This patch updates mwifiex Copyright to 2014.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some SDIO controllers do not support MMC_PM_KEEP_POWER properly.
To test host sleep feature without putting the system into sleep
we need to simulate host sleep configuration & handshake between
driver and firmware using customized parameters.
This patch adds hscfg debugfs item, with which user could change
host sleep parameters for debugging.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Firmware dump feature is added for SDIO based chipsets
which can be used with the help of ethtool commands.

1) Trigger firmware dump operation:
ethtool --set-dump mlan0 0xff

When the operation is completed, udev event will be sent to
trigger external application.

2) Following udev rule can be used to get the data from ethtool:
DRIVER=="mwifiex_sdio", ACTION=="change", RUN+="/sbin/mwifiex_sdio_fw_dump.sh"

mwifiex_sdio_fw_dump.sh: #!/bin/bash
ethtool --set-dump mlan0 0
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/ITCM.log

ethtool --set-dump mlan0 1
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/DTCM.log

ethtool --set-dump mlan0 2
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/SQRAM.log

ethtool --set-dump mlan0 3
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/APU.log

ethtool --set-dump mlan0 4
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/CIU.log

ethtool --set-dump mlan0 5
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/ICU.log

ethtool --set-dump mlan0 6
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/MAC.log
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

As we can derive host pointer from adapter, maintaining
a global variable doesn't make sense.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Existing dedicated card_reset work queue is replaced with the
interface specific workqueue pointer provided by mwifiex module.
Also new work flag is added for card reset task.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Firmware dump feature is added for PCIe based chipsets which can
be used with the help of ethtool commands.

1) Trigger firmware dump operation:
ethtool --set-dump mlan0 0xff

When the operation is completed, udev event will be sent to
trigger external application.

2) Following udev rule can be used to get the data from ethtool:
DRIVER=="mwifiex_pcie", ACTION=="change", RUN+="/sbin/mwifiex_pcie_fw_dump.sh"

mwifiex_pcie_fw_dump.sh: #!/bin/bash
ethtool --set-dump mlan0 0
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/ITCM.log

ethtool --set-dump mlan0 1
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/DTCM.log

ethtool --set-dump mlan0 2
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/SQRAM.log

ethtool --set-dump mlan0 3
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/IRAM.log
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Driver is now responsible for veryfing if the
switch is possible.

Since this is inherently tricky driver may decide
to disconnect an interface later with
cfg80211_stop_iface().

This doesn't mean driver can accept everything. It
should do it's best to verify requests and reject
them as soon as possible.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Channel switch finalization is now 2-step. First
step is when driver calls chswitch_done(), the
other is when reservation is actually finalized
(which be defered for in-place reservation).

It is now safe to call ieee80211_chswitch_done()
more than once.

Also remove the ieee80211_vif_change_channel()
because it is no longer used.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Channel switch finalization is now 2-step. First
step is when driver calls csa_finish(), the other
is when reservation is actually finalized (which
can be deferred for in-place reservation).

It is now safe to call ieee80211_csa_finish() more
than once.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The ieee80211_check_combinations() computes
radar_detect accordingly depending on chanctx
reservation status.

This makes it possible to use the function for
channel_switch validation.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Multi-vif in-place reservations happen when
it is impossible to allocate more channel contexts
as indicated by interface combinations.

Such reservations are not finalized until all
assigned interfaces are ready.

This still doesn't handle all possible cases
(i.e. degradation of number of channels) properly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Split sched scan IEs to band specific and not band specific
blocks. Common IEs blocks may be sent to the FW once per command,
instead of per band.

This allows optimization of size of the command, which may be
required by some drivers (eg. iwlmvm with newer firmware version).

As this changes the mac80211 API, update all drivers to use the
new version correctly, even if they don't (yet) make use of the
split data.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Some drivers (such as iwlmvm) can handle multiple bands in a single
HW scan request. Add a HW flag to indicate that the driver support
this. To hold the required data, create a separate structure for
HW scan request that holds cfg scan request and data about
different parts of the scan IEs.

