- 19 Mar, 2018 1 commit
-
-
Alexander Duyck authored
While doing some code review I noticed that we can get into a state where we exit with the "IN_CRITICAL_TASK" bit set while notifying the PF of flower filters. This patch is meant to address that plus tweak the ordering of the while loop waiting on it slightly so that we don't wait an extra period after we have failed for the last time. Signed-off-by:
Alexander Duyck <alexander.h.duyck@intel.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 18 Mar, 2018 31 commits
-
-
Stefano Brivio authored
Reported-by:
David Ahern <dsahern@gmail.com> Fixes: 1fad59ea ("selftests: pmtu: Add pmtu_vti6_link_change_mtu test") Signed-off-by:
Stefano Brivio <sbrivio@redhat.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Andrew Lunn says: ==================== Automatic PHY interrupts Now that the mv88e6xxx driver either installs in interrupt handler, or polls for interrupts, it is possible to always handle PHY interrupts, rather than have phylib perform the polling. This speeds up detection of link changes and reduces the load on the MDIO bus, which is beneficial for PTP. ==================== Signed-off-by: -
Andrew Lunn authored
When registering an MDIO bus, it is possible to pass an array of interrupts, one per address on the bus. phylib will then associate the interrupt to the PHY device, if no other interrupt is provided. Some of the global2 interrupts are PHY interrupts. Place them into the MDIO bus structure. Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Andrew Lunn authored
Add to the info structure the number of internal PHYs, if they generate interrupts. Some of the older generations of switches have internal PHYs, but no interrupt registers. In this case, set the count to zero. Signed-off-by:
-
Andrew Lunn authored
With the recent change to polling for interrupts, it is important that the number of global 1 interrupts is listed. Without it, the driver requests an interrupt domain for zero interrupts, which returns EINVAL, and the probe fails. Add two missing entries. Signed-off-by:
-
Florian Fainelli authored
We can hit the register lock not held assertion with the following path: [ 34.170631] mv88e6085 0.1:00: Switch registers lock not held! [ 34.176510] CPU: 0 PID: 950 Comm: ethtool Not tainted 4.16.0-rc4 #143 [ 34.182985] Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree) [ 34.189519] Backtrace: [ 34.192033] [<8010c4b4>] (dump_backtrace) from [<8010c788>] (show_stack+0x20/0x24) [ 34.199680] r6:9f5dc010 r5:00000011 r4:9f5dc010 r3:00000000 [ 34.205434] [<8010c768>] (show_stack) from [<80679d38>] (dump_stack+0x24/0x28) [ 34.212719] [<80679d14>] (dump_stack) from [<804844a8>] (mv88e6xxx_read+0x70/0x7c) [ 34.220376] [<80484438>] (mv88e6xxx_read) from [<804870dc>] (mv88e6xxx_port_get_cmode+0x34/0x4c) [ 34.229257] r5:a09cd128 r4:9ee31d07 [ 34.232880] [<804870a8>] (mv88e6xxx_port_get_cmode) from [<80487e6c>] (mv88e6352_port_has_serdes+0x24/0x64) [ 34.242690] r4:9f5dc010 [ 34.245309] [<80487e48>] (mv88e6352_port_has_serdes) from [<804880b8>] (mv88e6352_serdes_get_stats+0x28/0x12c) [ 34.255389] r4:00000001 [ 34.257973] [<80488090>] (mv88e6352_serdes_get_stats) from [<804811e8>] (mv88e6xxx_get_ethtool_stats+0xb0/0xc0) [ 34.268156] r10:00000000 r9:00000000 r8:00000000 r7:a09cd020 r6:00000001 r5:9f5dc01c [ 34.276052] r4:9f5dc010 [ 34.278631] [<80481138>] (mv88e6xxx_get_ethtool_stats) from [<8064f740>] (dsa_slave_get_ethtool_stats+0xbc/0xc4) mv88e6xxx_get_ethtool_stats() calls mv88e6xxx_get_stats() which calls both chip->info->ops->stats_get_stats(), which holds the register lock, and chip->info->ops->serdes_get_stats() which does not. Have chip->info->ops->serdes_get_stats() be running with the register lock held to avoid such assertions. Fixes: 436fe17d ("net: dsa: mv88e6xxx: Allow the SERDES interfaces to have statistics") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Reviewed-by:
-
Andrew Lunn authored
Handle polled interrupts correctly when loading the module. Signed-off-by:
-
David S. Miller authored
