Currently, NETLINK_LIST_MEMBERSHIPS grabs the netlink table while copying
the membership state to user-space. However, grabing the netlink table is
effectively a write_lock_irq(), and as such we should not be triggering
page-faults in the critical section.

This can be easily reproduced by the following snippet:
    int s = socket(AF_NETLINK, SOCK_RAW, NETLINK_ROUTE);
    void *p = mmap(0, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANON, -1, 0);
    int r = getsockopt(s, 0x10e, 9, p, (void*)((char*)p + 4092));

This should work just fine, but currently triggers EFAULT and a possible
WARN_ON below handle_mm_fault().

Fix this by reducing locking of NETLINK_LIST_MEMBERSHIPS to a read-side
lock. The write-lock was overkill in the first place, and the read-lock
allows page-faults just fine.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for the TI DP83848 Ethernet PHY device.

The DP83848 is a highly reliable, feature rich, IEEE 802.3 compliant
single port 10/100 Mb/s Ethernet Physical Layer Transceiver supporting
the MII and RMII interfaces.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix sun4i-emac not releasing the following resources:
-iomapped memory not released on probe-failure nor on remove
-clock not getting disabled on probe-failure nor on remove
-sram not being released on remove

And while at it also add error checking to the clk_prepare_enable call
done on probe.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If userspace provides a ct action with no nested mark or label, then the
storage for these fields is zeroed. Later when actions are requested,
such zeroed fields are serialized even though userspace didn't
originally specify them. Fix the behaviour by ensuring that no action is
serialized in this case, and reject actions where userspace attempts to
set these fields with mask=0. This should make netlink marshalling
consistent across deserialization/reserialization.
Reported-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

New, related connections are marked as such as part of ovs_ct_lookup(),
but they are not marked as "new" if the commit flag is used. Make this
consistent by setting the "new" flag whenever !nf_ct_is_confirmed(ct).
Reported-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The presence of this attribute does not modify the ct_state for the
current packet, only future packets. Make this more clear in the header
definition.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, 0-bits are generated in ct_state where the bit position is
undefined, and matches are accepted on these bit-positions. If userspace
requests to match the 0-value for this bit then it may expect only a
subset of traffic to match this value, whereas currently all packets
will have this bit set to 0. Fix this by rejecting such masks.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit e520af48 introduced the following bug when setting the
TCP_REPAIR sockoption:

[ 2860.657036] BUG: using __this_cpu_add() in preemptible [00000000] code: daemon/12164
[ 2860.657045] caller is __this_cpu_preempt_check+0x13/0x20
[ 2860.657049] CPU: 1 PID: 12164 Comm: daemon Not tainted 4.2.3 #1
[ 2860.657051] Hardware name: Dell Inc. PowerEdge R210 II/0JP7TR, BIOS 2.0.5 03/13/2012
[ 2860.657054]  ffffffff81c7f071 ffff880231e9fdf8 ffffffff8185d765 0000000000000002
[ 2860.657058]  0000000000000001 ffff880231e9fe28 ffffffff8146ed91 ffff880231e9fe18
[ 2860.657062]  ffffffff81cd1a5d ffff88023534f200 ffff8800b9811000 ffff880231e9fe38
[ 2860.657065] Call Trace:
[ 2860.657072]  [<ffffffff8185d765>] dump_stack+0x4f/0x7b
[ 2860.657075]  [<ffffffff8146ed91>] check_preemption_disabled+0xe1/0xf0
[ 2860.657078]  [<ffffffff8146edd3>] __this_cpu_preempt_check+0x13/0x20
[ 2860.657082]  [<ffffffff817e0bc7>] tcp_xmit_probe_skb+0xc7/0x100
[ 2860.657085]  [<ffffffff817e1e2d>] tcp_send_window_probe+0x2d/0x30
[ 2860.657089]  [<ffffffff817d1d8c>] do_tcp_setsockopt.isra.29+0x74c/0x830
[ 2860.657093]  [<ffffffff817d1e9c>] tcp_setsockopt+0x2c/0x30
[ 2860.657097]  [<ffffffff81767b74>] sock_common_setsockopt+0x14/0x20
[ 2860.657100]  [<ffffffff817669e1>] SyS_setsockopt+0x71/0xc0
[ 2860.657104]  [<ffffffff81865172>] entry_SYSCALL_64_fastpath+0x16/0x75

