- 31 Jul, 2020 7 commits
-
-
Randy Dunlap authored
Drop doubled words "are" and "by" in comments. Change doubled "to to" to "to the". Signed-off-by:
Randy Dunlap <rdunlap@infradead.org> Cc: netdev@vger.kernel.org Cc: Kalle Valo <kvalo@codeaurora.org> Cc: linux-wireless@vger.kernel.org Cc: Johannes Berg <johannes@sipsolutions.net> Link: https://lore.kernel.org/r/20200715164325.9109-4-rdunlap@infradead.orgSigned-off-by:
Johannes Berg <johannes.berg@intel.com>
-
Randy Dunlap authored
Drop doubled word "by" in a comment. Change "operate in in" to "operate with in" as is used below. Signed-off-by:
-
Randy Dunlap authored
Drop doubled word "threshold" in a comment. Signed-off-by:
-
Randy Dunlap authored
Drop doubled words in several comments. Signed-off-by:
-
Julian Squires authored
nl80211 vendor netlink dumpit, like netlink_callback->dump, should signal successful completion by returning 0. Currently, that will just cause dumpit to be called again, possibly many times until an error occurs. Since skb->len is never going to be 0 by the time dumpit is called, the only way for dumpit to signal completion is by returning an error. If it returns a positive value, the current message is cancelled, but that positive value is returned and nl80211_vendor_cmd_dump gets called again. Fix that by passing a return value of 0 through. Signed-off-by:
Julian Squires <julian@cipht.net> Link: https://lore.kernel.org/r/20200720145033.401307-1-julian@cipht.net [reword commit message] Signed-off-by:
-
Colin Ian King authored
Currently rates_idx is being initialized with the value -1 and this value is never read so the initialization is redundant and can be removed. The next time the variable is used it is assigned a value that is returned a few statements later. Just return i - 1 and remove the need for rates_idx. Addresses-Coverity: ("Unused value") Signed-off-by:Colin Ian King <colin.king@canonical.com> Link: https://lore.kernel.org/r/20200722153830.959010-1-colin.king@canonical.comSigned-off-by:
-
Thomas Pedersen authored
Gives drivers the definitions needed to advertise support for S1G bands. Signed-off-by:
Thomas Pedersen <thomas@adapt-ip.com> Link: https://lore.kernel.org/r/20200602062247.23212-1-thomas@adapt-ip.com Link: https://lore.kernel.org/r/20200731055636.795173-1-thomas@adapt-ip.comSigned-off-by:
-
- 29 Jul, 2020 33 commits
-
-
Brian Vazquez authored
This patch fixes: commit b9aaec8f ("fib: use indirect call wrappers in the most common fib_rules_ops") which didn't consider the case when CONFIG_IPV6_MULTIPLE_TABLES is not set. Reported-by:
Stephen Rothwell <sfr@canb.auug.org.au> Fixes: b9aaec8f ("fib: use indirect call wrappers in the most common fib_rules_ops") Signed-off-by:
Brian Vazquez <brianvv@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller authored
Tony Nguyen says: ==================== 100GbE Intel Wired LAN Driver Updates 2020-07-29 This series contains updates to the ice driver only. Dave works around LFC settings not being preserved through link events. Fixes link issues with GLOBR reset and handling of multiple link events. Nick restores VF MSI-X after PCI reset. Kiran corrects the error code returned in ice_aq_sw_rules if the rule does not exist. Paul prevents overwriting of user set descriptors. Tarun adds masking before accessing rate limiting profile types and corrects queue bandwidth configuration. Victor modifies Tx queue scheduler distribution to spread more evenly across queue group nodes. Krzysztof sets need_wakeup flag for Tx AF_XDP. Brett allows VLANs in safe mode. Marcin cleans up VSIs on probe failure. Bruce reduces the scope of a variable. Ben removes a FW workaround. Tony fixes an unused parameter warning. ==================== Signed-off-by: -
Jisheng Zhang authored
mvneta has switched to phylink, so the comment should look like "We may have called phylink_speed_down before". Signed-off-by:
Jisheng Zhang <Jisheng.Zhang@synaptics.com> Reviewed-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
-
Tony Nguyen authored
Depending on PAGE_SIZE, the following unused parameter warning can be reported: drivers/net/ethernet/intel/ice/ice_txrx.c: In function ‘ice_rx_frame_truesize’: drivers/net/ethernet/intel/ice/ice_txrx.c:513:21: warning: unused parameter ‘size’ [-Wunused-parameter] unsigned int size) The 'size' variable is used only when PAGE_SIZE >= 8192. Add __maybe_unused to remove the warning. Signed-off-by:Tony Nguyen <anthony.l.nguyen@intel.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com>
