Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2016-03-29

This series contains fixes to ixgbe and ixgbevf.

Tushar fixes an issue which was introduced with an earlier commit, where
hardware register RAR0 default MAC address does not get set properly.

Alex fixes two issues, first being the VXLAN port number should be stored
in network order instead of in host order.  The second fix corrects the ATR
code to handle IPv6 extension headers.  The issue was ATR code was assuming
that it would be able to use tcp_hdr for every TCP frame that came through,
but that is not the case, which resulted in bad filters being setup.

Mark fixes a use of usleep_range() to udelay() in the case where a lock
is being held.

Stefan fixes the offline self tests where ndo_stop() should be used instead
of ndo_close(), which causes IFF_UP to be cleared and interface routes get
removed.

Emil fixes the error case where we need to return an error when a MAC
address change is rejected by the PF.  This helps prevent the user from
modifying the MAC address when the operation is not permitted.

Sridhar provides three fixes for ixgbe, all dealing with traffic class
offload handling.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Make the 2 byte padding in struct bpf_tunnel_key between tunnel_ttl
and tunnel_label members explicit. No issue has been observed, and
gcc/llvm does padding for the old struct already, where tunnel_label
was not yet present, so the current code works, but since it's part
of uapi, make sure we don't introduce holes in structs.

Therefore, add tunnel_ext that we can use generically in future
(f.e. to flag OAM messages for backends, etc). Also add the offset
to the compat tests to be sure should some compilers not padd the
tail of the old version of bpf_tunnel_key.

Fixes: 4018ab18 ("bpf: support flow label for bpf_skb_{set, get}_tunnel_key")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

IPv6 counters updates use a different macro than IPv4.

Fixes: 36cbb245 ("udp: Increment UDP_MIB_IGNOREDMULTI for arriving unmatched multicasts")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Rick Jones <rick.jones2@hp.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To report flow control tx/rx settings accurately regardless of autoneg
setting, we should use link_info->req_flow_ctrl.  Before this patch,
the reported settings were only correct when autoneg was on.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The typo caused the wrong flow control bit to be set.

Reported by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The size of every padded firmware message is specified in the first
HWRM_VER_GET response message.  Use this value to pad every message
after that.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The existing code does the following:
    allocate completion ring
    initialize completion ring doorbell
    disable interrupts on this completion ring by writing to the doorbell

We can have a race where firmware sends an asynchronous event to the host
after completion ring allocation and before doorbell is initialized.
When this happens driver can crash while ringing the doorbell using
uninitialized value as part of handling the IRQ/napi request.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is an issue when we use mavtap over team:
When we replug nic links from team0, the real nics's mc list will not
include the maddr for macvtap any more. then we can't receive pkts to
macvtap device, as they are filterred by mc list of nic.

In Bonding Driver, it syncs the uc/mc addrs in bond_enslave().

We will fix this issue on team by adding the port's uc/mc addrs sync in
team_port_add.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch should fix the issues seen with a recent fix to prevent
tunnel-in-tunnel frames from being generated with GRO.  The fix itself is
correct for now as long as we do not add any devices that support
NETIF_F_GSO_GRE_CSUM.  When such a device is added it could have the
potential to mess things up due to the fact that the outer transport header
points to the outer UDP header and not the GRE header as would be expected.

Fixes: fac8e0f5 ("tunnels: Don't apply GRO to multiple layers of encapsulation.")
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

in the case where qed_slowpath_irq_req is not called, rc is not
assigned and so qed_int_igu_enable will return a garbage value.
Fix this by initializing rc to 0.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Somehow my patch for commit cea8768f ("sctp: allow
sctp_transmit_packet and others to use gfp") missed two important
chunks, which are now added.

Fixes: cea8768f ("sctp: allow sctp_transmit_packet and others to use gfp")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-By: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When NET_SWITCHDEV=n, switchdev_port_attr_set will return -EOPNOTSUPP,
we should ignore this error code and continue to set the ageing time.

Fixes: c62987bb ("bridge: push bridge setting ageing_time down to switchdev")
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix support for 16 bit source/dest port matches in ixgbe model.
u32 uses a single 32-bit key value for both source and destination ports
starting at offset 0. So replace the 2 functions with a single function
that takes this key value/mask to program both source and dest ports.

