- 30 Jun, 2012 1 commit
-
-
Mauro Carvalho Chehab authored
Change the firmware logic to use request_firmware_nowait(), and to preserve the loaded firmwares in memory, to reduce the risk of troubles with buggy userspace apps. With this change, while the firmware is being loaded, the driver will return -EAGAIN to any calls. If, for some reason, firmware failed to be loaded from userspace, it will return -ENODEV. Signed-off-by:Mauro Carvalho Chehab <mchehab@redhat.com>
-
- 29 Jun, 2012 5 commits
-
-
Mauro Carvalho Chehab authored
If firmware is not loaded for some reason, or if it is not ready yet, it makes no sense to honour to any DVB callbacks. So, return -EAGAIN, as the error condition may be temporary. If the device doesn't initialize, either because it requires a firmware or because there's an error during init_drxk, returns -ENODEV, to indicate such error, on all DVB callbacks. Signed-off-by: -
Mauro Carvalho Chehab authored
Don't allow other devices at the same I2C bus to use it during firmware load, in order to prevent using the device while it is not on a sane state. Signed-off-by: -
Mauro Carvalho Chehab authored
As it will be using the unlocked version of i2c_transfer during firmware loads, make sure that the priv state routine will be used on all I2C calls, in preparation for the next patch that will implement an exclusive lock mode to be used during firmware load, at drxk_init. Signed-off-by: -
Mauro Carvalho Chehab authored
The firmware blob may not be available when the driver probes. Instead of blocking the whole kernel use request_firmware_nowait() and continue without firmware. This shouldn't be that bad on drx-k devices, as they all seem to have an internal firmware. So, only the firmware update will take a little longer to happen. Signed-off-by: -
Jean Delvare authored
Some drivers (in particular for TV cards) need exclusive access to their I2C buses for specific operations. Export an unlocked flavor of i2c_transfer to give them full control. The unlocked flavor has the following limitations: * Obviously, caller must hold the i2c adapter lock. * No debug messages are logged. We don't want to log messages while holding a rt_mutex. * No check is done on the existence of adap->algo->master_xfer. It is thus the caller's responsibility to ensure that the function is OK to call. Signed-off-by:
Jean Delvare <khali@linux-fr.org> Signed-off-by:
-
- 27 Jun, 2012 1 commit
-
-
Mauro Carvalho Chehab authored
* v4l_for_linus: (44 commits) [media] smia: Fix compile failures [media] Fix VIDIOC_DQEVENT docbook entry [media] s5p-fimc: Fix control creation function [media] s5p-mfc: Fix checkpatch error in s5p_mfc_shm.h file [media] s5p-mfc: Fix setting controls [media] v4l/s5p-mfc: added image size align in VIDIOC_TRY_FMT [media] v4l/s5p-mfc: corrected encoder v4l control definitions [media] v4l: mem2mem_testdev: Fix race conditions in driver [media] s5p-mfc: Bug fix of timestamp/timecode copy mechanism [media] cxd2820r: Fix an incorrect modulation type bitmask [media] em28xx: Show a warning if the board does not support remote controls [media] em28xx: Add remote control support for Terratec's Cinergy HTC Stick HD [media] USB: Staging: media: lirc: initialize spinlocks before usage [media] Revert "[media] media: mx2_camera: Fix mbus format handling" [media] bw-qcam: driver and pixfmt documentation fixes [media] cx88: fix firmware load on big-endian systems [media] cx18: support big-endian systems [media] ivtv: fix support for big-endian systems [media] tuner-core: return the frequency range of the correct tuner [media] v4l2-dev.c: fix g_parm regression in determine_valid_ioctls() ... Conflicts: Documentation/DocBook/media/v4l/vidioc-create-bufs.xml drivers/media/video/em28xx/em28xx-cards.c
-
- 25 Jun, 2012 10 commits
-
-
Benoît Thébaudeau authored
Cc: Ravi Kumar V <kumarrav@codeaurora.org> Signed-off-by:
Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Signed-off-by:
-
Benoît Thébaudeau authored
Make it possible for gpio-ir-recv users to choose a map name. Cc: Ravi Kumar V <kumarrav@codeaurora.org> Signed-off-by:
-
Benoît Thébaudeau authored
Add missing information so that udev can create an entry for gpio-ir-recv under /dev/input/by-path/ . Cc: Ravi Kumar V <kumarrav@codeaurora.org> Signed-off-by:
-
Ondrej Zary authored
Convert radio-sf16fmi to use generic LM7000 driver. Tested with SF16-FMI, SF16-FMP and SF16-FMD. Signed-off-by:
Ondrej Zary <linux@rainbow-software.org> Signed-off-by:
-
Ondrej Zary authored
Convert radio-aimslab to use generic LM7000 driver. Tested with Reveal RA300. Signed-off-by:
-
Ondrej Zary authored
Add very simple driver for Sanyo LM7000 AM/FM tuner chip. Only FM is supported as there is no known HW with AM implemented. This will be used by radio-aimslab and radio-sf16fmi. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
This reverts commit 4ecbb694. As requested by Hans Verkuil: > You accidentally merged the wrong first version of the lm7000 patch series. > > These are the correct second version patches: > > http://patchwork.linuxtv.org/patch/11689/ > http://patchwork.linuxtv.org/patch/11690/ > http://patchwork.linuxtv.org/patch/11691/ > > The second version is much simpler and doesn't require the creation of a whole > new driver. Requested-by:
Hans Verkuil <hverkuil@xs4all.nl> Cc: Ondrej Zary <linux@rainbow-software.org> Signed-off-by:
-
Mauro Carvalho Chehab authored
