bpf_skb_store_bytes() invocations above L2 header need BPF_F_RECOMPUTE_CSUM
flag for updates, so that CHECKSUM_COMPLETE will be fixed up along the way.
Where we ran into an issue with bpf_skb_store_bytes() is when we did a
single-byte update on the IPv6 hoplimit despite using BPF_F_RECOMPUTE_CSUM
flag; simple ping via ICMPv6 triggered a hw csum failure as a result. The
underlying issue has been tracked down to a buffer alignment issue.

Meaning, that csum_partial() computations via skb_postpull_rcsum() and
skb_postpush_rcsum() pair invoked had a wrong result since they operated on
an odd address for the hoplimit, while other computations were done on an
even address. This mix doesn't work as-is with skb_postpull_rcsum(),
skb_postpush_rcsum() pair as it always expects at least half-word alignment
of input buffers, which is normally the case. Thus, instead of these helpers
using csum_sub() and (implicitly) csum_add(), we need to use csum_block_sub(),
csum_block_add(), respectively. For unaligned offsets, they rotate the sum
to align it to a half-word boundary again, otherwise they work the same as
csum_sub() and csum_add().

Adding __skb_postpull_rcsum(), __skb_postpush_rcsum() variants that take the
offset as an input and adapting bpf_skb_store_bytes() to them fixes the hw
csum failures again. The skb_postpull_rcsum(), skb_postpush_rcsum() helpers
use a 0 constant for offset so that the compiler optimizes the offset & 1
test away and generates the same code as with csum_sub()/_add().

Fixes: 608cd71a ("tc: bpf: generalize pedit action")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Follow-up to commit f8ffad69 ("bpf: add skb_postpush_rcsum and fix
dev_forward_skb occasions") to fix an issue for dev_queue_xmit() redirect
locations which need CHECKSUM_COMPLETE fixups on ingress.

For the same reasons as described in f8ffad69 already, we of course
also need this here, since dev_queue_xmit() on a veth device will let us
end up in the dev_forward_skb() helper again to cross namespaces.

Latter then calls into skb_postpull_rcsum() to pull out L2 header, so
that netif_rx_internal() sees CHECKSUM_COMPLETE as it is expected. That
is, CHECKSUM_COMPLETE on ingress covering L2 _payload_, not L2 headers.

Also here we have to address bpf_redirect() and bpf_clone_redirect().

Fixes: 3896d655 ("bpf: introduce bpf_clone_redirect() helper")
Fixes: 27b29f63 ("bpf: add bpf_redirect() helper")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The call site for this function appears as:

  #ifdef DEBUG
        data->msg_enable = DEBUG;
        dump_eth_one(dev);
  #endif

...leading to the following warning for !DEBUG builds:

drivers/net/ethernet/tundra/tsi108_eth.c:169:13: warning: 'dump_eth_one' defined but not used [-Wunused-function]
 static void dump_eth_one(struct net_device *dev)
             ^

...when using the arch/powerpc/configs/mpc7448_hpc2_defconfig

Put the function definition under the same #ifdef as the call site
to avoid the warning.

Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: DCB fixes

Patches 1 and 2 fix a problem in which PAUSE frames settings are wrongly
overridden when ieee_setpfc() gets called.

Patch 3 adds a missing rollback in port's creation error path.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We correctly execute mlxsw_sp_port_dcb_fini() when port is removed, but
I missed its rollback in the error path of port creation, so add it.

Fixes: f00817df ("mlxsw: spectrum: Introduce support for Data Center Bridging (DCB)")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PFCC register is used to configure both PAUSE and PFC frames.
Therefore, when PFC frames are disabled we must make sure we don't
mistakenly also disable PAUSE frames (which might be enabled).

Fix this by packing the PFCC register with the current PAUSE settings.

Note that this register is also accessed via ethtool ops, but there we
are guaranteed to have PFC disabled.

Fixes: d81a6bdb ("mlxsw: spectrum: Add IEEE 802.1Qbb PFC support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When ieee_setpfc() gets called, PAUSE frames are not necessarily
disabled on the port.

Check if PAUSE frames are disabled or enabled and configure the port's
headroom buffer accordingly.

