Add the necessary change for AR6004 1.2 chip support
Signed-off-by: Ray Chen <raychen@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Currently rsn capability is not set when it is not available in
rsn IE. Set it to 0 in firmware when it is not there in the ie to
make sure host and target are consistent.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

alignment is not taken care in accessing pairwise cipher and AKM suite
count which are parsed from rsn ie. Fix this alignment issue.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

If an ath6kl AP vif is beaconing on one channel, and a STA vif
associates on a different channel, a WMI_DISCONNECT event will be sent
to the AP vif. Make the AP vif follow the STA interface, and notify
userspace.

kvalo: fix a sparse warning with vif->next_chan
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This is workaround H/W or F/W bug, see in code comments. Without the fix
ping can receive duplicated ICMP frames while associated with legacy AP.
Reported-by: Walter Goldens <goldenstranger@yahoo.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Driver does not use it any more.
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

and all referenced structs and corresponding enums because the driver
does not use it.

Note: keep libipw_info_element struct since it is still in use.
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The firmware may decide to switch channels while already beaconing, e.g.
in response to a cfg80211 connect request on a different vif. Add this
event to notify userspace when an AP or GO interface has successfully
migrated to a new channel, so it can update its configuration
accordingly.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Remove extraneous statements from ath5k_hw_proc_4word_tx_status and ath5k_hw_proc_2word_status.
Signed-off-by: Qasim Javed <qasimj@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In WoWLAN, we only get the triggers when we actually get
to suspend. As a consequence, drivers currently don't
know that the device should enable wakeup. However, the
device_set_wakeup_enable() API is intended to be called
when the wakeup is enabled, not later when needed.

Add a new set_wakeup() call to cfg80211 and mac80211 to
allow drivers to properly call device_set_wakeup_enable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Semicolons are not necessary after macros that end in while (0).
Remove them.

Simplify the macros with tests of
do { if (foo>size) memset1; else memset2;} while (0);
to a single line memset(,,min_t(size_t, foo, size))
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This adds counters in various places that can drop packets on
rx without otherwise incrementing a counter.  It also counts
some non-error cases, such as becons and fragments received.

Should help with figuring out where packets are (and are not)
dropped.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This counts any failure during getting packets into
the DMA buffers, including out-of-memory, etc.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Follow updates in DFS pattern detector interface:
a) use given pulse event structure
b) adapt to boolean return value of add_pulse()
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This adds a DFS pattern detector to ath9k. It is fed with pulse events
by the radar pulse detector and reports in place whether a pattern
was detected. On detection, the result is reported as radar event to
the DFS management component in the upper layer.

Currently the ETSI DFS domain is supported with detector lines for
the patterns defined by EN-301-893 v1.5.1. Support for FCC and JP
will be added gradually.

To include the pattern detector, ath9k must be built with support
for DFS certified config flag set (CONFIG_ATH9K_DFS_CERTIFIED).
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Eliad's comment prompted me to look closer at
the error paths in ieee80211_do_open() and I
found one that should use the error labels.

Also add a comment about the clear_bit since
in many error cases the bit hasn't been set.

Cc: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211 currently only supports one hardware queue
per AC. This is already problematic for off-channel
uses since if we go off channel while the BE queue
is full and then try to send an off-channel frame
the frame will never go out. This will become worse
when we support multi-channel since then a queue on
one channel might be full, but we have to stop the
software queue for all channels. That is obviously
not desirable.

To address this problem allow drivers to register
more hardware queues, and allow them to map them to
virtual interfaces. When they stop a hardware queue
the corresponding AC software queues on the correct
interfaces will be stopped as well. Additionally,
there's an off-channel queue to solve that problem
and a per-interface after-DTIM beacon queue. This
allows drivers to manage software queues closer to
how the hardware works.

Currently, there's a limit of 16 hardware queues.
This may or may not be sufficient, we can adjust it
as needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The queue mapping redesign that I'm planning to do
will break pure injection unless we handle monitor
interfaces explicitly. One possible option would
be to have the driver tell mac80211 about monitor
mode queues etc., but that would duplicate the API
since we already need to have queue assignments
handled per virtual interface.