-
Ben Shelton authored
For the FW logging info AQ command, we currently set the ICE_AQ_FLAG_RD in order to work around a FW issue. This issue has been fixed so remove the workaround. Signed-off-by:
Ben Shelton <benjamin.h.shelton@intel.com> Tested-by:
-
Bruce Allan authored
The scope of the macro local variable 'i' can be reduced. Do so to avoid static analysis tools from complaining. Signed-off-by:
Bruce Allan <bruce.w.allan@intel.com> Tested-by:
-
Marcin Szycik authored
As part of ice_setup_pf_sw() a PF VSI is setup; release the VSI in case of failure. Signed-off-by:
Marcin Szycik <marcin.szycik@intel.com> Tested-by:
-
Brett Creeley authored
Currently the PF VSI's context parameters are left in a bad state when going into safe mode. This is causing VLAN traffic to not pass. Fix this by configuring the PF VSI to allow all VLAN tagged traffic. Also, remove redundant comment explaining the safe mode flow in ice_probe(). Signed-off-by:
Brett Creeley <brett.creeley@intel.com> Tested-by:
-
Krzysztof Kazimierczak authored
This is a port of i40e commit 70563957 ("i40e: need_wakeup flag might not be set for Tx"). Quoting the original commit message: "The need_wakeup flag for Tx might not be set for AF_XDP sockets that are only used to send packets. This happens if there is at least one outstanding packet that has not been completed by the hardware and we get that corresponding completion (which will not generate an interrupt since interrupts are disabled in the napi poll loop) between the time we stopped processing the Tx completions and interrupts are enabled again. In this case, the need_wakeup flag will have been cleared at the end of the Tx completion processing as we believe we will get an interrupt from the outstanding completion at a later point in time. But if this completion interrupt occurs before interrupts are enable, we lose it and should at that point really have set the need_wakeup flag since there are no more outstanding completions that can generate an interrupt to continue the processing. When this happens, user space will see a Tx queue need_wakeup of 0 and skip issuing a syscall, which means will never get into the Tx processing again and we have a deadlock." As a result, packet processing stops. This patch introduces a fix for this issue, by always setting the need_wakeup flag at the end of an interrupt processing. This ensures that the deadlock will not happen. Signed-off-by:
Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com> Tested-by:
-
Victor Raj authored
Distribute the Tx queues evenly across all queue groups. This will help the queues to get more equal sharing among the queues when all are in use. In the previous algorithm, the next queue group node will be picked up only after the previous one filled with max children. For example: if VSI is configured with 9 queues, the first 8 queues will be assigned to queue group 1 and the 9th queue will be assigned to queue group 2. The 2 queue groups split the bandwidth between them equally (50:50). The first queue group node will share the 50% bandwidth with all of its children (8 queues). And the second queue group node will share the entire 50% bandwidth with its only children. The new algorithm will fix this issue. Signed-off-by:
Victor Raj <victor.raj@intel.com> Tested-by:
-
Tarun Singh authored
By default the queues are configured in legacy mode. The default BW settings for legacy/advanced modes are different. The existing code was using the advanced mode default value of 1 which was incorrect. This caused the unbalanced BW sharing among siblings. The recommended default value is applied. Signed-off-by:
Tarun Singh <tarun.k.singh@intel.com> Tested-by:
-
Tarun Singh authored
Mask bits before accessing the profile type field. Signed-off-by:
-
Paul M Stillwell Jr authored
If a user sets the value of the TX or RX descriptors to some non-default value using 'ethtool -G' then we need to not overwrite the values when we rebuild the VSI. The VSI rebuild could happen as a result of a user setting the number of queues via the 'ethtool -L' command. Fix this by checking to see if the value we have stored is non-zero and if it is then don't change the value. Signed-off-by:
Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com> Tested-by:
-
Kiran Patil authored
