1. 12 Nov, 2014 12 commits
  2. 10 Nov, 2014 18 commits
  3. 04 Nov, 2014 2 commits
    • Tony Lindgren's avatar
      ARM: dts: Fix missing GPMC NAND device width for omap3 boards · 24f284af
      Tony Lindgren authored
      Looks like we have some GPMC NAND timings missing device
      width. This fixes "gpmc_cs_program_settings: invalid width 0!"
      errors during boot.
      Signed-off-by: default avatarTony Lindgren <tony@atomide.com>
      24f284af
    • Tony Lindgren's avatar
      ARM: dts: Use better omap GPMC timings for LAN9220 · 13aec8e4
      Tony Lindgren authored
      With the GPMC warnings now enabled, I noticed the LAN9220 timings
      can overflow the GPMC registers with 200MHz L3 speed. Earlier we
      were just skipping the bad timings and would continue with the
      bootloader timings. Now we no longer allow to continue with bad
      timings as we have the timings in the .dts files.
      
      We could start using the GPMC clock divider, but let's instead
      use the u-boot timings that are known to be working and a bit
      faster. These are basically the u-boot NET_GPMC_CONFIG[1-6]
      defines deciphered. Except that we don't set gpmc,burst-length
      as that's only partially configured and does not seem to work
      if fully enabled.
      
      [tony@atomide.com: updated to remove gpmc,burst-length]
      Signed-off-by: default avatarTony Lindgren <tony@atomide.com>
      13aec8e4
  4. 30 Oct, 2014 4 commits
    • Tony Lindgren's avatar
      ARM: dts: Add GPMC timings for omap zoom serial port · b5399ea8
      Tony Lindgren authored
      The four port serial port on the zoom debug board uses a TL16CP754C
      with a single interrupt and GPMC chip select. The serial ports each
      use a 8 bytes for IO registers, and are 256 bytes apart on the GPMC
      line.
      
      Let's add timings for all four ports so we can remove the GPMC
      workarounds for using bootloader timings.
      
      Not caused by this patch, but looks like u-boot only properly
      initializes the fifo on the first serial port. Currently the other
      ports produce garbage at least with my version of u-boot. I suspect
      that TL16CP754C needs non-standard initialization added to 8250
      driver to properly fix this issue.
      
      Cc: Roger Quadros <rogerq@ti.com>
      Signed-off-by: default avatarTony Lindgren <tony@atomide.com>
      b5399ea8
    • Tony Lindgren's avatar
      ARM: dts: Add smc91x GPMC configuration for 2430sdp · 1bb37404
      Tony Lindgren authored
      Let's use the bootloader values except for the partially configured
      wait-pin that does not seem to work.
      
      Cc: Roger Quadros <rogerq@ti.com>
      Signed-off-by: default avatarTony Lindgren <tony@atomide.com>
      1bb37404
    • Tony Lindgren's avatar
      ARM: dts: Fix wrong GPMC size mappings for omaps · e2c5eb78
      Tony Lindgren authored
      The GPMC binding is obviously very confusing as the values
      are all over the place. People seem to confuse the GPMC partition
      size for the chip select, and the device IO size within the GPMC
      partition easily.
      
      The ranges entry contains the GPMC partition size. And the
      reg entry contains the size of the IO registers of the
      device connected to the GPMC.
      
      Let's fix the issue according to the following table:
      
      Device          GPMC partition size     Device IO size
      connected       in the ranges entry     in the reg entry
      
      NAND            0x01000000 (16MB)       4
      16550           0x01000000 (16MB)       8
      smc91x          0x01000000 (16MB)       0xf
      smc911x         0x01000000 (16MB)       0xff
      OneNAND         0x01000000 (16MB)       0x20000 (128KB)
      16MB NOR        0x01000000 (16MB)       0x01000000 (16MB)
      32MB NOR        0x02000000 (32MB)       0x02000000 (32MB)
      64MB NOR        0x04000000 (64MB)       0x04000000 (64MB)
      128MB NOR       0x08000000 (128MB)      0x08000000 (128MB)
      256MB NOR       0x10000000 (256MB)      0x10000000 (256MB)
      
      Let's also add comments to the fixed entries while at it.
      Acked-by: default avatarRoger Quadros <rogerq@ti.com>
      Signed-off-by: default avatarTony Lindgren <tony@atomide.com>
      e2c5eb78
    • Tony Lindgren's avatar
      ARM: dts: Fix bootloader version dependencies by muxing n900 smc91x pins · 9a894953
      Tony Lindgren authored
      Apparently some versions of nolo don't mux the all the necessary GPMC
      pins for the smc91x probe to work properly. Let's fix this issue
      by adding mux support for GPMC to the kernel.
      