Verified with the following filter:

 #tc qdisc add dev p4p1 ingress
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 1: u32 divisor 1
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 800:0:10 u32 ht 800: link 1: \
	offset at 0 mask 0f00 shift 6 plus 0 eat match ip protocol 6 ff
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 1:0:10 u32 ht 1: \
	match tcp src 1024 ffff match tcp dst 80 ffff action drop
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 1:0:11 u32 ht 1: \
	match tcp src 1025 ffff action drop
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 1:0:12 u32 ht 1: \
	match tcp dst 81 ffff action drop
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove the incorrect check for mask in ixgbe_configure_clsu32 and
drop the 'mask' field that is not required in struct ixgbe_mat_field

Verified with the following filters:

 #tc qdisc add dev p4p1 ingress
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 800:0:1 u32 ht 800: \
	match ip dst 10.0.0.1/8 match ip src 10.0.0.2/8 action drop
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 800:0:2 u32 ht 800: \
	match ip dst 11.0.0.1/16 match ip src 11.0.0.2/16 action drop
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 800:0:3 u32 ht 800: \
	match ip dst 12.0.0.1/24 match ip src 12.0.0.2/24 action drop
 #tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
	handle 800:0:4 u32 ht 800: \
	match ip dst 13.0.0.1/32 match ip src 13.0.0.2/32 action drop
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Check for handle ids when adding/deleting hash nodes OR adding/deleting
filter entries and limit them to max number of links or header nodes
supported(IXGBE_MAX_LINK_HANDLE).

Start from bit 0 when setting hash table bit-map.(adapter->tables)
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This function is only used in ixgbe_main.c
Resolves a "missing prototype" warning when building the driver with W=1
Reported-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Return error when a MAC address change is rejected by the PF.

This will prevent the user from modifying the MAC address when
that operation is not permitted.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Use udelay instead of usleep_range because this can be called while
a lock is held.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The ATR code was assuming that it would be able to use tcp_hdr for
every TCP frame that came through.  However this isn't the case as it
is possible for a frame to arrive that is TCP but sent through something
like a raw socket.  As a result the driver was setting up bad filters in
which tcp_hdr was really pointing to the network header so the data was
all invalid.

In order to correct this I have added a bit of parsing logic that will
determine the TCP header location based off of the network header and
either the offset in the case of the IPv4 header, or a walk through the
IPv6 extension headers until it encounters the header that indicates
IPPROTO_TCP.  In addition I have added checks to verify that the lowest
protocol provided is recognized as IPv4 or IPv6 to help mitigate raw
sockets using ETH_P_ALL from having ATR applied to them.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The VXLAN port number should be stored in network order instead of in host
order as it is accessed from the hot-path in ATR.  This way we can avoid
having to do any byte swaps in order to validate the port number.

I moved the vxlan_port value into a hole in the read-mostly region of the
adapter struct.  This way it should be in a warm cache-line instead of in
some isolated region in memory when it needs to be accessed.

In addition I went through and stripped a bunch of unneeded ifdef flags
since having an extra variable present doesn't really hurt anything and
makes the code easier to read.  I also went through and dropped the
NETIF_F_RXCSUM flag which was being set in hw_encap_features but provides
no value as the flag is not evaluated in the Rx path.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

commit c9f53e63 ("ixgbe: Refactor MAC address configuration code")
introduced code that doesn't set HW register RAR0 to default mac address
but FF:FF:FF:FF:FF:FF. Due to this, ixgbe HW discards all incoming packets
that doesn't have destination mac address equals to FF:FF:FF:FF:FF:FF.

This commit sets RAR0 correctly to default HW mac address.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Tested-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Thomas reports:
"Windows:

00 diagnostics
01 modem
02 at-port
03 nmea
04 nic

Linux:

T:  Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=  4 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=2001 ProdID=7e19 Rev=02.32
S:  Manufacturer=Mobile Connect
S:  Product=Mobile Connect
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage"
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for you net tree,
they are:

1) There was a race condition between parallel save/swap and delete,
   which resulted a kernel crash due to the increase ref for save, swap,
   wrong ref decrease operations. Reported and fixed by Vishwanath Pai.