Since tcp_xmit_probe_skb() can be called from process context, use
NET_INC_STATS() instead of NET_INC_STATS_BH().

Fixes: e520af48 ("tcp: add TCPWinProbe and TCPKeepAlive SNMP counters")
Signed-off-by: Renato Westphal <renatow@taghos.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains four Netfilter fixes for net, they are:

1) Fix Kconfig dependencies of new nf_dup_ipv4 and nf_dup_ipv6.

2) Remove bogus test nh_scope in IPv4 rpfilter match that is breaking
   --accept-local, from Xin Long.

3) Wait for RCU grace period after dropping the pending packets in the
   nfqueue, from Florian Westphal.

4) Fix sleeping allocation while holding spin_lock_bh, from Nikolay Borisov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit d999297c ("tipc: reduce locking scope during packet reception")
we altered the packet retransmission function. Since then, when
restransmitting packets, we create a clone of the original buffer
using __pskb_copy(skb, MIN_H_SIZE), where MIN_H_SIZE is the size of
the area we want to have copied, but also the smallest possible TIPC
packet size. The value of MIN_H_SIZE is 24.

Unfortunately, __pskb_copy() also has the effect that the headroom
of the cloned buffer takes the size MIN_H_SIZE. This is too small
for carrying the packet over the UDP tunnel bearer, which requires
a minimum headroom of 28 bytes. A change to just use pskb_copy()
lets the clone inherit the original headroom of 80 bytes, but also
assumes that the copied data area is of at least that size, something
that is not always the case. So that is not a viable solution.

We now fix this by adding a check for sufficient headroom in the
transmit function of udp_media.c, and expanding it when necessary.

Fixes: commit d999297c ("tipc: reduce locking scope during packet reception")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

CONFIG_NET_VENDOR_CAVIUM is only used to hide/show config options and to
include subdirectories in the build, so it doesn't make sense to make it
tristate.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current code for message reassembly is erroneously assuming that
the the first arriving fragment buffer always is linear, and then goes
ahead resetting the fragment list of that buffer in anticipation of
more arriving fragments.

However, if the buffer already happens to be non-linear, we will
inadvertently drop the already attached fragment list, and later
on trig a BUG() in __pskb_pull_tail().

We see this happen when running fragmented TIPC multicast across UDP,
something made possible since
commit d0f91938 ("tipc: add ip/udp media type")

We fix this by not resetting the fragment list when the buffer is non-
linear, and by initiatlizing our private fragment list tail pointer to
the tail of the existing fragment list.

Fixes: commit d0f91938 ("tipc: add ip/udp media type")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

"openvswitch: Remove vport stats" removed the per-vport statistics, in
order to use the netdev's statistics fields.
"openvswitch: Fix ovs_vport_get_stats()" fixed the export of these stats
to user-space, by using the provided netdev_ops to collate them - but ovs
internal devices still use an unallocated dev->tstats field to count
packets, which are no longer exported by this api.

Allocate the dev->tstats field for ovs internal devices, and wire up
ndo_get_stats64 with the original implementation of
ovs_vport_get_stats().

