When an attempt is made to read the interface strings of the Artisman
Watchdog USB dongle (idVendor:idProduct 04b4:0526) an error is written
to the dmesg log (uhci_result_common: failed with status 440000) and the
dongle resets itself, resulting in a disconnect/reconnect loop.

Adding the dongle to the list of devices in quirks.c, with the same
quirk Alan Stern's previous patch for the Saitek Cyborg Gold 3D
joystick, stops the device from resetting and allows it to be used with
no problems.
Signed-off-by: Paul Mortier <mortier@btinternet.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

When a configured device is reset, the control endpoint's ring is reused.
If control transfers to the device were issued before the device is reset,
the dequeue pointer will be somewhere in the middle of the ring.  If the
device is then issued an address with the set address command, the xHCI
driver must provide a valid input context for control endpoint zero.

The original code would give the hardware the original input context,
which had a dequeue pointer set to the top of the ring.  This would cause
the host to re-execute any control transfers until it reached the ring's
enqueue pointer.  When issuing a set address command for a device that has
just been configured and then reset, use the control endpoint's enqueue
pointer as the hardware's dequeue pointer.

Assumption:  All control transfers will be completed or cancelled before
the set address command is issued to the device.  If there are any
outstanding control transfers, this code will not work.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Without this fix, a USB 3.0 port is downgraded to full speed after a port
reset of a configured device.  The USB 3.0 terminations will be disabled
permanently, and USB 3.0 devices will always enumerate as full speed
devices, until the host controller is unplugged (if it is an ExpressCard)
or the computer is rebooted.

Fajun Chen traced this traced the speed downgrade issue to the port reset
and the interpretation of port status in USB hub driver code.  The hub
code was not testing for the port being a SuperSpeed port, and it fell
through to the else case of Full Speed.

The following patch adds SuperSpeed mapping from the port status, and
fixes the speed downgrade issue.
Reported-by: Fajun Chen <fajun.chen@seagate.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Commit 6c12db90 also seems to have
introduced a bug that is triggered when the command ring is about to wrap.
The inc_enq() function will not have moved the enqueue pointer past the
link TRB.  It is supposed to be moved past the link TRB in prepare_ring(),
which should be called before a TD is enqueued.  However, the
queue_command() function never calls the prepare_ring() function because
prepare_ring() is only supposed to be used for endpoint rings.  That means
the enqueue pointer will not be moved past the link TRB, and will get
overwritten.

The fix is to make queue_command() call prepare_ring() with a fake
endpoint status (set to running).  Then the enqueue pointer will get moved
past the link TRB.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

usbserial: Add AMOI Skypephone S2 support.

This patch adds support for the AMOI Skypephone S2 to the usbserial module.
Tested-by: Dennis Jansen <Dennis.Jansen@web.de>
Signed-off-by: Dennis Jansen <Dennis.Jansen@web.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Adds support for the Generic Qualcomm Gobi 2000 WWAN UMTS/CDMA modem
Signed-off-by: Andrew Bird <ajb@spheresytems.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

ftdi_sio: support for Signalyzer tools based on FTDI chips

This patch adds support for the Xverve Signalyzers.
Signed-off-by: Colin Leitner <colin.leitner@googlemail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

To escape from data abort in interrupt handler, it is required to
check for a connected gadget before delivering control requests.

The change fixes the following panic, which occurs with no loaded
gadget driver and input USB_REQ_GET_DESCRIPTOR request:

