This puts all of the platform_data checks in the same place, and removes
the need for a custom drv->reset() callback.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These quirks are currently set through platform_data; allow DT-based SoCs
to use them too.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The bcm63xx and bcm3384 platforms need to set OHCI_QUIRK_FRAME_NO, but
they are non-PPC platforms and don't enable CONFIG_PPC_MPC52xx.
Therefore this patch changes the code that uses OHCI_QUIRK_FRAME_NO,
making it not depend on CONFIG_PPC_MPC52xx.

Also, rephrase the comments describing OHCI_QUIRK_FRAME_NO and the
related PSW endian swap.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds an external portpower override callback, only single
port regulator control is supported now.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The current EHCI implementation is prepared to toggle the
PORT_POWER bit to enable or disable a USB-Port. In some
cases this port power can not be just toggled by the PORT_POWER
bit, and the gpio-regulator is needed to be toggled too.

This patch defines a port power control interface ehci_port_power for
ehci core use, it toggles PORT_POWER bit as well as calls platform
defined .port_power if it is defined.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

With uas over usb-3 the tags inside the uas iu-s must match the usb-3 stream
ids, and those go from 1 - qdepth.

Before blk-mq calling scsi_activate_tcq(sdev, qdepth) guaranteed that we would
only get cmnd->request->tag from 0 - (qdepth - 1), and we used those as
uas-tags / stream-ids.

With blk-mq however we are guaranteed to never get more then qdepth commands
queued at the same time, but the cmnd->request->tag values may be much larger,
which breaks uas.

This commit fixes this by generating uas tags in the 1 - qdepth range ourselves
instead of using cmnd->request->tag.

While touching all involved code anyways also rename the uas_cmd_info stream
field to uas_tag, because when using uas over usb-2 streams are not used.

Cc: Christoph Hellwig <hch@infradead.org>
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>

--
Changes in v2:
-Remove ".disable_blk_mq = true" from uas_host_template
Changes in v3:
-Rebased on top of Linus' current master branch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fixed sparse warning of
	1) incorrect type (different address spaces)
	2) incorrect type in initializer
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch modifies the usb_authorize_device() function such as that it does
not reload the device descriptor for wired devices. The reasons for this
are as follows:

* Some devices dislike the master requesting the descriptor from them twice,
  failing on the usb_get_device_descriptor() call with -ETIMEOUT. Observed this
  on my Pretec 16GB flash drive (4146:ba65).

* Malicious device could send two different descriptors - one before
  authorization, used by userspace to determine whether to authorize it and
  second to be actually used by the kernel when determining which drivers to
  bind.
Signed-off-by: Josef Gajdusek <atx@atx.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit d78c16cc ("ARM: SAMSUNG: Remove remaining legacy code")
removed the Kconfig symbol PLAT_S5P. Remove two optional dependencies on
that symbol from this Kconfig file too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

On enabling CONFIG_OF_SELFTEST which enables CONFIG_OF_DYNAMIC,
we found out that while getting PHYs for the controller we were
doing an extra of_node_put on the child node in our routines -
exynos_e/ohci_get_phy().
This child is however already put by of_get_next_available_child()
which does a of_node_put() on the "prev" node. So there's no point
in putting the same node again in our routine.
Reported-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Let's drop the warning for modems with unusual capabilities,
the associated quirk and blacklist. They made little sense.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull MTD fixes from Brian Norris:
 "Three main MTD fixes for 3.18:

   - A regression from 3.16 which was noticed in 3.17.  With the
     restructuring of the m25p80.c driver and the SPI NOR library
     framework, we omitted proper listing of the SPI device IDs.  This
     means m25p80.c wouldn't auto-load (modprobe) properly when built as
     a module.  For now, we duplicate the device IDs into both modules.

   - The OMAP / ELM modules were depending on an implicit link ordering.
     Use deferred probing so that the new link order (in 3.18-rc) can
     still allow for successful probing.

