Once anon_inode_getfd() has succeeded, it's impossible to undo
in a clean way and no, sys_close() is not usable in such cases.
Use anon_inode_getfile() and get_unused_fd_flags() to get struct file
and descriptor and do *not* install the file into the descriptor table
until after the last possible failure exit.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

This reverts commit 77ecc085fed1af1000ca719522977b960aa6da52.

Al Viro colorfully says: "You should *NEVER* use sys_close() on failure
exit paths like that.  Moreover, this kvm_put_kvm() becomes a double-put,
since closing the damn file will drop that reference to kvm.  Please,
revert.  anon_inode_getfd() should be used only when there's no possible
failures past its call".
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

The failure of create debugfs of VM will return directly without release
the anon file. It will leak memory and file descriptors, even through
be not serious.
Signed-off-by: Liu Shuo <shuo.a.liu@intel.com>
Fixes: 536a6f88Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

When freeing the nested resources of a vcpu, there is an assumption that
the vcpu's vmcs01 is the current VMCS on the CPU that executes
nested_release_vmcs12(). If this assumption is violated, the vcpu's
vmcs01 may be made active on multiple CPUs at the same time, in
violation of Intel's specification. Moreover, since the vcpu's vmcs01 is
not VMCLEARed on every CPU on which it is active, it can linger in a
CPU's VMCS cache after it has been freed and potentially
repurposed. Subsequent eviction from the CPU's VMCS cache on a capacity
miss can result in memory corruption.

It is not sufficient for vmx_free_vcpu() to call vmx_load_vmcs01(). If
the vcpu in question was last loaded on a different CPU, it must be
migrated to the current CPU before calling vmx_load_vmcs01().
Signed-off-by: Jim Mattson <jmattson@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Between loading the new VMCS and enabling PML, the CPU was unpinned.
If the vCPU thread were migrated to another CPU in the interim (e.g.,
due to preemption or sleeping alloc_page), then the VMWRITEs to enable
PML would target the wrong VMCS -- or no VMCS at all:

  [ 2087.266950] vmwrite error: reg 200e value 3fe1d52000 (err -506126336)
  [ 2087.267062] vmwrite error: reg 812 value 1ff (err 511)
  [ 2087.267125] vmwrite error: reg 401e value 12229c00 (err 304258048)

This patch ensures that the VMCS remains current while enabling PML by
doing the VMWRITEs while the CPU is pinned. Allocation of the PML buffer
is hoisted out of the critical section.
Signed-off-by: Peter Feiner <pfeiner@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

I don't know what I was thinking when I wrote commit 46896c73 ("KVM:
svm: add support for RDTSCP", 2015-11-12); I missed write_rdtscp_aux which
obviously uses MSR_TSC_AUX.

Therefore we do need to save/restore MSR_TSC_AUX in svm_vcpu_run.

Cc: stable@vger.kernel.org
Cc: Borislav Petkov <bp@alien8.de>
Fixes: 46896c73 ("KVM: svm: add support for RDTSCP")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

The following #PF may occurs:
[ 1403.317041] BUG: unable to handle kernel paging request at 0000000200000068
[ 1403.317045] IP: [<ffffffffc04c20b0>] __mtrr_lookup_var_next+0x10/0xa0 [kvm]

