use different kill_ack_mask and kill_cts_mask when detect SCO
is active.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Change to offical name for 100 devices:
   "Intel(R) Centrino(R) Wireless-N 100"

Change to offical name for 130 devices:
   "Intel(R) Centrino(R) Wireless-N 130"
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Change to offical name for 6000g2b devices:
   "Intel(R) Centrino(R) Wireless-N 1030"
   "Intel(R) Centrino(R) Advanced-N 6230"
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Change to offical name for 6000g2a devices:
   "Intel(R) Centrino(R) Advanced-N 6205"
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Change to offical name for 6050g2 devices:
   "Intel(R) Centrino(R) Wireless-N 6150"
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Instead of hardcoding the numbers that must
match mac80211, use the constants. Not that
this means we could change the constants,
but at least this way it's clearer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Our hardware has reliable TX status, but we're
not currently advertising that to mac80211.
Since the packet loss monitoring will depend
on it, advertise it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Since aggregation queues are station-specific, the
device will not reject packets in them but rather
will stop the appropriate aggregation queues when
a station goes to sleep. I forgot to account for
this in the driver, so if a station went to sleep
that had aggregation enabled, traffic would stop
indefinitely.

Fix this by only accounting frames queued on the
normal AC queues for associated station.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Through races, a packet may be enqueued for
transmission to a station while that station
is going to sleep, in which case the warning
here triggers. Instead of warning, check the
condition -- if this packet is not a PS-poll
response then we still enqueue it but it will
be rejected by the device since the station
is marked as asleep.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

The valid tx/rx antenna information is part of EEPROM, so use it
to configure the device.

For few cases, the EEPROM did not reflect the correct antenna, but
it is too late to modify the EEPROM, so overwrite with .cfg parameters
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

was not used, remove it
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

It is no longer used anywhere
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Categorize AR7010 & AR9287 devices based on driver_info
of usb_device_id, instead of PIDs. This avoids per-device cases
and minimize code changes for new device addition.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

AR9287 devices (PCI/USB) use different eeprom start location
to read nvram. New devices might endup with same devid. So use
driver_info to set offset, instead of devid. driver_info is
valid for HTC devices alone which is filled in usb_device_id.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Added driver_info to identify AR7010, R9287 HTC devices.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The driver_info stores the device category information which
is used to load appropriate device firmware, select firmware offset
and eeprom starting location. The driver_info is accessed across
ath9k_htc and ath9k_hw. Hence placed under common structure.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For 6000g2b and up, adding advance power management support
for better power consumption
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If shadow register is enable, modify the power management
command to inform uCode
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Check the BT PSPoll flag when fill PM command to uCode
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Adding additional power management option available for the device.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Bit 7 of BT config flag is used to enable/disable PSPoll sync.
Make the name to match it.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For drivers that have accurate TX status reporting
we can report the number of consecutive lost packets
to userspace using the new cfg80211 CQM event. The
threshold is fixed right now, this may need to be
improved in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This adds the ability for drivers to use CQM events
to notify about packet loss for specific stations
(which could be the AP for the managed mode case).
Since the threshold might be determined by the
driver (it isn't passed in right now) it will be
passed out of the driver to userspace in the event.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This should help with latency issues which can happen when
using aggregation.

Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Matt Smith <matt.smith@atheros.com>
Cc: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This should help with latency issues which can happen when
using aggregation.

Cc: Matt Smith <matt.smith@atheros.com>
Cc: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since nullfunc frames are transmitted as unicast frames, they're more
reliable than the broadcast probe requests, so we need fewer retries
to figure out whether the AP is really gone.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

nullfunc frames are better for connection monitoring, because probe requests
are answered even if the AP has already dropped the connection, whereas
nullfunc frames from an unassociated station will trigger a disassoc/deauth
frame from the AP (WLAN_REASON_CLASS3_FRAME_FROM_NONASSOC_STA), which allows
the station to reconnect immediately instead of waiting until it attempts to
transmit the next unicast frame.

This only works on hardware with reliable tx ACK reporting, any other hardware
needs to fall back to the probe request method.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

- store the multicast rate as an index instead of the rate value
  (reduces cpu overhead in a hotpath)
- validate the rate values (must match a bitrate in at least one sband)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Check the connection by probing the AP (either using nullfunc or a
probe request). If nullfunc probing is supported and the assoc is no
longer valid, the AP will send a disassoc/deauth immediately.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Instead of using a fixed 2 second timeout, calculate beacon loss interval
from the advertised beacon interval and a frame count.  With this beacon
loss happens after N (default 7) consecutive frames are missed which
for a typical setup (100TU beacon interval) is ~700ms (or ~1/3 previous).
Signed-off-by: Sam Leffler <sleffler@chromium.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Paul Stewart <pstew@google.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Remove some typos, warnings, initialize some values to follow wl's code path.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Additional comment by Larry Finger <Larry.Finger@lwfinger.net>:

This change deserves a bit more explanation. You might include something like
"These tables came from reverse engineering the 5.10.56.46 version of the
Broadcom driver. Trace comparisons between b43 and the current Broadcom driver
(5.10.120.0) show byte reversals for the PHY register writes."
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

No change in output for pr_<level> prefixes.
netdev_<level> output is different, arguably improved.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>