- 11 Oct, 2019 27 commits
-
-
Eric Yang authored
[Why] The SMU message to enable this feature looks at argument. Previous code didn't send right argument. This change will allow the feature to be be enabled. [How] Fixed one issue where SMU message to enable the feature was sent without setting the parameter. Signed-off-by:
Eric Yang <Eric.Yang2@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com>
-
Eric Yang authored
[Why] If 48mhz refclk is turned off during PSR, we will have issue doing link training during detection. [How] Get out of PSR before detection Signed-off-by:
Tony Cheng <Tony.Cheng@amd.com> Acked-by:
Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by:
-
Julian Parkin authored
[Why] When diags adds a DWB via a stream update, we calculate MMHUBBUB paramaters, but dc->current_state has not yet been updated when the DWB programming happens. This leads to overflow on high bandwidth tests since the incorrect MMHUBBUB arbitration parameters are programmed. [How] Pass the updated context down to the (enable|update)_writeback functions so that they can use the correct watermarks when programming MMHUBBUB. Signed-off-by:
Julian Parkin <julian.parkin@amd.com> Reviewed-by:
Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Acked-by:
-
Aric Cyr authored
Signed-off-by:
Aric Cyr <aric.cyr@amd.com> Reviewed-by:
-
Wesley Chalmers authored
[WHY] dpp2_get_optimal_number_of_taps is incorrect, and dcn2 should be using dpp1_get_optimal_number_of_taps instead Signed-off-by:
Wesley Chalmers <Wesley.Chalmers@amd.com> Reviewed-by:
-
Sivapiriyan Kumarasamy authored
[Why] There is a bug when determining if link training should be retried when HPD is low in dp_verify_link_cap_with_retries. [How] Correctly, fail dp_verify_link_cap_with_retries without retry when HPD is low. Signed-off-by:
Sivapiriyan Kumarasamy <sivapiriyan.kumarasamy@amd.com> Reviewed-by:
Wenjing Liu <Wenjing.Liu@amd.com> Acked-by:
Abdoulaye Berthe <Abdoulaye.Berthe@amd.com> Acked-by:
-
Josip Pavic authored
[Why] When the driver sends a pipe set command to the DMCU FW, it does not wait for the command to complete. This can lead to unpredictable behavior if, for example, the driver were to request a pipe disable to the FW via MCP, then power down some hardware before the firmware has completed processing the command. [How] Wait for the DMCU FW to finish processing set pipe commands Signed-off-by:
Josip Pavic <Josip.Pavic@amd.com> Reviewed-by:
Anthony Koo <Anthony.Koo@amd.com> Acked-by:
-
Nikola Cornij authored
[why] Output bitrate was mistakenly left out, causing corruption on some DSC low resolution (such as 800x600) modes. Signed-off-by:
Nikola Cornij <nikola.cornij@amd.com> Reviewed-by:
-
Aric Cyr authored
[Why] Some displays rely on the SPD verticle frequency maximum value. Must round the calculated refresh rate to the nearest integer. [How] Round the nominal calculated refresh rate to the nearest whole integer. Signed-off-by:
-
Joshua Aberback authored
[Why] This function was mistakenly reverted as part of a legitimate revert. The old version that was reverted to has bad logic, and is causing situations where p-state change support is being toggled when it shouldn't be, resulting in hangs. Signed-off-by:
Joshua Aberback <joshua.aberback@amd.com> Reviewed-by:
Jun Lei <Jun.Lei@amd.com> Acked-by:
-
Lewis Huang authored
[Why] Type-c PHY config is not align with dpcd lane count. When those values didn't match, it cause driver do link training with 4 lane but phy only can output 2 lane. The link trainig always fail. [How] 1. Modify get_max_link_cap function. According DPALT_DP4 to update max lane count. 2. Add dp_mst_verify_link_cap to handle MST case because we didn't call dp_mst_verify_link_cap for MST case. Signed-off-by:
Lewis Huang <Lewis.Huang@amd.com> Reviewed-by:
-
Wayne Lin authored
[Why] Didn't send VSIF infopacket when it's 4k mode defined in HDMI 1.4b. For HDMI 1.4b, While displaying 4k modes, it should send VSP. [How] Call mod_build_hf_vsif_infopacket() function to build info frame and send it. Signed-off-by:
Wayne Lin <Wayne.Lin@amd.com> Reviewed-by:
Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Acked-by:
-
Anthony Koo authored
Signed-off-by:
-
Joshua Aberback authored
[Why] The register CM_TEST_DEBUG_DATA is used in dpp1_program_input_csc, which is called from dpp2_cnv_setup, but the shifts and masks for the fields of that register are not initialized for dcn2. This causes all reads of that register to return 0. Signed-off-by:
Jaehyun Chung <Jaehyun.Chung@amd.com> Acked-by:
-
Jun Lei authored
