When the autosuspend is enabled and occurs before system suspend, we should
wake the device before running system syspend. Then, we could change the wake
event for system suspend. Otherwise, the device would resume the system when
receiving any packet.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 651df218 ("phy: micrel: Fix finding PHY properties in MAC
 node.") only fixes finding PHY properties in MAC node for KSZ9021. This
commit applies the same fix for KSZ9031.

Fixes: 8b63ec18 ("phylib: Make PHYs children of their MDIO bus, not the bus' parent.")
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Henri Roosen <henri.roosen@ginzinger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Antonio Quartulli says:

====================
Included change:
- Fix invalid read while copying bat_iv.bcast_own by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

I noticed this code because it has a typo in the module_param(),
the "trs" at the end of "toim3232fliptrs" should be "rts".  But it's
dead code so instead of fixing it, I just deleted it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no "membase", it was "act_port" that was intended.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a bug writing to EEPROM in lan78xx_ethtool_set_eeprom()
when asked to write to OTP.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

batadv_iv_ogm_orig_del_if removes a part of the bcast_own which previously
belonged to the now removed interface. This is done by copying all data
which comes before the removed interface and then appending all the data
which comes after the removed interface.

The address calculation for the position of the data which comes after the
removed interface assumed that the bat_iv.bcast_own is a pointer to a
single byte datatype. But it is a pointer to unsigned long and thus the
calculated position was wrong off factor sizeof(unsigned long).

Fixes: 83a8342678a0 ("more basic routing code added (forwarding packets /
bitarray added)")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>

Pull networking fixes from David Miller:
 "As usual, there are a couple straggler bug fixes:

   1) qlcnic_alloc_mbx_args() error returns are not checked in qlcnic
      driver.  Fix from Insu Yun.

   2) SKB refcounting bug in connector, from Florian Westphal.

   3) vrf_get_saddr() has to propagate fib_lookup() errors to it's
      callers, from David Ahern.

   4) Fix AF_UNIX splice/bind deadlock, from Rainer Weikusat.

   5) qdisc_rcu_free() fails to free the per-cpu qstats.  Fix from John
      Fastabend.

   6) vmxnet3 driver passes wrong page to dma_map_page(), fix from
     Shrikrishna Khare.

   7) Don't allow zero cwnd in tcp_cwnd_reduction(), from Yuchung Cheng"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  tcp: fix zero cwnd in tcp_cwnd_reduction
  Driver: Vmxnet3: Fix regression caused by 5738a09d
  net: qmi_wwan: Add WeTelecom-WPD600N
  mkiss: fix scribble on freed memory
  net: possible use after free in dst_release
  net: sched: fix missing free per cpu on qstats
  ARM: net: bpf: fix zero right shift
  6pack: fix free memory scribbles
  net: filter: make JITs zero A for SKF_AD_ALU_XOR_X
  bridge: Only call /sbin/bridge-stp for the initial network namespace
  af_unix: Fix splice-bind deadlock
  net: Propagate lookup failure in l3mdev_get_saddr to caller
  r8152: add reset_resume function
  connector: bump skb->users before callback invocation
  cxgb4: correctly handling failed allocation
  qlcnic: correctly handle qlcnic_alloc_mbx_args

Patch 3759824d ("tcp: PRR uses CRB mode by default and SS mode
conditionally") introduced a bug that cwnd may become 0 when both
inflight and sndcnt are 0 (cwnd = inflight + sndcnt). This may lead
to a div-by-zero if the connection starts another cwnd reduction
phase by setting tp->prior_cwnd to the current cwnd (0) in
tcp_init_cwnd_reduction().

To prevent this we skip PRR operation when nothing is acked or
sacked. Then cwnd must be positive in all cases as long as ssthresh
is positive:

1) The proportional reduction mode
   inflight > ssthresh > 0

2) The reduction bound mode
  a) inflight == ssthresh > 0

  b) inflight < ssthresh
     sndcnt > 0 since newly_acked_sacked > 0 and inflight < ssthresh

Therefore in all cases inflight and sndcnt can not both be 0.
We check invalid tp->prior_cwnd to avoid potential div0 bugs.

