- 03 Dec, 2018 6 commits
-
-
David S. Miller authored
Yoshihiro Shimoda says: ==================== net: phy: micrel: add toggling phy reset This patch set is for R-Car Gen3 Salvator-XS boards. If we do the following method, the phy cannot link up correctly. 1) Kernel boots by using initramfs. --> No open the nic, so phy_device_register() and phy_probe() deasserts the reset. 2) Kernel enters the suspend. --> So, keep the reset signal as deassert. --> On R-Car Salvator-XS board, unfortunately, the board power is turned off. 3) Kernel returns from suspend. 4) ifconfig eth0 up --> Then, since edge signal of the reset doesn't happen, it cannot link up. 5) ifconfig eth0 down 6) ifconfig eth0 up --> In this case, it can link up. When resolving this issue after I got feedback from Andrew and Heiner, I found an issue that the phy_device.c didn't call phy_resume() if the PHY was not attached. So, patch 1 fixes it and add toggling the phy reset to the micrel phy driver. Changes from v1 (as RFC): - No remove the current code of phy_device.c to avoid any side effects. - Fix the mdio_bus_phy_resume() in phy_device.c. - Add toggling the phy reset in micrel.c if the PHY is not attached. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Yoshihiro Shimoda authored
This patch adds toggling phy reset if PHY is not attached. Otherwise, some boards (e.g. R-Car H3 Salvator-XS) cannot link up correctly if we do the following method: 1) Kernel boots by using initramfs. --> No open the nic, so phy_device_register() and phy_probe() deasserts the reset. 2) Kernel enters the suspend. --> So, keep the reset signal as deassert. --> On R-Car Salvator-XS board, unfortunately, the board power is turned off. 3) Kernel returns from suspend. 4) ifconfig eth0 up --> Then, since edge signal of the reset doesn't happen, it cannot link up. 5) ifconfig eth0 down 6) ifconfig eth0 up --> In this case, it can link up. Reported-by:Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com> Signed-off-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by:
-
Yoshihiro Shimoda authored
This patch fixes an issue that mdio_bus_phy_resume() doesn't call phy_resume() if the PHY is not attached. Fixes: 803dd9c7 ("net: phy: avoid suspending twice a PHY") Signed-off-by:
-
Prashant Bhole authored
In tun.c skb->len was accessed while doing stats accounting after a call to netif_receive_skb. We can not access skb after this call because buffers may be dropped. The fix for this bug would be to store skb->len in local variable and then use it after netif_receive_skb(). IMO using xdp data size for accounting bytes will be better because input for tun_xdp_one() is xdp_buff. Hence this patch: - fixes a bug by removing skb access after netif_receive_skb() - uses xdp data size for accounting bytes [613.019057] BUG: KASAN: use-after-free in tun_sendmsg+0x77c/0xc50 [tun] [613.021062] Read of size 4 at addr ffff8881da9ab7c0 by task vhost-1115/1155 [613.023073] [613.024003] CPU: 0 PID: 1155 Comm: vhost-1115 Not tainted 4.20.0-rc3-vm+ #232 [613.026029] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014 [613.029116] Call Trace: [613.031145] dump_stack+0x5b/0x90 [613.032219] print_address_description+0x6c/0x23c [613.034156] ? tun_sendmsg+0x77c/0xc50 [tun] [613.036141] kasan_report.cold.5+0x241/0x308 [613.038125] tun_sendmsg+0x77c/0xc50 [tun] [613.040109] ? tun_get_user+0x1960/0x1960 [tun] [613.042094] ? __isolate_free_page+0x270/0x270 [613.045173] vhost_tx_batch.isra.14+0xeb/0x1f0 [vhost_net] [613.047127] ? peek_head_len.part.13+0x90/0x90 [vhost_net] [613.049096] ? get_tx_bufs+0x5a/0x2c0 [vhost_net] [613.051106] ? vhost_enable_notify+0x2d8/0x420 [vhost] [613.053139] handle_tx_copy+0x2d0/0x8f0 [vhost_net] [613.053139] ? vhost_net_buf_peek+0x340/0x340 [vhost_net] [613.053139] ? __mutex_lock+0x8d9/0xb30 [613.053139] ? finish_task_switch+0x8f/0x3f0 [613.053139] ? handle_tx+0x32/0x120 [vhost_net] [613.053139] ? mutex_trylock+0x110/0x110 [613.053139] ? finish_task_switch+0xcf/0x3f0 [613.053139] ? finish_task_switch+0x240/0x3f0 [613.053139] ? __switch_to_asm+0x34/0x70 [613.053139] ? __switch_to_asm+0x40/0x70 [613.053139] ? __schedule+0x506/0xf10 [613.053139] handle_tx+0xc7/0x120 [vhost_net] [613.053139] vhost_worker+0x166/0x200 [vhost] [613.053139] ? vhost_dev_init+0x580/0x580 [vhost] [613.053139] ? __kthread_parkme+0x77/0x90 [613.053139] ? vhost_dev_init+0x580/0x580 [vhost] [613.053139] kthread+0x1b1/0x1d0 [613.053139] ? kthread_park+0xb0/0xb0 [613.053139] ret_from_fork+0x35/0x40 [613.088705] [613.088705] Allocated by task 1155: [613.088705] kasan_kmalloc+0xbf/0xe0 [613.088705] kmem_cache_alloc+0xdc/0x220 [613.088705] __build_skb+0x2a/0x160 [613.088705] build_skb+0x14/0xc0 [613.088705] tun_sendmsg+0x4f0/0xc50 [tun] [613.088705] vhost_tx_batch.isra.14+0xeb/0x1f0 [vhost_net] [613.088705] handle_tx_copy+0x2d0/0x8f0 [vhost_net] [613.088705] handle_tx+0xc7/0x120 [vhost_net] [613.088705] vhost_worker+0x166/0x200 [vhost] [613.088705] kthread+0x1b1/0x1d0 [613.088705] ret_from_fork+0x35/0x40 [613.088705] [613.088705] Freed by task 1155: [613.088705] __kasan_slab_free+0x12e/0x180 [613.088705] kmem_cache_free+0xa0/0x230 [613.088705] ip6_mc_input+0x40f/0x5a0 [613.088705] ipv6_rcv+0xc9/0x1e0 [613.088705] __netif_receive_skb_one_core+0xc1/0x100 [613.088705] netif_receive_skb_internal+0xc4/0x270 [613.088705] br_pass_frame_up+0x2b9/0x2e0 [613.088705] br_handle_frame_finish+0x2fb/0x7a0 [613.088705] br_handle_frame+0x30f/0x6c0 [613.088705] __netif_receive_skb_core+0x61a/0x15b0 [613.088705] __netif_receive_skb_one_core+0x8e/0x100 [613.088705] netif_receive_skb_internal+0xc4/0x270 [613.088705] tun_sendmsg+0x738/0xc50 [tun] [613.088705] vhost_tx_batch.isra.14+0xeb/0x1f0 [vhost_net] [613.088705] handle_tx_copy+0x2d0/0x8f0 [vhost_net] [613.088705] handle_tx+0xc7/0x120 [vhost_net] [613.088705] vhost_worker+0x166/0x200 [vhost] [613.088705] kthread+0x1b1/0x1d0 [613.088705] ret_from_fork+0x35/0x40 [613.088705] [613.088705] The buggy address belongs to the object at ffff8881da9ab740 [613.088705] which belongs to the cache skbuff_head_cache of size 232 Fixes: 043d222f ("tuntap: accept an array of XDP buffs through sendmsg()") Reviewed-by:
Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Signed-off-by:
Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp> Acked-by:
Jason Wang <jasowang@redhat.com> Acked-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
Su Yanjun authored
When changing mtu many times with traffic, a bug is triggered: [ 1035.684037] kernel BUG at lib/dynamic_queue_limits.c:26! [ 1035.684042] invalid opcode: 0000 [#1] SMP [ 1035.684049] Modules linked in: loop binfmt_misc 8139cp(OE) macsec tcp_diag udp_diag inet_diag unix_diag af_packet_diag netlink_diag tcp_lp fuse uinput xt_CHECKSUM iptable_mangle ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack ipt_REJECT nf_reject_ipv4 tun bridge stp llc ebtable_filter ebtables ip6table_filter devlink ip6_tables iptable_filter sunrpc snd_hda_codec_generic snd_hda_intel snd_hda_codec snd_hda_core snd_hwdep ppdev snd_seq iosf_mbi crc32_pclmul parport_pc snd_seq_device ghash_clmulni_intel parport snd_pcm aesni_intel joydev lrw snd_timer virtio_balloon sg gf128mul glue_helper ablk_helper cryptd snd soundcore i2c_piix4 pcspkr ip_tables xfs libcrc32c sr_mod sd_mod cdrom crc_t10dif crct10dif_generic ata_generic [ 1035.684102] pata_acpi virtio_console qxl drm_kms_helper syscopyarea sysfillrect sysimgblt floppy fb_sys_fops crct10dif_pclmul crct10dif_common ttm crc32c_intel serio_raw ata_piix drm libata 8139too virtio_pci drm_panel_orientation_quirks virtio_ring virtio mii dm_mirror dm_region_hash dm_log dm_mod [last unloaded: 8139cp] [ 1035.684132] CPU: 9 PID: 25140 Comm: if-mtu-change Kdump: loaded Tainted: G OE ------------ T 3.10.0-957.el7.x86_64 #1 [ 1035.684134] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 [ 1035.684136] task: ffff8f59b1f5a080 ti: ffff8f5a2e32c000 task.ti: ffff8f5a2e32c000 [ 1035.684149] RIP: 0010:[<ffffffffba3a40d0>] [<ffffffffba3a40d0>] dql_completed+0x180/0x190 [ 1035.684162] RSP: 0000:ffff8f5a75483e50 EFLAGS: 00010093 [ 1035.684162] RAX: 00000000000000c2 RBX: ffff8f5a6f91c000 RCX: 0000000000000000 [ 1035.684162] RDX: 0000000000000000 RSI: 0000000000000184 RDI: ffff8f599fea3ec0 [ 1035.684162] RBP: ffff8f5a75483ea8 R08: 00000000000000c2 R09: 0000000000000000 [ 1035.684162] R10: 00000000000616ef R11: ffff8f5a75483b56 R12: ffff8f599fea3e00 [ 1035.684162] R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000184 [ 1035.684162] FS: 00007fa8434de740(0000) GS:ffff8f5a75480000(0000) knlGS:0000000000000000 [ 1035.684162] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 