Fixes: d81a6bdb ("mlxsw: spectrum: Add IEEE 802.1Qbb PFC support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Looks like a simple copy'n'paste error.

Fixes: 1aa661f5 ("rhashtable-test: Measure time to insert, remove & traverse entries")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

Phil Sutter says:

====================
sctp_diag: A bunch of fixes for upcoming 'ss' support

The following series contains a number of fixes necessary to make my yet
unpublished 'ss' support patch functional.

Changes since v1:
- Fixed patch 2/3
- Rebased whole series onto current net-next/master

Changes since v2:
- Improved description of patch 2/3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Since 'ss' always adds TCPF_CLOSE to idiag_states flags, sctp_diag can't
rely upon TCPF_LISTEN flag solely being present when listening sockets
are requested.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

The asoc's timer value is not kept in asoc->timeouts array but in it's
primary transport instead.

Furthermore, we must export the timer only if it is pending, otherwise
the value will underrun when stored in an unsigned variable and
user space will only see a very large timeout value.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is required to correctly interpret INET_DIAG_INFO messages exported
by sctp_diag module.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

USRIO and JUMBO CAPS have the same mask.
Fix the same.

Fixes: ce721a70 ("net: ethernet: cadence-macb: Add disabled usrio caps")
Cc: stable@vger.kernel.org # v4.5+
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2016-08-05' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
First set of fixes for the current cycle:
 * fix 80+80 bandwidth warning
 * fix powersave with mac80211 TXQ implementation
 * use correct way to free SKBs from multicast buffering
 * mesh: fix operation ordering to work with all drivers
 * mesh: end service period even when peer goes away
 * mesh: correct HT opmode validity checks
 * pass hw pointer from mac80211 to driver in TPT method,
   fixing a bug (in a bit the wrong way, but that's what
   we have right now)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

increase test coverage to check previously missing 'update when full'
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The introduction of pre-allocated hash elements inadvertently broke
the behavior of bpf hash maps where users expected to call
bpf_map_update_elem() without considering that the map can be full.
Some programs do:
old_value = bpf_map_lookup_elem(map, key);
if (old_value) {
  ... prepare new_value on stack ...
  bpf_map_update_elem(map, key, new_value);
}
Before pre-alloc the update() for existing element would work even
in 'map full' condition. Restore this behavior.

The above program could have updated old_value in place instead of
update() which would be faster and most programs use that approach,
but sometimes the values are large and the programs use update()
helper to do atomic replacement of the element.
Note we cannot simply update element's value in-place like percpu
hash map does and have to allocate extra num_possible_cpu elements
and use this extra reserve when the map is full.

Fixes: 6c905981 ("bpf: pre-allocate hash map elements")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

On 32-bit (e.g. with m68k-linux-gnu-gcc-4.1):

    drivers/net/dsa/b53/b53_common.c: In function ‘b53_arl_read’:
    drivers/net/dsa/b53/b53_common.c:1072: warning: integer constant is too large for ‘long’ type

Fixes: 1da6df85 ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Panic occurs when issuing "cat /proc/net/route" whilst
populating FIB with > 1M routes.

Use of cached node pointer in fib_route_get_idx is unsafe.

