two items.
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Freescale DSPI driver has been updated and supports TCF interrupt type now.
In the new driver we choose the interrupt type according the compatible
string of the device node.
This patch update the compatible string of DSPI device node of LS1021A in
order to use the correct interrupt type.
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Added etm, etb, funnel and replicator

usage example:

    echo 1 >/sys/bus/coresight/devices/30086000.etr/enable_sink
    echo 1 >/sys/bus/coresight/devices/3007c000.etm/enable_source

        coresight-tmc 30086000.etr: TMC enabled
        coresight-replicator replicator.1: REPLICATOR enabled
        coresight-tmc 30084000.tmc: TMC enabled
        coresight-funnel 30083000.funnel: FUNNEL inport 0 enabled
        coresight-funnel 30041000.funnel: FUNNEL inport 0 enabled
        coresight-etm3x 3007c000.etm: ETM tracing enabled

    etm enable here.
    trace data save at /dev/30086000.etr

    cat /dev/30086000.etr > trace.data

        coresight-tmc 30086000.etr: TMC read start
        coresight-tmc 30086000.etr: TMC read end

    use ptm2human(https://github.com/hwangcc23/ptm2human) to show trace data

    ptm2human -i trace.data
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Currently it is not possible to have HDMI and LVDS working simultaneously,
because both ports try to use PLL5.

Move the LVDS clock parent to PLL3_USB_OTG, so that HDMI and LVDS can be
driven from independent sources.

With this change the LDB pixel clock goes to 68.57 MHz, which is still
within the valid range for the HSD100PXN1 LVDS panel.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Gary Bisson <gary.bisson@boundarydevices.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Currently it is not possible to have HDMI and LVDS working simultaneously,
because both ports try to use PLL5.

Move the LVDS clock parent to PLL3_USB_OTG, so that HDMI and LVDS can be
driven from independent sources.

With this change the LDB pixel clock goes to 68.57 MHz, which is still
within the valid range for the HSD100PXN1 LVDS panel.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Gary Bisson <gary.bisson@boundarydevices.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Warp board rev1.12 is the version of the hardware that will be publicly
available for the customers.

It uses UART5 as the Bluetooth serial port as well as some
additional signals for HOSTWAKE on Wifi and Bluetooth.

Make the changes to support the rev1.12 hardware.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Currently it is not possible to have HDMI and LVDS working simultaneously,
because both ports try to use PLL5.

Move the LVDS clock parent to PLL3_USB_OTG, so that HDMI and LVDS can be
driven from independent sources.

With this change the LDB pixel clock goes to 68.57 MHz, which is still
within the valid range for the HSD100PXN1 LVDS panel.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Both imx53-qsb and imx53-qsrb don't have external pull-up resistors
on the I2C1 SCL and SDA lines populated. Select open-drain mode and
enable the internal pull-up for both.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add ESAI, ASRC, CS42888 for imx6qdl-sabreauto board
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

This commit extends the existing Vybrid I2C support to cover buses i2c1,
i2c2, and i2c3.  Based in (very) large part on an initial patch by
Stefan Agner that was just lacking a couple of DMA assignments.
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add HDMI support. As the DDC I2C pins are not connected due to
pin conflicts, we do not pass the 'ddc-i2c-bus' property in
this case.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

imx6sl-warp has SD2_RESET pin connected to the eMMC reset line,
so add this pin to the usdhc2 group.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

UHS-I support is available on Ventana boards with micro-SD sockets depending
on the board revision. To support this pinctl states for 100Mhz and 200MHz
must be added as well as pinmux of the VSELECT signal. In order to support
UHS-I the I/O rail of the 4-bit data bus must be switchable between 1.8V
and 3.3V.

By adding the no-1-8-v property, which disables UHS-I support, we allow the
bootloader to be in charge of selecting which boards have this capability
by removing that property if the board model/revision implement the support.

Additionally we will remove NANDF_CS1 here from the nand pinmux group as the
second chip-select is not used on any ventana boards and this is the pad
that is used for SD3_VELECT.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Regulator stuff copied from imx6qdl-tx6.dtsi, pin configuration
taken from Boundary Devices linux kernel tree ([1] and [2]).

[1] https://github.com/boundarydevices/linux-imx6/blob/boundary-imx_3.10.17_1.0.2_ga/arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi
[2] https://github.com/boundarydevices/linux-imx6/blob/boundary-imx_3.10.17_1.0.2_ga/arch/arm/boot/dts/imx6qdl.dtsiSigned-off-by: Peter Seiderer <ps.report@gmx.net>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

enable snvs ONOFF power key support
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Enable watchdog support
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add imx6ul clock driver support.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Bai Ping <b51503@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>