1035.684162] CR2: 00000000004305d0 CR3: 000000024eb66000 CR4: 00000000001406e0 [ 1035.684162] Call Trace: [ 1035.684162] <IRQ> [ 1035.684162] [<ffffffffc08cbaf8>] ? cp_interrupt+0x478/0x580 [8139cp] [ 1035.684162] [<ffffffffba14a294>] __handle_irq_event_percpu+0x44/0x1c0 [ 1035.684162] [<ffffffffba14a442>] handle_irq_event_percpu+0x32/0x80 [ 1035.684162] [<ffffffffba14a4cc>] handle_irq_event+0x3c/0x60 [ 1035.684162] [<ffffffffba14db29>] handle_fasteoi_irq+0x59/0x110 [ 1035.684162] [<ffffffffba02e554>] handle_irq+0xe4/0x1a0 [ 1035.684162] [<ffffffffba7795dd>] do_IRQ+0x4d/0xf0 [ 1035.684162] [<ffffffffba76b362>] common_interrupt+0x162/0x162 [ 1035.684162] <EOI> [ 1035.684162] [<ffffffffba0c2ae4>] ? __wake_up_bit+0x24/0x70 [ 1035.684162] [<ffffffffba1e46f5>] ? do_set_pte+0xd5/0x120 [ 1035.684162] [<ffffffffba1b64fb>] unlock_page+0x2b/0x30 [ 1035.684162] [<ffffffffba1e4879>] do_read_fault.isra.61+0x139/0x1b0 [ 1035.684162] [<ffffffffba1e9134>] handle_pte_fault+0x2f4/0xd10 [ 1035.684162] [<ffffffffba1ebc6d>] handle_mm_fault+0x39d/0x9b0 [ 1035.684162] [<ffffffffba76f5e3>] __do_page_fault+0x203/0x500 [ 1035.684162] [<ffffffffba76f9c6>] trace_do_page_fault+0x56/0x150 [ 1035.684162] [<ffffffffba76ef42>] do_async_page_fault+0x22/0xf0 [ 1035.684162] [<ffffffffba76b788>] async_page_fault+0x28/0x30 [ 1035.684162] Code: 54 c7 47 54 ff ff ff ff 44 0f 49 ce 48 8b 35 48 2f 9c 00 48 89 77 58 e9 fe fe ff ff 0f 1f 80 00 00 00 00 41 89 d1 e9 ef fe ff ff <0f> 0b 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 55 8d 42 ff 48 [ 1035.684162] RIP [<ffffffffba3a40d0>] dql_completed+0x180/0x190 [ 1035.684162] RSP <ffff8f5a75483e50> It's not the same as in 7fe0ee09 patch described. As 8139cp uses shared irq mode, other device irq will trigger cp_interrupt to execute. cp_change_mtu -> cp_close -> cp_open In cp_close routine just before free_irq(), some interrupt may occur. In my environment, cp_interrupt exectutes and IntrStatus is 0x4, exactly TxOk. That will cause cp_tx to wake device queue. As device queue is started, cp_start_xmit and cp_open will run at same time which will cause kernel BUG. For example: [#] for tx descriptor At start: [#][#][#] num_queued=3 After cp_init_hw->cp_start_hw->netdev_reset_queue: [#][#][#] num_queued=0 When 8139cp starts to work then cp_tx will check num_queued mismatchs the complete_bytes. The patch will check IntrMask before check IntrStatus in cp_interrupt. When 8139cp interrupt is disabled, just return. Signed-off-by:
Su Yanjun <suyj.fnst@cn.fujitsu.com> Signed-off-by:
-
Heiner Kallweit authored
Currently __set_phy_supported allows to add modes w/o checking whether the PHY supports them. This is wrong, it should never add modes but only remove modes we don't want to support. The commit marked as fixed didn't do anything wrong, it just copied existing functionality to the helper which is being fixed now. Fixes: f3a6bd39 ("phylib: Add phy_set_max_speed helper") Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
- 01 Dec, 2018 10 commits
-
-
Nicolas Dichtel authored
It's not supported right now (the goal of the initial patch was to support 'ip link del' only). Before the patch: $ ip link add foo type tun [ 239.632660] BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 [snip] [ 239.636410] RIP: 0010:register_netdevice+0x8e/0x3a0 This panic occurs because dev->netdev_ops is not set by tun_setup(). But to have something usable, it will require more than just setting netdev_ops. Fixes: f019a7a5 ("tun: Implement ip link del tunXXX") CC: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by:
-
Jason Wang authored
We copy vnet header unconditionally in page_to_skb() this is wrong since XDP may modify the packet data. So let's keep a zeroed vnet header for not confusing the conversion between vnet header and skb metadata. In the future, we should able to detect whether or not the packet was modified and keep using the vnet header when packet was not touched. Fixes: f600b690 ("virtio_net: Add XDP support") Reported-by:
Pavel Popa <pashinho1990@gmail.com> Signed-off-by:
-
David S. Miller authored
Yuchung Cheng says: ==================== tcp: fixes in timeout and retransmission accounting This patch set has assorted fixes of minor accounting issues in timeout, window probe, and retransmission stats. ==================== Signed-off-by: -