On its own, "openvswitch: Fix ovs_vport_get_stats()" fixes the OOPs,
unmasking a full-on panic on arm64:

=============%<==============
[<ffffffbffc00ce4c>] internal_dev_recv+0xa8/0x170 [openvswitch]
[<ffffffbffc0008b4>] do_output.isra.31+0x60/0x19c [openvswitch]
[<ffffffbffc000bf8>] do_execute_actions+0x208/0x11c0 [openvswitch]
[<ffffffbffc001c78>] ovs_execute_actions+0xc8/0x238 [openvswitch]
[<ffffffbffc003dfc>] ovs_packet_cmd_execute+0x21c/0x288 [openvswitch]
[<ffffffc0005e8c5c>] genl_family_rcv_msg+0x1b0/0x310
[<ffffffc0005e8e60>] genl_rcv_msg+0xa4/0xe4
[<ffffffc0005e7ddc>] netlink_rcv_skb+0xb0/0xdc
[<ffffffc0005e8a94>] genl_rcv+0x38/0x50
[<ffffffc0005e76c0>] netlink_unicast+0x164/0x210
[<ffffffc0005e7b70>] netlink_sendmsg+0x304/0x368
[<ffffffc0005a21c0>] sock_sendmsg+0x30/0x4c
[SNIP]
Kernel panic - not syncing: Fatal exception in interrupt
=============%<==============

Fixes: 8c876639 ("openvswitch: Remove vport stats.")
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

6e28b000 ("net: Fix vti use case with oif in dst lookups for IPv6")
is missing the checks on FLOWI_FLAG_SKIP_NH_OIF. Add them.

Fixes: 42a7b32b ("xfrm: Add oif to dst lookups")
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The default fix broadcast window size is currently set to 20 packets.
This is a very low value, set at a time when we were still testing on
10 Mb/s hubs, and a change to it is long overdue.

Commit 7845989c ("net: tipc: fix stall during bclink wakeup procedure")
revealed a problem with this low value. For messages of importance LOW,
the backlog queue limit will be  calculated to 30 packets, while a
single, maximum sized message of 66000 bytes, carried across a 1500 MTU
network consists of 46 packets.

This leads to the following scenario (among others leading to the same
situation):

1: Msg 1 of 46 packets is sent. 20 packets go to the transmit queue, 26
   packets to the backlog queue.
2: Msg 2 of 46 packets is attempted sent, but rejected because there is
   no more space in the backlog queue at this level. The sender is added
   to the wakeup queue with a "pending packets chain size" number of 46.
3: Some packets in the transmit queue are acked and released. We try to
   wake up the sender, but the pending size of 46 is bigger than the LOW
   wakeup limit of 30, so this doesn't happen.
5: Subsequent acks releases all the remaining buffers. Each time we test
   for the wakeup criteria and find that 46 still is larger than 30,
   even after both the transmit and the backlog queues are empty.
6: The sender is never woken up and given a chance to send its message.
   He is stuck.

We could now loosen the wakeup criteria (used by link_prepare_wakeup())
to become equal to the send criteria (used by tipc_link_xmit()), i.e.,
by ignoring the "pending packets chain size" value altogether, or we can
just increase the queue limits so that the criteria can be satisfied
anyway. There are good reasons (potentially multiple waiting senders) to
not opt for the former solution, so we choose the latter one.

This commit fixes the problem by giving the broadcast link window a
default value of 50 packets. We also introduce a new minimum link
window size BCLINK_MIN_WIN of 32, which is enough to always avoid the
described situation. Finally, in order to not break any existing users
which may set the window explicitly, we enforce that the window is set
to the new minimum value in case the user is trying to set it to
anything lower.

Fixes: 7845989c ("net: tipc: fix stall during bclink wakeup procedure")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is decrementing the pointer, instead of the value stored in the
pointer.  KASan detects it as an out of bounds reference.
Reported-by: "Berry Cheng 程君(成淼)" <chengmiao.cj@alibaba-inc.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sometimes xennet_create_queues() may failed to created all requested
queues, we need to update num_queues to real created to avoid NULL
pointer dereference.
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

reset transport and unlock if misc_register failed.
Signed-off-by: Gao feng <omarapazanadi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Philipp Kirchhofer says:

====================
net: mv643xx_eth: TSO TX data corruption fixes

as previously discussed [1] the mv643xx_eth driver has some
issues with data corruption when using TCP segmentation offload (TSO).

