- 27 Oct, 2009 40 commits
-
-
John W. Linville authored
Replace netif_tx_{start,stop,wake}_all_queues with the single-queue equivalents (i.e. netif_{start,stop,wake}_queue). Since we are down to a single queue, these should peform slightly better. Signed-off-by:John W. Linville <linville@tuxdriver.com>
-
Bob Copeland authored
This updates ath5k to calibrate the noise floor similar to the way it is done in the madwifi hal and ath9k. Of note: - we start NF measurement at the same time as AGC calibration, but do not actually read the value until the periodic (long) calibration - we keep a history of the last few values read and write the median back to the hardware for CCA - we do not complain if NF calibration isn't complete, instead we keep the last read value. Signed-off-by:
Bob Copeland <me@bobcopeland.com> Acked-by:
Nick Kossifidis <mickflemm@gmail.com> Signed-off-by:
-
Marek Lindner authored
Signed-off-by:
Marek Lindner <lindner_marek@yahoo.de> Signed-off-by:
-
Holger Schurig authored
This function will be needed for the cfg80211-enabled libertas driver. Signed-off-by:
Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by:
-
Kalle Valo authored
During rename of the driver from wl12xx to wl1251 the spi device name was accidentally left as wl12xx. Rename it to wl1251 which is the proper name of the driver. Signed-off-by:
Kalle Valo <kalle.valo@nokia.com> Signed-off-by:
-
Holger Schurig authored
It might be the case that __cfg80211_disconnected() has already cleaned up wdev->current_bss() for us. The old code didn't catch that situation and didn't warn needlessly. Signed-off-by:
-
Holger Schurig authored
Get rid of cookies in cfg80211_send_XXX() functions. Signed-off-by:
-
Juuso Oikarinen authored
Fix the filter configuration to properly work with the two phase filter configuration (prepare_multicast/configure_filter.) Signed-off-by:
Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by:
Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by:
-
Luciano Coelho authored
We cannot be in PS mode when running PLT tests, so we need to make sure we're in active mode. Also, we need to clear up the rx_counter when we stop PLT, otherwise it could cause problems when entering PLT again. Signed-off-by:
-
Juuso Oikarinen authored
Several memory allocation related failure cases were not properly handled by the driver - the result was that in low memory conditions booting of a corrupted FW could be attempted - and user space would not get proper failure code. Signed-off-by:
-
Juuso Oikarinen authored
Remove unnecessary RX descriptor memory allocation from the driver. The allocation was a remnant of the wl1251 driver. Signed-off-by:
-
Juuso Oikarinen authored
Add support for IPv4 ARP filtering in the driver. This will dramatically reduce the number of unnecessary interrupts by the device in conqested networks. This patch is based on a similar patch to wl1251 by Janne Ylälehto. Cc: Janne Ylälehto <janne.ylalehto@nokia.com> Signed-off-by:
-
Juuso Oikarinen authored
The event handling mechanism could miss events if multiple events would occur simultaneously. Fix event handling mechanism to process all events. Signed-off-by:
-
Juuso Oikarinen authored
Fixes bugs in the multicast list handling: - Use atomic memory allocation in non-sleepable context - Increment address pointer when iterating list of MC addresses Signed-off-by:
-
Teemu Paasikivi authored
Fixed checking of status of the received packet. On wl1251 status is in the flags field of the descriptor, on wl1271 there is a separate status field. Signed-off-by:
Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Reviewed-by:
-
Teemu Paasikivi authored
Added support to assiociate and use connection on 5 GHz band (802.11a). Signed-off-by:
-
Teemu Paasikivi authored
Added support to scan 802.11a access points on 5 GHz band when using wl1273 chip. Signed-off-by:
-
Teemu Paasikivi authored
Added checking of whether channel is enabled or disabled by mac80211 stack to scan. Disabled channels are not scanned. Signed-off-by:
-
Teemu Paasikivi authored
Added data rate and frequency tables for 5 GHz band channels, 5 GHz radio configration parameters and configuration option to enable 802.11 support. Signed-off-by:
-
Juuso Oikarinen authored
Remove busy-word checking to work around an SPI bug. To reduce the chance of chipset-busy scenarios, increment the number of fixed busy words. Signed-off-by:
-
Juuso Oikarinen authored
Add support to enable beacon early termination in the firmware. Early Beacon termination is a feature which allows the radio to be turned off after TIM IE to save power. Signed-off-by:
-
Juuso Oikarinen authored
Disable IRQ's after FW initialization failure - originally this was not done in all cases, and it resulted in a kernel warning if firmware initialization was tried again without reboot. Signed-off-by:
-
Juuso Oikarinen authored
Move the default FW config into a module global static variable, instead of being a stack variable. Signed-off-by:
-
Juuso Oikarinen authored
Add a configuration structure for RX path parameters, and set default configuration values there. Signed-off-by:
-
Juuso Oikarinen authored
Add a configuration structure for connection management parameters, and set default configuration values there. Signed-off-by:
-
Juuso Oikarinen authored
Add a configuration structure for TX path parameters, and set defalt configuration values there. Signed-off-by:
-
Juuso Oikarinen authored
Add a configuration structure for RX path parameters, and set default configuration values there. Signed-off-by:
-
Juuso Oikarinen authored
In order to make the firmware configuration more manageable, collect hardcoded configuration values into one data structure, and set default values there. Add the SoftGemini BT/WLAN coex paramters into the config structure. Signed-off-by:
-
Juuso Oikarinen authored
If the 38.4MHz reference clock is configured to the firmware, it crashes on boot. Configuring an experimental 38.4MHz in XTAL mode allows the firmware to boot, and everything appears to work. Signed-off-by:
-
Zhu Yi authored
This switches the iwlwifi driver to use paged skb from linear skb for Rx buffer. So that it relieves some Rx buffer allocation pressure for the memory subsystem. Currently iwlwifi (4K for 3945) requests 8K bytes for Rx buffer. Due to the trailing skb_shared_info in the skb->data, alloc_skb() will do the next order allocation, which is 16K bytes. This is suboptimal and more likely to fail when the system is under memory usage pressure. Switching to paged Rx skb lets us allocate the RXB directly by alloc_pages(), so that only order 1 allocation is required. It also adjusts the area spin_lock (with IRQ disabled) protected in the tasklet because tasklet guarentees to run only on one CPU and the new unprotected code can be preempted by the IRQ handler. This saves us from spawning another workqueue to make skb_linearize/__pskb_pull_tail happy (which cannot be called in hard irq context). Finally, mac80211 doesn't support paged Rx yet. So we linearize the skb for all the management frames and software decryption or defragmentation required data frames before handed to mac80211. For all the other frames, we __pskb_pull_tail 64 bytes in the linear area of the skb for mac80211 to handle them properly. Signed-off-by:
Zhu Yi <yi.zhu@intel.com> Signed-off-by:
-
Luciano Coelho authored
We were using the join command to change some settings when the stack asked us to do it. In many cases they were not needed (and could cause potential problems), so they were removed. In other cases there are ACX commands that can be used instead of using join to reconfigure. Signed-off-by:
-
Luciano Coelho authored
We shouldn't use a join command to change the filter settings while associated. The right way to do it is to use ACX_RX_CFG. Signed-off-by:
-
Juuso Oikarinen authored
Update the magic values of the wl1271 boot time config according to the new reference driver. Signed-off-by:
-
Juuso Oikarinen authored
With the change to the new firmware, there was a change to firmware memory partitioning. Along with that change, the translation of all partitions was unified, and separate functions for reg and mem access became unnecessary. Cleanup the unnecessary functions. Signed-off-by:
-
Juuso Oikarinen authored
Update the TX path block calculation algorithm based on TI reference. Signed-off-by:
-
Juuso Oikarinen authored
Enable and configure smart reflex. This should have a reducing impact on power consumption. Signed-off-by:
-
Juuso Oikarinen authored
The new firmware has fixed a firmware crash problem related to ELP entry. Enable ELP to conserve power. Signed-off-by:
-
Juuso Oikarinen authored
Remove separate interrupt register reading from the interrupt handling routine. This will slightly improve interrupt performance. Signed-off-by:
-
Juuso Oikarinen authored
Updated RefClk configuration based on reference sources. Apparently this change will improve RF performance. Signed-off-by:
-
Juuso Oikarinen authored
Add top register access function. Signed-off-by:
-
