CP2104 and the ECI interface of CP2105 support further baud rates than
the ones specified in AN205 table 1, and we can use the same equations
as for CP2102N to determine and report back the actual baud rates used.

Note that this could eventually be generalised also to CP2108, which
uses a different base clock. There appears to be an error in the CP2108
equations which needs to be confirmed on actual hardware first however
(specifically, the subtraction of one from the divisor appears to be
incorrect as it introduces larger errors).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

The CP2102N equations for determining the actual baud rate can be used
also for other device types, so let's factor it out.

Note that this removes the now unused cp210x_is_cp2102n() helper.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

CP2102N devices support a lot more baudrates than earlier chips by
SiLabs. These devices are not constrained anymore by the table in AN205,
and are able to generate almost any baudrate in the supported range
with only minimal errors. This has also been verified with a scope on
a physical device. This patch adds support for all baudrates supported
by the CP2102N.
Signed-off-by: Karoly Pados <pados@pados.hu>
[johan: rework on top of an205 and max-speed patches ]
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Newer cp210x devices support higher line speeds than the older ones
which supported a discrete set of speeds up to 921.6 kbaud.

To support these higher speeds, we have for some time mapped speeds
lower than 1 Mbaud to the speeds supported by older devices, while
allowing the device to pick the closest possible rate for higher speeds
(without trying to guess and report back what rate was actually chosen).

As this implementation can lead to undefined behaviour for older devices
which do not support the higher rates, let's use the later-added
device-type detection to determine the maximum supported speed.

This will also be useful when adding support for cp2102n which can
handle rates up to 3 Mbaud.

As per the data sheets the following maximum speeds are used

	cp2101		921.6 kbaud
	cp2102/3	1 Mbaud
	cp2104/8	2 Mbaud
	cp2105
	 - ECI port	2 Mbaud
	 - SCI port	921.6 kbaud

while keeping the maximum 2 Mbaud for unknown device types in order to
avoid any regressions.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Older cp210x devices only support a fixed set of line speeds to which a
requested speed is mapped. Reimplement this mapping using a table
instead of a long if-else construct.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Drop redundant input-speed re-encoding at every open(). The output and
input speeds are initialised to the same value and are kept in sync on
termios updates.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Drop unused driver-data baud rate.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Variables iflag, mask and serial are being assigned but are never used
hence are redundant and can be removed.

Cleans up clang warnings:
warning: variable 'iflag' set but not used [-Wunused-but-set-variable]
warning: variable 'mask' set but not used [-Wunused-but-set-variable]
warning: variable 'serial' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Johan Hovold <johan@kernel.org>

Remove references to long-gone kl5kusb105 module parameters in the
usb-serial documentation.
Signed-off-by: Johan Hovold <johan@kernel.org>

This driver was apparently never tested with an actual KLSI device. In
fact, even the device-id entry which was supposed to allow for this had
a typo in it.

Tests now reveal that the predicted firmware differences with the
PalmConnect adapters are real and that the driver does not support KLSI
devices with PID 0x000c, so let's remove the broken entry.
Reported-by: Chris Jakob <chris.jakob@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>

Add missing version-request error handling and suppress printing of the
(zeroed) transfer-buffer content in case of errors.
Signed-off-by: Johan Hovold <johan@kernel.org>

Make sure to return -EIO in case of a short modem-status read request.

While at it, split the debug message to not include the (zeroed)
transfer-buffer content in case of errors.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>

Add a "tty_" prefix to the tty "flag" variable to avoid any future
mixups with the recently added irq-mask "flags" one.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>

The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>

The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>

The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>

The portdata spinlock can be taken in interrupt context (via
sierra_outdat_callback()).
Disable interrupts when taking the portdata spinlock when discarding
deferred URBs during close to prevent a possible deadlock.

Fixes: 014333f7 ("USB: sierra: fix urb and memory leak on disconnect")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
[ johan: amend commit message and add fixes and stable tags ]
Signed-off-by: Johan Hovold <johan@kernel.org>

The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>

The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>

The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>

The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>

The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>

The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>

The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>

Negative error code will be larger than sizeof().

Note that none of these bugs prevent errors from being detected, even if
the ir-usb one would cause a less precise debug message to printed.
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
[ johan: add comment about implications ]
Signed-off-by: Johan Hovold <johan@kernel.org>

Pull perf fixes from Thomas Gleixner:
 "A pile of perf updates:

  Kernel side:

   - Remove an incorrect warning in uprobe_init_insn() when
     insn_get_length() fails. The error return code is handled at the
     call site.

   - Move the inline keyword to the right place in the perf ringbuffer
     code to address a W=1 build warning.

  Tooling:

  perf stat:

   - Fix metric column header display alignment

   - Improve error messages for default attributes, providing better
     output for error in command line.