 BUG: unable to handle kernel paging request at ffffc90001630024
 IP: [<ffffffff814cf6a0>] leaf_walk_rcu+0x10/0xe0
 PGD 11b08d067 PUD 11b08e067 PMD dac4b067 PTE 0
 Oops: 0000 [#1] SMP
 Modules linked in: nfsd auth_rpcgss oid_registry nfs_acl nfs lockd grace fscac
 snd_hda_codec_generic snd_hda_intel snd_hda_codec snd_hda_core snd_hwdep virti
 acpi_cpufreq button parport_pc ppdev lp parport autofs4 ext4 crc16 mbcache jbd
tio_ring virtio floppy uhci_hcd ehci_hcd usbcore usb_common libata scsi_mod
 CPU: 1 PID: 785 Comm: cat Not tainted 4.2.0-rc8+ #4
 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
 task: ffff8800da1c0bc0 ti: ffff88011a05c000 task.ti: ffff88011a05c000
 RIP: 0010:[<ffffffff814cf6a0>]  [<ffffffff814cf6a0>] leaf_walk_rcu+0x10/0xe0
 RSP: 0018:ffff88011a05fda0  EFLAGS: 00010202
 RAX: ffff8800d8a40c00 RBX: ffff8800da4af940 RCX: ffff88011a05ff20
 RDX: ffffc90001630020 RSI: 0000000001013531 RDI: ffff8800da4af950
 RBP: 0000000000000000 R08: ffff8800da1f9a00 R09: 0000000000000000
 R10: ffff8800db45b7e4 R11: 0000000000000246 R12: ffff8800da4af950
 R13: ffff8800d97a74c0 R14: 0000000000000000 R15: ffff8800d97a7480
 FS:  00007fd3970e0700(0000) GS:ffff88011fd00000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
 CR2: ffffc90001630024 CR3: 000000011a7e4000 CR4: 00000000000006e0
 Stack:
  ffffffff814d00d3 0000000000000000 ffff88011a05ff20 ffff8800da1f9a00
  ffffffff811dd8b9 0000000000000800 0000000000020000 00007fd396f35000
  ffffffff811f8714 0000000000003431 ffffffff8138dce0 0000000000000f80
 Call Trace:
  [<ffffffff814d00d3>] ? fib_route_seq_start+0x93/0xc0
  [<ffffffff811dd8b9>] ? seq_read+0x149/0x380
  [<ffffffff811f8714>] ? fsnotify+0x3b4/0x500
  [<ffffffff8138dce0>] ? process_echoes+0x70/0x70
  [<ffffffff8121cfa7>] ? proc_reg_read+0x47/0x70
  [<ffffffff811bb823>] ? __vfs_read+0x23/0xd0
  [<ffffffff811bbd42>] ? rw_verify_area+0x52/0xf0
  [<ffffffff811bbe61>] ? vfs_read+0x81/0x120
  [<ffffffff811bcbc2>] ? SyS_read+0x42/0xa0
  [<ffffffff81549ab2>] ? entry_SYSCALL_64_fastpath+0x16/0x75
 Code: 48 85 c0 75 d8 f3 c3 31 c0 c3 f3 c3 66 66 66 66 66 66 2e 0f 1f 84 00 00
a 04 89 f0 33 02 44 89 c9 48 d3 e8 0f b6 4a 05 49 89
 RIP  [<ffffffff814cf6a0>] leaf_walk_rcu+0x10/0xe0
  RSP <ffff88011a05fda0>
 CR2: ffffc90001630024
Signed-off-by: Dave Forster <dforster@brocade.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Inside the kafs filesystem it is possible to occasionally have a call
processed and terminated before we've had a chance to check whether we need
to clean up the rx queue for that call because afs_send_simple_reply() ends
the call when it is done, but this is done in a workqueue item that might
happen to run to completion before afs_deliver_to_call() completes.

Further, it is possible for rxrpc_kernel_send_data() to be called to send a
reply before the last request-phase data skb is released.  The rxrpc skb
destructor is where the ACK processing is done and the call state is
advanced upon release of the last skb.  ACK generation is also deferred to
a work item because it's possible that the skb destructor is not called in
a context where kernel_sendmsg() can be invoked.

To this end, the following changes are made:

 (1) kernel_rxrpc_data_consumed() is added.  This should be called whenever
     an skb is emptied so as to crank the ACK and call states.  This does
     not release the skb, however.  kernel_rxrpc_free_skb() must now be
     called to achieve that.  These together replace
     rxrpc_kernel_data_delivered().

 (2) kernel_rxrpc_data_consumed() is wrapped by afs_data_consumed().

     This makes afs_deliver_to_call() easier to work as the skb can simply
     be discarded unconditionally here without trying to work out what the
     return value of the ->deliver() function means.

     The ->deliver() functions can, via afs_data_complete(),
     afs_transfer_reply() and afs_extract_data() mark that an skb has been
     consumed (thereby cranking the state) without the need to
     conditionally free the skb to make sure the state is correct on an
     incoming call for when the call processor tries to send the reply.

 (3) rxrpc_recvmsg() now has to call kernel_rxrpc_data_consumed() when it
     has finished with a packet and MSG_PEEK isn't set.

