- 27 Apr, 2007 40 commits
-
-
Mauro Carvalho Chehab authored
there were several "magic" for loops, addressing gpiomux array size (4). Adrian Bunk showed that one of the loops were wrong, going from 0 to 4. This patch provides the right fix for this trouble, by using ARRAY_SIZE on all places where we have a for loop using gpiomux. Thanks to: Adrian Bunk <bunk@stusta.de> for pointing me about this trouble. Signed-off-by:Mauro Carvalho Chehab <mchehab@infradead.org>
-
Luca Risolia authored
@ Don't assume that SOF headers can't cross packets boundaries @ Fix compression quality selection + Add support for MI-0360 image sensor * Documentation updates @ Fix sysfs @ MI0343 rewritten * HV7131R color fixes and add new ABLC control * Rename the archive from "sn9c102" to "sn9c1xx" * fix typos * better support for TAS5110D @ fix OV7630 wrong colors @ Don't return an error if no input buffers are enqueued yet on VIDIOC_STREAMON * Add informations about colorspaces * More appropriate error codes in case of failure of some system calls * More precise hardware detection * Add more informations about supported hardware in the documentation + More supported devices + Add support for HV7131R image sensor Signed-off-by:
Luca Risolia <luca.risolia@studio.unibo.it> Signed-off-by:
-
Adrian Bunk authored
After looking at a section bug (in the non-modular case, clearly non-init code referenced the __initdata parport_nr[]), I thought it was time to convert this driver to module_{init,exit}. Signed-off-by:Adrian Bunk <bunk@stusta.de> Signed-off-by:
-
Jonathan Corbet authored
Add raw bayer support to the ov7670 driver Signed-off-by:
Jonathan Corbet <corbet@lwn.net> Signed-off-by:
-
Jonathan Corbet authored
Fix up Cafe/ov7670 copyrights and maintainer entries Signed-off-by:
-
Jonathan Corbet authored
Don't mirror ov7670 images by default. The ov7670 sensor driver sets the mirror bit by default, which is not the desired mode. OLPC has been running with this patch for a while. Signed-off-by:
-
Jonathan Corbet authored
Add suspend/resume support to the Cafe CCIC driver. Signed-off-by:
-
Jonathan Corbet authored
Fix up unsociable Cafe CCIC delays. The Cafe CCIC driver contains some lengthy delays, some of which are unnecessary and some of which are done under lock. Some were marked with comments, but the comments somehow failed to make the issue go away. So fix it for real. Signed-off-by:
-
Jonathan Corbet authored
Remove an obsolete PCI ID. The CAFE driver includes three PCI IDs, one of which corresponds to a development board which is no longer in use. Signed-off-by:
-
Jonathan Corbet authored
Set the PCI dev in the V4L2 dev so that the proper sysfs link gets made Signed-off-by:
Dan Williams <dcbw@redhat.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
Logitech ViewPort AV 100 has the same internals as Cisco VT Camera. Fixing Pwc driver to handle it properly. Also, fixed the comments for both cameras. Thanks to Martin Rubli for pointing me this. Signed-off-by: -
Jean Tourrilhes authored
I have a Cisco VT Camera, and it was just collecting dust. I decided to try connecting it to my Linux box at home. Just a disgression about the product. The Cisco VT Camera is a webcam Cisco sold to work with their IP phone hardware and software. It's mostly useless on Windows, as it interfaces only to Cisco software. You can find some for cheap on eBay... Physically, it's just a Logitech Pro 4000. The only difference with the Pro 4000 is the Cisco logo and that it's grey like the Pro 3000. I believe Cisco is now selling the Cisco VT Camera II, which look to be something else... So, assuming that it was a Pro 4000 inside, I created the little patch attached. I'm new to webcam under Linux, but I managed to get an image from it using xawtv, and the image looked all right, so I consider that a success. The imaged seemed a bit small and I could not get the microphone driver loaded, but I assume it's my lack of experience. Note that I did not try any other type_id, but this one works great. Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Pierre Willenbrock authored
Add support for Anubis Electronics "Lifeview" (USB-ID: 0x10fd:0x1513) Signed-off-by:
Pierre Willenbrock <pierre@pirsoft.de> Signed-off-by:
Michael Krufky <mkrufky@linuxtv.org> Signed-off-by:
-
Hartmut Hackmann authored
The struct tda1004x_config has a new entry: .ts_mode Possible values are TDA10046_TS_PARALLEL or TDA10046_TS_SERIAL There always is only one interface active, default is parallel. Signed-off-by:
Hartmut Hackmann <hartmut.hackmann@t-online.de> Signed-off-by:
-
Trent Piepho authored
The dvb-pll sleep function could only send a 2-byte sequence to the PLL. This isn't enough in some cases, for example fmd1216me will need to send a 4-byte command to set both BB and AB to the correct values. Instead of using a fake band with a frequency of 0 to store the sleep data (which has room for only two bytes), the new sleep function works like the init function. A new pointer is added to the pll description, and when non-NULL points to a buffer with the length and data to send. Signed-off-by:
Trent Piepho <xyzzy@speakeasy.org> Signed-off-by:
-
Trent Piepho authored
The IF frequency was specified for each band, but it's not something that changes from band to band. None of the tuner definitions had a different IF frequency (called offset) from one band to another. Acked-by:
-
Trent Piepho authored