Yuchung Cheng authored
Previously the SNMP TCPTIMEOUTS counter has inconsistent accounting: 1. It counts all SYN and SYN-ACK timeouts 2. It counts timeouts in other states except recurring timeouts and timeouts after fast recovery or disorder state. Such selective accounting makes analysis difficult and complicated. For example the monitoring system needs to collect many other SNMP counters to infer the total amount of timeout events. This patch makes TCPTIMEOUTS counter simply counts all the retransmit timeout (SYN or data or FIN). Signed-off-by:
Yuchung Cheng <ycheng@google.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
-
Yuchung Cheng authored
Previously the SNMP counter LINUX_MIB_TCPRETRANSFAIL is not counting the TSO/GSO properly on failed retransmission. This patch fixes that. Signed-off-by:
-
Yuchung Cheng authored
Previously there is an off-by-one bug on determining when to abort a stalled window-probing socket. This patch fixes that so it is consistent with tcp_write_timeout(). Signed-off-by:
-
Pan Bian authored
The function lio_vf_rep_packet_sent_callback releases the occupation of sc via octeon_free_soft_command. sc should not be used after that. Unfortunately, sc->iq_no is read. To fix this, the patch stores sc->iq_no into a local variable before releasing sc and then uses the local variable instead of sc->iq_no. Signed-off-by:
Pan Bian <bianpan2016@163.com> Signed-off-by:
-
Cong Wang authored
IP header is not necessarily located right after struct ethhdr, there could be multiple 802.1Q headers in between, this is why we call __vlan_get_protocol(). Fixes: fe1dc069 ("net/mlx5e: don't set CHECKSUM_COMPLETE on SCTP packets") Cc: Alaa Hleihel <alaa@mellanox.com> Cc: Or Gerlitz <ogerlitz@mellanox.com> Cc: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by:
Tariq Toukan <tariqt@mellanox.com> Acked-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
-
Florian Fainelli authored
While introducing the DSA tagging protocol attribute, it was added to the DSA slave network devices, but those actually see untagged traffic (that is their whole purpose). Correct this mistake by putting the tagging sysfs attribute under the DSA master network device where this is the information that we need. While at it, also correct the sysfs documentation mistake that missed the "dsa/" directory component of the attribute. Fixes: 98cdb480 ("net: dsa: Expose tagging protocol to user-space") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Reviewed-by:
-
Davide Caratti authored
when users set an invalid control action, kmemleak complains as follows: # echo clear >/sys/kernel/debug/kmemleak # ./tdc.py -e b48b Test b48b: Add police action with exceed goto chain control action All test results: 1..1 ok 1 - b48b # Add police action with exceed goto chain control action about to flush the tap output if tests need to be skipped done flushing skipped test tap output # echo scan >/sys/kernel/debug/kmemleak # cat /sys/kernel/debug/kmemleak unreferenced object 0xffffa0fafbc3dde0 (size 96): comm "tc", pid 2358, jiffies 4294922738 (age 17.022s) hex dump (first 32 bytes): 2a 00 00 20 00 00 00 00 00 00 7d 00 00 00 00 00 *.. ......}..... f8 07 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<00000000648803d2>] tcf_action_init_1+0x384/0x4c0 [<00000000cb69382e>] tcf_action_init+0x12b/0x1a0 [<00000000847ef0d4>] tcf_action_add+0x73/0x170 [<0000000093656e14>] tc_ctl_action+0x122/0x160 [<0000000023c98e32>] rtnetlink_rcv_msg+0x263/0x2d0 [<000000003493ae9c>] netlink_rcv_skb+0x4d/0x130 [<00000000de63f8ba>] netlink_unicast+0x209/0x2d0 [<00000000c3da0ebe>] netlink_sendmsg+0x2c1/0x3c0 [<000000007a9e0753>] sock_sendmsg+0x33/0x40 [<00000000457c6d2e>] ___sys_sendmsg+0x2a0/0x2f0 [<00000000c5c6a086>] __sys_sendmsg+0x5e/0xa0 [<00000000446eafce>] do_syscall_64+0x5b/0x180 [<000000004aa871f2>] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [<00000000450c38ef>] 0xffffffffffffffff change tcf_police_init() to avoid leaking 'new' in case TCA_POLICE_RESULT contains TC_ACT_GOTO_CHAIN extended action. Fixes: c08f5ed5 ("net/sched: act_police: disallow 'goto chain' on fallback control action") Reported-by:Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Davide Caratti <dcaratti@redhat.com> Acked-by:
-
- 30 Nov, 2018 9 commits
-
-