[ 1403.317123] Call Trace:
[ 1403.317134]  [<ffffffffc04c2a65>] ? kvm_mtrr_check_gfn_range_consistency+0xc5/0x120 [kvm]
[ 1403.317143]  [<ffffffffc04ac11f>] ? tdp_page_fault+0x9f/0x2c0 [kvm]
[ 1403.317152]  [<ffffffffc0498128>] ? kvm_set_msr_common+0x858/0xc00 [kvm]
[ 1403.317161]  [<ffffffffc04b8883>] ? x86_emulate_insn+0x273/0xd30 [kvm]
[ 1403.317171]  [<ffffffffc04c04e4>] ? kvm_cpuid+0x34/0x190 [kvm]
[ 1403.317180]  [<ffffffffc04a5bb9>] ? kvm_mmu_page_fault+0x59/0xe0 [kvm]
[ 1403.317183]  [<ffffffffc0d729e1>] ? vmx_handle_exit+0x1d1/0x14a0 [kvm_intel]
[ 1403.317185]  [<ffffffffc0d75f3f>] ? atomic_switch_perf_msrs+0x6f/0xa0 [kvm_intel]
[ 1403.317187]  [<ffffffffc0d7621d>] ? vmx_vcpu_run+0x2ad/0x420 [kvm_intel]
[ 1403.317196]  [<ffffffffc04a0962>] ? kvm_arch_vcpu_ioctl_run+0x622/0x1550 [kvm]
[ 1403.317204]  [<ffffffffc049abb9>] ? kvm_arch_vcpu_load+0x59/0x210 [kvm]
[ 1403.317206]  [<ffffffff81036245>] ? __kernel_fpu_end+0x35/0x100
[ 1403.317213]  [<ffffffffc0487eb6>] ? kvm_vcpu_ioctl+0x316/0x5d0 [kvm]
[ 1403.317215]  [<ffffffff81088225>] ? do_sigtimedwait+0xd5/0x220
[ 1403.317217]  [<ffffffff811f84dd>] ? do_vfs_ioctl+0x9d/0x5c0
[ 1403.317224]  [<ffffffffc04928ae>] ? kvm_on_user_return+0x3e/0x70 [kvm]
[ 1403.317225]  [<ffffffff811f8a74>] ? SyS_ioctl+0x74/0x80
[ 1403.317227]  [<ffffffff815bf0b6>] ? entry_SYSCALL_64_fastpath+0x1e/0xa8
[ 1403.317242] RIP  [<ffffffffc04c20b0>] __mtrr_lookup_var_next+0x10/0xa0 [kvm]

At mtrr_lookup_fixed_next(), when the condition
'if (iter->index >= ARRAY_SIZE(iter->mtrr_state->fixed_ranges))' becomes true,
mtrr_lookup_var_start() is called with iter->range with gargabe values from the
fixed MTRR union field. Then, list_prepare_entry() do not call list_entry()
initialization, keeping a garbage pointer in iter->range which is accessed in
the following __mtrr_lookup_var_next() call.

Fixes: f571c097Signed-off-by: Alexis Dambricourt <alexis@blade-group.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Pull fuse fix from Miklos Szeredi:
 "This makes sure userspace filesystems are not broken by the parallel
  lookups and readdir feature"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: serialize dirops by default

Pull overlayfs fixes from Miklos Szeredi:
 "This contains fixes for a dentry leak, a regression in 4.6 noticed by
  Docker users and missing write access checking in truncate"

* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
  ovl: warn instead of error if d_type is not supported
  ovl: get_write_access() in truncate
  ovl: fix dentry leak for default_permissions

overlay needs underlying fs to support d_type. Recently I put in a
patch in to detect this condition and started failing mount if
underlying fs did not support d_type.

But this breaks existing configurations over kernel upgrade. Those who
are running docker (partially broken configuration) with xfs not
supporting d_type, are surprised that after kernel upgrade docker does
not run anymore.

https://github.com/docker/docker/issues/22937#issuecomment-229881315

So instead of erroring out, detect broken configuration and warn
about it. This should allow existing docker setups to continue
working after kernel upgrade.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 45aebeaf ("ovl: Ensure upper filesystem supports d_type")
Cc: <stable@vger.kernel.org> 4.6

Pull MIPS fix from Ralf Baechle:
 "Only a single fix for 4.7 pending at this point.  It fixes an issue
  that may lead to corruption of the cache mode bits in the page table"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Fix possible corruption of cache mode by mprotect.

Pull powerpc fixes from Michael Ellerman:

 - tm: Always reclaim in start_thread() for exec() class syscalls from
   Cyril Bur

 - tm: Avoid SLB faults in treclaim/trecheckpoint when RI=0 from Michael
   Neuling

 - eeh: Fix wrong argument passed to eeh_rmv_device() from Gavin Shan

 - Initialise pci_io_base as early as possible from Darren Stevens

* tag 'powerpc-4.7-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc: Initialise pci_io_base as early as possible
  powerpc/tm: Avoid SLB faults in treclaim/trecheckpoint when RI=0
  powerpc/eeh: Fix wrong argument passed to eeh_rmv_device()
  powerpc/tm: Always reclaim in start_thread() for exec() class syscalls

Pull drm fixes frlm Dave Airlie:
 "Just some AMD and Intel fixes, the AMD ones are further production
  Polaris fixes, and the Intel ones fix some early timeouts, some PCI ID
  changes and a couple of other fixes.