   - Add --interval-clear option, to provide a 'watch' like printing

  perf script:

   - Show hw-cache events too

  perf c2c:

   - Fix data dependency problem in layout of 'struct c2c_hist_entry'

  Core:

   - Do not blindly assume that 'struct perf_evsel' can be obtained via
     a straight forward container_of() as there are call sites which
     hand in a plain 'struct hist' which is not part of a container.

   - Fix error index in the PMU event parser, so that error messages can
     point to the problematic token"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/core: Move the inline keyword at the beginning of the function declaration
  uprobes/x86: Remove incorrect WARN_ON() in uprobe_init_insn()
  perf script: Show hw-cache events
  perf c2c: Keep struct hist_entry at the end of struct c2c_hist_entry
  perf stat: Add event parsing error handling to add_default_attributes
  perf stat: Allow to specify specific metric column len
  perf stat: Fix metric column header display alignment
  perf stat: Use only color_fprintf call in print_metric_only
  perf stat: Add --interval-clear option
  perf tools: Fix error index for pmu event parser
  perf hists: Reimplement hists__has_callchains()
  perf hists browser gtk: Use hist_entry__has_callchains()
  perf hists: Make hist_entry__has_callchains() work with 'perf c2c'
  perf hists: Save the callchain_size in struct hist_entry

Pull rseq fixes from Thomas Gleixer:
 "A pile of rseq related fixups:

   - Prevent infinite recursion when delivering SIGSEGV

   - Remove the abort of rseq critical section on fork() as syscalls
     inside rseq critical sections are explicitely forbidden. So no
     point in doing the abort on the child.

   - Align the rseq structure on 32 bytes in the ARM selftest code.

   - Fix file permissions of the test script"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  rseq: Avoid infinite recursion when delivering SIGSEGV
  rseq/cleanup: Do not abort rseq c.s. in child on fork()
  rseq/selftests/arm: Align 'struct rseq_cs' on 32 bytes
  rseq/selftests: Make run_param_test.sh executable

Pull EFI fixes from Thomas Gleixner:
 "Two fixlets for the EFI maze:

   - Properly zero variables to prevent an early boot hang on EFI mixed
     mode systems

   - Fix the fallout of merging the 32bit and 64bit variants of EFI PCI
     related code which ended up chosing the 32bit variant of the actual
     EFi call invocation which leads to failures on 64bit"

* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  efi/x86: Fix incorrect invocation of PciIo->Attributes()
  efi/libstub/tpm: Initialize efi_physical_addr_t vars to zero for mixed mode

Pull core fixes from Thomas Gleixner:
 "Two tiny fixes:

   - Add the missing machine_real_restart() to objtools noreturn list so
     it stops complaining

   - Fix a trivial comment typo"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  kernel.h: Fix a typo in comment
  objtool: Add machine_real_restart() to the noreturn list

Pull x86 fixes from Thomas Gleixner:
 "A set of fixes for x86:

   - Make Xen PV guest deal with speculative store bypass correctly

   - Address more fallout from the 5-Level pagetable handling. Undo an
     __initdata annotation to avoid section mismatch and malfunction
     when post init code would touch the freed variable.

   - Handle exception fixup in math_error() before calling notify_die().
     The reverse call order incorrectly triggers notify_die() listeners
     for soemthing which is handled correctly at the site which issues
     the floating point instruction.

   - Fix an off by one in the LLC topology calculation on AMD

   - Handle non standard memory block sizes gracefully un UV platforms

   - Plug a memory leak in the microcode loader

   - Sanitize the purgatory build magic

   - Add the x86 specific device tree bindings directory to the x86
     MAINTAINER file patterns"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm: Fix 'no5lvl' handling
  Revert "x86/mm: Mark __pgtable_l5_enabled __initdata"
  x86/CPU/AMD: Fix LLC ID bit-shift calculation
  MAINTAINERS: Add file patterns for x86 device tree bindings
  x86/microcode/intel: Fix memleak in save_microcode_patch()
  x86/platform/UV: Add kernel parameter to set memory block size
  x86/platform/UV: Use new set memory block size function
  x86/platform/UV: Add adjustable set memory block size function
  x86/build: Remove unnecessary preparation for purgatory
  Revert "kexec/purgatory: Add clean-up for purgatory directory"
  x86/xen: Add call of speculative_store_bypass_ht_init() to PV paths
  x86: Call fixup_exception() before notify_die() in math_error()

Pull x86 pti fixes from Thomas Gleixner:
 "Two small updates for the speculative distractions:

   - Make it more clear to the compiler that array_index_mask_nospec()
     is not subject for optimizations. It's not perfect, but ...