Stefano Brivio says: ==================== selftests: pmtu: Add further vti/vti6 MTU and PMTU tests Patches 5/10 to 10/10 add tests to verify default MTU assignment for vti4 and vti6 interfaces, to check that MTU values set on new link and link changes are properly taken and validated, and to verify PMTU exceptions on vti4 interfaces. Patch 1/10 reverses function return codes as suggested by David Ahern. Patch 2/10 fixes the helper to fetch exceptions MTU to run in the passed namespace. Patches 3/10 and 4/10 are preparation work to make it easier to introduce those tests. v2: Reverse return codes, and make output prettier in 4/9 by using padded printf, test descriptions and buffered error strings. Remove accidental output to /dev/kmsg from 10/10 (was 9/9). ==================== Signed-off-by: -
Stefano Brivio authored
This test checks that MTU configured from userspace is used on link creation and changes, and that when it's not passed from userspace, it's calculated properly from the MTU of the lower layer. Signed-off-by:
-
Stefano Brivio authored
Same as pmtu_vti4_link_add_mtu test, but for IPv6. Signed-off-by:
-
Stefano Brivio authored
This test checks that MTU given on vti link creation is actually configured, and that tunnel is not created with an invalid MTU value. Signed-off-by:
-
Stefano Brivio authored
This test checks that PMTU exceptions are created only when needed on IPv4 routes with vti and xfrm, and their PMTU value is checked as well. We can't adopt the same approach as test_pmtu_vti6_exception() here, because on IPv4 administrative MTU changes won't be reflected directly on PMTU. Signed-off-by:
-
Stefano Brivio authored
Same as pmtu_vti4_default_mtu, but on IPv6 with vti6. Signed-off-by:
-
Stefano Brivio authored
This test checks that the MTU assigned by default to a vti (IPv4) interface created on top of veth is simply veth's MTU minus the length of the encapsulated IPv4 header. Signed-off-by:
-
Stefano Brivio authored
Introduce list of tests and their descriptions, and loop on it in main body. Tests will now just take care of calling setup with a list of "units" they need, and return 0 on success, 1 on failure, 2 if the test had to be skipped. Main script body will take care of displaying results and cleaning up after every test. Introduce guard variable so that we don't clean up twice in case of interrupts or unexpected failures. The pmtu_vti6_exception test can now run its third step even if the previous one failed, as we can return values from it. Also introduce support to display test descriptions, and display aligned OK/FAIL/SKIP test outcomes. Buffer error strings so that in case of failure we can display them right under the outcome for each test. Signed-off-by:
-
Stefano Brivio authored
...so that it can be used for any iproute command output. Signed-off-by:
-
Stefano Brivio authored
In 7af137b72131 ("selftests: net: Introduce first PMTU test") I accidentally assumed route_get_* helpers would run from a single namespace. Make them a bit more generic, by passing the namespace command prefix as a parameter instead. Fixes: 7af137b72131 ("selftests: net: Introduce first PMTU test") Signed-off-by: -
Stefano Brivio authored
David suggests it's more intuitive to return non-zero on failures, and zero on success. No need to introduce tail 'return 0' in functions, they will return the exit code of the last command anyway. Suggested-by:
-
David S. Miller authored
Thomas Falcon says: ==================== ibmvnic: Update TX pool and TX routines This patch restructures the TX pool data structure and provides a separate TX pool array for TSO transmissions. This is already used in some way due to our unique DMA situation, namely that we cannot use single DMA mappings for packet data. Previously, both buffer arrays used the same pool entry. This restructuring allows for some additional cleanup in the driver code, especially in some places in the device transmit routine. In addition, it allows us to more easily track the consumer and producer indexes of a particular pool. This has been further improved by better tracking of in-use buffers to prevent possible data corruption in case an invalid buffer entry is used. v5: Fix bisectability mistake in the first patch. Removed TSO-specific data in a later patch when it is no longer used. v4: Fix error in 7th patch that causes an oops by using the older fixed value for number of buffers instead of the respective field in the tx pool data structure v3: Forgot to update TX pool cleaning function to handle new data structures. Included 7th patch for that. v2: Fix typo in 3/6 commit subject line ==================== Signed-off-by: -
