- 15 May, 2018 17 commits
-
-
Alexandre Belloni authored
Add a driver for the Microsemi MII Management controller (MIIM) found on Microsemi SoCs. On Ocelot, there are two controllers, one is connected to the internal PHYs, the other one can communicate with external PHYs. Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
Alexandre Belloni <alexandre.belloni@bootlin.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Alexandre Belloni authored
DT bindings for the Microsemi MII Management Controller found on Microsemi SoCs Reviewed-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
David S. Miller authored
Marcelo Ricardo Leitner says: ==================== sctp: Introduce sctp_flush_ctx This struct will hold all the context used during the outq flush, so we don't have to pass lots of pointers all around. Checked on x86_64, the compiler inlines all these functions and there is no derreference added because of the struct. This patchset depends on 'sctp: refactor sctp_outq_flush' Changes since v1: - updated to build on top of v2 of 'sctp: refactor sctp_outq_flush' Changes since v2: - fixed a rebase issue which reverted a change in patch 2. - rebased on v3 of 'sctp: refactor sctp_outq_flush' ==================== Signed-off-by: -
Marcelo Ricardo Leitner authored
A collection of fixups from previous patches, left for later to not introduce unnecessary changes while moving code around. Signed-off-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
-
Marcelo Ricardo Leitner authored
Pre-compute these so the compiler won't reload them (due to no-strict-aliasing). Changes since v2: - Do not replace a return with a break in sctp_outq_flush_data Signed-off-by:
-
Marcelo Ricardo Leitner authored
With this struct we avoid passing lots of variables around and taking care of updating the current transport/packet. Signed-off-by:
-
David S. Miller authored
Marcelo Ricardo Leitner says: ==================== sctp: refactor sctp_outq_flush Currently sctp_outq_flush does many different things and arguably unrelated, such as doing transport selection and outq dequeueing. This patchset refactors it into smaller and more dedicated functions. The end behavior should be the same. The next patchset will rework the function parameters. Changes since v1: - fix build issues on patches 3 and 4, and updated 5 and 8 because of it. Changes since v2: - fixed panic if building with just up to patch 3 applied ==================== Signed-off-by: -
Marcelo Ricardo Leitner authored
Remove an inner one, which tended to be error prone due to the cascading and it can be replaced by a simple if (). Rework the outer one so that the actual flush code is not inside it. Now we first validate if we can or cannot send data, return if not, and then the flush code. Suggested-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
Marcelo Ricardo Leitner authored
Retransmissions may be triggered when in user context, so lets make use of gfp. Signed-off-by:
-
Marcelo Ricardo Leitner authored
To the new sctp_outq_flush_transports. Comment on Nagle is outdated and removed. Nagle is performed earlier, while checking if the chunk fits the packet: if the outq length is not enough to fill the packet, it returns SCTP_XMIT_DELAY. So by when it gets to sctp_outq_flush_transports, it has to go through all enlisted transports. Signed-off-by:
-
Marcelo Ricardo Leitner authored
To the new sctp_outq_flush_data. Again, smaller functions and with well defined objectives. Signed-off-by:
-
Marcelo Ricardo Leitner authored
This patch renames current sctp_outq_flush_rtx to __sctp_outq_flush_rtx and create a new sctp_outq_flush_rtx, with the code that was on sctp_outq_flush. Again, the idea is to have functions with small and defined objectives. Yes, there is an open-coded path selection in the now sctp_outq_flush_rtx. That is kept as is for now because it may be very different when we implement retransmission path selection algorithms for CMT-SCTP. Signed-off-by:
-
Marcelo Ricardo Leitner authored
Named sctp_outq_flush_ctrl and, with that, keep the contexts contained. One small fix embedded is the reset of one_packet at every iteration. This allows bundling of some control chunks in case they were preceeded by another control chunk that cannot be bundled. Other than this, it has the same behavior. Changes since v2: - Fixed panic reported by kbuild test robot if building with only up to this patch applied, due to bad parameter to sctp_outq_select_transport and by not initializing packet after calling sctp_outq_flush_ctrl. Signed-off-by:
-
Marcelo Ricardo Leitner authored
We had two spots doing such complex operation and they were very close to each other, a bit more tailored to here or there. This patch unifies these under the same function, sctp_outq_select_transport, which knows how to handle control chunks and original transmissions (but not retransmissions). Signed-off-by:
-
Marcelo Ricardo Leitner authored
