Add device id for Harman FirmwareHubEmulator to make the device
auto-detectable by the driver.
Signed-off-by: Clemens Werther <clemens.werther@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add device id for ELDAT Easywave RX09 tranceiver.
Reported-by: Jan Jansen <nattelip@hotmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds a device ID for the RT Systems cable used to
program Yaesu VX-8R/VX-8DR handheld radios. It uses the main
FTDI VID instead of the common RT Systems VID.
Signed-off-by: Major Hayden <major@mhtx.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The phys has already been initialized when add primary hcd,
including usb2 phys and usb3 phys also if exist, so needn't
re-parse "phys" property again.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The AB8540 was an evolved version of the AB8500, but it was never
mass produced or put into products, only reference designs exist.
The upstream support was never completed and it is unlikely that
this will happen so drop the support for now to simplify
maintenance of the AB8500.

Cc: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The AXP288 BC1.2 charger detection / extcon code may seem like a strange
place to add code to control the USB role-switch on devices with an AXP288,
but there are 2 reasons to do this inside the axp288 extcon code:

1) On many devices the USB role is controlled by ACPI AML code, but the AML
   code only switches between the host and none roles, because of Windows
   not really using device mode. To make device mode work we need to toggle
   between the none/device roles based on Vbus presence, and the axp288
   extcon gets interrupts on Vbus insertion / removal.

2) In order for our BC1.2 charger detection to work properly the role
   mux must be properly set to device mode before we do the detection.

Also note the Kconfig help-text / obsolete depends on USB_PHY which are
remnants from older never upstreamed code also controlling the mux from
the axp288 extcon code.

This commit also adds code to get notifications from the INT3496 extcon
device, which is used on some devices to notify the kernel about id-pin
changes instead of them being handled through AML code.

This fixes:
-Device mode not working on most CHT devices with an AXP288
-Host mode not working on devices with an INT3496 ACPI device
-Charger-type misdetection (always SDP) on devices with an INT3496 when the
 USB role (always) gets initialized as host
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We need to add device-connections for the Type-C mux/switch and usb-role
code to be able to find the PI3USB30532 Type-C cross-switch and the
device/host role-switch integrated in the CHT SoC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add a driver for the Pericom PI3USB30532 Type-C cross switch /
mux chip found on some devices with a Type-C port.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Various Intel SoCs (Cherry Trail, Broxton and others) have an internal USB
role switch for swiching the OTG USB data lines between the xHCI host
controller and the dwc3 gadget controller.

Note on some Cherry Trail systems there is ACPI/AML code listening to
edge interrupts on the id-pin (through an _AIE ACPI method) and switching
the role between ROLE_HOST and ROLE_NONE based on the id-pin. Note it does
not set the role to ROLE_DEVICE, because device-mode is usually not used
under Windows.

The presence of AML code which modifies the cfg0 reg (on some systems)
means that our read/write/modify of cfg0 may race with the AML code
doing the same to avoid this we take the global ACPI lock while doing
the read/write/modify.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The xHCI controller on various Intel SoCs has an extended cap mmio-range
which contains registers to control the muxing to the xHCI (host mode)
or the dwc3 (device mode) and vbus-detection for the otg usb-phy.

Having a role-sw driver included in the xHCI code (under drivers/usb/host)
is not desirable. So this commit adds a simple handler for this extended
capability, which creates a platform device with the caps mmio region as
resource, this allows us to write a separate platform role-sw driver for
the role-switch.

Note this commit adds a call to the new xhci_ext_cap_init() function
to xhci_pci_probe(), it is added here because xhci_ext_cap_init() must
be called only once. If in the future we also want to handle ext-caps
on non pci xHCI HCDs from xhci_ext_cap_init() a call to it should also
be added to other bus probe paths.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Modify xhci_find_next_ext_cap(base, offset, id) to return the next
capability offset if 0 is passed for id. Otherwise it will behave as
previously and return the offset of the next capability with matching id

capability id 0 is not used by xHCI (reserved)

This is useful when we want to loop through all capabilities.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove the unused (not implemented anywhere) tcpc_mux_dev abstraction
and replace it with calling the new typec_set_orientation,
usb_role_switch_set and typec_set_mode functions.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Setting the mux to MUX_NONE and the switch to USB_SWITCH_DISCONNECT when
the data-role is device is not correct. Plenty of devices support
operating as USB device through a (separate) USB device controller.