   - Don't report XEN PV guests as vulnerable because their mitigation
     state depends on the hypervisor. Report unknown and refer to the
     hypervisor requirement"

* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/spectre_v1: Disable compiler optimizations over array_index_mask_nospec()
  x86/pti: Don't report XenPV as vulnerable

Pull locking fixes from Thomas Gleixner:
 "A set of fixes and updates for the locking code:

   - Prevent lockdep from updating irq state within its own code and
     thereby confusing itself.

   - Buid fix for older GCCs which mistreat anonymous unions

   - Add a missing lockdep annotation in down_read_non_onwer() which
     causes up_read_non_owner() to emit a lockdep splat

   - Remove the custom alpha dec_and_lock() implementation which is
     incorrect in terms of ordering and use the generic one.

  The remaining two commits are not strictly fixes. They provide irqsave
  variants of atomic_dec_and_lock() and refcount_dec_and_lock(). These
  are required to merge the relevant updates and cleanups into different
  maintainer trees for 4.19, so routing them into mainline without
  actual users is the sanest approach.

  They should have been in -rc1, but last weekend I took the liberty to
  just avoid computers in order to regain some mental sanity"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/qspinlock: Fix build for anonymous union in older GCC compilers
  locking/lockdep: Do not record IRQ state within lockdep code
  locking/rwsem: Fix up_read_non_owner() warning with DEBUG_RWSEMS
  locking/refcounts: Implement refcount_dec_and_lock_irqsave()
  atomic: Add irqsave variant of atomic_dec_and_lock()
  alpha: Remove custom dec_and_lock() implementation

Pull ras fixes from Thomas Gleixner:
 "A set of fixes for RAS/MCE:

   - Improve the error message when the kernel cannot recover from a MCE
     so the maximum amount of information gets provided.

   - Individually check MCE recovery features on SkyLake CPUs instead of
     assuming none when the CAPID0 register does not advertise the
     general ability for recovery.

   - Prevent MCE to output inconsistent messages which first show an
     error location and then claim that the source is unknown.

   - Prevent overwriting MCi_STATUS in the attempt to gather more
     information when a fatal MCE has alreay been detected. This leads
     to empty status values in the printout and failing to react
     promptly on the fatal event"

* 'ras-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mce: Fix incorrect "Machine check from unknown source" message
  x86/mce: Do not overwrite MCi_STATUS in mce_no_way_out()
  x86/mce: Check for alternate indication of machine check recovery on Skylake
  x86/mce: Improve error message when kernel cannot recover

Pull timer fixes from Thomas Gleixner:
 "A small set of fixes for time(r) related issues:

   - Fix a long standing conversion issue in jiffies_to_msecs() for odd
     HZ values like 1024 or 1200 which resulted in returning 0 for small
     jiffies values due to rounding down.

   - Use the proper CONFIG symbol in the new Y2038 safe compat code for
     posix-timers. Not yet a visible breakage, but this will immediately
     trigger when the architecture support for the new interfaces is
     merged.

   - Return an error code in the STM32 clocksource driver on failure
     instead of success.

   - Remove the redundant and stale irq disabled check in the posix cpu
     timer code. The check is at the wrong place anyway and lockdep
     already covers it via the sighand lock locking coverage"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  time: Make sure jiffies_to_msecs() preserves non-zero time periods
  posix-timers: Fix nanosleep_copyout() for CONFIG_COMPAT_32BIT_TIME
  clocksource/drivers/stm32: Fix error return code
  posix-cpu-timers: Remove lockdep_assert_irqs_disabled()

Pull irq fixes from Thomas Gleixner:
 "A set of fixes mostly for the ARM/GIC world:

   - Fix the MSI affinity handling in the ls-scfg irq chip driver so it
     updates and uses the effective affinity mask correctly

   - Prevent binding LPIs to offline CPUs and respect the Cavium erratum
     which requires that LPIs which belong to an offline NUMA node are
     not bound to a CPU on a different NUMA node.

   - Free only the amount of allocated interrupts in the GIC-V2M driver
     instead of trying to free log2(nrirqs).

   - Prevent emitting SYNC and VSYNC targetting non existing interrupt
     collections in the GIC-V3 ITS driver

   - Ensure that the GIV-V3 interrupt redistributor is correctly
     reprogrammed on CPU hotplug

   - Remove a stale unused helper function"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqdesc: Delete irq_desc_get_msi_desc()
  irqchip/gic-v3-its: Fix reprogramming of redistributors on CPU hotplug
  irqchip/gic-v3-its: Only emit VSYNC if targetting a valid collection
  irqchip/gic-v3-its: Only emit SYNC if targetting a valid collection
  irqchip/gic-v3-its: Don't bind LPI to unavailable NUMA node
  irqchip/gic-v2m: Fix SPI release on error path
  irqchip/ls-scfg-msi: Fix MSI affinity handling
  genirq/debugfs: Add missing IRQCHIP_SUPPORTS_LEVEL_MSI debug

Pull MIPS fixes from Paul Burton:
 "A few MIPS fixes for 4.18:

   - a GPIO device name fix for a regression in v4.15-rc1.