Thomas Falcon authored
Finally, remove the TSO-specific fields in the TX pool strcutures. These are no longer needed with the introduction of separate buffer pools for TSO transmissions. Signed-off-by:
Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by:
-
Thomas Falcon authored
Update routine that cleans up any outstanding transmits that have not received completions when the device needs to close. Introduces a helper function that cleans one TX pool to make code more readable. Signed-off-by:
-
Thomas Falcon authored
Improve TX pool buffer accounting to prevent the producer index from overruning the consumer. First, set the next free index to an invalid value if it is in use. If next buffer to be consumed is in use, drop the packet. Finally, if the transmit fails for some other reason, roll back the consumer index and set the free map entry to its original value. This should also be done if the DMA map fails. Signed-off-by:
-
Thomas Falcon authored
Update TX and TX completion routines to account for TX pool restructuring. TX routine first chooses the pool depending on whether a packet is GSO or not, then uses it accordingly. For the completion routine to know which pool it needs to use, set the most significant bit of the correlator index to one if the packet uses the TSO pool. On completion, unset the bit and use the correlator index to release the buffer pool entry. Signed-off-by:
-
Thomas Falcon authored
Introduce function that initializes one TX pool. Use that to create each pool entry in both the standard TX pool and TSO pool arrays. Signed-off-by:
-
Thomas Falcon authored
Introduce function that frees one TX pool. Use that to release each pool in both the standard TX pool and TSO pool arrays. Signed-off-by:
-
Thomas Falcon authored
Update TX pool reset routine to accommodate new TSO pool array. Introduce a function that resets one TX pool, and use that function to initialize each pool in both pool arrays. Signed-off-by:
-
Thomas Falcon authored
Remove some unused fields in the structure and include values describing the individual buffer size and number of buffers in a TX pool. This allows us to use these fields for TX pool buffer accounting as opposed to using hard coded values. Include a new pool array for TSO transmissions. Signed-off-by:
-
Al Viro authored
use proc_remove_subtree() for subtree removal, both on setup failure halfway through and on teardown. No need to make simple things complex... Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
David S. Miller authored
Stephen Hemminger says: ==================== hv_netvsc: minor enhancements A couple of small things for net-next ==================== Signed-off-by: -
Stephen Hemminger authored
This adds tracepoints to the driver which has proved useful in debugging startup and shutdown race conditions. Signed-off-by:
Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by:
-
Stephen Hemminger authored
The caller has a valid pointer, pass it to rndis_filter_halt_device and avoid any possible RCU races here. Signed-off-by:
-
- 17 Mar, 2018 8 commits
-
-
Grygorii Strashko authored
In VLAN_AWARE mode CPSW can insert VLAN header encapsulation word on Host port 0 egress (RX) before the packet data if RX_VLAN_ENCAP bit is set in CPSW_CONTROL register. VLAN header encapsulation word has following format: HDR_PKT_Priority bits 29-31 - Header Packet VLAN prio (Highest prio: 7) HDR_PKT_CFI bits 28 - Header Packet VLAN CFI bit. HDR_PKT_Vid bits 27-16 - Header Packet VLAN ID PKT_Type bits 8-9 - Packet Type. Indicates whether the packet is VLAN-tagged, priority-tagged, or non-tagged. 