 (4) rxrpc_packet_destructor() no longer calls rxrpc_hard_ACK_data().

     Because of this, we no longer need to clear the destructor and put the
     call before we free the skb in cases where we don't want the ACK/call
     state to be cranked.

 (5) The ->deliver() call-type callbacks are made to return -EAGAIN rather
     than 0 if they expect more data (afs_extract_data() returns -EAGAIN to
     the delivery function already), and the caller is now responsible for
     producing an abort if that was the last packet.

 (6) There are many bits of unmarshalling code where:

 		ret = afs_extract_data(call, skb, last, ...);
		switch (ret) {
		case 0:		break;
		case -EAGAIN:	return 0;
		default:	return ret;
		}

     is to be found.  As -EAGAIN can now be passed back to the caller, we
     now just return if ret < 0:

 		ret = afs_extract_data(call, skb, last, ...);
		if (ret < 0)
			return ret;

 (7) Checks for trailing data and empty final data packets has been
     consolidated as afs_data_complete().  So:

		if (skb->len > 0)
			return -EBADMSG;
		if (!last)
			return 0;

     becomes:

		ret = afs_data_complete(call, skb, last);
		if (ret < 0)
			return ret;

 (8) afs_transfer_reply() now checks the amount of data it has against the
     amount of data desired and the amount of data in the skb and returns
     an error to induce an abort if we don't get exactly what we want.

Without these changes, the following oops can occasionally be observed,
particularly if some printks are inserted into the delivery path:

general protection fault: 0000 [#1] SMP
Modules linked in: kafs(E) af_rxrpc(E) [last unloaded: af_rxrpc]
CPU: 0 PID: 1305 Comm: kworker/u8:3 Tainted: G            E   4.7.0-fsdevel+ #1303
Hardware name: ASUS All Series/H97-PLUS, BIOS 2306 10/09/2014
Workqueue: kafsd afs_async_workfn [kafs]
task: ffff88040be041c0 ti: ffff88040c070000 task.ti: ffff88040c070000
RIP: 0010:[<ffffffff8108fd3c>]  [<ffffffff8108fd3c>] __lock_acquire+0xcf/0x15a1
RSP: 0018:ffff88040c073bc0  EFLAGS: 00010002
RAX: 6b6b6b6b6b6b6b6b RBX: 0000000000000000 RCX: ffff88040d29a710
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff88040d29a710
RBP: ffff88040c073c70 R08: 0000000000000001 R09: 0000000000000001
R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000000 R14: ffff88040be041c0 R15: ffffffff814c928f
FS:  0000000000000000(0000) GS:ffff88041fa00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fa4595f4750 CR3: 0000000001c14000 CR4: 00000000001406f0
Stack:
 0000000000000006 000000000be04930 0000000000000000 ffff880400000000
 ffff880400000000 ffffffff8108f847 ffff88040be041c0 ffffffff81050446
 ffff8803fc08a920 ffff8803fc08a958 ffff88040be041c0 ffff88040c073c38
Call Trace:
 [<ffffffff8108f847>] ? mark_held_locks+0x5e/0x74
 [<ffffffff81050446>] ? __local_bh_enable_ip+0x9b/0xa1
 [<ffffffff8108f9ca>] ? trace_hardirqs_on_caller+0x16d/0x189
 [<ffffffff810915f4>] lock_acquire+0x122/0x1b6
 [<ffffffff810915f4>] ? lock_acquire+0x122/0x1b6
 [<ffffffff814c928f>] ? skb_dequeue+0x18/0x61
 [<ffffffff81609dbf>] _raw_spin_lock_irqsave+0x35/0x49
 [<ffffffff814c928f>] ? skb_dequeue+0x18/0x61
 [<ffffffff814c928f>] skb_dequeue+0x18/0x61
 [<ffffffffa009aa92>] afs_deliver_to_call+0x344/0x39d [kafs]
 [<ffffffffa009ab37>] afs_process_async_call+0x4c/0xd5 [kafs]
 [<ffffffffa0099e9c>] afs_async_workfn+0xe/0x10 [kafs]
 [<ffffffff81063a3a>] process_one_work+0x29d/0x57c
 [<ffffffff81064ac2>] worker_thread+0x24a/0x385
 [<ffffffff81064878>] ? rescuer_thread+0x2d0/0x2d0
 [<ffffffff810696f5>] kthread+0xf3/0xfb
 [<ffffffff8160a6ff>] ret_from_fork+0x1f/0x40
 [<ffffffff81069602>] ? kthread_create_on_node+0x1cf/0x1cf
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit a94efbd7 ("ethernet: arc: emac_main: add missing of_node_put
after calling of_parse_phandle") added missing of_node_put after calling
of_parse_phandle, but missing the devm_ioremap_resource() error handling
case.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net_device->ndo_set_rx_headroom (introduced in
871b642a) says