Some PLLs had one half the step size added to the offset, so that the divisor would be rounded to the nearest integer. Some didn't and so would always be rounded down. This makes dvb-pll round to the nearest when calculating the divisor, without the offset needing to be fudged. PLLs that had a fudged offset have the offset changed to be just the IF frequency. The satellite PLL dvb_pll_philips_sd1878_tda8261 was rounding up for some reason, and I've kept it that way. In addition, frequencies that were rounded to the nearest kHz are extended to full Hz resolution. One sixth MHz step sizes that were listed as 166,666 Hz are changed to 166,667 Hz, which is slightly closer. PLLs that were already rounding: dvb_pll_tda665x, offset was 36 1/6 (to nearest kHz) + step/2 dvb_pll_fmd1216me, offset was 36 1/8 (to two digits) + step/2 dvb_pll_thomson_fe6600, offset was 36 1/8 (to two digits) + step/2 dvb_pll_env57h1xd5, offset was 36 1/8 + step Note that the last PLL, dvb_pll_env57h1xd5, appears to have had a bug in the offset. Rather than adding stepsize/2, it was adding a full stepsize. The PLL definition originally came from the dibusb driver, which used 36 1/8 + step/2. The change to 36 1/8 + step was probably a mistake added when the tuner was converted to dvb-pll. Signed-off-by:
-
Trent Piepho authored
The attach code for HAUPPAUGE_HVR3000 and HAUPPAUGE_HVR1300 is exactly the same as the code used by HAUPPAUGE_HVR1100, HAUPPAUGE_HVR1100LP, and WINFAST_DTV2000H. So, those first two cards are added to the case block used by the last three. Signed-off-by:
-
Pierre Willenbrock authored
Signed-off-by:
Pierre Willenbrock <pierre@pirsoft.dnsalias.org> Signed-off-by:
Aapo Tahkola <aet@rasterburn.org> Signed-off-by:
-
Aapo Tahkola authored
This function should work for all m920x-based devices. Signed-off-by:
-
Hartmut Hackmann authored
The new name fits to what it is and what is on the box. Signed-off-by:
-
Hartmut Hackmann authored
There are 2 new entries for p7131 boards and one correction for a board with LNA. Signed-off-by:
-
Hartmut Hackmann authored
Static locals should not be changed - the original contents gets lost. Thanks to Trent Piepho for pointing me to this. Signed-off-by:
-
Hartmut Hackmann authored
Besides power saving, this puts the AGC output of the tda8290 to tristate. This is necessary for some hybrid boards which don't use a multiplexer for the AGC Signed-off-by:
-
Oliver Endriss authored
Fix bug introduced during infrared refactoring. Thanks to Johann Friedrichs for spotting this. Thanks-to: Johann Friedrichs <johann.friedrichs@web.de> Signed-off-by:
Oliver Endriss <o.endriss@gmx.de> Signed-off-by:
-
Ian Armstrong authored
Modifies automatic mode selection for yuv playback. Behaviour is now that source video with a vertical resolution below that of the currently set broadcast mode will be treated as progressive. Video with a vertical resolution greater or equal to the current broadcast mode (up to 576 lines) will be treated as interlaced. Signed-off-by:
Ian Armstrong <ian@iarmst.demon.co.uk> Signed-off-by:
Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by:
-
Ian Armstrong authored
Adds more osd mode switching information. Corrects some information regarding mode selection & local alpha operation for 16 bit modes. Signed-off-by:
-
Hans Verkuil authored
The TV standard should be set AFTER the TV output is fully initialized. Signed-off-by:
-
Steven Toth authored
Some of the new tuner entries may need to be mapped to compatible tuners already defined. I don't know for certain which tuners are compatible between manufacturers. Signed-off-by:
Steven Toth <stoth@hauppauge.com> Signed-off-by:
-
Michael Krufky authored
replace leading spaces with tabs Signed-off-by:
-
Michael Krufky authored
The ADS Tech InstantTV DVB-S is a clone of the KWorld DVB-S 100. This patch adds autodetection support for this card based on pci subsystem id. Signed-off-by:
-
Trent Piepho authored
Change a 00 to just 0 Detect zero-length I2C messages and return not supported. I think I know how to send one, but the problem is getting the slave's ack. The only point of a zero-length message is for probing; too see if the slave will ack its address. Since we don't know how to get the ack, we can't support zero-length messages in a useful way, so it's probably best to just return not supported for them. Signed-off-by:
-
Trent Piepho authored
Write some better documentation about what might be known about how the m920x I2C works, since a datasheet is lacking. The I2C xfer function should now handle more types of I2C transactions than it could before. Those it can't, will return error codes instead of being executed incorrectly. Multi-byte reads were not being done correctly, which should be fixed. Signed-off-by:
-
Aapo Tahkola authored
Signed-off-by:
-
Aapo Tahkola authored
Signed-off-by:
-
Aapo Tahkola authored
- r/w bit is not part of the i2c address Signed-off-by:
-
Aapo Tahkola authored
- Implement m920x i2c as suggested by Pierre Willenbrock - remove "magic" hack - r/w bit is not part of the i2c address - move hardware remarks to header file Signed-off-by:
-
Hans Verkuil authored
Once the devices have been registered anyone can start changing the inputs or TV standard before they have been initialized by the driver. This leads to cases were the input is changed in an udev rule, but after that rule is triggered the tail-end of the ivtv driver initialization can override that by selecting the tuner input. The correct sequence is to first setup the input, initial frequency and TV standard before finally registering the video devices. This prevents any udev rules from being triggered prematurely. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Negative speed values have to be allowed for reverse playback. Signed-off-by:
-