00: VLAN-tagged packet 01: Reserved 10: Priority-tagged packet 11: Non-tagged packet This feature can be used to implement TX VLAN offload in case of VLAN-tagged packets and to insert VLAN tag in case Non-tagged packet was received on port with PVID set. As per documentation, CPSW never modifies packet data on Host egress (RX) and as result, without this feature enabled, Host port will not be able to receive properly packets which entered switch non-tagged through external Port with PVID set (when non-tagged packet forwarded from external Port with PVID set to another external Port - packet will be VLAN tagged properly). Implementation details: - on RX driver will check CPDMA status bit RX_VLAN_ENCAP BIT(19) in CPPI descriptor to identify when VLAN header encapsulation word is present. - PKT_Type = 0x01 or 0x02 then ignore VLAN header encapsulation word and pass packet as is; - if HDR_PKT_Vid = 0 then ignore VLAN header encapsulation word and pass packet as is; - In dual mac mode traffic is separated between ports using default port vlans, which are not be visible to Host and so should not be reported. Hence, check for default port vlans in dual mac mode and ignore VLAN header encapsulation word; - otherwise fill SKB with VLAN info using __vlan_hwaccel_put_tag(); - PKT_Type = 0x00 (VLAN-tagged) then strip out VLAN header from SKB. Signed-off-by:Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by:
-
Arjun Vynipadath authored
Setting sge_uld_rxq_info to NULL in free_queues_uld(). We are referencing sge_uld_rxq_info in cxgb_up(). This will fix a panic when interface is brought up after a ULDq creation failure. Fixes: 94cdb8bb (cxgb4: Add support for dynamic allocation of resources for ULD) Signed-off-by:
Arjun Vynipadath <arjun@chelsio.com> Signed-off-by:
Casey Leedom <leedom@chelsio.com> Signed-off-by:
Ganesh Goudhar <ganeshgr@chelsio.com> Signed-off-by:
-
Sowmini Varadhan authored
rds_tcp_connection allocation/free management has the potential to be called from __rds_conn_create after IRQs have been disabled, so spin_[un]lock_bh cannot be used with rds_tcp_conn_lock. Bottom-halves that need to synchronize for critical sections protected by rds_tcp_conn_lock should instead use rds_destroy_pending() correctly. Reported-by: syzbot+c68e51bb5e699d3f8d91@syzkaller.appspotmail.com Fixes: ebeeb1ad ("rds: tcp: use rds_destroy_pending() to synchronize netns/module teardown and rds connection/workq management") Signed-off-by:
Sowmini Varadhan <sowmini.varadhan@oracle.com> Acked-by:
Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by:
-
David S. Miller authored
Jon Maloy says: ==================== tipc: obsolete zone concept Functionality related to the 'zone' concept was never implemented in TIPC. In this series we eliminate the remaining traces of it in the code, and can hence take a first step in reducing the footprint and complexity of the binding table. ==================== Signed-off-by: -
Jon Maloy authored
We rename some lists and fields in struct publication both to make the naming more consistent and to better reflect their roles. We also update the descriptions of those lists. node_list -> local_publ cluster_list -> all_publ pport_list -> binding_sock ref -> port There are no functional changes in this commit. Acked-by:
Ying Xue <ying.xue@windriver.com> Signed-off-by:
Jon Maloy <jon.maloy@ericsson.com> Signed-off-by:
-
Jon Maloy authored
The size of struct publication can be reduced further. Membership in lists 'nodesub_list' and 'local_list' is mutually exlusive, in that remote publications use the former and local publications the latter. We replace the two lists with one single, named 'binding_node' which reflects what it really is. Acked-by:
-
Jon Maloy authored
As a further consequence of the previous commits, we can also remove the member 'zone_list 'in struct name_info and struct publication. Instead, we now let the member cluster_list take over the role a container of all publications of a given <type,lower, upper>. We also remove the counters for the size of those lists, since they don't serve any purpose. Acked-by:
-
Jon Maloy authored
As a consequence of the previous commit we nan now eliminate zone scope related lists in the name table. We start with name_table::publ_list[3], which can now be replaced with two lists, one for node scope publications and one for cluster scope publications. Acked-by:
-