  Still a bit Internet challenged here, hopefully end of next week will
  solve it"

* tag 'drm-fixes-for-v4.7-rc6' of git://people.freedesktop.org/~airlied/linux:
  drm/i915: Fix missing unlock on error in i915_ppgtt_info()
  drm/amd/powerplay: workaround for UVD clock issue
  drm/amdgpu: add ACLK_CNTL setting for polaris10
  drm/amd/powerplay: fix issue uvd dpm can't enabled on Polaris11.
  drm/amd/powerplay: Workaround for Memory EDC Error on Polaris10.
  drm/i915: Removing PCI IDs that are no longer listed as Kabylake.
  drm/i915: Add more Kabylake PCI IDs.
  drm/i915: Avoid early timeout during AUX transfers
  drm/i915/hsw: Avoid early timeout during LCPLL disable/restore
  drm/i915/lpt: Avoid early timeout during FDI PHY reset
  drm/i915/bxt: Avoid early timeout during PLL enable
  drm/i915: Refresh cached DP port register value on resume
  drm/amd/powerplay: Update CKS on/ CKS off voltage offset calculation
  drm/amd/powerplay: disable FFC.
  drm/amd/powerplay: add some definition for FFC feature on polaris.

Pull spi fixes from Mark Brown:
 "A few small driver-specific fixes for SPI, all in the normal important
  if you hit them category especially the rockchip driver fix which
  addresses a race which has been exposed more frequently with some
  recent performance improvements"

* tag 'spi-fix-v4.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: sunxi: fix transfer timeout
  spi: sun4i: fix FIFO limit
  spi: rockchip: Signal unfinished DMA transfers
  spi: spi-ti-qspi: Suspend the queue before removing the device

Merge tag 'regulator-fix-v4.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator

Pull regulator fixes from Mark Brown:
 "Two small fixes for the regulator subsystem - one fixing a crash with
  one of the devices supported by the max77620 driver, another fixing
  startup for the anatop regulator when it starts up with the regulator
  in bypass mode"

* tag 'regulator-fix-v4.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: max77620: check for valid regulator info
  regulator: anatop: allow regulator to be in bypass mode

Pull clk fixes from Stephen Boyd:
 "A small fix for the newly added oxnas clk driver and a handful of
  rockchip clk driver fixes for newly added rk3399 support"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: Fix return value check in oxnas_stdclk_probe()
  clk: rockchip: release io resource when failing to init clk on rk3399
  clk: rockchip: fix cpuclk registration error handling
  clk: rockchip: Revert "clk: rockchip: reset init state before mmc card initialization"
  clk: rockchip: fix incorrect parent for rk3399's {c,g}pll_aclk_perihp_src
  clk: rockchip: mark rk3399 GIC clocks as critical
  clk: rockchip: initialize flags of clk_init_data in mmc-phase clock

here's a batch of i915 fixes for 4.7.

* tag 'drm-intel-fixes-2016-06-30' of git://anongit.freedesktop.org/drm-intel:
  drm/i915: Fix missing unlock on error in i915_ppgtt_info()
  drm/i915: Removing PCI IDs that are no longer listed as Kabylake.
  drm/i915: Add more Kabylake PCI IDs.
  drm/i915: Avoid early timeout during AUX transfers
  drm/i915/hsw: Avoid early timeout during LCPLL disable/restore
  drm/i915/lpt: Avoid early timeout during FDI PHY reset
  drm/i915/bxt: Avoid early timeout during PLL enable
  drm/i915: Refresh cached DP port register value on resume

Just a few more late fixes for Polaris cards.

* 'drm-fixes-4.7' of git://people.freedesktop.org/~agd5f/linux:
  drm/amd/powerplay: workaround for UVD clock issue
  drm/amdgpu: add ACLK_CNTL setting for polaris10
  drm/amd/powerplay: fix issue uvd dpm can't enabled on Polaris11.
  drm/amd/powerplay: Workaround for Memory EDC Error on Polaris10.
  drm/amd/powerplay: Update CKS on/ CKS off voltage offset calculation
  drm/amd/powerplay: disable FFC.
  drm/amd/powerplay: add some definition for FFC feature on polaris.