We really need 2 different versions of USB_SWITCH_CONNECT,
USB_SWITCH_CONNECT_HOST and USB_SWITCH_DEVICE. Rather then modifying the
tcpc_usb_switch enum for this, simply remove it and switch to the
usb_role enum which provides exactly this, this will save use needing to
convert betweent the 2 enums when calling an usb-role-switch driver later.

Besides switching to the usb_role type, this commit also actually sets the
mux to TYPEC_MUX_USB and the switch to USB_ROLE_DEVICE instead of setting
both to none when the data-role is device.

This commit also makes tcpm_reset_port() call tcpm_mux_set(port,
TYPEC_MUX_NONE, USB_ROLE_NONE) so that the mux and switch
do _not_ stay in their last mode after a detach.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB Type-C specification v1.2 separated the power and data
roles more clearly. Dual-Role-Data term was introduced, and
the meaning of DRP was changed from "Dual-Role-Port" to
"Dual-Role-Power".

In order to allow the port drivers to describe the
capabilities of the ports more clearly according to the
newest specifications, introducing separate definitions for
the data roles.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB role switch is a device that can be used to choose the
data role for USB connector. With dual-role capable USB
controllers, the controller itself will be the switch, but
on some platforms the USB host and device controllers are
separate IPs and there is a mux between them and the
connector. On those platforms the mux driver will need to
register the switch.

With USB Type-C connectors, the host-to-device relationship
is negotiated over the Configuration Channel (CC). That
means the USB Type-C drivers need to be in control of the
role switch. The class provides a simple API for the USB
Type-C drivers for the control.

For other types of USB connectors (mainly microAB) the class
provides user space control via sysfs attribute file that
can be used to request role swapping from the switch.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB Type-C connectors consist of various muxes and switches
that route the pins on the connector to the right locations.
The USB Type-C drivers need to be able to control the muxes,
as they are the ones that know things like the cable plug
orientation, and the current mode that was negotiated with
the partner.

This introduces a small API for registering and controlling
cable plug orientation switches, and separate small API for
registering and controlling pin multiplexer/demultiplexer
switches that are needed with Accessory/Alternate Modes.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Several frameworks - clk, gpio, phy, pmw, etc. - maintain
lookup tables for describing connections and provide custom
API for handling them. This introduces a single generic
lookup table and API for the connections.

The motivation for this commit is centralizing the
connection lookup, but the goal is to ultimately extract the
connection descriptions also from firmware by using the
fwnode_graph_* functions and other mechanisms that are
available.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usbipd includes exported devices in response to exportable device list.
Exclude exported devices from exportable device list to avoid:

- import requests for devices that are exported only to fail the request.
- revealing devices that are imported by a client to another client.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For some userspace applications information on the number of
over-current conditions at specific USB hub ports is relevant.

In our case we have a series of USB hardware (using the cp210x driver)
which communicates using a proprietary protocol. These devices sometimes
trigger an over-current situation on some hubs. In case of such an
over-current situation the USB devices offer an interface for reducing
the max used power. As these conditions are quite rare and imply
performance reductions of the device we don't want to reduce the max
power always.

Therefore give user-space applications the possibility to react
adequately by introducing an over_current_counter in the usb port struct
which is exported via sysfs.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Reporting two more VID/PID pairs that work with this driver, having used
an informational webpage <http://reboots.g-cipher.net/lcd/> as a buying
guide now. The page listed additional working VID/PID pairs but did not
include these two. None were upstreamed. Also taking this opportunity to
sort the pairs numerically.

Of the two such cables now in my possession, one is white, bearing the
In-System Design ISD-103 label on one side, sold as an Epson CAEUL0002
"USB to Parallel Smart Cable For Apple Macintosh Computers" (04b8:0002),
and the other is black, bearing the In-System Design ISD-101 label on one
side, sold as an early Belkin F5U002 (05ab:0002).
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Trying quirks in usbcore needs to rebuild the driver or the entire
kernel if it's builtin. It can save a lot of time if usbcore has similar
ability like "usbhid.quirks=" and "usb-storage.quirks=".

Rename the original quirk detection function to "static" as we introduce
this new "dynamic" function.

Now users can use "usbcore.quirks=" as short term workaround before the
next kernel release. Also, the quirk parameter can XOR the builtin
quirks for debugging purpose.

This is inspired by usbhid and usb-storage.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Update to show Minas Harutyunyan as the new maintainer for dwc2.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The maximum bytes per interval for USB SuperSpeed Plus can be set by
isoc endpoint companion descriptor when it is above 48K. If the
descriptor is provided, then use its value.