2) OVS should call into CT NAT for packets of new expected connections only
   when the conntrack state is persisted with the 'commit' option to the
   OVS CT action. From Jarno Rajahalme.

3) Resolve kconfig dependencies with new OVS NAT support. From Arnd Bergmann.

4) Early validation of entry->target_offset to make sure it doesn't take us
   out from the blob, from Florian Westphal.

5) Again early validation of entry->next_offset to make sure it doesn't take
   out from the blob, also from Florian.

6) Check that entry->target_offset is always of of sizeof(struct xt_entry)
   for unconditional entries, when checking both from check_underflow()
   and when checking for loops in mark_source_chains(), again from
   Florian.

7) Fix inconsistent behaviour in nfnetlink_queue when
   NFQA_CFG_F_FAIL_OPEN is set and netlink_unicast() fails due to buffer
   overrun, we have to reinject the packet as the user expects.

8) Enforce nul-terminated table names from getsockopt GET_ENTRIES
   requests.

9) Don't assume skb->sk is set from nft_bridge_reject and synproxy,
   this fixes a recent update of the code to namespaceify
   ip_default_ttl, patch from Liping Zhang.

This batch comes with four patches to validate x_tables blobs coming
from userspace. CONFIG_USERNS exposes the x_tables interface to
unpriviledged users and to be honest this interface never received the
attention for this move away from the CAP_NET_ADMIN domain. Florian is
working on another round with more patches with more sanity checks, so
expect a bit more Netfilter fixes in this development cycle than usual.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit fa50d974 ("ipv4: Namespaceify ip_default_ttl sysctl knob")
use sock_net(skb->sk) to get the net namespace, but we can't assume
that sk_buff->sk is always exist, so when it is NULL, oops will happen.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Reviewed-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Make sure the table names via getsockopt GET_ENTRIES is nul-terminated
in ebtables and all the x_tables variants and their respective compat
code. Uncovered by KASAN.
Reported-by: Baozeng Ding <sploving1@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

When netlink unicast fails to deliver the message to userspace, we
should also check if the NFQA_CFG_F_FAIL_OPEN flag is set so we reinject
the packet back to the stack.

I think the user expects no packet drops when this flag is set due to
queueing to userspace errors, no matter if related to the internal queue
or when sending the netlink message to userspace.

The userspace application will still get the ENOBUFS error via recvmsg()
so the user still knows that, with the current configuration that is in
place, the userspace application is not consuming the messages at the
pace that the kernel needs.
Reported-by: "Yigal Reiss (yreiss)" <yreiss@cisco.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Tested-by: "Yigal Reiss (yreiss)" <yreiss@cisco.com>

Ben Hawkes says:

 In the mark_source_chains function (net/ipv4/netfilter/ip_tables.c) it
 is possible for a user-supplied ipt_entry structure to have a large
 next_offset field. This field is not bounds checked prior to writing a
 counter value at the supplied offset.

Problem is that mark_source_chains should not have been called --
the rule doesn't have a next entry, so its supposed to return
an absolute verdict of either ACCEPT or DROP.

However, the function conditional() doesn't work as the name implies.
It only checks that the rule is using wildcard address matching.

However, an unconditional rule must also not be using any matches
(no -m args).

The underflow validator only checked the addresses, therefore
passing the 'unconditional absolute verdict' test, while
mark_source_chains also tested for presence of matches, and thus
proceeeded to the next (not-existent) rule.

Unify this so that all the callers have same idea of 'unconditional rule'.
Reported-by: Ben Hawkes <hawkes@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Otherwise this function may read data beyond the ruleset blob.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

We should check that e->target_offset is sane before
mark_source_chains gets called since it will fetch the target entry
for loop detection.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

The openvswitch code has gained support for calling into the
nf-nat-ipv4/ipv6 modules, however those can be loadable modules
in a configuration in which openvswitch is built-in, leading
to link errors:

net/built-in.o: In function `__ovs_ct_lookup':
:(.text+0x2cc2c8): undefined reference to `nf_nat_icmp_reply_translation'
:(.text+0x2cc66c): undefined reference to `nf_nat_icmpv6_reply_translation'

The dependency on (!NF_NAT || NF_NAT) prevents similar issues,
but NF_NAT is set to 'y' if any of the symbols selecting
it are built-in, but the link error happens when any of them
are modular.