  "Setting a negtaive value reset the rx headroom
   to the default value".

It seems that the OVS implementation in
3a927bc7 overlooked this and sets
dev->needed_headroom unconditionally.

This doesn't have an immediate effect, but can mess up later
LL_RESERVED_SPACE calculations, such as done in
net/ipv6/mcast.c:mld_newpack.  For reference, this issue was found
from a skb_panic raised there after the length calculations had given
the wrong result.

Note the other current users of this interface
(drivers/net/tun.c:tun_set_headroom and
drivers/net/veth.c:veth_set_rx_headroom) are both checking this
correctly thus need no modification.

Thanks to Ben for some pointers from the crash dumps!

Cc: Benjamin Poirier <bpoirier@suse.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1361414Signed-off-by: Ian Wienand <iwienand@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The variable is added to allow the driver an easy access to
it's own hw->priv when the op is invoked.

This fixes a crash in wlcore because it was relying on a
station pointer that wasn't initialized yet. It's the wrong
way to fix the crash, but it solves the problem for now and
it does make sense to have the hw pointer here.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
[rewrite commit message, fix indentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Previously, NL80211_MESHCONF_HT_OPMODE validation rejected correct
flag combinations, e.g. IEEE80211_HT_OP_MODE_PROTECTION_NONHT_MIXED |
IEEE80211_HT_OP_MODE_NON_HT_STA_PRSNT.

Doing just a range-check allows setting flags that don't exist (0x8)
and invalid flag combinations.

Implements some checks based on IEEE 802.11 2012 8.4.2.59 "HT
Operation element".
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
[reword commit message, simplify a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If QoS frame with EOSP (end of service period) subfield=1 sent by local
peer was not acked by remote peer, local peer did not end the MPSP. This
prevents local peer from going to DOZE state. And if the remote peer
goes away without closing connection, local peer continues AWAKE state
and wastes battery.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The code currently assumes that buffered multicast PS frames don't have
a pending ACK frame for tx status reporting.
However, hostapd sends a broadcast deauth frame on teardown for which tx
status is requested. This can lead to the "Have pending ack frames"
warning on module reload.
Fix this by using ieee80211_free_txskb/ieee80211_purge_tx_queue.

Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Manish Chopra says:

====================
qlcnic: bug fixes

This series fixes a data structure corruption bug in
VF's async mailbox commands handling and an issue realted
to napi poll budget in the driver.

Please consider applying this series to "net"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver modifies the supplied NAPI budget in qlcnic_83xx_msix_tx_poll()
function. Instead, it should use the budget as it is.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a data structure corruption bug in the SRIOV VF mailbox
handler code. While handling mailbox commands from the atomic context,
driver is accessing and updating qlcnic_async_work_list_struct entry fields
in the async work list. These fields could be concurrently accessed by the
work function resulting in data corruption.

This patch restructures async mbx command handling by using a separate
async command list instead of using a list of work_struct structures.
A single work_struct is used to schedule and handle the async commands
with proper locking mechanism.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Siva Reddy Kallam says:

====================
tg3: Disallow 0 rx coalesce time and correctly report RSS queues in tg3_get_rxnfc

First patch:
        Diasllow rx coalescing time to be 0

Second patch:
        Report the correct number of RSS queues through tg3_get_rxnfc
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch remove the wrong substraction from info->data in
tg3_get_rxnfc function. Without this patch, the number of RSS
queues reported is less by one.
Reported-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the rx coalescing time is 0, interrupts
are not generated from the controller and rx path hangs.
To avoid this rx hang, updating the driver to not allow
rx coalescing time to be 0.
Signed-off-by: Satish Baddipadige <satish.baddipadige@broadcom.com>
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Using per-register incrementing ID can lead to
find_good_pkt_pointers() confusing registers which
have completely different values.  Consider example:

0: (bf) r6 = r1
1: (61) r8 = *(u32 *)(r6 +76)
2: (61) r0 = *(u32 *)(r6 +80)
3: (bf) r7 = r8
4: (07) r8 += 32
5: (2d) if r8 > r0 goto pc+9
 R0=pkt_end R1=ctx R6=ctx R7=pkt(id=0,off=0,r=32) R8=pkt(id=0,off=32,r=32) R10=fp
6: (bf) r8 = r7
7: (bf) r9 = r7
8: (71) r1 = *(u8 *)(r7 +0)
9: (0f) r8 += r1
10: (71) r1 = *(u8 *)(r7 +1)
11: (0f) r9 += r1
12: (07) r8 += 32
13: (2d) if r8 > r0 goto pc+1
 R0=pkt_end R1=inv56 R6=ctx R7=pkt(id=0,off=0,r=32) R8=pkt(id=1,off=32,r=32) R9=pkt(id=1,off=0,r=32) R10=fp
14: (71) r1 = *(u8 *)(r9 +16)
15: (b7) r7 = 0
16: (bf) r0 = r7
17: (95) exit

We need to get a UNKNOWN_VALUE with imm to force id
generation so lines 0-5 make r7 a valid packet pointer.
We then read two different bytes from the packet and
add them to copies of the constructed packet pointer.
r8 (line 9) and r9 (line 11) will get the same id of 1,
independently.  When either of them is validated (line
13) - find_good_pkt_pointers() will also mark the other
as safe.  This leads to access on line 14 being mistakenly
considered safe.

Fixes: 969bf05e ("bpf: direct packet access")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Building with -Wmaybe-uninitialized shows a potential use of
an uninitialized variable:

drivers/net/ethernet/apm/xgene/xgene_enet_hw.c: In function 'xgene_enet_phy_connect':
drivers/net/ethernet/apm/xgene/xgene_enet_hw.c:802:23: warning: 'phy_dev' may be used uninitialized in this function [-Wmaybe-uninitialized]

Although the compiler correctly identified this based on the function,
the current code is still safe as long dev->of_node is non-NULL
for the case of CONFIG_ACPI=n, which is currently the case.

The warning is now disabled by default, but still appears when
building with W=1, and other build test tools should be able to
detect it as well. Adding an #else clause here makes the code
more robust and makes it clear to the compiler that this cannot
happen.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 8089a96f ("drivers: net: xgene: Add backward compatibility")
Signed-off-by: David S. Miller <davem@davemloft.net>

ovs_ct_find_existing() issues a warning if an existing conntrack entry
classified as IP_CT_NEW is found, with the premise that this should
not happen.  However, a newly confirmed, non-expected conntrack entry
remains IP_CT_NEW as long as no reply direction traffic is seen.  This
has resulted into somewhat confusing kernel log messages.  This patch
removes this check and warning.

Fixes: 289f2253 ("openvswitch: Find existing conntrack entry after upcall.")
Suggested-by: Joe Stringer <joe@ovn.org>
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull tracing fixes from Steven Rostedt:
 "A few updates and fixes:

   - move the suppressing of the __builtin_return_address >0 warning to
     the tracing directory only.

   - metag recordmcount fix for newer glibc's

   - two tracing histogram fixes that were reported by KASAN"

* tag 'trace-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Fix use-after-free in hist_register_trigger()
  tracing: Fix use-after-free in hist_unreg_all/hist_enable_unreg_all
  Makefile: Mute warning for __builtin_return_address(>0) for tracing only
  ftrace/recordmcount: Work around for addition of metag magic but not relocations

With gcc < 4.2 (e.g. 4.1.2):

      CC      fs/proc/task_mmu.o
    cc1: error: unrecognized command line option "-Wno-override-init"

To fix this, only enable the compiler option when it is actually
supported by the compiler.