The following testcase may result in a page table entries with a invalid
CCA field being generated:

static void *bindstack;

static int sysrqfd;

static void protect_low(int protect)
{
	mprotect(bindstack, BINDSTACK_SIZE, protect);
}

static void sigbus_handler(int signal, siginfo_t * info, void *context)
{
	void *addr = info->si_addr;

	write(sysrqfd, "x", 1);

	printf("sigbus, fault address %p (should not happen, but might)\n",
	       addr);
	abort();
}

static void run_bind_test(void)
{
	unsigned int *p = bindstack;

	p[0] = 0xf001f001;

	write(sysrqfd, "x", 1);

	/* Set trap on access to p[0] */
	protect_low(PROT_NONE);

	write(sysrqfd, "x", 1);

	/* Clear trap on access to p[0] */
	protect_low(PROT_READ | PROT_WRITE | PROT_EXEC);

	write(sysrqfd, "x", 1);

	/* Check the contents of p[0] */
	if (p[0] != 0xf001f001) {
		write(sysrqfd, "x", 1);

		/* Reached, but shouldn't be */
		printf("badness, shouldn't happen but does\n");
		abort();
	}
}

int main(void)
{
	struct sigaction sa;

	sysrqfd = open("/proc/sysrq-trigger", O_WRONLY);

	if (sigprocmask(SIG_BLOCK, NULL, &sa.sa_mask)) {
		perror("sigprocmask");
		return 0;
	}

	sa.sa_sigaction = sigbus_handler;
	sa.sa_flags = SA_SIGINFO | SA_NODEFER | SA_RESTART;
	if (sigaction(SIGBUS, &sa, NULL)) {
		perror("sigaction");
		return 0;
	}

	bindstack = mmap(NULL,
			 BINDSTACK_SIZE,
			 PROT_READ | PROT_WRITE | PROT_EXEC,
			 MAP_PRIVATE | MAP_ANONYMOUS, -1, 0);
	if (bindstack == MAP_FAILED) {
		perror("mmap bindstack");
		return 0;
	}

	printf("bindstack: %p\n", bindstack);

	run_bind_test();

	printf("done\n");

	return 0;
}

There are multiple ingredients for this:

 1) PAGE_NONE is defined to _CACHE_CACHABLE_NONCOHERENT, which is CCA 3
    on all platforms except SB1 where it's CCA 5.
 2) _page_cachable_default must have bits set which are not set
    _CACHE_CACHABLE_NONCOHERENT.
 3) Either the defective version of pte_modify for XPA or the standard
    version must be in used.  However pte_modify for the 36 bit address
    space support is no affected.

In that case additional bits in the final CCA mode may generate an invalid
value for the CCA field.  On the R10000 system where this was tracked
down for example a CCA 7 has been observed, which is Uncached Accelerated.

Fixed by:

 1) Using the proper CCA mode for PAGE_NONE just like for all the other
    PAGE_* pte/pmd bits.
 2) Fix the two affected variants of pte_modify.

Further code inspection also shows the same issue to exist in pmd_modify
which would affect huge page systems.

Issue in pte_modify tracked down by Alastair Bridgewater, PAGE_NONE
and pmd_modify issue found by me.

The history of this goes back beyond Linus' git history.  Chris Dearman's
commit 35133692 ("[MIPS] Allow setting of
the cache attribute at run time.") missed the opportunity to fix this
but it was originally introduced in lmo commit
d523832cf12007b3242e50bb77d0c9e63e0b6518 ("Missing from last commit.")
and 32cc38229ac7538f2346918a09e75413e8861f87 ("New configuration option
CONFIG_MIPS_UNCACHED.")
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Alastair Bridgewater <alastair.bridgewater@gmail.com>

Pull ACPI fix from Rafael Wysocki:
 "Fix an expression in the ACPI PCI IRQ management code added by a
  recent commit that overlooked missing parens in it, so the result of
  the computation is incorrect in some cases (Sinan Kaya)"

* tag 'acpi-4.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI,PCI,IRQ: correct operator precedence

Pull power management fixes from Rafael Wysocki:
 "Three cpufreq fixes, one in the core (stable-candidate) and two in
  drivers (intel_pstate and cpufreq-dt).

  Specifics:

   - Fix a recent intel_pstate regression that caused the number of
     wakeups to increase significantly on an idle system in some cases
     due to excessive synchronize_sched() invocations (Rafael Wysocki).

   - Fix unnecessary invocations of WARN_ON() in the cpufreq core after
     cpufreq has been suspended introduced during the 4.6 cycla (Rafael
     Wysocki).

   - Fix an error code path in the cpufreq-dt-platdev driver that
     forgets to drop a reference to a DT node (Masahiro Yamada)"

* tag 'pm-4.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: Avoid false-positive WARN_ON()s in cpufreq_update_policy()
  cpufreq: dt: call of_node_put() before error out
  intel_pstate: Do not clear utilization update hooks on policy changes

Pull vfs fixes from Al Viro:
 "Tmpfs readdir throughput regression fix (this cycle) + some -stable
  fodder all over the place.