The following patch set improves this situation by fixing two data
corruption bugs in the TSO TX path.

Before applying the patches repeatedly accessing large files located on
a SMB share on my NSA325 NAS with TSO enabled resulted in different
hash sums, which confirmed that data corruption is happening during
file transfer. After applying the patches the hash sums were the same.

As this is my first patch submission please feel free to point out any
issues with the patch set.

[1] http://thread.gmane.org/gmane.linux.network/336530
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

To prevent a race between the TX DMA engine and the CPU the writing of the
first transmit descriptor must be deferred until all following descriptors
have been updated. The network card may otherwise start transmitting before
all packet descriptors are set up correctly, which leads to data corruption
or an aborted transmit operation.

This deferral is already done in the non-TSO TX path, implement it also in
the TSO TX path.
Signed-off-by: Philipp Kirchhofer <philipp@familie-kirchhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The TX DMA engine requires that buffers with a size of 8 bytes or smaller
must be 64 bit aligned. This requirement may be violated when doing TSO,
as in this case larger skb frags can be broken up and transmitted in small
parts with then inappropriate alignment.

Fix this by checking for proper alignment before handing a buffer to the
DMA engine. If the data is misaligned realign it by copying it into the
TSO header data area.
Signed-off-by: Philipp Kirchhofer <philipp@familie-kirchhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiko Schocher says:

====================
net, phy, smsc: add posibility to disable energy detect mode

On some boards the energy enable detect mode leads in
trouble with some switches, so make the enabling of
this mode configurable through DT.
Therefore the property "smsc,disable-energy-detect" is
introduced.

Patch 1 introduces phy-handle support for the ti,cpsw
driver. This is needed now for the smsc phy.

Patch 2 adds the disable energy mode functionality
to the smsc phy

Changes in v2:
- add comments from Florian Fainelli
  - I did not change disable property name into enable
    because I fear to break existing behaviour
  - add smsc vendor prefix
  - remove CONFIG_OF and use __maybe_unused
  - introduce "phy-handle" ability into ti,cpsw
    driver, so I can remove bogus:
      if (!of_node && dev->parent->of_node)
          of_node = dev->parent->of_node;
    construct. Therefore new patch for the ti,cpsw
    driver is necessary.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

On some boards the energy enable detect mode leads in
trouble with some switches, so make the enabling of
this mode configurable through DT.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

add the ability to parse "phy-handle". This
is needed for phys, which have a DT node, and
need to parse DT properties.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

If a gigabit ethernet PHY is connected to a fast ethernet MAC,
then it can detect 1000 support from the partner but not use it.

This results in a forced speed of 1000 and RX/TX failure.

Check for 1000BASE-T support and then check the advertisement
configuration before setting the MAC speed to 1000mbit.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Account for extra headroom in ath9k driver, from Felix Fietkau.

 2) Fix OOPS in pppoe driver due to incorrect socket state transition,
    from Guillaume Nault.

 3) Kill memory leak in amd-xgbe debugfx, from Geliang Tang.

 4) Power management fixes for iwlwifi, from Johannes Berg.

 5) Fix races in reqsk_queue_unlink(), from Eric Dumazet.

 6) Fix dst_entry usage in ARP replies, from Jiri Benc.

 7) Cure OOPSes with SO_GET_FILTER, from Daniel Borkmann.

 8) Missing allocation failure check in amd-xgbe, from Tom Lendacky.

 9) Various resource allocation/freeing cures in DSA< from Neil
    Armstrong.

10) A series of bug fixes in the openvswitch conntrack support, from
    Joe Stringer.

