- 02 Oct, 2020 3 commits
-
-
Heikki Krogerus authored
It's not an error if the mode can't be entered because another mode is already active, so no longer printing an error message if that happens. Signed-off-by:
Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20200928133324.48841-1-heikki.krogerus@linux.intel.comSigned-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alan Stern authored
Description based on one by Yasushi Asano: According to 6.7.22 A-UUT “Device No Response” for connection timeout of USB OTG and EH automated compliance plan v1.2, enumeration failure has to be detected within 30 seconds. However, the old and new enumeration schemes each make a total of 12 attempts, and each attempt can take 5 seconds to time out, so the PET test fails. This patch adds a new Kconfig option (CONFIG_USB_FEW_INIT_RETRIES); when the option is set all the initialization retry loops except the outermost are reduced to a single iteration. This reduces the total number of attempts to four, allowing Linux hosts to pass the PET test. The new option is disabled by default to preserve the existing behavior. The reduced number of retries may fail to initialize a few devices that currently do work, but for the most part there should be no change. And in cases where the initialization does fail, it will fail much more quickly. Reported-and-tested-by:
yasushi asano <yazzep@gmail.com> Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20200928152217.GB134701@rowland.harvard.eduSigned-off-by:
-
Alan Stern authored
The SET_CONFIG_TRIES macro in hub.c is badly named; it controls the number of port-initialization retry attempts rather than the number of Set-Configuration attempts. Furthermore, the USE_NEW_SCHEME macro and use_new_scheme() function are written in a very confusing manner, making it almost impossible to figure out exactly what they do or check that they are correct. This patch renames SET_CONFIG_TRIES to PORT_INIT_TRIES, removes USE_NEW_SCHEME entirely, and rewrites use_new_scheme() to be much more transparent, with added comments explaining how it works. The patch also pulls the single call site of use_new_scheme() out from the Get-Descriptor retry loop (where it returns the same value each time) and renames the local variable used to store the result. The overall effect is a minor cleanup. However, there is one functional change: If the "use_both_schemes" module parameter isn't set (by default it is set), the existing code does only two retry iterations. After this patch it will always perform four, regardless of the parameter's value. Signed-off-by:
-
- 30 Sep, 2020 1 commit
-
-
Greg Kroah-Hartman authored
Merge tag 'thunderbolt-for-v5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next Mika writes: thunderbolt: Changes for v5.10 merge window This includes following Thunderbolt/USB4 changes for v5.10 merge window: * A couple of optimizations around Tiger Lake force power logic and NHI (Native Host Interface) LC (Link Controller) mailbox command processing * Power management improvements for Software Connection Manager * Debugfs support * Allow KUnit tests to be enabled also when Thunderbolt driver is configured as module. * Few minor cleanups and fixes All these have been in linux-next with no reported issues. * tag 'thunderbolt-for-v5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt: (37 commits) thunderbolt: Capitalize comment on top of QUIRK_FORCE_POWER_LINK_CONTROLLER thunderbolt: Correct tb_check_quirks() kernel-doc thunderbolt: Log correct zeroX entries in decode_error() thunderbolt: Handle ERR_LOCK notification thunderbolt: Use "if USB4" instead of "depends on" in Kconfig thunderbolt: Allow KUnit tests to be built also when CONFIG_USB4=m thunderbolt: Only stop control channel when entering freeze thunderbolt: debugfs: Fix uninitialized return in counters_write() thunderbolt: Add debugfs interface thunderbolt: No need to warn in TB_CFG_ERROR_INVALID_CONFIG_SPACE thunderbolt: Introduce tb_switch_is_tiger_lake() thunderbolt: Introduce tb_switch_is_ice_lake() thunderbolt: Check for Intel vendor ID when identifying controller thunderbolt: Introduce tb_port_is_nhi() thunderbolt: Introduce tb_switch_next_cap() thunderbolt: Introduce tb_port_next_cap() thunderbolt: Move struct tb_cap_any to tb_regs.h thunderbolt: Add runtime PM for Software CM thunderbolt: Create device links from ACPI description ACPI: Export acpi_get_first_physical_node() to modules ...