In reality this bug is triggered only with a sequence of less common
events.  For example, the connection is terminating an ECN-triggered
cwnd reduction with an inflight 0, then it receives reordered/old
ACKs or DSACKs from prior transmission (which acks nothing). Or the
connection is in fast recovery stage that marks everything lost,
but fails to retransmit due to local issues, then receives data
packets from other end which acks nothing.

Fixes: 3759824d ("tcp: PRR uses CRB mode by default and SS mode conditionally")
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reported-by: Bingkuo Liu <bingkuol@vmware.com>
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The WeTelecom-WPD600N is an LTE module that, in addition to supporting most
"normal" bands, also supports LTE over 450MHz. Manual testing showed that
only interface number three replies to QMI messages.

Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit d79f16c0 fixed a user triggerable
scribble on free memory but added a new one which allows the user to
scribble even more and user controlled data into freed space.

As with 6pack we need to halt the queue before we free the buffers, because
the transmit logic is not protected by the semaphore.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dst_release should not access dst->flags after decrementing
__refcnt to 0. The dst_entry may be in dst_busy_list and
dst_gc_task may dst_destroy it before dst_release gets a chance
to access dst->flags.

Fixes: d69bbf88 ("net: fix a race in dst_release()")
Fixes: 27b75c95 ("net: avoid RCU for NOCACHE dst")
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a qdisc is using per cpu stats (currently just the ingress
qdisc) only the bstats are being freed. This also free's the qstats.

Fixes: b0ab6f92 ("net: sched: enable per cpu qstats")
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The LSR instruction cannot be used to perform a zero right shift since a
0 as the immediate value (imm5) in the LSR instruction encoding means
that a shift of 32 is perfomed.  See DecodeIMMShift() in the ARM ARM.

Make the JIT skip generation of the LSR if a zero-shift is requested.

This was found using american fuzzy lop.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit acf673a3 fixed a user triggerable free
memory scribble but in doing so replaced it with a different one that allows
the user to control the data and scribble even more.

sixpack_close is called by the tty layer in tty context. The tty context is
protected by sp_get() and sp_put(). However network layer activity via
sp_xmit() is not protected this way. We must therefore stop the queue
otherwise the user gets to dump a buffer mostly of their choice into freed
kernel pages.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The SKF_AD_ALU_XOR_X ancillary is not like the other ancillary data
instructions since it XORs A with X while all the others replace A with
some loaded value.  All the BPF JITs fail to clear A if this is used as
the first instruction in a filter.  This was found using american fuzzy
lop.

Add a helper to determine if A needs to be cleared given the first
instruction in a filter, and use this in the JITs.  Except for ARM, the
rest have only been compile-tested.

Fixes: 34805931 ("net: filter: get rid of BPF_S_* enum")
Signed-off-by: Rabin Vincent <rabin@rab.in>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

[I stole this patch from Eric Biederman. He wrote:]

> There is no defined mechanism to pass network namespace information
> into /sbin/bridge-stp therefore don't even try to invoke it except
> for bridge devices in the initial network namespace.
>
> It is possible for unprivileged users to cause /sbin/bridge-stp to be
> invoked for any network device name which if /sbin/bridge-stp does not
> guard against unreasonable arguments or being invoked twice on the
> same network device could cause problems.

[Hannes: changed patch using netns_eq]

Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull tracing fixes from Steven Rostedt:
 "Two more fixes:

  1. The recordmcount change had an output that used sprintf()
     (incorrectly) when it should have been a fprintf() to stderr.

  2. The printk_formats file could crash if someone added a
     trace_printk() in the core kernel, and also added one in a module.
     This does not affect production kernels.  Only kernels where
     developers add trace_printk() for debugging can crash"

* tag 'trace-v4.4-rc4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Fix setting of start_index in find_next()
  ftrace/scripts: Fix incorrect use of sprintf in recordmcount

Pull tile bugfix from Chris Metcalf:
 "This fixes a bug that Sudip's buildbot found for tilepro allmodconfig.

  I've tagged it for stable only back to 3.19, which was when most of
  the other affected architectures added their support for working
  around this issue"

* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
  tile: provide CONFIG_PAGE_SIZE_64KB etc for tilepro

This allows the build system to know that it can't attempt to
configure the Lustre virtual block device, for example, when tilepro
is using 64KB pages (as it does by default).  The tilegx build
already provided those symbols.