[why] memcmp is vulnerable to regression due to dc_clocks structures not being organized properly (not "current" clock related structures being at the beginning of the structure) and causes unnecessary setting of the optimize bit [how] add a dcn sepcific comparator, implement for dcn2 Signed-off-by:
-
Wayne Lin authored
[Why] The vendor specific infoframe is needed for HDMI while displaying specific modes. DC supports sending it, but we aren't currently building it [How] Add mod_build_hf_vsif_infopacket() to build the vendor specific info packet. Signed-off-by:
-
Joseph Gravenor authored
[why] HPD is not suppressed when we lower clocks on renoir. B/c of this we do link training when the 48mhz refclk is off, which will cause ASIC hang. [how] Exit optimized power state for detection purpose. Signed-off-by:
Joseph Gravenor <joseph.gravenor@amd.com> Reviewed-by:
-
Dmytro Laktyushkin authored
Currently pipe split may steal an existing ODM pipe depending on stream sequence. This change prevents that from happening as easily. Signed-off-by:
Gary Kattan <Gary.Kattan@amd.com> Acked-by:
-
Julian Parkin authored
[Why] When planes are added or removed from a stream, the change in pipe usage from dynamic MPC combine can cause a second stream using ODM combine to pick a different pipe to combine with. In this scenario, a different OPP is connected to the ODM without programming its FMT. [How] Reprogram the FMT in dcn20_program_pipe whenever a pipe is newly enabled, or when its opp changes. Signed-off-by:
-
Aric Cyr authored
[Why] If VSTARTUP changes due to bandwidth requirements, we must recalculate and update VLINE2 as well for proper flip reporting. [How] After all calls to program_global_sync which reconfigures VSTARTUP, also make sure to update V_UPDATE (i.e. VLINE2 on DCNx). Signed-off-by:
-
Wyatt Wood authored
[Why] A recent bug showed that logging would be useful in debugging various gamma issues. [How] Fix formatting for easier graphing. Prevent performance hit when doing diag. Signed-off-by:
Wyatt Wood <wyatt.wood@amd.com> Reviewed-by:
-
Wenjing Liu authored
[why] Virtual signal means there is no display attached. In this case we will assign a virtual signal type to the stream. We should only enable the front end of the stream but not the back end. [how] When stream is enabling with virtual signal type, skip backend programming. Signed-off-by:
-
Wayne Lin authored
[Why] While displaying 4k modes defined in HDMI1.4b, should set VIC to 0 and use VSP HDMI_VIC to indicate the mode. [How] Use functions defined in drm to set up the VIC correspondingly. Signed-off-by:
-
Robin Singh authored
[Why] To compare the crc of the framebuffer data at input of display pipeline with the crc of the otg, we need to disable pixel formatter's dynamic expansion feature during crc capture and keep it enable in the normal operation. [HOW] Expose a new interface in DM and dc for pixel formatter (fmt dynamic bitdepth expansion control). Interface control the FMT_DYNAMIC_EXP_EN bit, during crc capture keep it disabled. Signed-off-by:
Robin Singh <robin.singh@amd.com> Reviewed-by:
Harry Wentland <Harry.Wentland@amd.com> Acked-by:
-
Oak Zeng authored
This allows gfx cache to be probed and invalidated (for none-dirty cache lines) on a HDP write (from either another GPU or CPU). This should work only for the memory mapped as RW memory type newly added for arcturus, to achieve some cache coherence b/t multiple memory clients. Signed-off-by:
Oak Zeng <Oak.Zeng@amd.com> Acked-by:
Christian Konig <christian.koenig@amd.com> Signed-off-by:
-
Oak Zeng authored
Many logic in this function are HDP set up, not gart set up. Moved those logic to gmc_v9_0_hw_init. No functional change. Signed-off-by:
-
Marek Olšák authored
Use asic constants. Signed-off-by:
Marek Olšák <marek.olsak@amd.com> Reviewed-by:
-
- 09 Oct, 2019 1 commit
-
-
Stephen Rothwell authored
Signed-off-by:
Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by:
-
- 07 Oct, 2019 12 commits
-
-
Harish Kasiviswanathan authored
Participate in device cgroup. All kfd devices are exposed via /dev/kfd. So use /dev/dri/renderN node. Before exposing the device to a task check if it has permission to access it. If the task (based on its cgroup) can access /dev/dri/renderN then expose the device via kfd node. If the task cannot access /dev/dri/renderN then process device data (pdd) is not created. This will ensure that task cannot use the device. In sysfs topology, all device nodes are visible irrespective of the task cgroup. The sysfs node directories are created at driver load time and cannot be changed dynamically. However, access to information inside nodes is controlled based on the task's cgroup permissions. Signed-off-by:
Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com> Reviewed-by:
Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by:
-
Harish Kasiviswanathan authored
For AMD compute (amdkfd) driver. All AMD compute devices are exported via single device node /dev/kfd. As a result devices cannot be controlled individually using device cgroup. AMD compute devices will rely on its graphics counterpart that exposes /dev/dri/renderN node for each device. For each task (based on its cgroup), KFD driver will check if /dev/dri/renderN node is accessible before exposing it. Signed-off-by:
Tejun Heo <tj@kernel.org> Acked-by:
Roman Gushchin <guro@fb.com> Signed-off-by:
-
Alex Deucher authored
Add proper ifdefs around CIK code in kfd setup. Reviewed-by:
-
Krzysztof Kozlowski authored
Adjust indentation from spaces to tab (+optional two spaces) as in coding style with command like: $ sed -e 's/^ /\t/' -i */Kconfig Signed-off-by:Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by:
-
Ori Messinger authored
The vram vendor can be found as a separate sysfs file at: /sys/class/drm/card[X]/device/mem_info_vram_vendor The vram vendor is displayed as a string value. v2: Use correct bit masking, and cache vram_vendor in gmc v3: Drop unused functions for vram width, type, and vendor Signed-off-by:
Ori Messinger <ori.messinger@amd.com> Reviewed-by:
-
Dan Carpenter authored
In the current code if "device_info" is ever NULL then the kernel will Oops so probably || was intended instead of &&. Fixes: e392c887 ("drm/amdkfd: Use array to probe kfd2kgd_calls") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Dan Carpenter authored
The error handling is off by one. We should not free the first "tables[i].bo" without decrementing "i" because that might result in a double free. The second problem is that when an error occurs, then the zeroth element "tables[0].bo" isn't freed. I had make "i" signed int for the error handling to work, so I just updated "ret" as well as a clean up. Fixes: f96357a9 ("drm/amd/powerplay: implement smu_init(fini)_fb_allocations function") Reviewed-by:
Kevin Wang <kevin1.wang@amd.com> Signed-off-by:
-
Dan Carpenter authored
This function needs to drop the mutex before returning. Fixes: f7e3a577 ("drm/amd/powerplay: check SMU engine readiness before proceeding on S3 resume") Reviewed-by:
-
zhengbin authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c: In function dce110_enable_audio_stream: drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c:949:23: warning: variable pp_smu set but not used [-Wunused-but-set-variable] drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c: In function dce110_disable_audio_stream: drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c:983:23: warning: variable pp_smu set but not used [-Wunused-but-set-variable] drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c: In function dce110_program_front_end_for_pipe: drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c:2429:19: warning: variable old_pipe set but not used [-Wunused-but-set-variable] 'pp_smu' is not used since commit 170a2398 ("drm/amd/display: make clk_mgr call enable_pme_wa") 'old_pipe' is not used since commit 65d38262 ("drm/amd/display: fbc state could not reach while enable fbc") Reviewed-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
zhengbin <zhengbin13@huawei.com> Signed-off-by:
-
zhengbin authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/gpu/drm/amd/display/dc/dcn20/dcn20_dpp.c: In function dpp2_get_optimal_number_of_taps: drivers/gpu/drm/amd/display/dc/dcn20/dcn20_dpp.c:359:11: warning: variable pixel_width set but not used [-Wunused-but-set-variable] It is not used since commit f7de96ee ("drm/amd/display: Add DCN2 DPP") Reviewed-by:
-
zhengbin authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/gpu/drm/amd/display/dc/dcn20/dcn20_dwb_scl.c: In function dwb_program_horz_scalar: drivers/gpu/drm/amd/display/dc/dcn20/dcn20_dwb_scl.c:725:11: warning: variable h_ratio_chroma set but not used [-Wunused-but-set-variable] drivers/gpu/drm/amd/display/dc/dcn20/dcn20_dwb_scl.c: In function dwb_program_vert_scalar: drivers/gpu/drm/amd/display/dc/dcn20/dcn20_dwb_scl.c:806:11: warning: variable v_ratio_chroma set but not used [-Wunused-but-set-variable] They are not used since commit 345429a6 ("drm/amd/display: Add DCN2 DWB") Reviewed-by:
-
zhengbin authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/gpu/drm/amd/display/dc/dsc/rc_calc.c: In function calc_rc_params: drivers/gpu/drm/amd/display/dc/dsc/rc_calc.c:180:6: warning: variable source_bpp set but not used [-Wunused-but-set-variable] It is not used since commit 97bda032 ("drm/amd/display: Add DSC support for Navi (v2)") Reviewed-by:
-