As this changes the mac80211 API, update all drivers using it to
use the correct new function type/argument.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If the device fails during a restart, mac80211 now handles the
situation better but we still have a little bit of cleanup to
do in the driver - add the required code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: ArikX Nemtsov <arik@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Since the new API allows multiple priorities, we need to
properly set the beacon's prorities in the TX cmd associated
to it.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Use extended beacon notification when supported by FW.
Set last beacon system time to AP or GO interface.
System time of last beacon can be used to avoid TBTT overlapping
between two interfaces, CSA and other uses.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Introduce new station flag STA_FLG_DISABLE_TX, which is modified with ADD_STA
command. This flag, when set, disables tx to the STA.
Provide an API (iwl_mvm_sta_modify_disable_tx) to modify this flag, which
should be used in channel switch and immediate quiet flows.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The beacon filtering configuration in d0i3 currently uses
the max value defined as 1024. However, with beacon interval
of 100ms we end up with too-frequent wakeups.

Instead, configure the escape timer to 0, asking the fw
to disable it altogether.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

If BT is active, we need to refrain from using the shared
antenna. This logic is done in the firmware when we use the
link quality tables. But for management frames, the rate is
written in the Tx command by the driver.
Hence the driver needs to make sure not use the shared
antenna when BT is active for any frames that don't use
the rate scale table such as management frames or multicast.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This really belongs to the constants file.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When the firmware enables TxTxCorunning, we can lift the
constaints on the rate control.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

We can Tx in MIMO rates when we are in TxTx Disallow mode
just like we can when we are in Tight mode.
Same if we are in 5Ghz regardless of the mode we are.
Change the code to allow MIMO in these cases.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This can be used for testing.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Just in case sizes change in the OTP without proper SW
updating, an additional check is inserted when reading OTP
sections to assure no overflows occur.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Some of the maximum values of the parsed external NVM file
in the B-step of the 8000 HW family were updated, so this
updates these values.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The format of the CSR_HW_REV register has changed in 8000
HW family. To keep backwards compatibility, we store the
value of this register as usual in trans->hw_rev, only we
store it in the old format in this variable.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Don't use nvm_hw pointer if it is NULL. Print an error
message if the MAC address isn't valid.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

iwldvm stalls are often blamed on power management.  Add an option
to force it all the way off.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This adds need_update and write_actual to rx_queue and need_update
and an HCMD indicator to tx_queue.

On my card, rx_queue now looks like:

read: 181
write: 180
write_actual: 176
need_update: 0
free_count: 40
closed_rb_num: 181

tx_queue now looks like:

hwq 00: read=29 write=30 use=1 stop=0 need_update=0
hwq 01: read=0 write=0 use=1 stop=0 need_update=0
hwq 02: read=128 write=128 use=1 stop=0 need_update=0
hwq 03: read=0 write=0 use=1 stop=0 need_update=0
hwq 04: read=94 write=94 use=1 stop=0 need_update=0 HCMD
hwq 05: read=0 write=0 use=0 stop=0 need_update=0
hwq 06: read=0 write=0 use=0 stop=0 need_update=0
hwq 07: read=0 write=0 use=0 stop=0 need_update=0
hwq 08: read=0 write=0 use=0 stop=0 need_update=0
hwq 09: read=0 write=0 use=0 stop=0 need_update=0
hwq 10: read=0 write=0 use=0 stop=0 need_update=0
hwq 11: read=0 write=0 use=0 stop=0 need_update=0
hwq 12: read=0 write=0 use=0 stop=0 need_update=0
hwq 13: read=0 write=0 use=0 stop=0 need_update=0
hwq 14: read=0 write=0 use=0 stop=0 need_update=0
hwq 15: read=0 write=0 use=0 stop=0 need_update=0
hwq 16: read=0 write=0 use=0 stop=0 need_update=0
hwq 17: read=0 write=0 use=0 stop=0 need_update=0
hwq 18: read=0 write=0 use=0 stop=0 need_update=0
hwq 19: read=0 write=0 use=0 stop=0 need_update=0

This may help with debugging queue stalls.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

I've never seen this happen, but it's useful to rule it out.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Fix NVM channel attributes. Add indoor-only and GO Concurrent
bits. Remove DFS channel bit which is overlapped with radar.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The nvm_file should be loaded by default for SDIO
procucts only. Change the configuration accordingly.
While at it, fix a typo in the device name.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This allows to use the firmware monitor. This capability
uses a lot of contiguous memory (up to 64MB), so make its
usage module parameter dependent.

The driver will try to allocate as much contiguous memory
as possible downgrading its requirements until the
allocation succeeds.

Dump this data into the fw-error dump file when an error
happens.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This is not related to mvm. Rename to iwl_fw_error_next_data.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This can be useful later for parsing since the parsing may
differ based on the device's family / bus.
Also add the human readable version of the firmware.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

MCS32 is currently not supported, so don't
declare support for it.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Use num of scan channels as advertised by fw TLV.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>