-
- 25 Sep, 2020 29 commits
-
-
Johan Hovold authored
For interfaces that lack a union descriptor, probe for a "combined-interface" before falling back to the call-management descriptor instead of the other way round. This allows for the removal of the NO_DATA_INTERFACE quirk and makes the probe algorithm somewhat easier to follow. Acked-by:
Oliver Neukum <oneukum@suse.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20200921135951.24045-5-johan@kernel.orgSigned-off-by:
-
Johan Hovold authored
Use the data-class define provided by USB core and drop the driver-specific one. Acked-by:
-
Johan Hovold authored
Handle broken union functional descriptors where the master-interface doesn't exist or where its class is of neither Communication or Data type (as required by the specification) by falling back to "combined-interface" probing. Note that this still allows for handling union descriptors with switched interfaces. This specifically makes the Whistler radio scanners TRX series devices work with the driver without adding further quirks to the device-id table. Reported-by:
Daniel Caujolle-Bert <f1rmb.daniel@gmail.com> Tested-by:
-
Johan Hovold authored
This reverts commit 2ad9d544. Drop bogus sanity check; an interface in the active configuration will always have a current altsetting assigned by USB core. Acked-by:
-
Greg Kroah-Hartman authored
The usb_control_msg_send() and usb_control_msg_recv() calls can return an error if a "short" write/read happens, and they can handle data off of the stack, so move the driver over to using those calls instead, saving some logic when dynamically allocating memory. v2: changed API of use usb_control_msg_send() and usb_control_msg_recv() Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Link: https://lore.kernel.org/r/20200914153756.3412156-11-gregkh@linuxfoundation.orgSigned-off-by:
-
Greg Kroah-Hartman authored
The usb_control_msg_send() call can return an error if a "short" write happens, so move the driver over to using that call instead. v2: API change of use usb_control_msg_send() Cc: Jaroslav Kysela <perex@perex.cz> Reviewed-by:
Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/20200914153756.3412156-10-gregkh@linuxfoundation.orgSigned-off-by:
-
Greg Kroah-Hartman authored
The usb_control_msg_send() and usb_control_msg_recv() calls can return an error if a "short" write/read happens, and they can handle data off of the stack, so move the driver over to using those calls instead, saving some logic when dynamically allocating memory. v2: API change of use usb_control_msg_send() and usb_control_msg_recv() Cc: Jaroslav Kysela <perex@perex.cz> Cc: Vasily Khoruzhick <anarsoul@gmail.com> Reviewed-by:
-
Greg Kroah-Hartman authored
The usb_control_msg_recv() function can handle data on the stack, as well as properly detecting short reads, so move to use that function instead of the older usb_control_msg() call. This ends up removing a lot of extra lines in the driver. v2: change API of usb_control_msg_send() Cc: Juergen Stuber <starblue@users.sourceforge.net> Link: https://lore.kernel.org/r/20200914153756.3412156-6-gregkh@linuxfoundation.orgSigned-off-by:
-
Greg Kroah-Hartman authored
The usb_control_msg_send() and usb_control_msg_recv() calls can return an error if a "short" write/read happens, so move the driver over to using those calls instead, saving some logic in the wrapper functions that were being used in this driver. This also resolves a long-staging bug where data on the stack was being sent in a USB control message, which was not allowed. v2: API change of usb_control_msg_send() Cc: Jaroslav Kysela <perex@perex.cz> Reviewed-by:
-
Greg Kroah-Hartman authored
The usb_control_msg_send() call can handle data on the stack, as well as returning an error if a "short" write happens, so move the driver over to using that call instead. This ends up removing a helper function that is no longer needed. v2: API change in usb_control_msg_send() Cc: Jaroslav Kysela <perex@perex.cz> Reviewed-by:
-
Oliver Neukum authored
They need to specify how memory is to be allocated, as control messages need to work in contexts that require GFP_NOIO. Signed-off-by:
-
Oliver Neukum authored
This reverts commit be40c366. The API has to be changed. Signed-off-by:
-
Oliver Neukum authored
This reverts commit ec8eeceb. The API has to be changed. Signed-off-by:
-
Oliver Neukum authored