11) Fix two cases (BPF and act_mirred) where we have to clean the sender
    cpu stored in the SKB before transmitting.  From WANG Cong and
    Alexei Starovoitov.

12) Disable VLAN filtering in promiscuous mode in mlx5 driver, from
    Achiad Shochat.

13) Older bnx2x chips cannot do 4-tuple UDP hashing, so prevent this
    configuration via ethtool.  From Yuval Mintz.

14) Don't call rt6_uncached_list_flush_dev() from rt6_ifdown() when
    'dev' is NULL, from Eric Biederman.

15) Prevent stalled link synchronization in tipc, from Jon Paul Maloy.

16) kcalloc() gstrings ethtool buffer before having driver fill it in,
    in order to prevent kernel memory leaking.  From Joe Perches.

17) Fix mixxing rt6_info initialization for blackhole routes, from
    Martin KaFai Lau.

18) Kill VLAN regression in via-rhine, from Andrej Ota.

19) Missing pfmemalloc check in sk_add_backlog(), from Eric Dumazet.

20) Fix spurious MSG_TRUNC signalling in netlink dumps, from Ronen Arad.

21) Scrube SKBs when pushing them between namespaces in openvswitch,
    from Joe Stringer.

22) bcmgenet enables link interrupts too early, fix from Florian
    Fainelli.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (92 commits)
  net: bcmgenet: Fix early link interrupt enabling
  tunnels: Don't require remote endpoint or ID during creation.
  openvswitch: Scrub skb between namespaces
  xen-netback: correctly check failed allocation
  net: asix: add support for the Billionton GUSB2AM-1G-B USB adapter
  netlink: Trim skb to alloc size to avoid MSG_TRUNC
  net: add pfmemalloc check in sk_add_backlog()
  via-rhine: fix VLAN receive handling regression.
  ipv6: Initialize rt6_info properly in ip6_blackhole_route()
  ipv6: Move common init code for rt6_info to a new function rt6_info_init()
  Bluetooth: Fix initializing conn_params in scan phase
  Bluetooth: Fix conn_params list update in hci_connect_le_scan_cleanup
  Bluetooth: Fix remove_device behavior for explicit connects
  Bluetooth: Fix LE reconnection logic
  Bluetooth: Fix reference counting for LE-scan based connections
  Bluetooth: Fix double scan updates
  mlxsw: core: Fix race condition in __mlxsw_emad_transmit
  tipc: move fragment importance field to new header position
  ethtool: Use kcalloc instead of kmalloc for ethtool_get_strings
  tipc: eliminate risk of stalled link synchronization
  ...

Link interrupts are enabled in init_umac(), which is too early for us to
process them since we do not yet have a valid PHY device pointer. On
BCM7425 chips for instance, we will crash calling phy_mac_interrupt()
because phydev is NULL.

Fix this by moving the link interrupts enabling in
bcmgenet_netif_start(), under a specific function:
bcmgenet_link_intr_enable() and while at it, update the comments
surrounding the code.

Fixes: 6cc8e6d4 ("net: bcmgenet: Delay PHY initialization to bcmgenet_open()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2015-10-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
iwlwifi:

* mvm: flush fw_dump_wk when mvm fails to start
* mvm: init card correctly on ctkill exit check
* pci: add a few more PCI subvendor IDs for the 7265 series
* fix firmware filename for 3160
* mvm: clear csa countdown when AP is stopped
* mvm: fix D3 firmware PN programming
* dvm: fix D3 firmware PN programming
* mvm: fix D3 CCMP TX PN assignment

rtlwifi:

* rtl8821ae: Fix system lockups on boot
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Before lightweight tunnels existed, it really didn't make sense to
create a tunnel that was not fully specified, such as without a
destination IP address - the resulting packets would go nowhere.
However, with lightweight tunnels, the opposite is true - it doesn't
make sense to require this information when it will be provided later
on by the route. This loosens the requirements for this information.