      Note that GPMC clk needs input enabled for OnenNAND to work.
      
      Cc: Kevin Hilman <khilman@kernel.org>
      Cc: Roger Quadros <rogerq@ti.com>
      Signed-off-by: default avatarTony Lindgren <tony@atomide.com>
      9a894953
  5. 26 Oct, 2014 4 commits
    • Linus Torvalds's avatar
      Linux 3.18-rc2 · cac7f242
      Linus Torvalds authored
      cac7f242
    • Linus Torvalds's avatar
      Merge tag 'armsoc-for-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc · 88e23761
      Linus Torvalds authored
      Pull ARM SoC fixes from Olof Johansson:
       "Another week, another small batch of fixes.
      
        Most of these make zynq, socfpga and sunxi platforms work a bit
        better:
      
         - due to new requirements for regulators, DWMMC on socfpga broke past
           v3.17
         - SMP spinup fix for socfpga
         - a few DT fixes for zynq
         - another option (FIXED_REGULATOR) for sunxi is needed that used to
           be selected by other options but no longer is.
         - a couple of small DT fixes for at91
         - ...and a couple for i.MX"
      
      * tag 'armsoc-for-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
        ARM: dts: imx28-evk: Let i2c0 run at 100kHz
        ARM: i.MX6: Fix "emi" clock name typo
        ARM: multi_v7_defconfig: enable CONFIG_MMC_DW_ROCKCHIP
        ARM: sunxi_defconfig: enable CONFIG_REGULATOR_FIXED_VOLTAGE
        ARM: dts: socfpga: Add a 3.3V fixed regulator node
        ARM: dts: socfpga: Fix SD card detect
        ARM: dts: socfpga: rename gpio nodes
        ARM: at91/dt: sam9263: fix PLLB frequencies
        power: reset: at91-reset: fix power down register
        MAINTAINERS: add atmel ssc driver maintainer entry
        arm: socfpga: fix fetching cpu1start_addr for SMP
        ARM: zynq: DT: trivial: Fix mc node
        ARM: zynq: DT: Add cadence watchdog node
        ARM: zynq: DT: Add missing reference for memory-controller
        ARM: zynq: DT: Add missing reference for ADC
        ARM: zynq: DT: Add missing address for L2 pl310
        ARM: zynq: DT: Remove 222 MHz OPP
        ARM: zynq: DT: Fix GEM register area size
      88e23761
    • Linus Torvalds's avatar
      Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs · d1e14f1d
      Linus Torvalds authored
      Pull vfs updates from Al Viro:
       "overlayfs merge + leak fix for d_splice_alias() failure exits"
      
      * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
        overlayfs: embed middle into overlay_readdir_data
        overlayfs: embed root into overlay_readdir_data
        overlayfs: make ovl_cache_entry->name an array instead of pointer
        overlayfs: don't hold ->i_mutex over opening the real directory
        fix inode leaks on d_splice_alias() failure exits
        fs: limit filesystem stacking depth
        overlay: overlay filesystem documentation
        overlayfs: implement show_options
        overlayfs: add statfs support
        overlay filesystem
        shmem: support RENAME_WHITEOUT
        ext4: support RENAME_WHITEOUT
        vfs: add RENAME_WHITEOUT
        vfs: add whiteout support
        vfs: export check_sticky()
        vfs: introduce clone_private_mount()
        vfs: export __inode_permission() to modules
        vfs: export do_splice_direct() to modules
        vfs: add i_op->dentry_open()
      d1e14f1d
    • Olof Johansson's avatar
      Merge tag 'imx-fixes-3.18' of... · efc176a8
      Olof Johansson authored
      Merge tag 'imx-fixes-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
      
      Merge "ARM: imx: fixes for 3.18" from Shawn Guo:
      
      The i.MX fixes for 3.18:
       - Revert one patch which increases I2C bus frequency on imx28-evk
       - Fix a typo on imx6q EIM clock name
      
      * tag 'imx-fixes-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
        ARM: dts: imx28-evk: Let i2c0 run at 100kHz
        ARM: i.MX6: Fix "emi" clock name typo
      Signed-off-by: default avatarOlof Johansson <olof@lixom.net>
      efc176a8