USB 3.1 spec 9.6.8
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'phy-for-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next

Kishon writes:

phy: for 4.17

 *) Add USB PHY driver for MDM6600 on Droid
 *) Add USB PHY driver for STM32 USB PHY Controller
 *) Add inno-usb2-phy driver for hi3798cv200 SoC
 *) Add combo phy driver (SATA/USB/PCIE) for HiSilicon STB SoCs
 *) Add USB3 PHY driver for Meson GXL and GXM
 *) Add support for R8A77965 Gen3 USB 2.0 PHY in phy-rcar-gen3-usb2 driver
 *) Add support for qualcomm QUSB2 V2 and QMP V3 USB3 PHY in phy-qcom-qusb2
    and phy-qcom-qmp PHY driver respectively
 *) Add support for runtime PM in phy-qcom-qusb2 and phy-qcom-qmp PHY drivers
 *) Add support for Allwinner R40 USB PHY in sun4i-usb PHY driver
 *) Add support in rockchip-typec PHY driver to make extcon optional and
    fallback to working in host mode if extcon is missing
 *) Add support in rockchip-typec PHY driver to mux PHYs connected to DP
 *) Add support to configure slew rate parameters in phy-mtk-tphy PHY driver
 *) Add workaround for missing Vbus det interrupts on Allwinner A23/A33
 *) Add USB speed related PHY modes in phy core
 *) Fix PHY 'structure' documentation
 *) Force rockchip-typec PHY to USB2 if DP-only mode is used
 *) Fix phy-qcom-qusb2 and phy-qcom-qmp PHY drivers to follow PHY reset and
    initialization sequence as per hardware programming manual
 *) Fix Marvell BG2CD SoC USB failure in phy-berlin-usb driver
 *) Minor fixes in lpc18xx-usb-otg, xusb-tegra210 and phy-rockchip-emmc PHY
    drivers
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

We want the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull x86/pti updates from Thomas Gleixner:
 "Another set of melted spectrum updates:

   - Iron out the last late microcode loading issues by actually
     checking whether new microcode is present and preventing the CPU
     synchronization to run into a timeout induced hang.

   - Remove Skylake C2 from the microcode blacklist according to the
     latest Intel documentation

   - Fix the VM86 POPF emulation which traps if VIP is set, but VIF is
     not. Enhance the selftests to catch that kind of issue

   - Annotate indirect calls/jumps for objtool on 32bit. This is not a
     functional issue, but for consistency sake its the right thing to
     do.

   - Fix a jump label build warning observed on SPARC64 which uses 32bit
     storage for the code location which is casted to 64 bit pointer w/o
     extending it to 64bit first.

   - Add two new cpufeature bits. Not really an urgent issue, but
     provides them for both x86 and x86/kvm work. No impact on the
     current kernel"

* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/microcode: Fix CPU synchronization routine
  x86/microcode: Attempt late loading only when new microcode is present
  x86/speculation: Remove Skylake C2 from Speculation Control microcode blacklist
  jump_label: Fix sparc64 warning
  x86/speculation, objtool: Annotate indirect calls/jumps for objtool on 32-bit kernels
  x86/vm86/32: Fix POPF emulation
  selftests/x86/entry_from_vm86: Add test cases for POPF
  selftests/x86/entry_from_vm86: Exit with 1 if we fail
  x86/cpufeatures: Add Intel PCONFIG cpufeature
  x86/cpufeatures: Add Intel Total Memory Encryption cpufeature

Pull x86 fix from Thomas Gleixner:
 "A single fix for vmalloc_fault() which uses p*d_huge() unconditionally
  whether CONFIG_HUGETLBFS is set or not. In case of CONFIG_HUGETLBFS=n
  this results in a crash as p*d_huge() returns 0 in that case"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm: Fix vmalloc_fault to use pXd_large

Pull irq fixes from Thomas Gleixner:
 "Three fixes for irq chip drivers:

   - Make sure the allocations in the GIC-V3 ITS driver are large enough
     to accomodate the interrupt space

   - Fix a misplaced __iomem annotation which causes a splat of 26
     sparse warnings

   - Remove an unused function in the IMX GPCV2 driver which causes
     build warnings"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/irq-imx-gpcv2: Remove unused function
  irqchip/gic-v3-its: Ensure nr_ites >= nr_lpis
  irqchip/gic-v3-its: Fix misplaced __iomem annotations

Pull EFI fix from Thomas Gleixner:
 "A single fix to prevent partially initialized pointers in mixed mode
  (64bit kernel on 32bit UEFI)"

* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  efi/libstub/tpm: Initialize pointer variables to zero for mixed mode

Pull KVM fixes from Paolo Bonzini:
 "PPC:
   - fix bug leading to lost IPIs and smp_call_function_many() lockups
     on POWER9

  ARM:
   - locking fix
   - reset fix
   - GICv2 multi-source SGI injection fix
   - GICv2-on-v3 MMIO synchronization fix
   - make the console less verbose.

  x86:
   - fix device passthrough on AMD SME"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86: Fix device passthrough when SME is active
  kvm: arm/arm64: vgic-v3: Tighten synchronization for guests using v2 on v3
  KVM: arm/arm64: vgic: Don't populate multiple LRs with the same vintid
  KVM: arm/arm64: Reduce verbosity of KVM init log
  KVM: arm/arm64: Reset mapped IRQs on VM reset
  KVM: arm/arm64: Avoid vcpu_load for other vcpu ioctls than KVM_RUN
  KVM: arm/arm64: vgic: Add missing irq_lock to vgic_mmio_read_pending
  KVM: PPC: Book3S HV: Fix trap number return from __kvmppc_vcore_entry

Just when I had decided that flush_cache_range() was always called with
a valid context, Helge reported two cases where the
"BUG_ON(!vma->vm_mm->context);" was hit on the phantom buildd:

 kernel BUG at /mnt/sdb6/linux/linux-4.15.4/arch/parisc/kernel/cache.c:587!
 CPU: 1 PID: 3254 Comm: kworker/1:2 Tainted: G D 4.15.0-1-parisc64-smp #1 Debian 4.15.4-1+b1
 Workqueue: events free_ioctx
  IAOQ[0]: flush_cache_range+0x164/0x168
  IAOQ[1]: flush_cache_page+0x0/0x1c8
  RP(r2): unmap_page_range+0xae8/0xb88
 Backtrace:
  [<00000000404a6980>] unmap_page_range+0xae8/0xb88
  [<00000000404a6ae0>] unmap_single_vma+0xc0/0x188
  [<00000000404a6cdc>] zap_page_range_single+0x134/0x1f8
  [<00000000404a702c>] unmap_mapping_range+0x1cc/0x208
  [<0000000040461518>] truncate_pagecache+0x98/0x108
  [<0000000040461624>] truncate_setsize+0x9c/0xb8
  [<00000000405d7f30>] put_aio_ring_file+0x80/0x100
  [<00000000405d803c>] aio_free_ring+0x8c/0x290
  [<00000000405d82c0>] free_ioctx+0x80/0x180
  [<0000000040284e6c>] process_one_work+0x21c/0x668
  [<00000000402854c4>] worker_thread+0x20c/0x778
  [<0000000040291d44>] kthread+0x2d4/0x2e0
  [<0000000040204020>] end_fault_vector+0x20/0xc0

This indicates that we need to handle the no context case in
flush_cache_range() as we do in flush_cache_mm().

In thinking about this, I realized that we don't need to flush the TLB
when there is no context.  So, I added context checks to the large flush
cases in flush_cache_mm() and flush_cache_range().  The large flush case
occurs frequently in flush_cache_mm() and the change should improve fork
performance.

The v2 version of this change removes the BUG_ON from flush_cache_page()
by skipping the TLB flush when there is no context.  I also added code
to flush the TLB in flush_cache_mm() and flush_cache_range() when we
have a context that's not current.  Now all three routines handle TLB
flushes in a similar manner.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # 4.9+
Signed-off-by: Helge Deller <deller@gmx.de>

Pull btrfs fixes from David Sterba:
 "There's an important revert in this pull request that needs to go to
  stable as it causes a corruption on big endian machines.

  The other fix is for FIEMAP incorrectly reporting shared extents
  before a sync and one fix for a crash in raid56.