   - Fix suspend/resume support for LH28F640BF NOR flash"

* tag 'for-linus-20141102' of git://git.infradead.org/linux-mtd:
  mtd: cfi_cmdset_0001.c: fix resume for LH28F640BF chips
  mtd: omap: fix mtd devices not showing up
  mtd: m25p80,spi-nor: Fix module aliases for m25p80
  mtd: spi-nor: make spi_nor_scan() take a chip type name, not spi_device_id
  mtd: m25p80: get rid of spi_get_device_id

Pull SCSI fixes from James Bottomley:
 "This is a set of six patches consisting of:
   - two MAINTAINER updates
   - two scsi-mq fixs for the old parallel interface (not every request
     is tagged and we need to set the right flags to populate the SPI
     tag message)
   - a fix for a memory leak in scatterlist traversal caused by a
     preallocation update in 3.17
   - an ipv6 fix for cxgbi"

[ The scatterlist fix also came in separately through the block layer tree ]

* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  MAINTAINERS: ufs - remove self
  MAINTAINERS: change hpsa and cciss maintainer
  libcxgbi : support ipv6 address host_param
  scsi: set REQ_QUEUE for the blk-mq case
  Revert "block: all blk-mq requests are tagged"
  lib/scatterlist: fix memory leak with scsi-mq

Pull drm fixes from Dave Airlie:
 "Nothing too astounding or major: radeon, i915, vmwgfx, armada and
  exynos.

  Biggest ones:
   - vmwgfx has one big locking regression fix
   - i915 has come displayport fixes
   - radeon has some stability and a memory alloc failure
   - armada and exynos have some vblank fixes"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (24 commits)
  drm/exynos: correct connector->dpms field before resuming
  drm/exynos: enable vblank after DPMS on
  drm/exynos: init kms poll at the end of initialization
  drm/exynos: propagate plane initialization errors
  drm/exynos: vidi: fix build warning
  drm/exynos: remove explicit encoder/connector de-initialization
  drm/exynos: init vblank with real number of crtcs
  drm/vmwgfx: Filter out modes those cannot be supported by the current VRAM size.
  drm/vmwgfx: Fix hash key computation
  drm/vmwgfx: fix lock breakage
  drm/i915/dp: only use training pattern 3 on platforms that support it
  drm/radeon: remove some buggy dead code
  drm/i915: Ignore VBT backlight check on Macbook 2, 1
  drm/radeon: remove invalid pci id
  drm/radeon: dpm fixes for asrock systems
  radeon: clean up coding style differences in radeon_get_bios()
  drm/radeon: Use drm_malloc_ab instead of kmalloc_array
  drm/radeon/dpm: disable ulv support on SI
  drm/i915: Fix GMBUSFREQ on vlv/chv
  drm/i915: Ignore long hpds on eDP ports
  ...

Pull ARM fixes from Russell King:
 - add the new bpf syscall to ARM.
 - drop a redundant return statement in __iommu_alloc_remap()
 - fix a performance issue noticed by Thomas Petazzoni with
   kmap_atomic().
 - fix an issue with the L2 cache OF parsing code which caused it to
   incorrectly print warnings on each boot, and make the warning text
   more consistent with the rest of the code

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8180/1: mm: implement no-highmem fast path in kmap_atomic_pfn()
  ARM: 8183/1: l2c: Improve l2c310_of_parse() error message
  ARM: 8181/1: Drop extra return statement
  ARM: 8182/1: l2c: Make l2x0_cache_size_of_parse() return 'int'
  ARM: enable bpf syscall

Pull kvm fixes from Paolo Bonzini:
 "A small set of x86 fixes.  The most serious is an SRCU lockdep fix.

  A bit late - needed some time to test the SRCU fix, which only came in
  on Friday"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: vmx: defer load of APIC access page address during reset
  KVM: nVMX: Disable preemption while reading from shadow VMCS
  KVM: x86: Fix far-jump to non-canonical check
  KVM: emulator: fix execution close to the segment limit
  KVM: emulator: fix error code for __linearize

Merge branch 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes

This pull-request includes some bug fixes and code cleanups.
Especially, this fixes the bind failure issue occurred when it tries
to re-bind Exynos drm driver after unbound, and the modetest failure
issue incurred by not having a pair to vblank on and off requests.

* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
  drm/exynos: correct connector->dpms field before resuming
  drm/exynos: enable vblank after DPMS on
  drm/exynos: init kms poll at the end of initialization
  drm/exynos: propagate plane initialization errors
  drm/exynos: vidi: fix build warning
  drm/exynos: remove explicit encoder/connector de-initialization
  drm/exynos: init vblank with real number of crtcs

Pull VFS fixes from Al Viro:
 "A bunch of assorted fixes, most of them followups to overlayfs merge"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  ovl: initialize ->is_cursor
  Return short read or 0 at end of a raw device, not EIO
  isofs: don't bother with ->d_op for normal case
  isofs_cmp(): we'll never see a dentry for . or ..
  overlayfs: fix lockdep misannotation
  ovl: fix check for cursor
  overlayfs: barriers for opening upper-layer directory
  rcu: Provide counterpart to rcu_dereference() for non-RCU situations
  staging: android: logger: Fix log corruption regression

The sk_prot is irda's own set of protocol handlers, so irda should
statically know what that function is anyway, without using an indirect
pointer.  And as it happens, we know *exactly* what that pointer is
statically: it's NULL, because irda doesn't define a disconnect
operation.

So calling that function is doubly wrong, and will just cause an oops.
Reported-by: Martin Lang <mlg.hessigheim@gmail.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

During system suspend after connector switch off its dpms field
is set to connector previous dpms state. To properly resume dpms field
should be set to its actual state (off) before resuming to previous dpms state.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Before DPMS off driver disables vblank.
It should be balanced by vblank enable after DPMS on.
The patch fixes issue with page_flip ioctl not being able
to acquire vblank counter introduced by patch:
drm: Always reject drm_vblank_get() after drm_vblank_off()
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

HPD events can be generated by components even if drm_dev is not fully
initialized, to skip such events kms poll initialization should
be performed at the end of load callback followed directly by forced
connection detection.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

In case of error during plane initialization load callback
incorrectly return success, this patch fixes it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

encoder object isn't used anymore so remove it.
Signed-off-by: Inki Dae <inki.dae@samsung.com>

All KMS objects are destroyed by drm_mode_config_cleanup in proper order
so component drivers should not care about it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Initialization of vblank with MAX_CRTC caused attempts
to disabling vblanks for non-existing crtcs in case
drm used fewer crtcs. The patch fixes it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Most call paths to vmx_vcpu_reset do not hold the SRCU lock.  Defer loading
the APIC access page to the next vmentry.

This avoids the following lockdep splat:

[ INFO: suspicious RCU usage. ]
3.18.0-rc2-test2+ #70 Not tainted
-------------------------------
include/linux/kvm_host.h:474 suspicious rcu_dereference_check() usage!

other info that might help us debug this:

rcu_scheduler_active = 1, debug_locks = 0
1 lock held by qemu-system-x86/2371:
 #0:  (&vcpu->mutex){+.+...}, at: [<ffffffffa037d800>] vcpu_load+0x20/0xd0 [kvm]

stack backtrace:
CPU: 4 PID: 2371 Comm: qemu-system-x86 Not tainted 3.18.0-rc2-test2+ #70
Hardware name: Dell Inc. OptiPlex 9010/0M9KCM, BIOS A12 01/10/2013
 0000000000000001 ffff880209983ca8 ffffffff816f514f 0000000000000000
 ffff8802099b8990 ffff880209983cd8 ffffffff810bd687 00000000000fee00
 ffff880208a2c000 ffff880208a10000 ffff88020ef50040 ffff880209983d08
Call Trace:
 [<ffffffff816f514f>] dump_stack+0x4e/0x71
 [<ffffffff810bd687>] lockdep_rcu_suspicious+0xe7/0x120
 [<ffffffffa037d055>] gfn_to_memslot+0xd5/0xe0 [kvm]
 [<ffffffffa03807d3>] __gfn_to_pfn+0x33/0x60 [kvm]
 [<ffffffffa0380885>] gfn_to_page+0x25/0x90 [kvm]
 [<ffffffffa038aeec>] kvm_vcpu_reload_apic_access_page+0x3c/0x80 [kvm]
 [<ffffffffa08f0a9c>] vmx_vcpu_reset+0x20c/0x460 [kvm_intel]
 [<ffffffffa039ab8e>] kvm_vcpu_reset+0x15e/0x1b0 [kvm]
 [<ffffffffa039ac0c>] kvm_arch_vcpu_setup+0x2c/0x50 [kvm]
 [<ffffffffa037f7e0>] kvm_vm_ioctl+0x1d0/0x780 [kvm]
 [<ffffffff810bc664>] ? __lock_is_held+0x54/0x80
 [<ffffffff812231f0>] do_vfs_ioctl+0x300/0x520
 [<ffffffff8122ee45>] ? __fget+0x5/0x250
 [<ffffffff8122f0fa>] ? __fget_light+0x2a/0xe0
 [<ffffffff81223491>] SyS_ioctl+0x81/0xa0
 [<ffffffff816fed6d>] system_call_fastpath+0x16/0x1b
Reported-by: Takashi Iwai <tiwai@suse.de>
Reported-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Reviewed-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Tested-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Fixes: 38b99173Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

