Here's some cleanups/fixes/changes for interrupts on 2.5.67 + ia64.
Specifically:

  - Cleanup some ugliness with polarity/trigger setup.

  - Add iosapic_enable_intr() to set_rte on an interupt when the
    device is enabled.  IMHO, we really only want to unmask RTEs
    for PRTs we might actually use.  This moves the interrupt
    distribution here too.

  - When changing a vector from edge to level, call register_intr()
    to do it so all the data structures get set correctly.  If we
    have to guess how to setup an interupt and get it wrong, this
    should close some holes in changing it back to the correct type.

  - Register the HCDP interrupt in 8250_hcdp - this is where we have
    to guess the polarity/trigger.  The real handler will get fixed
    up via PCI setup or ACPI namespace serial support, this gets it
    associated w/ the port at setup.  This should allow interrupts
    to work when using builtin UARTs as console on HP Itanium2 boxes.

This patch fixes the issue of some CPUs not showing timer interrupts
going off.  Seems during the process of sync'ing the itc, we jumped over
the next timer value.  This patch is against 2.5.67 + ia64.  I haven't
seen the problem on 2.4, but a quick looks seems like it's potentially
an issue there too.

Please apply the following patch on top of 2.5.6x. This patch does the
following:

- repair broken system-wide overflow notification
- repair broken per-process notification
- fix a problem in the resrved bitmask for opcode 
  matcher8,9 for McKinley as reported by UIUC.
- forcing of bit2 for pmc8/pmc9 now part of reserved bitmask
- add the unsecure option to perfmon
- update to perfmon 1.4 (similar to 2.4)

	with a special convention.  Various minor fixes for gcc-pre3.4.

This is mostly trivial whitespace and printk text tweaks.  I did add the
segment number to a printk that previously just had the bus.

Include id when encountering unknown IOC.

This removes a workaround for some broken firmware that was
never released.

> It looks like dynamic x86 binaries have a problem once again (or
> still).  If I try to run any shared x86 binaries, I get:
> 
>       $ ls.x86
>       ls.x86: error while loading shared libraries: librt.so.1: cannot map zero-fill pages: Error 14
> 
> Would someone take a look?

We saw this behavior with 2.5.59 also. The attached work around should
take care of the problem temporarily. Last time this happened, IA-32
programs were doing mmaps, whose size was one page bigger than the
size of the underlying file (even after rounding up the file size).

I never got a chance to figure out why glibc was doing mmaps with the
wrong size. Also, I failed to reproduce the problem with a more
recent (RH 8.0) glibc.

Which version of IA-32 glibc were you using ?

	int.

	help of ia64_fetchadd() macro.  Ditto for _raw_read_unlock().

This patch fixes waste of interrupt vector pool by not
allocating an interrupt vector to a GSI which has no corresponding
IO SAPIC.

This fix is needed to boot on Intel-based machines.

This fixes a couple problems with the generic target in the latest
2.5.67 kernel.  First is simply a fix for the addition of readX in
the machvec.  The second gets things to link in roughly the same order
when using a generic vs zx1 flavor.  With the current code, sba_init()
is called in the right place when using a zx1 flavor kernel, but
happens way too early on a generic kernel.

	Various small 2.5.67 fixes.

Here is a trivial patch to processor.h to change "extern" to "static".

Here is the ia64 part of the patch.  It depends on my previous COMPAT
patches.  This is safe to apply even before Linus applies the generic
part.

Here is the ia64 part of the patch.  Pleas apply after Linus has applied
the generic part.

	Chandra Kapate).

implies that it should vary between 0-7, not any further (the
higher bits are done by updating current_vector by 8).

This also means that we don't have any overflow condition.

This version fixes:
- missing rtnl_lock()/rtnl_unload() bug on unregister_hdlc_device
- N2, C101: interrupt handler now works under high IRQ load from other
  devices (with previous versions, the IRQ processing for the card could
  sometimes stop after reaching "work limit")

This is production-tested on devices I have access to (N2, C101, PC300,
PCI200SYN).

This patch disables irqbalance and doesn't spawn a kernel thread for
systems which run SMP kernels and only have one online cpu.

This finally kills of blk_queue_empty().  This is similar to the patch I
recently sent to fix the SCSI logic as well.  A lot of drivers are doing
this in our core, mainly because that is the way they always did it:

start_queue:
	if (blk_queue_empty(q))
		return;

	rq = elv_next_request(q);
	if (!rq)
		return;

Patch simply removes the blk_queue_empty() check, and adds a check for
!rq return from elv_next_request() if the driver didn't already do that.

Additionally, the AS io scheduler can return NULL from
elv_next_request() if it thinks this is best. This way we are also
prepared for that to work well.

Patch was done by Nick Piggin.

Bug report from J Sanchez in #kernelnewbies

into home.transmeta.com:/home/torvalds/v2.5/linux

The problem with setiathome is that it displays something every now and
then - so it gets a backboost from X, and hovers at a relatively high
priority.