Kernel panic - not syncing: Fatal exception in interrupt
[<c0025874>] (unwind_backtrace+0x0/0xd8) from [<c0253f14>] (panic+0x40/0x110)
[<c0253f14>] (panic+0x40/0x110) from [<c002470c>] (die+0x154/0x180)
[<c002470c>] (die+0x154/0x180) from [<c0026448>] (__do_kernel_fault+0x64/0x74)
[<c0026448>] (__do_kernel_fault+0x64/0x74) from [<c0026610>] (do_page_fault+0x1b8/0x1cc)
[<c0026610>] (do_page_fault+0x1b8/0x1cc) from [<c00202d4>] (do_DataAbort+0x34/0x94)
[<c00202d4>] (do_DataAbort+0x34/0x94) from [<c0020a60>] (__dabt_svc+0x40/0x60)
Exception stack(0xc0327ea8 to 0xc0327ef0)
7ea0:                   bf0026b0 c0327ef0 c0327ee4 00000000 bf002590 00000093
7ec0: 00000001 bf0026b0 bf002990 00000000 00000008 0000143d 00003f00 c0327ef0
7ee0: bf001364 bf001360 20000093 ffffffff
[<c0020a60>] (__dabt_svc+0x40/0x60) from [<bf001360>] (s3c2410_udc_irq+0x5b8/0x778 [s3c2410_udc])
[<bf001360>] (s3c2410_udc_irq+0x5b8/0x778 [s3c2410_udc]) from [<c0058aa0>] (handle_IRQ_event+0x3c/0x104)
[<c0058aa0>] (handle_IRQ_event+0x3c/0x104) from [<c005a428>] (handle_edge_irq+0x12c/0x164)
[<c005a428>] (handle_edge_irq+0x12c/0x164) from [<c0020068>] (asm_do_IRQ+0x68/0x88)
[<c0020068>] (asm_do_IRQ+0x68/0x88) from [<c0020aa4>] (__irq_svc+0x24/0xa0)
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Nokia S60 phones expose two ACM channels. The first is
a modem, the second is 'vendor-specific' but is treated
as a serial device at the S60 end, so we want to expose
it on Linux too.
Signed-off-by: Przemo Firszt <przemo@firszt.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Add VID/PID for Sierra Wireless 250U USB dongle to sierra.c
Allows use of 3G radio only
Signed-off-by: August Huber <gus@pbx.org>
Cc: Elina Pasheva <epasheva@sierrawireless.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Omer Sezgin Ugurlu <omer.ugurlu@a-kent.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  ACPI / Sleep: Allow the NVS saving to be skipped during suspend to RAM
  ACPI: create "processor.bm_check_disable" boot param
  ACPI: skip checking BM_STS if the BIOS doesn't ask for it
  ACPI: fix unused function warning
  ACPI: processor: fix processor_physically_present on UP
  ACPI video: fix string mismatch for Sony SR290 laptop
  ACPI battery: don't invoke power_supply_changed twice when battery is hot-added
  ACPI: handle systems which asynchoronously enable ACPI mode

This fixes the regression in 2.6.35-rcX where bluetooth network devices
would fail to be deleted from sysfs, causing their destruction and
recreation to fail.  In addition this fixes the mac80211_hwsim driver
where it would leave around sysfs files when the driver was removed.

This problem is discussed at
  https://bugzilla.kernel.org/show_bug.cgi?id=16257

The reason for the regression is that the network namespace support
added to sysfs expects and requires that network devices be put in
directories that can contain only network devices.

Today get_device_parent almost provides that guarantee for all class
devices, except for a specific exception when the parent of a class
devices is a class device.  It would be nice to simply remove that
arguably incorrect special case, but apparently the input devices depend
on it being there.  So I have only removed it for class devices with
network namespace support.  Which today are the network devices.

It has been suggested that a better fix would be to change the parent
device from a class device to a bus device, which in the case of the
bluetooth driver would change /sys/class/bluetooth to /sys/bus/bluetoth,
I can not see how we would avoid significant userspace breakage if we
were to make that change.

Adding an extra directory in the path to the device will also be
userspace visible but it is much less likely to break things.
Everything is still accessible from /sys/class (for example), and it
fixes two bugs.  Adding an extra directory fixes a 3 year old regression
introduced with the new sysfs layout that makes it impossible to rename
bnep0 network devices to names that conflict with hci device attributes
like hci_revsion.  Adding an additional directory removes the new
failure modes introduced by the network namespace code.

If it weren't for the regession in the renaming of network devices I
would figure out how to just make the sysfs code deal with this
configuration of devices.

In summary this patch fixes regressions by changing:
"/sys/class/bluetooth/hci0/bnep0" to "/sys/class/bluetooth/hci0/net/bnep0".
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

virtio ring was changed to return an error code on OOM,
but one caller was missed and still checks for vq->vring.num.
The fix is just to check for <0 error code.