John Hurley authored
For flow offload adds, if the rhash insert code fails, the flow will still have been offloaded but the reference to it in the driver freed. Re-order the offload setup calls to ensure that a flow will only be written to FW if a kernel reference is held and stored in the rhashtable. Remove this hashtable entry if the offload fails. Fixes: c01d0efa ("nfp: flower: use rhashtable for flow caching") Signed-off-by:
John Hurley <john.hurley@netronome.com> Reviewed-by:
Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Reviewed-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by:
-
John Hurley authored
Calling nfp_compile_flow_metadata both assigns a stats context and increments a ref counter on (or allocates) a mask id table entry. These are released by the nfp_modify_flow_metadata call on flow deletion, however, if a flow add fails after metadata is set then the flow entry will be deleted but the metadata assignments leaked. Add an error path to the flow add offload function to ensure allocated metadata is released in the event of an offload fail. Fixes: 81f3ddf2 ("nfp: add control message passing capabilities to flower offloads") Signed-off-by:
-
Toni Peltonen authored
Previously when unbinding a slave the 802.3ad implementation only told partner that the port is not suitable for aggregation by setting the port aggregation state from aggregatable to individual. This is not enough. If the physical layer still stays up and we only unbinded this port from the bond there is nothing in the aggregation status alone to prevent the partner from sending traffic towards us. To ensure that the partner doesn't consider this port at all anymore we should also disable collecting and distributing to signal that this actor is going away. Also clear AD_STATE_SYNCHRONIZATION to ensure partner exits collecting + distributing state. I have tested this behaviour againts Arista EOS switches with mlx5 cards (physical link stays up even when interface is down) and simulated the same situation virtually Linux <-> Linux with two network namespaces running two veth device pairs. In both cases setting aggregation to individual doesn't alone prevent traffic from being to sent towards this port given that the link stays up in partners end. Partner still keeps it's end in collecting + distributing state and continues until timeout is reached. In most cases this means we are losing the traffic partner sends towards our port while we wait for timeout. This is most visible with slow periodic time (LACP rate slow). Other open source implementations like Open VSwitch and libreswitch, and vendor implementations like Arista EOS, seem to disable collecting + distributing to when doing similar port disabling/detaching/removing change. With this patch kernel implementation would behave the same way and ensure partner doesn't consider our actor viable anymore. Signed-off-by:
Toni Peltonen <peltzi@peltzi.fi> Signed-off-by:
Jay Vosburgh <jay.vosburgh@canonical.com> Acked-by:
Jonathan Toppins <jtoppins@redhat.com> Signed-off-by:
-
Dmitry Bogdanov authored
The last set of csum offload fixes had a leak: Checksum enabled status bits from rx descriptor were incorrectly interpreted. Consequently all the other valid logic worked on zero bits. That caused rx checksum offloads never to trigger. Tested by dumping rx descriptors and validating resulting csum_level. Reported-by:
Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by:
Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by:
-
Colin Ian King authored
There is a spelling mistake in a net_warn_ratelimited message, fix this. Signed-off-by:
Colin Ian King <colin.king@canonical.com> Reviewed-by:
Simon Horman <simon.horman@netronome.com> Signed-off-by:
-
Colin Ian King authored
There is a spelling mistake in the oct_stats_strings array, fix it. Signed-off-by:
-
Thierry Reding authored