Previously we required that the tilepro hypervisor be rebuilt with
a different hardcoded page size in its headers, and then Linux be
rebuilt using the updated hypervisor header.  Now we allow each of
the hypervisor and Linux to be built independently.  We still check
at boot time to ensure that the page size provided by the hypervisor
matches what Linux expects.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
Cc: stable@vger.kernel.org [3.19+]

On 2015/11/06, Dmitry Vyukov reported a deadlock involving the splice
system call and AF_UNIX sockets,

http://lists.openwall.net/netdev/2015/11/06/24

The situation was analyzed as

(a while ago) A: socketpair()
B: splice() from a pipe to /mnt/regular_file
	does sb_start_write() on /mnt
C: try to freeze /mnt
	wait for B to finish with /mnt
A: bind() try to bind our socket to /mnt/new_socket_name
	lock our socket, see it not bound yet
	decide that it needs to create something in /mnt
	try to do sb_start_write() on /mnt, block (it's
	waiting for C).
D: splice() from the same pipe to our socket
	lock the pipe, see that socket is connected
	try to lock the socket, block waiting for A
B:	get around to actually feeding a chunk from
	pipe to file, try to lock the pipe.  Deadlock.

on 2015/11/10 by Al Viro,

http://lists.openwall.net/netdev/2015/11/10/4

The patch fixes this by removing the kern_path_create related code from
unix_mknod and executing it as part of unix_bind prior acquiring the
readlock of the socket in question. This means that A (as used above)
will sb_start_write on /mnt before it acquires the readlock, hence, it
won't indirectly block B which first did a sb_start_write and then
waited for a thread trying to acquire the readlock. Consequently, A
being blocked by C waiting for B won't cause a deadlock anymore
(effectively, both A and B acquire two locks in opposite order in the
situation described above).

Dmitry Vyukov(<dvyukov@google.com>) tested the original patch.
Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commands run in a vrf context are not failing as expected on a route lookup:
    root@kenny:~# ip ro ls table vrf-red
    unreachable default

    root@kenny:~# ping -I vrf-red -c1 -w1 10.100.1.254
    ping: Warning: source address might be selected on device other than vrf-red.
    PING 10.100.1.254 (10.100.1.254) from 0.0.0.0 vrf-red: 56(84) bytes of data.

    --- 10.100.1.254 ping statistics ---
    2 packets transmitted, 0 received, 100% packet loss, time 999ms

Since the vrf table does not have a route for 10.100.1.254 the ping
should have failed. The saddr lookup causes a full VRF table lookup.
Propogating a lookup failure to the user allows the command to fail as
expected:

    root@kenny:~# ping -I vrf-red -c1 -w1 10.100.1.254
    connect: No route to host
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the reset_resume() is called, the flag of SELECTIVE_SUSPEND should be
cleared and reinitialize the device, whether the SELECTIVE_SUSPEND is set
or not. If reset_resume() is called, it means the power supply is cut or the
device is reset. That is, the device wouldn't be in runtime suspend state and
the reinitialization is necessary.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dmitry reports memleak with syskaller program.
Problem is that connector bumps skb usecount but might not invoke callback.

So move skb_get to where we invoke the callback.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since t4_alloc_mem can be failed in memory pressure,
if not properly handled, NULL dereference could be happened.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since qlcnic_alloc_mbx_args can be failed,
return value should be checked.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we do cat /sys/kernel/debug/tracing/printk_formats, we hit kernel
panic at t_show.

general protection fault: 0000 [#1] PREEMPT SMP
CPU: 0 PID: 2957 Comm: sh Tainted: G W  O 3.14.55-x86_64-01062-gd4acdc7 #2
RIP: 0010:[<ffffffff811375b2>]
 [<ffffffff811375b2>] t_show+0x22/0xe0
RSP: 0000:ffff88002b4ebe80  EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000004
RDX: 0000000000000004 RSI: ffffffff81fd26a6 RDI: ffff880032f9f7b1
RBP: ffff88002b4ebe98 R08: 0000000000001000 R09: 000000000000ffec
R10: 0000000000000000 R11: 000000000000000f R12: ffff880004d9b6c0
R13: 7365725f6d706400 R14: ffff880004d9b6c0 R15: ffffffff82020570
FS:  0000000000000000(0000) GS:ffff88003aa00000(0063) knlGS:00000000f776bc40
CS:  0010 DS: 002b ES: 002b CR0: 0000000080050033
CR2: 00000000f6c02ff0 CR3: 000000002c2b3000 CR4: 00000000001007f0
Call Trace:
 [<ffffffff811dc076>] seq_read+0x2f6/0x3e0
 [<ffffffff811b749b>] vfs_read+0x9b/0x160
 [<ffffffff811b7f69>] SyS_read+0x49/0xb0
 [<ffffffff81a3a4b9>] ia32_do_call+0x13/0x13
 ---[ end trace 5bd9eb630614861e ]---
Kernel panic - not syncing: Fatal exception