In order to access the shadow VMCS, we need to load it. At this point,
vmx->loaded_vmcs->vmcs and the actually loaded one start to differ. If
we now get preempted by Linux, vmx_vcpu_put and, on return, the
vmx_vcpu_load will work against the wrong vmcs. That can cause
copy_shadow_to_vmcs12 to corrupt the vmcs12 state.

Fix the issue by disabling preemption during the copy operation.
copy_vmcs12_to_shadow is safe from this issue as it is executed by
vmx_vcpu_run when preemption is already disabled before vmentry.

This bug is exposed by running Jailhouse within KVM on CPUs with
shadow VMCS support.  Jailhouse never expects an interrupt pending
vmexit, but the bug can cause it if, after copy_shadow_to_vmcs12
is preempted, the active VMCS happens to have the virtual interrupt
pending flag set in the CPU-based execution controls.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Commit d1442d85 ("KVM: x86: Handle errors when RIP is set during far
jumps") introduced a bug that caused the fix to be incomplete.  Due to
incorrect evaluation, far jump to segment with L bit cleared (i.e., 32-bit
segment) and RIP with any of the high bits set (i.e, RIP[63:32] != 0) set may
not trigger #GP.  As we know, this imposes a security problem.

In addition, the condition for two warnings was incorrect.

Fixes: d1442d85Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
[Add #ifdef CONFIG_X86_64 to avoid complaints of undefined behavior. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

A critical 3.18 regression fix from Rob, (thanks!)
A fix to avoid advertizing modes we can't support from Sinclair
  (welcome Sinclair!)
and a fix for an incorrect  hash key computation from me that is
  completely harmless, but can wait 'til the next merge window if necessary.
  (I can't really bother stable with this one).

* 'vmwgfx-fixes-3.18' of git://people.freedesktop.org/~thomash/linux:
  drm/vmwgfx: Filter out modes those cannot be supported by the current VRAM size.
  drm/vmwgfx: Fix hash key computation
  drm/vmwgfx: fix lock breakage

Pull staging fixes from Greg KH:
 "Here are some staging driver fixes for 3.18-rc3.  Mostly iio and
  comedi driver fixes for issues reported by people.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'staging-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: comedi: fix memory leak / bad pointer freeing for chanlist
  staging: comedi: Kconfig: fix config COMEDI_ADDI_APCI_3120 dependants
  staging: comedi: widen subdevice number argument in ioctl handlers
  staging: rtl8723au: Fix alignment of mac_addr for ether_addr_copy() usage
  drivers/staging/comedi/Kconfig: Let COMEDI_II_PCI20KC depend on HAS_IOMEM
  staging: comedi: (regression) channel list must be set for COMEDI_CMD ioctl
  iio: adc: mxs-lradc: Disable the clock on probe failure
  iio: st_sensors: Fix buffer copy
  staging:iio:ad5933: Drop "raw" from channel names
  staging:iio:ad5933: Fix NULL pointer deref when enabling buffer

Pull USB fixes from Greg KH:
 "Here are a bunch of USB fixes for 3.18-rc3.

  Mostly usb-serial device ids and gadget fixes for issues that have
  been reported.  Full details are in the shortlog.

