The uuids debugfs should only be created together with the other
entries after the setup procedure has been finished.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The blacklist debugfs should only be created together with the other
entries after the setup procedure has been finished.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The device blacklist is not taking care of the address type. Actually
store the address type in the list entries and also use them when
looking up addresses in the table.

This is actually a serious bug. When adding a LE public address to
the blacklist, then it would be blocking a device on BR/EDR. And this
is not the expected behavior.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

For easier debugging of the current voice setting, expose the value
in debugfs if the controller is BR/EDR capable.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

For LE capable controllers, the static address can be configured. For
debugging purposes expose the value in debugfs.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The auto_accept_delay debugfs entry is only valid for BR/EDR capable
controllers that also support SSP. If SSP is not available or it is
a LE-only single mode controller this value has no affect and so do
not expose it.

Since the value can be actually changed, switch the permissions
to 0644 to clearly indicate that the value is indeed writeable.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The inquiry_cache debugfs entry is only valid for BR/EDR capable
controllers. In case of single mode LE-only controllers that
entry is not valid.

Move the creating of the debugfs entries to the end of controller
init and only create the inquiry_cache entry if BR/EDR is actually
supported.

At the same time this avoids creating any debugfs entries for
AMP controllers since none of the entries are valid there.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The L2CAP socket parameter for CID are actually provided in little
endian. So convert our constants into little endian before comparing
them.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

There is no need to use a timer since the entire Bluetooth subsystem
runs using workqueues these days.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Since the entire Bluetooth subsystem runs in workqueues these days there
is no need to use a timer for deferring work.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Right now we do not allow user space to use connection oriented channels
on LE, and the only CID that can be used is the Attribute Protocol one.
These restrictions went away together with the recent refactoring of the
L2CAP code, but this patch puts them back to their appropriate places.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This function should be operating on scan_rsp_data_len and scan_rsp_data
and not the advertising data variables.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This seems to be a left-over. The module parameter enable_hs has
been removed, but its extern declaration is still present. It is
not needed anymore, so just remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The SMP CID is only defined for LE transports. Instead of returning an
error from smp_sig_channel() in this case (which would cause a
disconnection) just return 0 to ignore the data, which is consistent
with the behavior for other unknown CIDs.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The A2MP CID is only valid for BR/EDR transports. We should ignore A2MP
data on non-BR/EDR links and refuse to create an amp_mgr object.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Now that the only reason code this function can return is
L2CAP_REJ_NOT_UNDERSTOOD we can just do the necessary assignment without
needing a separate function at all.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

There is no command handler that would return an EMSGSIZE error, so just
remove this mapping from the l2cap_err_to_reason function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When the reason code in the L2CAP command reject is "invalid CID" there
should be four additional bytes of data in the PDU, namely the source
and destination CIDs (which should be zero if one or both are not
applicable). This patch fixes all occurrences of such errors to return
the right kind of PDU.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The constants for advertising event types have been defined twice. So
remove one copy of it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Since there is update_scan_rsp_data, it is also better to use the
clear name update_adv_data instead of update_ad.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The scan response data is a better place to store the device name
since it has more space available and is also enforcing privacy.

When the controller is advertising, the connectable setting decides
if ADV_IND or ADV_NONCONN_IND is used. In case of ADV_IND, the
remote side is allowed to request the scan response data. Same as
with BR/EDR where either EIR is used or a remote name request. In
non-connectable mode, the device name is not available since it is
not allowed to request scan response data. Same as in BR/EDR where
the device is non-discoverable and no name requests are answered.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

On controller power on and when enabling LE functionality,
make sure that also the scan response data is correctly set.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The scan response data needs to be stored in HCI device and so
add a buffer for it and also ensure to clear it when resetting
the controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Rename the create_ad function into create_adv_data to make it clear
that it is used to create the advertising data. This is important
since later on a function adding the scan response data will be
added.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The return value of mgmt_new_ltk() function is not used and
so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

The return value of mgmt_read_local_oob_data_reply_complete() function
is not used and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

The return value of mgmt_set_local_name_complete() function is
not used and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

The return value of mgmt_set_class_of_dev_complete() function is
not used and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

The return value of mgmt_ssp_enable_complete() function is not
used and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

The return value of mgmt_auth_enable_complete() function is not
used and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

The return value of mgmt_auth_failed() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

The return value of mgmt_pin_code_neg_reply_complete() function is
not used and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

The return value of mgmt_pin_code_reply_complete() function is not
used and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

The return value of mgmt_pin_code_request() function is not used
and so just change it to return void.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

The A2MP client for L2CAP channels needs to use l2cap_chan_no_resume
empty stub function.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

In this case the replacement by l2cap_chan_ready() doesn't change the code
flow, the same operations will executed plus two others that have no
effect: the use of the parent socket, that a non-oriented channel doesn't
have and the reset of conf_state, which is also fine since the connection
is ready at this point.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The wait_ack code has a heavy dependency on the socket data structures
and, as of now, it won't be worthless change it to use non-socket
structures as the only user of such feature is a socket.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

We need to remove all direct access of struct sock from L2CAP core.
This change is pretty simple and just add a new L2CAP channel callback to
do the work in the L2CAP socket side.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

As part of the work to remove struct sock from l2cap_core.c and make it
more generic we remove in this commit the direct access to sk->sk_sndtimeo
member. This objective of this change is purely remove sk usage from
l2cap_core.c

Now we have a new l2cap ops to get the current value of sk->sndtimeo. A
l2cap_chan_no_get_sndtimeo was added for users of L2CAP that doesn't need
to set a timeout.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

l2cap_state_change_and_error() introduces the ability to update a
l2cap_user with changes in channel's state and error code with just one
call. The main reason for this is to avoid race conditions between and
setting the state and then the error. Otherwise we would need to release
the lock between both operations.

This is another step of an ongoing work to make l2cap_core.c totally
independent from l2cap's struct sock.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>