When the first time find_next calls find_next_mod_format, it should
iterate the trace_bprintk_fmt_list to find the first print format of
the module. However in current code, start_index is smaller than *pos
at first, and code will not iterate the list. Latter container_of will
get the wrong address with former v, which will cause mod_fmt be a
meaningless object and so is the returned mod_fmt->fmt.

This patch will fix it by correcting the start_index. After fixed,
when the first time calls find_next_mod_format, start_index will be
equal to *pos, and code will iterate the trace_bprintk_fmt_list to
get the right module printk format, so is the returned mod_fmt->fmt.

Link: http://lkml.kernel.org/r/5684B900.9000309@intel.com

Cc: stable@vger.kernel.org # 3.12+
Fixes: 102c9323 "tracing: Add __tracepoint_string() to export string pointers"
Signed-off-by: Qiu Peiyang <peiyangx.qiu@intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

Fix build warning:

scripts/recordmcount.c:589:4: warning: format not a string
literal and no format arguments [-Wformat-security]
    sprintf("%s: failed\n", file);

Fixes: a50bd439 ("ftrace/scripts: Have recordmcount copy the object file")
Link: http://lkml.kernel.org/r/1451516801-16951-1-git-send-email-colin.king@canonical.com

Cc: Li Bin <huawei.libin@huawei.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org # 2.6.37+
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

Pull MIPS build fix from Ralf Baechle:
 "Fix a makefile issue resulting in build breakage with older binutils.

  This has sat in -next for a few days, testers and buildbot are happy
  with it, too though if you are going for another -rc that'd certainly
  help ironing out a few more issues"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: VDSO: Fix build error with binutils 2.24 and earlier

Pull i915 drm fixes from Jani Nikula:
 "Two display fixes still for v4.4.

  The new year's resolution is to start using signed tags per Linus'
  request.  This one is still unsigned; I want to fix this up in our
  maintainer scripts instead of doing it one-off"

* tag 'drm-intel-fixes-2016-01-02' of git://anongit.freedesktop.org/drm-intel:
  drm/i915: increase the tries for HDMI hotplug live status checking
  drm/i915: Unbreak check_digital_port_conflicts()

Pull PCI bugfix from Bjorn Helgaas:
 "Here's another fix for v4.4.

  This fixes 32-bit config reads for the HiSilicon driver.  Obviously
  the driver is completely broken without this fix (apparently it
  actually was tested internally, but got broken somehow in the process
  of upstreaming it).

  Summary:

  HiSilicon host bridge driver
    Fix 32-bit config reads (Dongdong Liu)"

* tag 'pci-v4.4-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: hisi: Fix hisi_pcie_cfg_read() 32-bit reads

Pull sparc fixes from David Miller:
 "Just some missing syscall wire ups"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc: Wire up mlock2 system call.
  sparc: Add all necessary direct socket system calls.

Pull networking fixes from David Miller:

 1) Prevent XFRM per-cpu counter updates for one namespace from being
    applied to another namespace.  Fix from DanS treetman.

 2) Fix RCU de-reference in iwl_mvm_get_key_sta_id(), from Johannes
    Berg.

 3) Remove ethernet header assumption in nft_do_chain_netdev(), from
    Pablo Neira Ayuso.

 4) Fix cpsw PHY ident with multiple slaves and fixed-phy, from Pascal
    Speck.

 5) Fix use after free in sixpack_close and mkiss_close.

 6) Fix VXLAN fw assertion on bnx2x, from Yuval Mintz.