This reverts commit bece083a. As requested by Hans Verkuil: > You accidentally merged the wrong first version of the lm7000 patch series. > > These are the correct second version patches: > > http://patchwork.linuxtv.org/patch/11689/ > http://patchwork.linuxtv.org/patch/11690/ > http://patchwork.linuxtv.org/patch/11691/ > > The second version is much simpler and doesn't require the creation of a whole > new driver. Requested-by:
-
Mauro Carvalho Chehab authored
This reverts commit 1e70a6cf. As requested by Hans Verkuil: > You accidentally merged the wrong first version of the lm7000 patch series. > > These are the correct second version patches: > > http://patchwork.linuxtv.org/patch/11689/ > http://patchwork.linuxtv.org/patch/11690/ > http://patchwork.linuxtv.org/patch/11691/ > > The second version is much simpler and doesn't require the creation of a whole > new driver. Requested-by:
-
Daniel Glöckner authored
This is basically s/getmode/getrxsubchans/ and s/setmode/setaudmode/ with some whitespace adjustment in affected lines to please the eye. The rename is done to point out their relation to the rxsubchans and audmode fields of struct v4l2_tuner. I also corrected a commented out call to v4l_dbg in one of the lines. Signed-off-by:
Daniel Glöckner <daniel-gl@gmx.net> Acked-by:
-
- 21 Jun, 2012 23 commits
-
-
Peter Senna Tschudin authored
The switch/case was setting clock_setting that is not being used. Both switch/case and the variable definition were removed. Currently clock is being calculated by the formula: (state->fclk/1000000 - 8) Tested by compilation only. Signed-off-by:
Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by:
-
Peter Senna Tschudin authored
Tested by compilation only. Signed-off-by:
-
Peter Senna Tschudin authored
Tested by compilation only. Signed-off-by:
-
Peter Senna Tschudin authored
In function saa7164_api_i2c_read variable regval was set but not used. Tested by compilation only. Signed-off-by:
-
Peter Senna Tschudin authored
Tested by compilation only. Signed-off-by:
-
Peter Senna Tschudin authored
Saves 255 bytes of stack memory on cx231xx_usb_probe() by removing a char array. Tested by compilation only. Signed-off-by:
-
Peter Meerwald authored
Signed-off-by:
Peter Meerwald <p.meerwald@bct-electronic.com> Signed-off-by:
-
Paul Bolle authored
Commit 39c3d488 ("[media] cpia, stradis: remove deprecated V4L1 drivers") removed the last file including these five headers. Apparently it was just an oversight to keep them in the tree. They can safely be removed now. Signed-off-by:
Paul Bolle <pebolle@tiscali.nl> Signed-off-by:
-
Martin Blumenstingl authored
The windows driver used different values for the GPIOs and analog decoder configuration. The values from the windows driver are now used. It also seems that the windows driver has LNA always disabled. Thus we are doing the same (using the same flags as on windows). I (only) tested with DVB-T and it worked quite well. [mchehab@redhat.com: Fix merge conflicts and tested with DVB-C] Signed-off-by:
Martin Blumenstingl <martin.blumenstingl@googlemail.com> Tested-by:
-
Martin Blumenstingl authored
Signed-off-by:
-
Martin Blumenstingl authored
As of June 2012 it uses the same firmware as the Hauppauge WinTV HVR 930C. Signed-off-by:
-
Ondrej Zary authored
Convert radio-sf16fmi to use generic LM7000 driver. Tested with SF16-FMI, SF16-FMP and SF16-FMD. radio."); @@ -48,37 +50,40 @@ struct fmi bool mute; unsigned long curfreq; /* freq in kHz */ struct mutex lock; + struct lm7000 lm; }; static struct fmi fmi_card; static struct pnp_dev *dev; bool pnp_attached; -/* freq is in 1/16 kHz to internal number, hw precision is 50 kHz */ -/* It is only useful to give freq in interval of 800 (=0.05Mhz), - * other bits will be truncated, e.g 92.7400016 -> 92.7, but - * 92.7400017 -> 92.75 - */ -#define RSF16_ENCODE(x) ((x) / 800 + 214) #define RSF16_MINFREQ (87 * 16000) #define RSF16_MAXFREQ (108 * 16000) -static void outbits(int bits, unsigned int data, int io) +#define FMI_BIT_TUN_CE (1 << 0) +#define FMI_BIT_TUN_CLK (1 << 1) +#define FMI_BIT_TUN_DATA (1 << 2) +#define FMI_BIT_VOL_SW (1 << 3) +#define FMI_BIT_TUN_STRQ (1 << 4) + +void fmi_set_pins(struct lm7000 *lm, u8 pins) { - while (bits--) { - if (data & 1) { - outb(5, io); - udelay(6); - outb(7, io); - udelay(6); - } else { - outb(1, io); - udelay(6); - outb(3, io); - udelay(6); - } - data >>= 1; - } Signed-off-by: -
Ondrej Zary authored
Convert radio-aimslab to use generic LM7000 driver. Tested with Reveal RA300. Signed-off-by:
-
Ondrej Zary authored
Add very simple driver for Sanyo LM7000 AM/FM tuner chip. Only FM is supported as there is no known HW with AM implemented. This will be used by radio-aimslab and radio-sf16fmi. Signed-off-by:
-
Ezequiel García authored
Signed-off-by:
Ezequiel Garcia <elezegarcia@gmail.com> Signed-off-by:
-
Ezequiel García authored
There is a specific header sound/ac97_codec.h that defines these. All drivers should use it instead of rolling its own set of macros. Signed-off-by:
-
Ezequiel García authored
Signed-off-by:
-
Ezequiel García authored
Signed-off-by:
-
Hans Verkuil authored
And fix initial control setup. Signed-off-by:
-
Hans Verkuil authored
This driver allowed only one open filehandle. This is against the spec, so fix the driver by assigning proper ownership when streaming. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