Fixes: ca52953f ("fs/proc/task_mmu.c: suppress compilation warnings with W=1")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull networking fixes from David Miller:

 1) Fix several cases of missing of_node_put() calls in various
    networking drivers.  From Peter Chen.

 2) Don't try to remove unconfigured VLANs in qed driver, from Yuval
    Mintz.

 3) Unbalanced locking in TIPC error handling, from Wei Yongjun.

 4) Fix lockups in CPDMA driver, from Grygorii Strashko.

 5) More MACSEC refcount et al fixes, from Sabrina Dubroca.

 6) Fix MAC address setting in r8169 during runtime suspend, from
    Chun-Hao Lin.

 7) Various printf format specifier fixes, from Heinrich Schuchardt.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (59 commits)
  qed: Fail driver load in 100g MSI mode.
  ethernet: ti: davinci_emac: add missing of_node_put after calling of_parse_phandle
  ethernet: stmicro: stmmac: add missing of_node_put after calling of_parse_phandle
  ethernet: stmicro: stmmac: dwmac-socfpga: add missing of_node_put after calling of_parse_phandle
  ethernet: renesas: sh_eth: add missing of_node_put after calling of_parse_phandle
  ethernet: renesas: ravb_main: add missing of_node_put after calling of_parse_phandle
  ethernet: marvell: pxa168_eth: add missing of_node_put after calling of_parse_phandle
  ethernet: marvell: mvpp2: add missing of_node_put after calling of_parse_phandle
  ethernet: marvell: mvneta: add missing of_node_put after calling of_parse_phandle
  ethernet: hisilicon: hns: hns_dsaf_main: add missing of_node_put after calling of_parse_phandle
  ethernet: hisilicon: hns: hns_dsaf_mac: add missing of_node_put after calling of_parse_phandle
  ethernet: cavium: octeon: add missing of_node_put after calling of_parse_phandle
  ethernet: aurora: nb8800: add missing of_node_put after calling of_parse_phandle
  ethernet: arc: emac_main: add missing of_node_put after calling of_parse_phandle
  ethernet: apm: xgene: add missing of_node_put after calling of_parse_phandle
  ethernet: altera: add missing of_node_put
  8139too: fix system hang when there is a tx timeout event.
  qed: Fix error return code in qed_resc_alloc()
  net: qlcnic: avoid superfluous assignement
  dsa: b53: remove redundant if
  ...

Some drivers (e.g. wl18xx) expect that the last stage in the
de-initialization process will be stopping the beacons, similar to AP flow.
Update ieee80211_stop_mesh() flow accordingly.
As peers can be removed dynamically, this would not impact other drivers.

Tested also on Ralink RT3572 chipset.
Signed-off-by: Maital Hahn <maitalm@ti.com>
Signed-off-by: Yaniv Machani <yanivma@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Merge yet more updates from Andrew Morton:

 - the rest of ocfs2

 - various hotfixes, mainly MM

 - quite a bit of misc stuff - drivers, fork, exec, signals, etc.

 - printk updates

 - firmware

 - checkpatch

 - nilfs2

 - more kexec stuff than usual

 - rapidio updates

 - w1 things

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (111 commits)
  ipc: delete "nr_ipc_ns"
  kcov: allow more fine-grained coverage instrumentation
  init/Kconfig: add clarification for out-of-tree modules
  config: add android config fragments
  init/Kconfig: ban CONFIG_LOCALVERSION_AUTO with allmodconfig
  relay: add global mode support for buffer-only channels
  init: allow blacklisting of module_init functions
  w1:omap_hdq: fix regression
  w1: add helper macro module_w1_family
  w1: remove need for ida and use PLATFORM_DEVID_AUTO
  rapidio/switches: add driver for IDT gen3 switches
  powerpc/fsl_rio: apply changes for RIO spec rev 3
  rapidio: modify for rev.3 specification changes
  rapidio: change inbound window size type to u64
  rapidio/idt_gen2: fix locking warning
  rapidio: fix error handling in mbox request/release functions
  rapidio/tsi721_dma: advance queue processing from transfer submit call
  rapidio/tsi721: add messaging mbox selector parameter
  rapidio/tsi721: add PCIe MRRS override parameter
  rapidio/tsi721_dma: add channel mask and queue size parameters
  ...