An alternative would be to allow the relaxed version only when
COLLECT_METADATA is enabled. However, since there are several
variations on this theme (such as NBMA tunnels in GRE), just dropping
the restrictions seems the most consistent across tunnels and with
the existing configuration.

CC: John Linville <linville@tuxdriver.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

If OVS receives a packet from another namespace, then the packet should
be scrubbed. However, people have already begun to rely on the behaviour
that skb->mark is preserved across namespaces, so retain this one field.

This is mainly to address information leakage between namespaces when
using OVS internal ports, but by placing it in ovs_vport_receive() it is
more generally applicable, meaning it should not be overlooked if other
port types are allowed to be moved into namespaces in future.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Johan Hedberg says:

====================
pull request: bluetooth 2015-10-16

First of all, sorry for the late set of patches for the 4.3 cycle. We
just finished an intensive week of testing at the Bluetooth UnPlugFest
and discovered (and fixed) issues there. Unfortunately a few issues
affect 4.3-rc5 in a way that they break existing Bluetooth LE mouse and
keyboard support.

The regressions result from supporting LE privacy in conjunction with
scanning for Resolvable Private Addresses before connecting. A feature
that has been tested heavily (including automated unit tests), but sadly
some regressions slipped in. The UnPlugFest with its multitude of test
platforms is a good battle testing ground for uncovering every corner
case.

The patches in this pull request focus only on fixing the regressions in
4.3-rc5. The patches look a bit larger since we also added comments in
the critical sections of the fixes to improve clarity.

I would appreciate if we can get these regression fixes to Linus
quickly. Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Since vzalloc can be failed in memory pressure,
writes -ENOMEM to xenstore to indicate error.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Just another AX88178-based 10/100/1000 USB-to-Ethernet dongle. This one
shows up in lsusb as: "ID 08dd:0114 Billionton Systems, Inc".
Signed-off-by: Chia-Sheng Chang <changchias@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Christoph Jaeger <cj@linux.com>
Cc: "Woojung.Huh@microchip.com" <Woojung.Huh@microchip.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Markus Elfring <elfring@users.sourceforge.net>
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: netdev@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

netlink_dump() allocates skb based on the calculated min_dump_alloc or
a per socket max_recvmsg_len.
min_alloc_size is maximum space required for any single netdev
attributes as calculated by rtnl_calcit().
max_recvmsg_len tracks the user provided buffer to netlink_recvmsg.
It is capped at 16KiB.
The intention is to avoid small allocations and to minimize the number
of calls required to obtain dump information for all net devices.

netlink_dump packs as many small messages as could fit within an skb
that was sized for the largest single netdev information. The actual
space available within an skb is larger than what is requested. It could
be much larger and up to near 2x with align to next power of 2 approach.

Allowing netlink_dump to use all the space available within the
allocated skb increases the buffer size a user has to provide to avoid
truncaion (i.e. MSG_TRUNG flag set).

It was observed that with many VLANs configured on at least one netdev,
a larger buffer of near 64KiB was necessary to avoid "Message truncated"
error in "ip link" or "bridge [-c[ompressvlans]] vlan show" when
min_alloc_size was only little over 32KiB.

This patch trims skb to allocated size in order to allow the user to
avoid truncation with more reasonable buffer size.
Signed-off-by: Ronen Arad <ronen.arad@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull i2c fixes from Wolfram Sang:
 "Here are some bugfixes for the I2C subsystem.