Long term it might make sense to change goto add_head to
just return an error on oom instead, but let's apply
a minimal fix for 2.6.35.
Reported-by: Chris Mason <chris.mason@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Tested-by: Chris Mason <chris.mason@oracle.com>
Cc: stable@kernel.org # .34.x
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 3fea6026 ("Input: twl40300-keypad - fix handling of "all
ground" rows") broke compilation as I managed to use non-existent
keycodes.
Reported-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 2a6b6976
(ACPI: Store NVS state even when entering suspend to RAM) caused the
ACPI suspend code save the NVS area during suspend and restore it
during resume unconditionally, although it is known that some systems
need to use acpi_sleep=s4_nonvs for hibernation to work.  To allow
the affected systems to avoid saving and restoring the NVS area
during suspend to RAM and resume, introduce kernel command line
option acpi_sleep=nonvs and make acpi_sleep=s4_nonvs work as its
alias temporarily (add acpi_sleep=s4_nonvs to the feature removal
file).

Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16396 .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: tomas m <tmezzadra@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  vmlinux.lds: fix .data..init_task output section (fix popwerpc boot)
  powerpc: Fix erroneous lmb->memblock conversions
  powerpc/mm: Add some debug output when hash insertion fails
  powerpc/mm: Fix bugs in huge page hashing
  powerpc/mm: Move around testing of _PAGE_PRESENT in hash code
  powerpc/mm: Handle hypervisor pte insert failure in __hash_page_huge
  powerpc/kexec: Fix boundary case for book-e kexec memory limits

* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
  nconfig: Fix segfault when help contains special characters
  kbuild: Fix make rpm
  kbuild: Make the setlocalversion script POSIX-compliant

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf tools: Fix fallback to cplus_demangle() when bfd_demangle() is not available
  perf annotate: Fix handling of goto labels that are valid hex numbers
  tracing: Properly align linker defined symbols
  perf symbols: Fix directory descriptor leaking
  perf: Fix various display bugs with parent filtering

nconfig segfaults when help text contains the character '%'. For a quick
example, navigate to the kernel compression options and get the help for
bzip2. Doing so triggers a call to mvwprintw() with a string containing
'%' and no extra arguments to fill in the specifier's value. Fix this
case by printing the literal string retrieved from the kconfig.

 #0  0x00002b52b6b11d83 in vfprintf () from /lib/libc.so.6
 #1  0x00002b52b6bad010 in __vsnprintf_chk () from /lib/libc.so.6
 #2  0x00002b52b623991b in _nc_printf_string () from
 /lib/libncursesw.so.5
 #3  0x00002b52b6234cff in vwprintw () from /lib/libncursesw.so.5
 #4  0x00002b52b6234db9 in mvwprintw () from /lib/libncursesw.so.5
 #5  0x00000000004151d8 in fill_window (win=0x21b64c0,
     text=0x21b62b0 "CONFIG_KERNEL_BZIP2:\n\nIts compression ratio and
     speed is intermediate.\nDecompression speed is slowest among the
     three.  The kernel\nsize is about 10% smaller with bzip2, in
     comparison to gzip.\nBzip2 us"...)
     at scripts/kconfig/nconf.gui.c:229
 #6  0x0000000000416335 in show_scroll_win (main_window=0x21a5630,
         title=0x157fa30 "Bzip2",
 	    text=0x21b62b0 "CONFIG_KERNEL_BZIP2:\n\nIts compression
 	    ratio and speed is intermediate.\nDecompression speed is
 	    slowest among the three.  The kernel\nsize is about 10%
 	    smaller with bzip2, in comparison to gzip.\nBzip2 us"...)
     at scripts/kconfig/nconf.gui.c:535
 #7  0x00000000004055b2 in show_help (menu=0x157f9d0)
         at scripts/kconfig/nconf.c:1257
 #8  0x0000000000405897 in conf_choice (menu=0x157f130)
 	    at scripts/kconfig/nconf.c:1321
 #9  0x0000000000405326 in conf (menu=0x157d130) at
 	    scripts/kconfig/nconf.c:1208
 #10 0x00000000004052e8 in conf (menu=0xb434a0) at
 	    scripts/kconfig/nconf.c:1203
 #11 0x0000000000406092 in main (ac=2, av=0x7fff96a93c38)

Cc: Michal Marek <mmarek@suse.cz>
Cc: Nir Tzachar <nir.tzachar@gmail.com>
Signed-off-by: Stephen Boyd <bebarino@gmail.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>

The .data..init_task output section was missing
a load offset causing a popwerpc target to fail to boot.

Sean MacLennan tracked it down to the definition of
INIT_TASK_DATA_SECTION().

There are only two users of INIT_TASK_DATA_SECTION()
in the kernel today: cris and popwerpc.
cris do not support relocatable kernels and is thus not
impacted by this change.