  One missing bit is Miklos' tonight locks.c fix - NFS folks had already
  grabbed that one by the time I woke up ;-)"

[ The locks.c fix came through the nfsd tree just moments ago ]

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  namespace: update event counter when umounting a deleted dentry
  9p: use file_dentry()
  ceph: fix d_obtain_alias() misuses
  lockless next_positive()
  libfs.c: new helper - next_positive()
  dcache_{readdir,dir_lseek}(): don't bother with nested ->d_lock

Pull lockd/locks fixes from Bruce Fields:
 "One fix for lockd soft lookups in an error path, and one fix for file
  leases on overlayfs"

* tag 'nfsd-4.7-3' of git://linux-nfs.org/~bfields/linux:
  locks: use file_inode()
  lockd: unregister notifier blocks if the service fails to come up completely

Pull more MFD fixes from Lee Jones:
 "Apologies for missing these from the first pull request.

  Final patches fixing Reset API change"

* tag 'mfd-fixes-4.7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
  usb: dwc3: st: Use explicit reset_control_get_exclusive() API
  phy: phy-stih407-usb: Use explicit reset_control_get_exclusive() API
  phy: miphy28lp: Inform the reset framework that our reset line may be shared

Pull libnvdimm fixes from Dan Williams:
 "1/ Two regression fixes since v4.6: one for the byte order of a sysfs
     attribute (bz121161) and another for QEMU 2.6's NVDIMM _DSM (ACPI
     Device Specific Method) implementation that gets tripped up by new
     auto-probing behavior in the NFIT driver.

  2/ A fix tagged for -stable that stops the kernel from
     clobbering/ignoring changes to the configuration of a 'pfn'
     instance ("struct page" driver).  For example changing the
     alignment from 2M to 1G may silently revert to 2M if that value is
     currently stored on media.

  3/ A fix from Eric for an xfstests failure in dax.  It is not
     currently tagged for -stable since it requires an 8-exabyte file
     system to trigger, and there appear to be no user visible side
     effects"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  nfit: fix format interface code byte order
  dax: fix offset overflow in dax_io
  acpi, nfit: fix acpi_check_dsm() vs zero functions implemented
  libnvdimm, pfn, dax: fix initialization vs autodetect for mode + alignment

Pull staging and IIO fixes from Greg KH:
 "Here are a few small staging and iio driver fixes for 4.7-rc6.

  Nothing major here, just a number of small fixes, all have been in
  linux-next for a while, and the full details are in the shortlog"

* tag 'staging-4.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  iio:ad7266: Fix probe deferral for vref
  iio:ad7266: Fix support for optional regulators
  iio:ad7266: Fix broken regulator error handling
  iio: accel: kxsd9: fix the usage of spi_w8r8()
  staging: iio: accel: fix error check
  staging: iio: ad5933: fix order of cycle conditions
  staging: iio: fix ad7606_spi regression
  iio: inv_mpu6050: Fix use-after-free in ACPI code

Pull tty fixes from Greg KH:
 "Here are two tty fixes for some reported issues.  One resolves a crash
  in devpts, and the other resolves a problem with the fbcon cursor
  blink causing lockups.

  Both have been in linux-next with no reported problems"

* tag 'tty-4.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  devpts: fix null pointer dereference on failed memory allocation
  tty: vt: Fix soft lockup in fbcon cursor blink timer.

Pull USB and PHY fixes from Greg KH:
 "Here are a number of small USB and PHY driver fixes for 4.7-rc6.

  Nothing major here, all are described in the shortlog below.  All have
  been in linux-next with no reported issues"

* tag 'usb-4.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: don't free bandwidth_mutex too early
  USB: EHCI: declare hostpc register as zero-length array
  phy-sun4i-usb: Fix irq free conditions to match request conditions
  phy: bcm-ns-usb2: checking the wrong variable
  phy-sun4i-usb: fix missing __iomem *
  phy: phy-sun4i-usb: Fix optional gpios failing probe
  phy: rockchip-dp: fix return value check in rockchip_dp_phy_probe()
  phy: rcar-gen3-usb2: fix unexpected repeat interrupts of VBUS change
  usb: common: otg-fsm: add license to usb-otg-fsm

Pull IOMMU fixes from Joerg Roedel:
 "Three fixes:

   - Fix use of smp_processor_id() in preemptible code in the IOVA
     allocation code.  This got introduced with the scalability
     improvements in this release cycle.

   - A VT-d fix for out-of-bounds access of the iommu->domains array.
     The bug showed during suspend/resume.