  All of these have been in linux-next for a while"

* tag 'usb-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (42 commits)
  usb: chipidea: Fix oops when removing the ci_hdrc module
  usb: gadget: function: Fixed the return value on error path
  usb: dwc2: gadget: disable phy before turning off power regulators
  usb: gadget: function: Remove redundant usb_free_all_descriptors
  usb: dwc3: gadget: Properly initialize LINK TRB
  usb: dwc2: gadget: fix gadget unregistration in udc_stop() function
  usb: dwc2: Bits in bitfield should add up to 32
  usb: dwc2: gadget: sparse warning of context imbalance
  usb: gadget: udc: core: fix kernel oops with soft-connect
  usb: musb: musb_dsps: fix NULL pointer in suspend
  usb: musb: dsps: start OTG timer on resume again
  usb: gadget: loopback: don't queue requests to bogus endpoints
  usb: ffs: fix regression when quirk_ep_out_aligned_size flag is set
  usb: gadget: f_fs: remove redundant ffs_data_get()
  usb: gadget: udc: USB_GADGET_XILINX should depend on HAS_DMA
  Revert "usb: dwc3: dwc3-omap: Disable/Enable only wrapper interrupts in prepare/complete"
  usb: gadget: composite: enable BESL support
  usb: musb: cppi41: restart hrtimer only if not yet done
  usb: dwc3: ep0: fix Data Phase for transfer sizes aligned to wMaxPacketSize
  usb: serial: ftdi_sio: add "bricked" FTDI device PID
  ...

Pull btrfs fixes from Chris Mason:
 "Filipe is nailing down some problems with our skinny extent variation,
  and Dave's patch fixes endian problems in the new super block checks"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: fix race that makes btrfs_lookup_extent_info miss skinny extent items
  Btrfs: properly clean up btrfs_end_io_wq_cache
  Btrfs: fix invalid leaf slot access in btrfs_lookup_extent()
  btrfs: use macro accessors in superblock validation checks

Pull input updates from Dmitry Torokhov:
 "A bunch of fixes for minor defects reported by Coverity, a few driver
  fixups and revert of i8042.nomux change so that we are once again
  enable active MUX mode if box claims to support it"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Revert "Input: i8042 - disable active multiplexing by default"
  Input: altera_ps2 - use correct type for irq return value
  Input: altera_ps2 - write to correct register when disabling interrupts
  Input: max77693-haptic - fix potential overflow
  Input: psmouse - remove unneeded check in psmouse_reconnect()
  Input: vsxxxaa - fix code dropping bytes from queue
  Input: ims-pcu - fix dead code in ims_pcu_ofn_reg_addr_store()
  Input: opencores-kbd - fix error handling
  Input: wm97xx - adapt parameters to tosa touchscreen.
  Input: i8042 - quirks for Fujitsu Lifebook A544 and Lifebook AH544
  Input: stmpe-keypad - fix valid key line bitmask
  Input: soc_button_array - update calls to gpiod_get*()

Pull ACPI and power management fixes from Rafael Wysocki:
 "These are fixes received after my previous pull request plus one that
  has been in the works for quite a while, but its previous version
  caused problems to happen, so it's been deferred till now.

  Fixed are two recent regressions (MFD enumeration and cpufreq-dt),
  ACPI EC regression introduced in 3.17, system suspend error code path
  regression introduced in 3.15, an older bug related to recovery from
  failing resume from hibernation and a cpufreq-dt driver issue related
  to operation performance points.

  Specifics:

   - Fix a crash on r8a7791/koelsch during resume from system suspend
     caused by a recent cpufreq-dt commit (Geert Uytterhoeven).

   - Fix an MFD enumeration problem introduced by a recent commit adding
     ACPI support to the MFD subsystem that exposed a weakness in the
     ACPI core causing ACPI enumeration to be applied to all devices
     associated with one ACPI companion object, although it should be
     used for one of them only (Mika Westerberg).

   - Fix an ACPI EC regression introduced during the 3.17 cycle causing
     some Samsung laptops to misbehave as a result of a workaround
     targeted at some Acer machines.  That includes a revert of a commit
     that went too far and a quirk for the Acer machines in question.
     From Lv Zheng.