   - an errata workaround for the BCM5300X platform.

   - a fix to ftrace function graph tracing, broken for a long time with
     the fix applying cleanly back as far as v3.17.

   - addition of read barriers to in{b,w,l,q}() functions, matching
     behavior of other architectures & mirroring the equivalent addition
     to read{b,w,l,q} in v4.17-rc2.

  Plus changes to wire up new syscalls introduced in the 4.18 cycle:

   - Restartable sequences support is added, including MIPS support in
     the selftests.

   - io_pgetevents is wired up"

* tag 'mips_fixes_4.18_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
  MIPS: Wire up io_pgetevents syscall
  rseq/selftests: Implement MIPS support
  MIPS: Wire up the restartable sequences (rseq) syscall
  MIPS: Add syscall detection for restartable sequences
  MIPS: Add support for restartable sequences
  MIPS: io: Add barrier after register read in inX()
  mips: ftrace: fix static function graph tracing
  MIPS: BCM47XX: Enable 74K Core ExternalSync for PCIe erratum
  MIPS: pb44: Fix i2c-gpio GPIO descriptor table

The following commit:

  2c3625cb ("efi/x86: Fold __setup_efi_pci32() and __setup_efi_pci64() into one function")

... merged the two versions of __setup_efi_pciXX(), without taking into
account that the 32-bit version used a rather dodgy trick to pass an
immediate 0 constant as argument for a uint64_t parameter.

The issue is caused by the fact that on x86, UEFI protocol method calls
are redirected via struct efi_config::call(), which is a variadic function,
and so the compiler has to infer the types of the parameters from the
arguments rather than from the prototype.

As the 32-bit x86 calling convention passes arguments via the stack,
passing the unqualified constant 0 twice is the same as passing 0ULL,
which is why the 32-bit code in __setup_efi_pci32() contained the
following call:

  status = efi_early->call(pci->attributes, pci,
                           EfiPciIoAttributeOperationGet, 0, 0,
                           &attributes);

to invoke this UEFI protocol method:

  typedef
  EFI_STATUS
  (EFIAPI *EFI_PCI_IO_PROTOCOL_ATTRIBUTES) (
    IN  EFI_PCI_IO_PROTOCOL                     *This,
    IN  EFI_PCI_IO_PROTOCOL_ATTRIBUTE_OPERATION Operation,
    IN  UINT64                                  Attributes,
    OUT UINT64                                  *Result OPTIONAL
    );

After the merge, we inadvertently ended up with this version for both
32-bit and 64-bit builds, breaking the latter.

So replace the two zeroes with the explicitly typed constant 0ULL,
which works as expected on both 32-bit and 64-bit builds.

Wilfried tested the 64-bit build, and I checked the generated assembly
of a 32-bit build with and without this patch, and they are identical.
Reported-by: Wilfried Klaebe <linux-kernel@lebenslange-mailadresse.de>
Tested-by: Wilfried Klaebe <linux-kernel@lebenslange-mailadresse.de>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: hdegoede@redhat.com
Cc: linux-efi@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

Pull block fixes from Jens Axboe:

 - Further timeout fixes. We aren't quite there yet, so expect another
   round of fixes for that to completely close some of the IRQ vs
   completion races. (Christoph/Bart)

 - Set of NVMe fixes from the usual suspects, mostly error handling

 - Two off-by-one fixes (Dan)

 - Another bdi race fix (Jan)

 - Fix nbd reconfigure with NBD_DISCONNECT_ON_CLOSE (Doron)

* tag 'for-linus-20180623' of git://git.kernel.dk/linux-block:
  blk-mq: Fix timeout handling in case the timeout handler returns BLK_EH_DONE
  bdi: Fix another oops in wb_workfn()
  lightnvm: Remove depends on HAS_DMA in case of platform dependency
  nvme-pci: limit max IO size and segments to avoid high order allocations
  nvme-pci: move nvme_kill_queues to nvme_remove_dead_ctrl
  nvme-fc: release io queues to allow fast fail
  nbd: Add the nbd NBD_DISCONNECT_ON_CLOSE config flag.
  block: sed-opal: Fix a couple off by one bugs
  blk-mq-debugfs: Off by one in blk_mq_rq_state_name()
  nvmet: reset keep alive timer in controller enable
  nvme-rdma: don't override opts->queue_size
  nvme-rdma: Fix command completion race at error recovery
  nvme-rdma: fix possible free of a non-allocated async event buffer
  nvme-rdma: fix possible double free condition when failing to create a controller
  Revert "block: Add warning for bi_next not NULL in bio_endio()"
  block: fix timeout changes for legacy request drivers