   - AMD IOMMU fix to print the correct device id in the ACPI parsing
     code"

* tag 'iommu-fixes-v4.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/amd: Initialize devid variable before using it
  iommu/vt-d: Fix overflow of iommu->domains array
  iommu/iova: Disable preemption around use of this_cpu_ptr()

Merge remote-tracking branches 'regulator/fix/anatop' and 'regulator/fix/max77620' into regulator-linus

(Another one for the f_path debacle.)

ltp fcntl33 testcase caused an Oops in selinux_file_send_sigiotask.

The reason is that generic_add_lease() used filp->f_path.dentry->inode
while all the others use file_inode().  This makes a difference for files
opened on overlayfs since the former will point to the overlay inode the
latter to the underlying inode.

So generic_add_lease() added the lease to the overlay inode and
generic_delete_lease() removed it from the underlying inode.  When the file
was released the lease remained on the overlay inode's lock list, resulting
in use after free.
Reported-by: Eryu Guan <eguan@redhat.com>
Fixes: 4bacc9c9 ("overlayfs: Make f_path always point to the overlay and f_inode to the underlay")
Cc: <stable@vger.kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>

We're making all reset line users specify whether their lines are
shared with other IP or they operate them exclusively.  In this case
the line is exclusively used only by this IP, so use the *_exclusive()
API accordingly.
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

We're making all reset line users specify whether their lines are
shared with other IP or they operate them exclusively.  In this case
the line is exclusively used only by this IP, so use the *_exclusive()
API accordingly.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

On the STiH410 B2120 development board the MiPHY28lp shares its reset
line with the Synopsys DWC3 SuperSpeed (SS) USB 3.0 Dual-Role-Device
(DRD).  New functionality in the reset subsystems forces consumers to
be explicit when requesting shared/exclusive reset lines.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

- m_start() in fs/namespace.c expects that ns->event is incremented each
  time a mount added or removed from ns->list.
- umount_tree() removes items from the list but does not increment event
  counter, expecting that it's done before the function is called.
- There are some codepaths that call umount_tree() without updating
  "event" counter. e.g. from __detach_mounts().
- When this happens m_start may reuse a cached mount structure that no
  longer belongs to ns->list (i.e. use after free which usually leads
  to infinite loop).

This change fixes the above problem by incrementing global event counter
before invoking umount_tree().

Change-Id: I622c8e84dcb9fb63542372c5dbf0178ee86bb589
Cc: stable@vger.kernel.org
Signed-off-by: Andrey Ulanov <andreyu@google.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

v9fs may be used as lower layer of overlayfs and accessing f_path.dentry
can lead to a crash.  In this case it's a NULL pointer dereference in
p9_fid_create().

Fix by replacing direct access of file->f_path.dentry with the
file_dentry() accessor, which will always return a native object.
Reported-by: Alessio Igor Bogani <alessioigorbogani@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Tested-by: Alessio Igor Bogani <alessioigorbogani@gmail.com>
Fixes: 4bacc9c9 ("overlayfs: Make f_path always point to the overlay and f_inode to the underlay")
Cc: <stable@vger.kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

If the lockd service fails to start up then we need to be sure that the
notifier blocks are not registered, otherwise a subsequent start of the
service could cause the same notifier to be registered twice, leading to
soft lockups.
Signed-off-by: Scott Mayhew <smayhew@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 0751ddf7 "lockd: Register callbacks on the inetaddr_chain..."
Signed-off-by: J. Bruce Fields <bfields@redhat.com>

Pull KVM fixes from Paolo Bonzini:
 "ARM and x86 fixes"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: nVMX: VMX instructions: fix segment checks when L1 is in long mode.
  KVM: LAPIC: cap __delay at lapic_timer_advance_ns
  KVM: x86: move nsec_to_cycles from x86.c to x86.h
  pvclock: Get rid of __pvclock_read_cycles in function pvclock_read_flags
  pvclock: Cleanup to remove function pvclock_get_nsec_offset
  pvclock: Add CPU barriers to get correct version value
  KVM: arm/arm64: Stop leaking vcpu pid references
  arm64: KVM: fix build with CONFIG_ARM_PMU disabled

Pull ARC fix from Vineet Gupta:
 "Reinstate dwarf unwinder/loadable-modules with new gnu tools"

* tag 'arc-4.7-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  arc: unwind: warn only once if DW2_UNWIND is disabled
  ARC: unwind: ensure that .debug_frame is generated (vs. .eh_frame)