   - Fix a regression in the system suspend error code path introduced
     during the 3.15 cycle that causes it to fail to take errors from
     asychronous execution of "late" suspend callbacks into account
     (Imre Deak).

   - Fix a long-standing bug in the hibernation resume error code path
     that fails to roll back everything correcty on "freeze" callback
     errors and leaves some devices in a "suspended" state causing more
     breakage to happen subsequently (Imre Deak).

   - Make the cpufreq-dt driver disable operation performance points
     that are not supported by the VR connected to the CPU voltage plane
     with acceptable tolerance instead of constantly failing voltage
     scaling later on (Lucas Stach)"

* tag 'pm+acpi-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / EC: Fix regression due to conflicting firmware behavior between Samsung and Acer.
  Revert "ACPI / EC: Add support to disallow QR_EC to be issued before completing previous QR_EC"
  cpufreq: cpufreq-dt: Restore default cpumask_setall(policy->cpus)
  PM / Sleep: fix recovery during resuming from hibernation
  PM / Sleep: fix async suspend_late/freeze_late error handling
  ACPI: Use ACPI companion to match only the first physical device
  cpufreq: cpufreq-dt: disable unsupported OPPs

Pull PCI fixes from Bjorn Helgaas:
 "These changes, intended for v3.18, fix:

  Sysfs
    - Fix "enable" filename change (Greg Kroah-Hartman)

      An unintentional sysfs filename change in commit 5136b2da
      ("PCI: convert bus code to use dev_groups"), which appeared in
      v3.13, changed "enable" to "enabled", and this changes it back.

      Old users of "enable" are currently broken and will be helped by
      this change.  Anything that started to use "enabled" after v3.13
      will be broken by this change.  If necessary, we can add a symlink
      to make both work, but this patch doesn't do that.

  PCI device hotplug
    - Revert duplicate merge (Kamal Mostafa)

      A mistaken duplicate merge that added a check twice.  Nothing's
      broken; this just removes the unnecessary code.

  Freescale i.MX6
    - Wait for clocks to stabilize after ref_en (Richard Zhu)

      An i.MX6 clock problem that prevents mx6 nitrogen boards from booting"

* tag 'pci-v3.18-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: Rename sysfs 'enabled' file back to 'enable'
  PCI: imx6: Wait for clocks to stabilize after ref_en
  Revert duplicate "PCI: pciehp: Prevent NULL dereference during probe"

Rusty noticed a Really Bad Bug (tm) in my NT fix.  The entry code
reads out of bounds, causing the NT fix to be unreliable.  But, and
this is much, much worse, if your stack is somehow just below the
top of the direct map (or a hole), you read out of bounds and crash.

Excerpt from the crash:

[    1.129513] RSP: 0018:ffff88001da4bf88  EFLAGS: 00010296

  2b:*    f7 84 24 90 00 00 00     testl  $0x4000,0x90(%rsp)

That read is deterministically above the top of the stack.  I
thought I even single-stepped through this code when I wrote it to
check the offset, but I clearly screwed it up.

Fixes: 8c7aa698 ("x86_64, entry: Filter RFLAGS.NT on entry from userspace")
Reported-by: Rusty Russell <rusty@ozlabs.org>
Cc: stable@vger.kernel.org
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ext4 bugfixes from Ted Ts'o:
 "A set of miscellaneous ext4 bug fixes for 3.18"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: make ext4_ext_convert_to_initialized() return proper number of blocks
  ext4: bail early when clearing inode journal flag fails
  ext4: bail out from make_indexed_dir() on first error
  jbd2: use a better hash function for the revoke table
  ext4: prevent bugon on race between write/fcntl
  ext4: remove extent status procfs files if journal load fails
  ext4: disallow changing journal_csum option during remount
  ext4: enable journal checksum when metadata checksum feature enabled
  ext4: fix oops when loading block bitmap failed
  ext4: fix overflow when updating superblock backups after resize

Pull quota and ext3 fixes from Jan Kara.

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  fs, jbd: use a more generic hash function
  quota: Properly return errors from dquot_writeback_dquots()
  ext3: Don't check quota format when there are no quota files