Factor out the code for generating singletons. It's used only once, but helps to keep the context contained. The const variables are to ease the reading of subsequent calls in there. Signed-off-by:
-
Kumar Sanghvi authored
Adds support for matching flows based on tunnel VNI value. Introduces fw APIs for allocating/removing MPS entries related to encapsulation. And uses the same while adding/deleting filters for offloading flows based on tunnel VNI match. Signed-off-by:
Kumar Sanghvi <kumaras@chelsio.com> Signed-off-by:
Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by:
-
Jose Abreu authored
I'm offering to be a co-maintainer for stmmac driver. As per discussion with Alexandre, I will arrange to get STM32 boards to test patches in GMAC version 3.x and 4.1. I also have HW to test GMAC version 5. Looking forward to contribute to net-dev! Signed-off-by:
Jose Abreu <joabreu@synopsys.com> Cc: David S. Miller <davem@davemloft.net> Cc: Joao Pinto <jpinto@synopsys.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Acked-by:
Alexandre TORGUE <alexandre.torgue@st.com> Signed-off-by:
-
- 14 May, 2018 23 commits
-
-
Arjun Vynipadath authored
We no longer require a check for cxgb4 to be MASTER when configuring SRIOV, It was required when we had module parameter to instantiate vf. Signed-off-by:
Arjun Vynipadath <arjun@chelsio.com> Signed-off-by:
Casey Leedom <leedom@chelsio.com> Signed-off-by:
-
Petr Machata authored
When resolving a path that the packet will take after being encapsulated in mirror-to-gretap scenarios, one of the devices en route could be a LAG. In that case, mirror to first up slave that corresponds to a front panel port. Signed-off-by:
Petr Machata <petrm@mellanox.com> Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
-
Hernán Gonzalez authored
Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(...)). drivers/net/ethernet/ti/cpts.c:567:9-16: WARNING: ERR_CAST can be used with cpts->refclk Generated by: scripts/coccinelle/api/err_cast.cocci Signed-off-by:
Hernán Gonzalez <hernan@vanguardiasur.com.ar> Signed-off-by:
-
Marcelo Ricardo Leitner authored
Currently, when the rule is not to be exclusively executed by the hardware, extack is not passed along and offloading failures don't get logged. The idea was that hardware failures are okay because the rule will get executed in software then and this way it doesn't confuse unware users. But this is not helpful in case one needs to understand why a certain rule failed to get offloaded. Considering it may have been a temporary failure, like resources exceeded or so, reproducing it later and knowing that it is triggering the same reason may be challenging. The ultimate goal is to improve Open vSwitch debuggability when using flower offloading. This patch adds a new flag to enable verbose logging. With the flag set, extack will be passed to the driver, which will be able to log the error. As the operation itself probably won't fail (not because of this, at least), current iproute will already log it as a Warning. The flag is generic, so it can be reused later. No need to restrict it just for HW offloading. The command line will follow the syntax that tc-ebpf already uses, tc ... [ verbose ] ... , and extend its meaning. For example: # ./tc qdisc add dev p7p1 ingress # ./tc filter add dev p7p1 parent ffff: protocol ip prio 1 \ flower verbose \ src_mac ed:13:db:00:00:00 dst_mac 01:80:c2:00:00:d0 \ src_ip 56.0.0.0 dst_ip 55.0.0.0 action drop Warning: TC offload is disabled on net device. # echo $? 0 # ./tc filter add dev p7p1 parent ffff: protocol ip prio 1 \ flower \ src_mac ff:13:db:00:00:00 dst_mac 01:80:c2:00:00:d0 \ src_ip 56.0.0.0 dst_ip 55.0.0.0 action drop # echo $? 0 Signed-off-by:
-
David S. Miller authored
Chen-Yu Tsai says: ==================== net: stmmac: dwmac-sun8i: Support R40 This is a resend of the patches for net-next split out from my R40 Ethernet support v2 series, as requested by David Miller. The arm-soc bits will follow, once I rework the A64 system controller compatible. Patches 1, 2, and 3 clean up the dwmac-sun8i binding. Patch 4 adds device tree binding for Allwinner R40's Ethernet controller. Patch 5 converts regmap access of the syscon region in the dwmac-sun8i driver to regmap_field, in anticipation of different field widths on the R40. Patch 6 introduces custom plumbing in the dwmac-sun8i driver to fetch a regmap from another device, by looking up said device via a phandle, then getting the regmap associated with that device. Patch 7 adds support for different or absent TX/RX delay chain ranges to the dwmac-sun8i driver. Patch 8 adds support for the R40's ethernet controller. Excerpt from original cover letter: Changes since v1: - Default to fetching regmap from device pointed to by syscon phandle, and falling back to syscon API if that fails. - Dropped .syscon_from_dev field in device data as a result of the previous change. - Added a large comment block explaining the first change. - Simplified description of syscon property in sun8i-dwmac binding. - Regmap now only