A second issue is that even if CONFIG_NF_NAT_IPV6 is built-in,
CONFIG_NF_NAT_IPV4 might be completely disabled. This is unlikely
to be useful in practice, but the driver currently only handles
IPv6 being optional.

This patch improves the Kconfig dependency so that openvswitch
cannot be built-in if either of the two other symbols are set
to 'm', and it replaces the incorrect #ifdef in ovs_ct_nat_execute()
with two "if (IS_ENABLED())" checks that should catch all corner
cases also make the code more readable.

The same #ifdef exists ovs_ct_nat_to_attr(), where it does not
cause a link error, but for consistency I'm changing it the same
way.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 05752523 ("openvswitch: Interface with NAT.")
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

OVS should call into CT NAT for packets of new expected connections only
when the conntrack state is persisted with the 'commit' option to the
OVS CT action.  The test for this condition is doubly wrong, as the CT
status field is ANDed with the bit number (IPS_EXPECTED_BIT) rather
than the mask (IPS_EXPECTED), and due to the wrong assumption that the
expected bit would apply only for the first (i.e., 'new') packet of a
connection, while in fact the expected bit remains on for the lifetime of
an expected connection.  The 'ctinfo' value IP_CT_RELATED derived from
the ct status can be used instead, as it is only ever applicable to
the 'new' packets of the expected connection.

Fixes: 05752523 ('openvswitch: Interface with NAT.')
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

This fix adds a new reference counter (ref_netlink) for the struct ip_set.
The other reference counter (ref) can be swapped out by ip_set_swap and we
need a separate counter to keep track of references for netlink events
like dump. Using the same ref counter for dump causes a race condition
which can be demonstrated by the following script:

ipset create hash_ip1 hash:ip family inet hashsize 1024 maxelem 500000 \
counters
ipset create hash_ip2 hash:ip family inet hashsize 300000 maxelem 500000 \
counters
ipset create hash_ip3 hash:ip family inet hashsize 1024 maxelem 500000 \
counters

ipset save &

ipset swap hash_ip3 hash_ip2
ipset destroy hash_ip3 /* will crash the machine */

Swap will exchange the values of ref so destroy will see ref = 0 instead of
ref = 1. With this fix in place swap will not succeed because ipset save
still has ref_netlink on the set (ip_set_swap doesn't swap ref_netlink).

Both delete and swap will error out if ref_netlink != 0 on the set.

Note: The changes to *_head functions is because previously we would
increment ref whenever we called these functions, we don't do that
anymore.
Reviewed-by: Joshua Hunt <johunt@akamai.com>
Signed-off-by: Vishwanath Pai <vpai@akamai.com>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

GPIOlib will print warning messages if we call GPIO functions without a
valid GPIO. Change the code to avoid doing so.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It may fail to set coalesce usecs to HW, and Ethtool needs to know if it
is successful to cfg the parameter or not. So it needs return the errno by
dsaf.ko.
Signed-off-by: Lisheng <lisheng011@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The overtime setting and getting REGs in HNS V2 is defferent from HNS V1.
It needs to be distinguished between them if getting or setting the REGs.
Signed-off-by: Lisheng <lisheng011@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For the input parameter count, it's better to use the size
of destination buffer size, as nla_memcpy would take into
account the length of the source netlink attribute when
a data is copied from an attribute.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In ravb_start_xmit dont call skb_tx_timestamp only when hardware
timestamping is requested: in the latter case software timestamps are
suppressed and thus the call of skb_tx_timestamp does not have any effect.

Instead call skb_tx_timestamp unconditionally in ravb_start_xmit, since
the function checks itself if software timestamping is required or should
be skipped due to hardware timestamping.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to use post-decrement to ensure that irq_dispose_mapping is
also called on priv->rxq[0]->irq_no; moreover, if one of the above for
loops failed already at i==0 (so we reach one of these labels with
that value of i), we'll enter an essentially infinite loop of
out-of-bounds accesses.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>