This reverts commit aea67cc1. The API has to be changed. Signed-off-by:
-
Oliver Neukum authored
This reverts commit f7ef7614. The API has to be changed. Signed-off-by:
-
Oliver Neukum authored
This reverts commit 119ae38a. The API has to be changed. Signed-off-by:
-
Oliver Neukum authored
This reverts commit e9b20f0f. The API has to be changed Signed-off-by:
-
Oliver Neukum authored
This reverts commit d6a49924. Control messages are needed in contexts when memory allocations are restricted, such as handling device resets and runtime PM. For this reason the control message API internally uses GFP_NOIO. This is a band aid introduced because when we recognized the issue, the call chains were highly convoluted. Continuing this trend is not a good idea. So I am shooting the whole kennel here. Signed-off-by:
-
Chunfeng Yun authored
Arguments description of read_poll_timeout_atomic() is out of date, update it. Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Chunfeng Yun <chunfeng.yun@mediatek.com> Link: https://lore.kernel.org/r/1600668815-12135-11-git-send-email-chunfeng.yun@mediatek.comSigned-off-by:
-
Chunfeng Yun authored
Use readl_poll_timeout_atomic() to simplify code Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Felipe Balbi <balbi@kernel.org> Acked-by:
-
Chunfeng Yun authored
Use readl_poll_timeout_atomic() to simplify code Signed-off-by:
-
Chunfeng Yun authored
Use readl_poll_timeout_atomic() to simplify code Signed-off-by:
-
Chunfeng Yun authored
Use readl_poll_timeout_atomic() to simplify code Signed-off-by:
-
Chunfeng Yun authored
Use readl_poll_timeout_atomic() to simplify code Signed-off-by:
-
Chunfeng Yun authored
Use readl_poll_timeout_atomic() to simplify code Signed-off-by:
-
Chunfeng Yun authored
Use readl_poll_timeout_atomic() to simplify code Cc: Mathias Nyman <mathias.nyman@linux.intel.com> Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by:
-
Chunfeng Yun authored
Use readl_poll_timeout_atomic() to simplify code Cc: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Chunfeng Yun authored
Use readl_poll_timeout_atomic() to simplify code Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Petr Mladek <pmladek@suse.com> Signed-off-by:
-
Chunfeng Yun authored
Use readl_poll_timeout_atomic() to simplify code Cc: Lu Baolu <baolu.lu@linux.intel.com> Cc: Mathias Nyman <mathias.nyman@linux.intel.com> Reviewed-by:
Jann Horn <jannh@google.com> Signed-off-by:
-
- 22 Sep, 2020 5 commits
-
-
Lad Prabhakar authored
Document RZ/G2H (R8A774E1) SoC bindings. Reviewed-by:
Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com> Reviewed-by:
Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by:
Rob Herring <robh@kernel.org> Signed-off-by:
Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Link: https://lore.kernel.org/r/1594919915-5225-12-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.comSigned-off-by:
-
Lad Prabhakar authored
Document RZ/G2H (R8A774E1) SoC bindings. Reviewed-by:
-
Liu Shixin authored
module_usb_driver() makes the code simpler by eliminating boilerplate code. Signed-off-by:
Liu Shixin <liushixin2@huawei.com> Link: https://lore.kernel.org/r/20200918031012.3980558-1-liushixin2@huawei.comSigned-off-by:
-
Liu Shixin authored
module_bcma_driver() makes the code simpler by eliminating boilerplate code. Signed-off-by:
-
Greg Kroah-Hartman authored
Merge tag 'usb-ci-v5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next Peter writes: Two changes for chipidea imx driver: - Add picophy parameter tuning interface - Restore pinctrl for system suspend/resume * tag 'usb-ci-v5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb: usb: chipidea: ci_hdrc_imx: restore pinctrl usb: chipidea: imx: add two samsung picophy parameters tuning implementation doc: dt-binding: ci-hdrc-usb2: add property for samsung picophy
-
- 21 Sep, 2020 2 commits
-
-
Greg Kroah-Hartman authored
Merge a3112838 ("Merge tag 'libnvdimm-fixes-5.9-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm") into usb-next We need the dax build fix in here as well, so that the build does not break. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimmLinus Torvalds authored
Pull libnvdimm fix from Dan Williams: "Fix compilation for the new dax_supported() exported helper" * tag 'libnvdimm-fixes-5.9-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: dax: Fix compilation for CONFIG_DAX && !CONFIG_FS_DAX
-