exposes the EMAC/GMAC register, but retains the offset within its address space. - Added patches for A64, which reuse the same sun8i-dwmac changes. This series adds support for the DWMAC based Ethernet controller found on the Allwinner R40 SoC. The controller is either a DWMAC clone or DWMAC core with its registers rearranged. This is already supported by the dwmac-sun8i driver. The glue layer control registers, unlike other sun8i family SoCs, is not in the system controller region, but in the clock control unit, like with the older A20 and A31 SoCs. While we reuse the bindings for dwmac-sun8i using a syscon phandle reference, we need some custom plumbing for the clock driver to export a regmap that only allows access to the GMAC register to the dwmac-sun8i driver. An alternative would be to allow drivers to register custom syscon devices with their own regmap and locking. ==================== Signed-off-by: -
Chen-Yu Tsai authored
The Allwinner R40 SoC has the EMAC controller supported by dwmac-sun8i. It is named "GMAC", while EMAC refers to the 10/100 Mbps Ethernet controller supported by sun4i-emac. The controller is the same, but the R40 has the glue layer controls in the clock control unit (CCU), with a reduced RX delay chain, and no TX delay chain. This patch adds support for it using the framework laid out by previous patches to map the differences. Signed-off-by:
Chen-Yu Tsai <wens@csie.org> Acked-by:
Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by:
-
Chen-Yu Tsai authored
On the R40 SoC, the RX delay chain only has a range of 0~7 (hundred picoseconds), instead of 0~31. Also the TX delay chain is completely absent. This patch adds support for different ranges by adding per-compatible maximum values in the variant data. A maximum of 0 indicates that the delay chain is not supported or absent. Signed-off-by:
-
Chen-Yu Tsai authored
On the Allwinner R40 SoC, the "GMAC clock" register is in the CCU address space. Using a standard syscon to access it provides no coordination with the CCU driver for register access. Neither does it prevent this and other drivers from accessing other, maybe critical, clock control registers. On other SoCs, the register is in the "system control" address space, which might also contain controls for mapping SRAM to devices or the CPU. This hardware has the same issues. Instead, for these types of setups, we let the device containing the control register create a regmap tied to it. We can then get the device from the existing syscon phandle, and retrieve the regmap with dev_get_regmap(). Signed-off-by:
-
Chen-Yu Tsai authored
On the Allwinner R40, the "GMAC clock" register is located in the CCU block, at a different register address than the other SoCs that have it in the "system control" block. This patch converts the use of regmap to regmap_field for mapping and accessing the syscon register, so we can have the register address in the variants data, and not in the actual register manipulation code. This patch only converts regmap_read() and regmap_write() calls to regmap_field_read() and regmap_field_write() calls. There are some places where it might make sense to switch to regmap_field_update_bits(), but this is not done here to keep the patch simple. Signed-off-by:
-
Chen-Yu Tsai authored
The Allwinner R40 SoC has the EMAC controller supported by dwmac-sun8i. It is named "GMAC", while EMAC refers to the 10/100 Mbps Ethernet controller supported by sun4i-emac. The controller is the same, but the R40 has the glue layer controls in the clock control unit (CCU), with a reduced RX delay chain, and no TX delay chain. This patch adds the R40 specific bits to the dwmac-sun8i binding. Signed-off-by:
-
Chen-Yu Tsai authored
The syscon property is used to point to the device that holds the glue layer control register known as the "EMAC (or GMAC) clock register". We do not need to explicitly list what compatible strings are needed, as this information is readily available in the user manuals. Also the "syscon" device type is more of an implementation detail. There are many ways to access a register not in a device's address range, the syscon interface being the most generic and unrestricted one. Simplify the description so that it says what it is supposed to describe. Signed-off-by:
-
Chen-Yu Tsai authored
The A83T syscon compatible was appended to the syscon compatibles list, instead of inserted in to preserve the ordering. Move it to the proper place to keep the list sorted. Signed-off-by:
-
Chen-Yu Tsai authored
The clock delay chains found in the glue layer for dwmac-sun8i are only used with RGMII PHYs. They are not intended for non-RGMII PHYs, such as MII external PHYs or the internal PHY. Also, a recent SoC has a smaller range of possible values for the delay chain. This patch reformats the delay chain section of the device tree binding to make it clear that the delay chains only apply to RGMII PHYs, and make it easier to add the R40-specific bits later. Signed-off-by:
-
David S. Miller authored
Vivien Didelot says: ==================== net: dsa: mv88e6xxx: remove Global 1 setup The mv88e6xxx driver is still writing arbitrary registers at setup time, e.g. priority override bits. Add ops for them and provide specific setup functions for priority and stats before getting rid of the erroneous mv88e6xxx_g1_setup code, as previously done with Global 2. ==================== Signed-off-by: -
Vivien Didelot authored
Now that the Global 1 specific setup function only setup the statistics unit, kill it in favor of a mv88e6xxx_stats_setup function. Signed-off-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by:
-
Vivien Didelot authored
All Marvell switch families except 88E6390 have direct registers in Global 1 for IEEE and IP priorities override mapping. The 88E6390 uses indirect tables instead. Add .ieee_pri_map and .ip_pri_map ops to distinct that and call them from a mv88e6xxx_pri_setup helper. Only non-6390 are concerned ATM. Signed-off-by:
-
Vivien Didelot authored
The Marvell 88E6390 model has its histogram mode bits moved in the Global 1 Control 2 register. Use the previously introduced mv88e6xxx_g1_ctl2_mask helper to set them. At the same time complete the documentation of the said register. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller authored
Jeff Kirsher says: ==================== 40GbE Intel Wired LAN Driver Updates 2018-05-14 This series contains updates to virtchnl, i40e and i40evf. Bruce cleans up whitespace and unnecessary parentheses in virtchnl. Jake does a number of stat cleanups in the i40e driver, including cleanup of code indentation, whitespace issues, remove duplicate stats, fix grammar in code comment and general spring cleaning of the statistics code. Patryk fixes an issue where we recalculate vectors left and vectors wanted but do not take into account the reduced number of queue pairs per VSI. Harshitha adds tx_busy stat to ethtool stats to track the number of times we return NETDEV_TX_BUSY to the stack during transmit. Paweł fixes a potential system crash when unloading the VF driver after a hardware reset. ==================== Signed-off-by: -
David S. Miller authored
Rahul Lakkireddy says: ==================== kernel: add support to collect hardware logs in crash recovery kernel On production servers running variety of workloads over time, kernel panic can happen sporadically after days or even months. It is important to collect as much debug logs as possible to root cause and fix the problem, that may not be easy to reproduce. Snapshot of underlying hardware/firmware state (like register dump, firmware logs, adapter memory, etc.), at the time of kernel panic will be very helpful while debugging the culprit device driver. This series of patches add new generic framework that enable device drivers to collect device specific snapshot of the hardware/firmware state of the underlying device in the crash recovery kernel. In crash recovery kernel, the collected logs are added as elf notes to /proc/vmcore, which is copied by user space scripts for post-analysis. The sequence of actions done by device drivers to append their device specific hardware/firmware logs to /proc/vmcore are as follows: 1. During probe (before hardware is initialized), device drivers register to the vmcore module (via vmcore_add_device_dump()), with callback function, along with buffer size and log name needed for firmware/hardware log collection. 2. vmcore module allocates the buffer with requested size. It adds an elf note and invokes the device driver's registered callback function. 3. Device driver collects all hardware/firmware logs into the buffer and returns control back to vmcore module. The device specific hardware/firmware logs can be seen as elf notes with note type 0x700, as shown below: Displaying notes found at file offset 0x00001000 with length 0x040032c0: Owner Data size Description LINUX 0x02000fec Unknown note type: (0x00000700) LINUX 0x02000fec Unknown note type: (0x00000700) CORE 0x00000150 NT_PRSTATUS (prstatus structure) CORE 0x00000150 NT_PRSTATUS (prstatus structure) CORE 0x00000150 NT_PRSTATUS (prstatus structure) CORE 0x00000150 NT_PRSTATUS (prstatus structure) CORE 0x00000150 NT_PRSTATUS (prstatus structure) CORE 0x00000150 NT_PRSTATUS (prstatus structure) CORE 0x00000150 NT_PRSTATUS (prstatus structure) CORE 0x00000150 NT_PRSTATUS (prstatus structure) VMCOREINFO 0x00000785 Unknown note type: (0x00000000) Patch 1 adds API to vmcore module to allow drivers to register callback to collect the device specific hardware/firmware logs. The logs will be added to /proc/vmcore as elf notes. Patch 2 updates read and mmap logic to append device specific hardware/ firmware logs as elf notes. Patch 3 shows a cxgb4 driver example using the API to collect hardware/firmware logs in crash recovery kernel, before hardware is initialized. Thanks, Rahul --- v8: - Added missing linux/types.h header include. - Removed __vmcore_add_device_dump(). v7: - Removed "CHELSIO" vendor identifier in Elf Note name. Instead, writing "LINUX". - Moved vmcoredd_header to new file include/uapi/linux/vmcore.h - Reworked vmcoredd_header to include Elf Note as part of the header itself. - Removed vmcoredd_get_note_size(). - Renamed vmcoredd_write_note() to vmcoredd_write_header(). - Replaced all "unsigned long" with "unsigned int" for device dump size since max size of Elf Word is u32. v6: - Reworked device dump elf note name to contain vendor identifier. - Added vmcoredd_header that precedes actual dump in the Elf Note. - Device dump's name is moved inside vmcoredd_header. - Added "CHELSIO" string as vendor identifier in the Elf Note name for cxgb4 device dumps. v5: - Removed enabling CONFIG_PROC_VMCORE_DEVICE_DUMP by default and updated help message. v4: - Made __vmcore_add_device_dump() static. - Moved compile check to define vmcore_add_device_dump() to crash_dump.h to fix compilation when vmcore.c is not compiled in. - Convert ---help--- to help in Kconfig as indicated by checkpatch. - Rebased to tip. v3: - Dropped sysfs crashdd module. - Exported dumps as elf notes. Suggested by Eric Biederman <ebiederm@xmission.com>. Added as patch 2 in this version. - Added CONFIG_PROC_VMCORE_DEVICE_DUMP to allow configuring device dump support. - Moved logic related to adding dumps from crashdd to vmcore module. - Rename all crashdd* to vmcoredd*. - Updated comments. v2: - Added ABI Documentation for crashdd. - Directly use octal permission instead of macro. Changes since rfc v2: - Moved exporting crashdd from procfs to sysfs. Suggested by Stephen Hemminger <stephen@networkplumber.org> - Moved code from fs/proc/crashdd.c to fs/crashdd/ directory. - Replaced all proc API with sysfs API and updated comments. - Calling driver callback before creating the binary file under crashdd sysfs. - Changed binary dump file permission from S_IRUSR to S_IRUGO. - Changed module name from CRASH_DRIVER_DUMP to CRASH_DEVICE_DUMP. rfc v2: - Collecting logs in 2nd kernel instead of during kernel panic. Suggested by Eric Biederman <ebiederm@xmission.com>. - Added new crashdd module that exports /proc/crashdd/ containing driver's registered hardware/firmware logs in patch 1. - Replaced the API to allow drivers to register their hardware/firmware log collect routine in crash recovery kernel in patch 1. - Updated patch 2 to use the new API in patch 1. ==================== Acked-by:
"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
-
Rahul Lakkireddy authored
Register callback to collect hardware/firmware dumps in second kernel before hardware/firmware is initialized. The dumps for each device will be available as elf notes in /proc/vmcore in second kernel. Signed-off-by:
Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by:
-
Rahul Lakkireddy authored
Update read and mmap logic to append device dumps as additional notes before the other elf notes. We add device dumps before other elf notes because the other elf notes may not fill the elf notes buffer completely and we will end up with zero-filled data between the elf notes and the device dumps. Tools will then try to decode this zero-filled data as valid notes and we don't want that. Hence, adding device dumps before the other elf notes ensure that zero-filled data can be avoided. This also ensures that the device dumps and the other elf notes can be properly mmaped at page aligned address. Incorporate device dump size into the total vmcore size. Also update offsets for other program headers after the device dumps are added. Suggested-by: Eric Biederman <ebiederm@xmission.com>. Signed-off-by:
-
Rahul Lakkireddy authored
The sequence of actions done by device drivers to append their device specific hardware/firmware logs to /proc/vmcore are as follows: 1. During probe (before hardware is initialized), device drivers register to the vmcore module (via vmcore_add_device_dump()), with callback function, along with buffer size and log name needed for firmware/hardware log collection. 2. vmcore module allocates the buffer with requested size. It adds an Elf note and invokes the device driver's registered callback function. 3. Device driver collects all hardware/firmware logs into the buffer and returns control back to vmcore module. Ensure that the device dump buffer size is always aligned to page size so that it can be mmaped. Also, rename alloc_elfnotes_buf() to vmcore_alloc_buf() to make it more generic and reserve NT_VMCOREDD note type to indicate vmcore device dump. Suggested-by: Eric Biederman <ebiederm@xmission.com>. Signed-off-by:
-
Paweł Jabłoński authored
This patch fixes a hardware reset support in VF driver. It is needed because when a hardware reset is detected adapter->state is in __I40EVF_RESETTING state before i40evf_reset_task is called. Without this patch unloading VF driver after a hardware reset ends with a system crash. Signed-off-by:
Paweł Jabłoński <pawel.jablonski@intel.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