Fix INIT_TASK_DATA_SECTION() to specify load offset like
all other output sections.
Reported-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Oooops... we missed these. We incorrectly converted strings
used when parsing the device-tree on pseries, thus breaking
access to drconf memory and hotplug memory.

While at it, also revert some variable names that represent
something the FW calls "lmb" and thus don't need to be converted
to "memblock".
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---

This adds some debug output to our MMU hash code to print out some
useful debug data if the hypervisor refuses the insertion (which
should normally never happen).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---

There's a couple of nasty bugs lurking in our huge page hashing code.

First, we don't check the access permission atomically with setting
the _PAGE_BUSY bit, which means that the PTE value we end up using
for the hashing might be different than the one we have checked
the access permissions for.

We've seen cases where that leads us to try to use an invalidated
PTE for hashing, causing all sort of "interesting" issues.

Then, we also failed to set _PAGE_DIRTY on a write access.

Finally, a minor tweak but we should return 0 when we find the
PTE busy, in order to just re-execute the access, rather than 1
which means going to do_page_fault().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---

Instead of adding _PAGE_PRESENT to the access permission mask
in each low level routine independently, we add it once from
hash_page().

We also move the preliminary access check (the racy one before
the PTE is locked) up so it applies to the huge page case. This
duplicates code in __hash_page_huge() which we'll remove in a
subsequent patch to fix a race in there.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

If the hypervisor gives us an error on a hugepage insert we panic. The
normal page code already handles this by returning an error instead and we end
calling low_hash_fault which will just kill the task if possible.

The patch below does a similar thing for the hugepage case.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

processor.bm_check_disable=1" prevents Linux from checking BM_STS
before entering C3-type cpu power states.

This may be useful for a system running acpi_idle
where the BIOS exports FADT C-states, _CST IO C-states,
or _CST FFH C-states with the BM_STS bit set;
while configuring the chipset to set BM_STS
more frequently than perhaps is optimal.

Note that such systems may have been developed
using a tickful OS that would quickly clear BM_STS,
rather than a tickless OS that may go for some time
between checking and clearing BM_STS.

Note also that an alternative for newer systems
is to use the intel_idle driver, which always
ignores BM_STS, relying Linux device drivers
to register constraints explicitly via PM_QOS.

https://bugzilla.kernel.org/show_bug.cgi?id=15886Signed-off-by: Len Brown <len.brown@intel.com>

It turns out that there is a bit in the _CST for Intel FFH C3
that tells the OS if we should be checking BM_STS or not.

Linux has been unconditionally checking BM_STS.
If the chip-set is configured to enable BM_STS,
it can retard or completely prevent entry into
deep C-states -- as illustrated by turbostat:

http://userweb.kernel.org/~lenb/acpi/utils/pmtools/turbostat/

ref: Intel Processor Vendor-Specific ACPI Interface Specification
table 4 "_CST FFH GAS Field Encoding"
Bit 1: Set to 1 if OSPM should use Bus Master avoidance for this C-state

https://bugzilla.kernel.org/show_bug.cgi?id=15886Signed-off-by: Len Brown <len.brown@intel.com>

make version 3.80 doesn't support "else ifdef" on the same line, also it
doesn't support unindented nested constructs.

Build fails with:
Makefile:608: Extraneous text after `else' directive
Makefile:611: *** only one `else' per conditional.  Stop.

This patch fixes the build for make 3.80.

Cc: Ingo Molnar <mingo@elte.hu>,
Cc: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <1278430783-17259-1-git-send-email-conny.seidel@amd.com>
Signed-off-by: Conny Seidel <conny.seidel@amd.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: synaptics - relax capability ID checks on newer hardware
  Input: twl40300-keypad - fix handling of "all ground" rows
  Input: gamecon - reference correct pad in gc_psx_command()
  Input: gamecon - reference correct input device in NES mode
  Input: w90p910_keypad - change platfrom driver name to 'nuc900-kpi'
  Input: i8042 - add Gigabyte Spring Peak to dmi_noloop_table
  Input: qt2160 - rename kconfig symbol name

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/radeon/kms: add quirk to make HP DV5000 laptop resume
  drm/radeon/kms: fix RADEON_INFO_CRTC_FROM_ID info ioctl
  Fix ttm_page_alloc.c build breakage
  drm/radeon/kms: fix legacy LVDS dpms sequence
  drm/radeon/kms: drop taking lock around crtc lookup.