Setting up and tearing down debugfs is current unbalanced, as seen by this error during resume from suspend: [ 752.134067] dwc-eth-dwmac 2490000.ethernet eth0: ERROR failed to create debugfs directory [ 752.134347] dwc-eth-dwmac 2490000.ethernet eth0: stmmac_hw_setup: failed debugFS registration The imbalance happens because the driver creates the debugfs hierarchy when the device is opened and tears it down when the device is closed. There's little gain in that, and it could be argued that it is even surprising because it's not usually done for other devices. Fix the imbalance by moving the debugfs creation and teardown to the driver's ->probe() and ->remove() implementations instead. Note that the ring descriptors cannot be read while the interface is down, so make sure to return an empty file when the descriptors_status debugfs file is read. Signed-off-by:Thierry Reding <treding@nvidia.com> Acked-by:
Jose Abreu <joabreu@synopsys.com> Signed-off-by:
-
Xin Long authored
sctp_assoc_update_frag_point() should be called whenever asoc->pathmtu changes, but we missed one place in sctp_association_init(). It would cause frag_point is zero when sending data. As says in Jakub's reproducer, if sp->pathmtu is set by socketopt, the new asoc->pathmtu inherits it in sctp_association_init(). Later when transports are added and their pmtu >= asoc->pathmtu, it will never call sctp_assoc_update_frag_point() to set frag_point. This patch is to fix it by updating frag_point after asoc->pathmtu is set as sp->pathmtu in sctp_association_init(). Note that it moved them after sctp_stream_init(), as stream->si needs to be set first. Frag_point's calculation is also related with datachunk's type, so it needs to update frag_point when stream->si may be changed in sctp_process_init(). v1->v2: - call sctp_assoc_update_frag_point() separately in sctp_process_init and sctp_association_init, per Marcelo's suggestion. Fixes: 2f5e3c9d ("sctp: introduce sctp_assoc_update_frag_point") Reported-by:Jakub Audykowicz <jakub.audykowicz@gmail.com> Signed-off-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
-
Christoph Paasch authored
__qdisc_drop_all() accesses skb->prev to get to the tail of the segment-list. With commit 68d2f84a ("net: gro: properly remove skb from list") the skb-list handling has been changed to set skb->next to NULL and set the list-poison on skb->prev. With that change, __qdisc_drop_all() will panic when it tries to dereference skb->prev. Since commit 992cba7e ("net: Add and use skb_list_del_init().") __list_del_entry is used, leaving skb->prev unchanged (thus, pointing to the list-head if it's the first skb of the list). This will make __qdisc_drop_all modify the next-pointer of the list-head and result in a panic later on: [ 34.501053] general protection fault: 0000 [#1] SMP KASAN PTI [ 34.501968] CPU: 2 PID: 0 Comm: swapper/2 Not tainted 4.20.0-rc2.mptcp #108 [ 34.502887] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 0.5.1 01/01/2011 [ 34.504074] RIP: 0010:dev_gro_receive+0x343/0x1f90 [ 34.504751] Code: e0 48 c1 e8 03 42 80 3c 30 00 0f 85 4a 1c 00 00 4d 8b 24 24 4c 39 65 d0 0f 84 0a 04 00 00 49 8d 7c 24 38 48 89 f8 48 c1 e8 03 <42> 0f b6 04 30 84 c0 74 08 3c 04 [ 34.507060] RSP: 0018:ffff8883af507930 EFLAGS: 00010202 [ 34.507761] RAX: 0000000000000007 RBX: ffff8883970b2c80 RCX: 1ffff11072e165a6 [ 34.508640] RDX: 1ffff11075867008 RSI: ffff8883ac338040 RDI: 0000000000000038 [ 34.509493] RBP: ffff8883af5079d0 R08: ffff8883970b2d40 R09: 0000000000000062 [ 34.510346] R10: 0000000000000034 R11: 0000000000000000 R12: 0000000000000000 [ 34.511215] R13: 0000000000000000 R14: dffffc0000000000 R15: ffff8883ac338008 [ 34.512082] FS: 0000000000000000(0000) GS:ffff8883af500000(0000) knlGS:0000000000000000 [ 34.513036] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 34.513741] CR2: 000055ccc3e9d020 CR3: 00000003abf32000 CR4: 00000000000006e0 [ 34.514593] Call Trace: [ 34.514893] <IRQ> [ 34.515157] napi_gro_receive+0x93/0x150 [ 34.515632] receive_buf+0x893/0x3700 [ 34.516094] ? __netif_receive_skb+0x1f/0x1a0 [ 34.516629] ? virtnet_probe+0x1b40/0x1b40 [ 34.517153] ? __stable_node_chain+0x4d0/0x850 [ 34.517684] ? kfree+0x9a/0x180 [ 34.518067] ? __kasan_slab_free+0x171/0x190 [ 34.518582] ? detach_buf+0x1df/0x650 [ 34.519061] ? lapic_next_event+0x5a/0x90 [ 34.519539] ? virtqueue_get_buf_ctx+0x280/0x7f0 [ 34.520093] virtnet_poll+0x2df/0xd60 [ 34.520533] ? receive_buf+0x3700/0x3700 [ 34.521027] ? qdisc_watchdog_schedule_ns+0xd5/0x140 [ 34.521631] ? htb_dequeue+0x1817/0x25f0 [ 34.522107] ? sch_direct_xmit+0x142/0xf30 [ 34.522595] ? virtqueue_napi_schedule+0x26/0x30 [ 34.523155] net_rx_action+0x2f6/0xc50 [ 34.523601] ? napi_complete_done+0x2f0/0x2f0 [ 34.524126] ? kasan_check_read+0x11/0x20 [ 34.524608] ? _raw_spin_lock+0x7d/0xd0 [ 34.525070] ? _raw_spin_lock_bh+0xd0/0xd0 [ 34.525563] ? kvm_guest_apic_eoi_write+0x6b/0x80 [ 34.526130] ? apic_ack_irq+0x9e/0xe0 [ 34.526567] __do_softirq+0x188/0x4b5 [ 34.527015] irq_exit+0x151/0x180 [ 34.527417] do_IRQ+0xdb/0x150 [ 34.527783] common_interrupt+0xf/0xf [ 34.528223] </IRQ> This patch makes sure that skb->prev is set to NULL when entering netem_enqueue. Cc: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp> Cc: Tyler Hicks <tyhicks@canonical.