  Kieran found a flaw in the recently renewed wake irq handling.  Mika
  handled a user bug report where the ACPI info turned out to be
  unusable.  I updated MAINTAINERS so that such bug reports will sooner
  get to the right people.  Geert pointed me to a problem of some i2c
  drivers regarding PM which I fixed"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: designware: Do not use parameters from ACPI on Dell Inspiron 7348
  MAINTAINERS: add maintainers for Synopsis Designware I2C drivers
  i2c: designware-platdrv: enable RuntimePM before registering to the core
  i2c: s3c2410: enable RuntimePM before registering to the core
  i2c: rcar: enable RuntimePM before registering to the core
  i2c: return probe deferred status on dev_pm_domain_attach

ACPI SSCN/FMCN methods were originally added because then the platform can
provide the most accurate HCNT/LCNT values to the driver. However, this
seems not to be true for Dell Inspiron 7348 where using these causes the
touchpad to fail in boot:

  i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
  i2c_designware INT3433:00: i2c_dw_handle_tx_abort: lost arbitration
  i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
  i2c_designware INT3433:00: controller timed out

The values received from ACPI are (in fast mode):

  HCNT: 72
  LCNT: 160

this translates to following timings (input clock is 100MHz on Broadwell):

  tHIGH: 720 ns (spec min 600 ns)
  tLOW: 1600 ns (spec min 1300 ns)
  Bus period: 2920 ns (assuming 300 ns tf and tr)
  Bus speed: 342.5 kHz

Both tHIGH and tLOW are within the I2C specification.

The calculated values when ACPI parameters are not used are (in fast mode):

  HCNT: 87
  LCNT: 159

which translates to:

  tHIGH: 870 ns (spec min 600 ns)
  tLOW: 1590 ns (spec min 1300 ns)
  Bus period 3060 ns (assuming 300 ns tf and tr)
  Bus speed 326.8 kHz

These values are also within the I2C specification.

Since both ACPI and calculated values meet the I2C specification timing
requirements it is hard to say why the touchpad does not function properly
with the ACPI values except that the bus speed is higher in this case (but
still well below the max 400kHz).

Solve this by adding DMI quirk to the driver that disables using ACPI
parameters on this particulare machine.
Reported-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org

Merge branches 'irq-urgent-for-linus' and 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull irq/timer fixes from Thomas Gleixner:
 "irq: a fix for the new hierarchical MSI interrupt handling which
  unbreaks PCI=n configurations.

  timers: a fix for the new hrtimer clock offset update mechanism to
  ensure that the boot time offset is respected"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq/msi: Do not use pci_msi_[un]mask_irq as default methods

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timekeeping: Increment clock_was_set_seq in timekeeping_init()

Greg reported crashes hitting the following check in __sk_backlog_rcv()

	BUG_ON(!sock_flag(sk, SOCK_MEMALLOC));

The pfmemalloc bit is currently checked in sk_filter().

This works correctly for TCP, because sk_filter() is ran in
tcp_v[46]_rcv() before hitting the prequeue or backlog checks.

For UDP or other protocols, this does not work, because the sk_filter()
is ran from sock_queue_rcv_skb(), which might be called _after_ backlog
queuing if socket is owned by user by the time packet is processed by
softirq handler.

Fixes: b4b9e355 ("netvm: set PF_MEMALLOC as appropriate during SKB processing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Greg Thelen <gthelen@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 00590fdd introduced RCU locking in list type and in
doing so introduced a memory allocation in list_set_add, which
is done in an atomic context, due to the fact that ipset rcu
list modifications are serialised with a spin lock. The reason
why we can't use a mutex is that in addition to modifying the
list with ipset commands, it's also being modified when a
particular ipset rule timeout expires aka garbage collection.
This gc is triggered from set_cleanup_entries, which in turn
is invoked from a timer thus requiring the lock to be bh-safe.

Concretely the following call chain can lead to "sleeping function
called in atomic context" splat:
call_ad -> list_set_uadt -> list_set_uadd -> kzalloc(, GFP_KERNEL).
And since GFP_KERNEL allows initiating direct reclaim thus
potentially sleeping in the allocation path.

To fix the issue change the allocation type to GFP_ATOMIC, to
correctly reflect that it is occuring in an atomic context.

Fixes: 00590fdd ("netfilter: ipset: Introduce RCU locking in list type")
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>