  So far we got only one report about the BE corruption, the stable
  kernels were out for like a week, so hopefully the scope of the damage
  is low"

* tag 'for-4.16-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  Revert "btrfs: use proper endianness accessors for super_copy"
  btrfs: add missing initialization in btrfs_check_shared
  btrfs: Fix NULL pointer exception in find_bio_stripe

Pull microblaze fixes from Michal Simek:

 - Use NO_BOOTMEM to fix boot issue

 - Fix opt lib endian dependencies

* tag 'microblaze-4.16-rc6' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: switch to NO_BOOTMEM
  microblaze: remove unused alloc_maybe_bootmem
  microblaze: Setup dependencies for ASM optimized lib functions

Emanuel reported an issue with a hang during microcode update because my
dumb idea to use one atomic synchronization variable for both rendezvous
- before and after update - was simply bollocks:

  microcode: microcode_reload_late: late_cpus: 4
  microcode: __reload_late: cpu 2 entered
  microcode: __reload_late: cpu 1 entered
  microcode: __reload_late: cpu 3 entered
  microcode: __reload_late: cpu 0 entered
  microcode: __reload_late: cpu 1 left
  microcode: Timeout while waiting for CPUs rendezvous, remaining: 1

CPU1 above would finish, leave and the others will still spin waiting for
it to join.

So do two synchronization atomics instead, which makes the code a lot more
straightforward.

Also, since the update is serialized and it also takes quite some time per
microcode engine, increase the exit timeout by the number of CPUs on the
system.

That's ok because the moment all CPUs are done, that timeout will be cut
short.

Furthermore, panic when some of the CPUs timeout when returning from a
microcode update: we can't allow a system with not all cores updated.

Also, as an optimization, do not do the exit sync if microcode wasn't
updated.
Reported-by: Emanuel Czirai <xftroxgpx@protonmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Emanuel Czirai <xftroxgpx@protonmail.com>
Tested-by: Ashok Raj <ashok.raj@intel.com>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lkml.kernel.org/r/20180314183615.17629-2-bp@alien8.de

Return UCODE_NEW from the scanning functions to denote that new microcode
was found and only then attempt the expensive synchronization dance.
Reported-by: Emanuel Czirai <xftroxgpx@protonmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Emanuel Czirai <xftroxgpx@protonmail.com>
Tested-by: Ashok Raj <ashok.raj@intel.com>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lkml.kernel.org/r/20180314183615.17629-1-bp@alien8.de

Pull drm fixes from Dave Airlie:
 "i915, amd and nouveau fixes.

  i915:
   - backlight fix for some panels
   - pm fix
   - fencing fix
   - some GVT fixes

  amdgpu:
   - backlight fix across suspend/resume
   - object destruction ordering issue fix
   - displayport fix

  nouveau:
   - two backlight fixes
   - fix for some lockups

  Pretty quiet week, seems like everyone was fixing backlights"

* tag 'drm-fixes-for-v4.16-rc6' of git://people.freedesktop.org/~airlied/linux:
  drm/nouveau/bl: fix backlight regression
  drm/nouveau/bl: Fix oops on driver unbind
  drm/nouveau/mmu: ALIGN_DOWN correct variable
  drm/i915/gvt: fix user copy warning by whitelist workload rb_tail field
  drm/i915/gvt: Correct the privilege shadow batch buffer address
  drm/amdgpu/dce: Don't turn off DP sink when disconnected
  drm/amdgpu: save/restore backlight level in legacy dce code
  drm/radeon: fix prime teardown order
  drm/amdgpu: fix prime teardown order
  drm/i915: Kick the rps worker when changing the boost frequency
  drm/i915: Only prune fences after wait-for-all
  drm/i915: Enable VBT based BL control for DP
  drm/i915/gvt: keep oa config in shadow ctx
  drm/i915/gvt: Add runtime_pm_get/put into gvt_switch_mmio

In preparation to enabling -Wvla, remove VLA and replace it
with dynamic memory allocation instead.

The use of stack Variable Length Arrays needs to be avoided, as they
can be a vector for stack exhaustion, which can be both a runtime bug
or a security flaw. Also, in general, as code evolves it is easy to
lose track of how big a VLA can get. Thus, we can end up having runtime
failures that are hard to debug.

Also, fixed as part of the directive to remove all VLAs from
the kernel: https://lkml.org/lkml/2018/3/7/621

Notice that in this particular case, an alternative to kzalloc is kcalloc,
in which case the code would look as follows instead:

iv = kcalloc(crypto_skcipher_ivsize(tfm_cbc), sizeof(*iv), GFP_KERNEL);

but if the data type of _iv_ never changes, or the type size is always one
byte, kzalloc is good enough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci driver displays the supported xHC USB revision in a message during
driver load:

"Host supports USB 3.1 Enhanced SuperSpeed"

Get the USB minor revision number from the xhci protocol capability.
This will show the correct supported revisions for new USB 3.2 and later
hosts

Don't rely on the SBRN (serial bus revision number) register, it's often
showing 0x30 (USB3.0) for hosts that support USB 3.1
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>