- 30 Mar, 2009 40 commits
-
-
Nicola Soranzo authored
Coding style fixes for recent changesets in em28xx. Signed-off-by:
Nicola Soranzo <nsoranzo@tiscali.it> Signed-off-by:
Douglas Schilling Landgraf <dougsland@redhat.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Hans Verkuil authored
Control arrays as are used with v4l2_ctrl_next must be sorted from low to high. Add a comment at the top of all such arrays to warn about this. Signed-off-by:
Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by:
-
Hans Verkuil authored
In order to convert the v4l1 zoran and vino i2c drivers to v4l2 these extra ops are required. Signed-off-by:
-
Hans Verkuil authored
The cx2341x_mpeg_ctrls array must be ordered by control ID. I know that this is bad design, but for now I will just fix this bug and revisit it when all drivers have moved to v4l2_device/v4l2_subdev, since that will allow me to do greatly improve control handling. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Tobias Lorenz authored
LED_REPORT and all flash REPORTs are on it's way. This code rearrangement cleans up the code for proper integration later on. Signed-off-by:
Tobias Lorenz <tobias.lorenz@gmx.net> Signed-off-by:
-
Tobias Lorenz authored
- "DealExtreme" sells the "PCear" radio and that comes from "Sanei Electric". - MPlayer is also usable as radio application. - Consistent usage of tabulators and blanks in the code. Signed-off-by:
-
Indika Katugampala authored
[dougsland@redhat.com: Fixed CodingStyle] Signed-off-by:
Indika Katugampala <indika_20012001@yahoo.co.jp> Signed-off-by:
-
Nicola Soranzo authored
Lots of coding style fixes and a typo correction for em28xx. [dougsland@redhat.com: fixed a reject due to a change on em28xx-audio.c] Signed-off-by:
-
Douglas Schilling Landgraf authored
Added DVC 101 model to Pinnacle Dazzle description Signed-off-by:
-
Douglas Schilling Landgraf authored
Added macros EM28XX_START_AUDIO and EM28XX_STOP_AUDIO for em28xx_cmd(). Signed-off-by:
-
Alexey Klimov authored
Patch removes printk and place em28xx_errdev macros to provide information about driver name to dmesg. Signed-off-by:
Alexey Klimov <klimov.linux@gmail.com> Signed-off-by:
-
Douglas Schilling Landgraf authored
Added lock for users count Signed-off-by:
-
Douglas Schilling Landgraf authored
Added spinlock for trigger session Signed-off-by:
-
Robert Krakora authored
Essentially if a snd_em28xx_capture_trigger() stop followed by a snd_em28xx_capture_trigger() start would not yield any data because there was some logic put in with an adev->shutdown variable which did not seem warranted in my humble opinion. It would cause snd_em28xx_capture_trigger start never to start up the audio stream until the device was closed and reopened again. Upon re-opening the device adev->shutdown is reset and audio data would again flow. Signed-off-by:
Robert Krakora <rob.krakora@messagenetsystems.com> Signed-off-by:
-
Robert Krakora authored
Fix for em28xx memory leak and function rename Signed-off-by:
-
Douglas Schilling Landgraf authored
Removed bad check. Thanks to Robert Krakora <rob.krakora@messagenetsystems.com> to report that. Signed-off-by:
-
Mauro Carvalho Chehab authored
Thanks to Peter Senna Tschudin <peter.senna@gmail.com> for borrow me one of those devices. Signed-off-by: -
Mauro Carvalho Chehab authored
Kaiomy entry. Thanks to Peter Senna Tschudin <peter.senna@gmail.com> for borrow me one of those devices. Signed-off-by: -
Mauro Carvalho Chehab authored
Thanks to Peter Senna Tschudin <peter.senna@gmail.com> for borrow me one of those devices. Signed-off-by: -
Mauro Carvalho Chehab authored
For i2c normal work, we need to slow down the bus speed. However, the slow down breaks the eeprom firmware load. So, use normal speed for eeprom booting and then restore the i2c speed after that. It should also be noticed that no other I2C transfer should be in course while booting from eeprom, otherwise, tda10046 goes into an instable state. So, proper locking are needed at the i2c bus master. Tested with saa7134 MSI TV @nyware A/D board, that comes with an eeprom with firmware version 29. Signed-off-by: -
Mauro Carvalho Chehab authored
KBL is not needed on saa7134, so, let's remove it. However, we should take some care to avoid opening the module while initializing it. This issue exists with newer udev's that opens a device as soon as the driver is registered. So, a proper lock is needed on open. Signed-off-by: -
Mauro Carvalho Chehab authored
Fix two broken controls where a step weren't specified. Without a step, userspace apps won't allow to adjust such controls. Signed-off-by: -
Mauro Carvalho Chehab authored
The waitqueue is never used. So, let's just remove it. Signed-off-by: -
Mauro Carvalho Chehab authored
Some saa7134 devices require to open an i2c gate before tuning. This patch fix the initialization for those devices. The nxt200x_gate_ctrl() logic were returned back to the old place, since we don't know how to close the gate. A future pacth could revert that change and provide the proper close gate control, to avoid keeping it open forever. Signed-off-by: -
Mauro Carvalho Chehab authored
On certain devices, before opening a tuner, we need to open the tuner gate via i2c. This patch just moves the tuner probing code to the same place where such i2c commands are handled, to make easier to fix this trouble on later patches. Signed-off-by: -
Mauro Carvalho Chehab authored
While here, be sure that gate will be kept disabled if an error occurs. Cc: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: -
Mauro Carvalho Chehab authored
The gate control logic is broken: several routines just keep it open; other rotines close it properly; there are even other routines that assumes that it is open without really checking or opening it. Instead of having to manually handle the gate control and having such troubles, let a sub-routine take care of the gate, opening it before i2c_transfer and closing it after that. This avoids leaving the gate into a random state. Cc: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: -
Hans Verkuil authored
Doing the v4l2_device registration in the saa7146 core will make it dependent on v4l2, even for DVB-only boards. This registration and unregistration belongs in saa7146_vv instead. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Modified mxb to load the i2c modules through v4l2_subdev. So no more probing. Modified tea6415c and tea6420 to use the standard routing ops to do the routing, rather than using private commands. Dropped the private commands from tda9840 (they were never used except during initialization of the module). Added saa7146 support for VIDIOC_DBG_G_CHIP_IDENT. Converted saa5246a and saa5249 to v4l2_subdev. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Prepare for converting to v4l2_subdev. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Drivers that implement this always have to set the ident and revision to V4L2_IDENT_NONE and 0. Do this in the v4l2 core so drivers don't have to do this. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