 7) natsemi doesn't check for DMA mapping errors, from Alexey
    Khoroshilov.

 8) Fix inverted test in ip6addrlbl_get(), from ANdrey Ryabinin.

 9) Missing initialization of needed_headroom in geneve tunnel driver,
    from Paolo Abeni.

10) Fix conntrack template leak in openvswitch, from Joe Stringer.

11) Mission initialization of wq->flags in sock_alloc_inode(), from
    Nicolai Stange.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits)
  sctp: sctp should release assoc when sctp_make_abort_user return NULL in sctp_close
  net, socket, socket_wq: fix missing initialization of flags
  drivers: net: cpsw: fix error return code
  openvswitch: Fix template leak in error cases.
  sctp: label accepted/peeled off sockets
  sctp: use GFP_USER for user-controlled kmalloc
  qlcnic: fix a loop exit condition better
  net: cdc_ncm: avoid changing RX/TX buffers on MTU changes
  geneve: initialize needed_headroom
  ipv6: honor ifindex in case we receive ll addresses in router advertisements
  addrconf: always initialize sysctl table data
  ipv6/addrlabel: fix ip6addrlbl_get()
  switchdev: bridge: Pass ageing time as clock_t instead of jiffies
  sh_eth: fix 16-bit descriptor field access endianness too
  veth: don’t modify ip_summed; doing so treats packets with bad checksums as good.
  net: usb: cdc_ncm: Adding Dell DW5813 LTE AT&T Mobile Broadband Card
  net: usb: cdc_ncm: Adding Dell DW5812 LTE Verizon Mobile Broadband Card
  natsemi: add checks for dma mapping errors
  rhashtable: Kill harmless RCU warning in rhashtable_walk_init
  openvswitch: correct encoding of set tunnel action attributes
  ...

Signed-off-by: David S. Miller <davem@davemloft.net>

The GLIBC folks would like to eliminate socketcall support
eventually, and this makes sense regardless so wire them
all up.
Signed-off-by: David S. Miller <davem@davemloft.net>

In sctp_close, sctp_make_abort_user may return NULL because of memory
allocation failure. If this happens, it will bypass any state change
and never free the assoc. The assoc has no chance to be freed and it
will be kept in memory with the state it had even after the socket is
closed by sctp_close().

So if sctp_make_abort_user fails to allocate memory, we should abort
the asoc via sctp_primitive_ABORT as well. Just like the annotation in
sctp_sf_cookie_wait_prm_abort and sctp_sf_do_9_1_prm_abort said,
"Even if we can't send the ABORT due to low memory delete the TCB.
This is a departure from our typical NOMEM handling".

But then the chunk is NULL (low memory) and the SCTP_CMD_REPLY cmd would
dereference the chunk pointer, and system crash. So we should add
SCTP_CMD_REPLY cmd only when the chunk is not NULL, just like other
places where it adds SCTP_CMD_REPLY cmd.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2015-12-28' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
iwlwifi

* don't load firmware that won't exist for 7260
* fix RCU splat
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit ceb5d58b ("net: fix sock_wake_async() rcu protection") from
the current 4.4 release cycle introduced a new flags member in
struct socket_wq and moved SOCKWQ_ASYNC_NOSPACE and SOCKWQ_ASYNC_WAITDATA
from struct socket's flags member into that new place.

Unfortunately, the new flags field is never initialized properly, at least
not for the struct socket_wq instance created in sock_alloc_inode().

One particular issue I encountered because of this is that my GNU Emacs
failed to draw anything on my desktop -- i.e. what I got is a transparent
window, including the title bar. Bisection lead to the commit mentioned
above and further investigation by means of strace told me that Emacs
is indeed speaking to my Xorg through an O_ASYNC AF_UNIX socket. This is
reproducible 100% of times and the fact that properly initializing the
struct socket_wq ->flags fixes the issue leads me to the conclusion that
somehow SOCKWQ_ASYNC_WAITDATA got set in the uninitialized ->flags,
preventing my Emacs from receiving any SIGIO's due to data becoming
available and it got stuck.

Make sock_alloc_inode() set the newly created struct socket_wq's ->flags
member to zero.

Fixes: ceb5d58b ("net: fix sock_wake_async() rcu protection")
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>