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Fixes: 68d2f84a ("net: gro: properly remove skb from list") Suggested-by:
Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
Christoph Paasch <cpaasch@apple.com> Reviewed-by:
-
- 29 Nov, 2018 12 commits
-
-
Martin Schiller authored
If a session in X25_STATE_1 (Awaiting Call Accept) receives a call request, the session will be closed (x25_disconnect), cause=0x01 (Number Busy) and diag=0x48 (Call Collision) will be set and a clear request will be send. Signed-off-by:
Martin Schiller <ms@dev.tdt.de> Signed-off-by:
-
Martin Schiller authored
o x25_find_listener(): the compare for the null_x25_address was wrong. We have to check the x25_addr of the listener socket instead of the x25_addr of the incomming call. o x25_bind(): it was not possible to bind a socket to null_x25_address Signed-off-by:
-
Martin Schiller authored
The length of the called and calling address was not calculated correctly (BCD encoding). Signed-off-by:
-
Baruch Siach authored
SFP standards are now available from the SNIA (Storage Networking Industry Association) website. Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
Baruch Siach <baruch@tkos.co.il> Reviewed-by:
-
David S. Miller authored
Sabrina Dubroca says: ==================== fixes for XPS configuration after Symmetric queue selection This fixes some bugs introduced by the "Symmetric queue selection using XPS for Rx queues". First, the refactoring of the cleanup function skipped resetting the queue's NUMA node under some conditions. Second, the accounting on static keys for XPS and RXQS-XPS is unbalanced, so the static key for XPS won't actually disable itself, once enabled. The RXQS-XPS static key can actually be disabled by reconfiguring a device that didn't have RXQS-XPS configured at all. ==================== Signed-off-by: -
Sabrina Dubroca authored
Commit 04157469 ("net: Use static_key for XPS maps") introduced a static key for XPS, but the increments/decrements don't match. First, the static key's counter is incremented once for each queue, but only decremented once for a whole batch of queues, leading to large unbalances. Second, the xps_rxqs_needed key is decremented whenever we reset a batch of queues, whether they had any rxqs mapping or not, so that if we setup cpu-XPS on em1 and RXQS-XPS on em2, resetting the queues on em1 would decrement the xps_rxqs_needed key. This reworks the accounting scheme so that the xps_needed key is incremented only once for each type of XPS for all the queues on a device, and the xps_rxqs_needed key is incremented only once for all queues. This is sufficient to let us retrieve queues via get_xps_queue(). This patch introduces a new reset_xps_maps(), which reinitializes and frees the appropriate map (xps_rxqs_map or xps_cpus_map), and drops a reference to the needed keys: - both xps_needed and xps_rxqs_needed, in case of rxqs maps, - only xps_needed, in case of CPU maps. Now, we also need to call reset_xps_maps() at the end of __netif_set_xps_queue() when there's no active map left, for example when writing '00000000,00000000' to all queues' xps_rxqs setting. Fixes: 04157469 ("net: Use static_key for XPS maps") Signed-off-by:
Sabrina Dubroca <sd@queasysnail.net> Signed-off-by:
-
Sabrina Dubroca authored
Before commit 80d19669 ("net: Refactor XPS for CPUs and Rx queues"), netif_reset_xps_queues() did netdev_queue_numa_node_write() for all the queues being reset. Now, this is only done when the "active" variable in clean_xps_maps() is false, ie when on all the CPUs, there's no active XPS mapping left. Fixes: 80d19669 ("net: Refactor XPS for CPUs and Rx queues") Signed-off-by:
-
Baruch Siach authored