So in order to solve this, have a virtual monitor
interface that is added whenever all active vifs
are monitors. We could also use the state of one
of the monitor interfaces, but managing that would
be complicated, so allocate separate state.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The AP netdev is really only active when beaconing, so
manage the carrier state accordingly. Also do that for
VLAN interfaces enslaved to a given AP interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Section 13.2.3 of IEEE 80211s standard requires BSSBasicRateSet of mesh nodes
to be identical to establish peer link.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Basic rates are added with supported rates IE and extended supported
rates IE.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is needed when we are concted to non 11n AP.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The driver now claims to support IBSS/RSN. Group key configuration in hardware
is skipped. Software encryption is used for multicast communications.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Report Toffset to userspace.
Let userspace select the mesh synchronization method.
Signed-off-by: Marco Porsch <marco.porsch@s2005.tu-chemnitz.de>
Signed-off-by: Pavel Zubarev <pavel.zubarev@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds MBSS extensible synchronization framework (Sec.
13.13.2 of IEEE Std. 802.11-2012).

The framework is implemented via an ops table which defines the
following functions:

    rx_bcn_presp() - this is called every time a mesh beacon is
received.
    adjust_tbtt() - this is called immediately before a beacon is about
to be transmitted.

The default neighbor offset synchronization defined in the standard is
implemented.  We also provide template functions for vendor specific
methods.

When neighbor offset synchronization is active (which is the default)
mesh neighbors in the same MBSS will track timing offsets to each other
and compensate clock drift.

In our tests we observed that this mesh synchronization implementation
successfully corrected drifts between stations of ~2PPM while
introducing a jitter of ~20us.

It is also possible to test this framework on mac80211_hwsim simulated
phys to see how it behaves under different topologies, over poor links,
etc.
Signed-off-by: Marco Porsch <marco.porsch@s2005.tu-chemnitz.de>
Signed-off-by: Pavel Zubarev <pavel.zubarev@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Reading and writing back the tsf value via tsf is too slow if one wants
to make small increments to this timer.  With this change you can use
the syntax "+=<some value>" or "-=<some value>" to add or substract a
value from the tsf counter.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Generate more acurate tsf values in hwsim by setting the tsf value on
trasmitted beacons immediately before they are moved to the rx path.
Also, adjust the beacon timestamp to be the time at which the first byte
of the timestamp is transmitted.

With these changes the observed tsf offset between two hwsim/mesh peers
is 0 (unless the offset is modified via debugfs)
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

While associated we should never have empty SSID, but life can be full
of surprises, and is allways better to print a warning than crash.

Before memcpy() in ieee80211_probereq_get() check ssid_len instead of
ssid pointer, sice pointer it always passed by "ssidie + 2" expression
to send probe functions, so practically never can be NULL.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When comparing hw->queues to determine if the
device is QoS capable, use IEEE80211_NUM_ACS
instead of just 4.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When adding pending SKBs there's no need to
stop all queues, we only need to stop those
that we're adding frames to. Implement that
by lazily stopping a queue as we add an SKB.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When the queue status changes we need to do a fair
bit of work, so ignore no-op changes early.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When we get more hardware queues, we'll still want
to only have netdev queues per AC, so set it up in
that way. If the hardware doesn't support QoS (by
not supporting at least 4 queues) the netdevs get
a single queue only (this is no change in behavior
as there are no drivers with 2 or 3 queues today.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Drivers that don't support QoS also don't support
setting up their ACs, catch that early. While at
it, remove the input check since cfg80211 does it
now.

Also fix up the restart code to not try to set up
the queues in this case.

Finally also change the tx_conf array to have
IEEE80211_NUM_ACS entries instead of # of queues
since that's what it really needs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

With the plan to change mac80211's queue API to
not map ACs to queues 1:1, it seems necessary to
clarify some APIs that act on ACs rather than on
queues to spell that out explicitly. Do this.

Also verify that the AC number given is valid.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This field is never set to anything non-zero in
mac80211, so we should be able to remove it.
Unfortunately though, the iwlwifi and iwlegacy
drivers use it for their internal TX status
processing (which shouldn't be using the rate
control API to start with), so add a new field
"status.antenna" for them, at least for now.

In the future, I plan to use the new field to
hold the hardware queue, while the SKB's queue
mapping holds the AC.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Devices that have internal rate control need to be
notified when the bandwidth or SMPS state changes
just like external rate control algorithms get a
notification now.

Add this notification and clarify the change bits
while at it, the HT_CHANGED bit really meant only
bandwidth changed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>