The link modes that sfp_parse_support() detects are stored in the 'modes' bitmap. There is no reason to make an exception for 1000Base-PX or 1000Base-BX10. Fixes: 03145864 ("sfp: support 1G BiDi (eg, FiberStore SFP-GE-BX) modules") Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
-
David S. Miller authored
Kunihiko Hayashi says: ==================== fixup AVE ethernet driver This series adds fixup for AVE ethernet driver that includes increse of descriptors, replacing macro for linux-next, and adding missing author information. ==================== Signed-off-by: -
Kunihiko Hayashi authored
Add missing MODULE_AUTHOR of ave driver and an entry to MAINTAINERS. Signed-off-by:
Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Signed-off-by:
-
Kunihiko Hayashi authored
In commit 26a4676f ("arm64: mm: define NET_IP_ALIGN to 0"), AVE controller affects this modification because the controller forces to ignore lower 2bits of buffer start address, and make 2-byte headroom, that is, data reception starts from (buffer + 2). This patch defines AVE_FRAME_HEADROOM macro as hardware-specific value, and replaces NET_IP_ALIGN with it. Signed-off-by:
-
Kunihiko Hayashi authored
To improve performance, this increases Rx descriptor to 256, Tx descriptor to 64, and adjusts NAPI weight to NAPI_POLL_WEIGHT. Signed-off-by:
-
- 28 Nov, 2018 3 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) ARM64 JIT fixes for subprog handling from Daniel Borkmann. 2) Various sparc64 JIT bug fixes (fused branch convergance, frame pointer usage detection logic, PSEODU call argument handling). 3) Fix to use BH locking in nf_conncount, from Taehee Yoo. 4) Fix race of TX skb freeing in ipheth driver, from Bernd Eckstein. 5) Handle return value of TX NAPI completion properly in lan743x driver, from Bryan Whitehead. 6) MAC filter deletion in i40e driver clears wrong state bit, from Lihong Yang. 7) Fix use after free in rionet driver, from Pan Bian. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (53 commits) s390/qeth: fix length check in SNMP processing net: hisilicon: remove unexpected free_netdev rapidio/rionet: do not free skb before reading its length i40e: fix kerneldoc for xsk methods ixgbe: recognize 1000BaseLX SFP modules as 1Gbps i40e: Fix deletion of MAC filters igb: fix uninitialized variables netfilter: nf_tables: deactivate expressions in rule replecement routine lan743x: Enable driver to work with LAN7431 tipc: fix lockdep warning during node delete lan743x: fix return value for lan743x_tx_napi_poll net: via: via-velocity: fix spelling mistake "alignement" -> "alignment" qed: fix spelling mistake "attnetion" -> "attention" net: thunderx: fix NULL pointer dereference in nic_remove sctp: increase sk_wmem_alloc when head->truesize is increased firestream: fix spelling mistake: "Inititing" -> "Initializing" net: phy: add workaround for issue where PHY driver doesn't bind to the device usbnet: ipheth: fix potential recvmsg bug and recvmsg bug 2 sparc: Adjust bpf JIT prologue for PSEUDO calls. bpf, doc: add entries of who looks over which jits ... -
git://github.com/jcmvbkbc/linux-xtensaLinus Torvalds authored
Pull Xtensa fixes from Max Filippov: - fix kernel exception on userspace access to a currently disabled coprocessor - fix coprocessor data saving/restoring in configurations with multiple coprocessors - fix ptrace access to coprocessor data on configurations with multiple coprocessors with high alignment requirements * tag 'xtensa-20181128' of git://github.com/jcmvbkbc/linux-xtensa: xtensa: fix coprocessor part of ptrace_{get,set}xregs xtensa: fix coprocessor context offset definitions xtensa: enable coprocessors that are being flushed
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queueDavid S. Miller authored
Jeff Kirsher says: ==================== Intel Wired LAN Driver Fixes 2018-11-28 This series contains fixes to igb, ixgbe and i40e. Yunjian Wang from Huawei resolves a variable that could potentially be NULL before it is used. Lihong fixes an i40e issue which goes back to 4.17 kernels, where deleting any of the MAC filters was causing the incorrect syncing for the PF. Josh Elsasser caught that there were missing enum values in the link capabilities for x550 devices, which was preventing link for 1000BaseLX SFP modules. Jan fixes the function header comments for XSK methods. ==================== Signed-off-by:
-