Return ICE_ERR_DOES_NOT_EXIST return code if admin command error code is ICE_AQ_RC_ENOENT (not exist). ice_aq_sw_rules is used when switch rule is getting added/deleted/updated. In case of delete/update switch rule, admin command can return ICE_AQ_RC_ENOENT error code if such rule does not exist, hence return ICE_ERR_DOES_NOT_EXIST error code from ice_aq_sw_rule, so that caller of this function can decide how to handle ICE_ERR_DOES_NOT_EXIST. Signed-off-by:
Kiran Patil <kiran.patil@intel.com> Tested-by:
-
Nick Nunley authored
During a PCI FLR the MSI-X Enable flag in the VF PCI MSI-X capability register will be cleared. This can lead to issues when a VF is assigned to a VM because in these cases the VF driver receives no indication of the PF PCI error/reset and additionally it is incapable of restoring the cleared flag in the hypervisor configuration space without fully reinitializing the driver interrupt functionality. Since the VF driver is unable to easily resolve this condition on its own, restore the VF MSI-X flag during the PF PCI reset handling. Signed-off-by:
Nick Nunley <nicholas.d.nunley@intel.com> Tested-by:
-
Dave Ertman authored
When the driver experiences a link event (especially link up) there can be multiple events generated. Some of these are link fault and still have a state of DOWN set. The problem happens when the link comes UP during the PF driver handling one of the LINK DOWN events. The status of the link is updated and is now seen as UP, so when the actual LINK UP event comes, the port information has already been updated to be seen as UP, even though none of the UP activities have been completed. After the link information has been updated in the link handler and evaluated for MEDIA PRESENT, if the state of the link has been changed to UP, treat the DOWN event as an UP event since the link is now UP. Signed-off-by:
Dave Ertman <david.m.ertman@intel.com> Tested-by:
-
Dave Ertman authored
After a GLOBR, the link was broken so that a link up situation was being seen as a link down. The problem was that the rebuild process was updating the port_info link status without doing any of the other things that need to be done when link changes. This was causing the port_info struct to have current "UP" information so that any further UP interrupts were skipped as redundant. The rebuild flow should *not* be updating the port_info struct link information, so eliminate this and leave it to the link event handling code. Signed-off-by:
-
Dave Ertman authored
There is a bug where the LFC settings are not being preserved through a link event. The registers in question are the ones that are touched (and restored) when a set_local_mib AQ command is performed. On a link-up event, make sure that a set_local_mib is being performed. Move the function ice_aq_set_lldp_mib() from the DCB specific ice_dcb.c to ice_common.c so that the driver always has access to this AQ command. Signed-off-by:
-
David S. Miller authored
Jisheng Zhang says: ==================== net: stmmac: improve WOL Currently, stmmac driver relies on the HW PMT to support WOL. We want to support phy based WOL. patch1 is a small improvement to disable WAKE_MAGIC for PMT case if no pmt_magic_frame. patch2 and patch3 are two prepation patches. patch4 implement the phy based WOL patch5 tries to save a bit energy if WOL is enabled. ==================== Signed-off-by: -
Jisheng Zhang authored
When WoL is enabled and the machine is powered off, the PHY remains waiting for wakeup events at max speed, which is a waste of energy. Slow down the PHY speed before stopping the ethernet if WoL is enabled, Signed-off-by:
-
Jisheng Zhang authored
Currently, the stmmac driver WOL implementation relies on MAC's PMT feature. We have a case: the MAC HW doesn't enable PMT, instead, we rely on the phy to support WOL. Implement the support for this case. Signed-off-by:
-
Jisheng Zhang authored
This is to prepare WOL support with phy. Compared with WOL implementation which relies on the MAC's PMT features, in phy supported WOL case, device_may_wakeup() may also be true, but we should not call mac's pmt() function if HW doesn't enable PMT. And during resume, we should call phylink_start() if PMT is disabled. Signed-off-by:
-
Jisheng Zhang authored
If !device_can_wakeup(), there's no need to futher check. And return -EOPNOTSUPP rather than -EINVAL if !device_can_wakeup(). Signed-off-by:
-
Jisheng Zhang authored
Remove WAKE_MAGIC from supported modes if the HW capability register shows no support for pmt_magic_frame. Signed-off-by:
-
David S. Miller authored
Linus Walleij says: ==================== RTL8366 VLAN callback fixes While we are pondering how to make the core set up the VLANs the right way, let's merge the uncontroversial fixes. ==================== Signed-off-by: -
Linus Walleij authored
Alter the rtl8366_vlan_add() to call rtl8366_set_vlan() inside the loop that goes over all VIDs since we now properly support calling that function more than once. Augment the loop to postincrement as this is more intuitive. The loop moved past the last VID but called rtl8366_set_vlan() with the port number instead of the VID, assuming a 1-to-1 correspondence between ports and VIDs. This was also a bug. Cc: DENG Qingfang <dqfext@gmail.com> Cc: Mauri Sandberg <sandberg@mailfence.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Fixes: d8652956 ("net: dsa: realtek-smi: Add Realtek SMI driver") Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Linus Walleij authored
The RTL8366 would not handle adding new members (ports) to a VLAN: the code assumed that ->port_vlan_add() was only called once for a single port. When intializing the switch with .configure_vlan_while_not_filtering set to true, the function is called numerous times for adding all ports to VLAN1, which was something the code could not handle. Alter rtl8366_set_vlan() to just |= new members and untagged flags to 4k and MC VLAN table entries alike. This makes it possible to just add new ports to a VLAN. Put in some helpful debug code that can be used to find any further bugs here. Cc: DENG Qingfang <dqfext@gmail.com> Cc: Mauri Sandberg <sandberg@mailfence.com> Reviewed-by:
-
Brian Vazquez authored
This avoids another inderect call per RX packet which save us around 20-40 ns. Changelog: v1 -> v2: - Move declaraions to fib_rules.h to remove warnings Reported-by:
kernel test robot <lkp@intel.com> Signed-off-by:
-
Cong Wang authored
When red_init() fails, red_destroy() is called to clean up. If the timer is not initialized yet, del_timer_sync() will complain. So we have to move timer_setup() before any failure. Reported-and-tested-by: syzbot+6e95a4fabf88dc217145@syzkaller.appspotmail.com Fixes: aee9caa0 ("net: sched: sch_red: Add qevents "early_drop" and "mark"") Cc: Petr Machata <petrm@mellanox.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by:
Petr Machata <petrm@mellanox.com> Signed-off-by:
-
David S. Miller authored
Luo bin says: ==================== hinic: add some error messages for debug patch #1: support to handle hw abnormal event patch #2: improve the error messages when functions return failure and dump relevant registers in some exception handling processes ==================== Signed-off-by: -
Luo bin authored
improve the error message when functions return failure and dump relevant registers in some exception handling processes Signed-off-by:
Luo bin <luobin9@huawei.com> Signed-off-by:
-
Luo bin authored
add support to handle hw abnormal event such as hardware failure, cable unplugged,link error Signed-off-by:
-
David S. Miller authored
Jacob Keller says: ==================== introduce PLDM firmware update library This series goal is to enable support for updating the ice hardware flash using the devlink flash command. The ice firmware update files are distributed using the file format described by the "PLDM for Firmware Update" standard: https://www.dmtf.org/documents/pmci/pldm-firmware-update-specification-100 Because this file format is standard, this series introduces a new library that handles the generic logic for parsing the PLDM file header. The library uses a design that is very similar to the Mellanox mlxfw module. That is, a simple ops table is setup and device drivers instantiate an instance of the pldmfw library with the device specific operations. Doing so allows for each device to implement the low level behavior for how to interact with its firmware. This series includes the library and an implementation for the ice hardware. I've removed all of the parameters, and the proposed changes to support overwrite mode. I'll be working on the overwrite mask suggestion from Jakub as a follow-up series. Because the PLDM file format is a standard and not something that is specific to the Intel hardware, I opted to place this update library in lib/pldmfw. I should note that while I tried to make the library generic, it does not attempt to mimic the complete "Update Agent" as defined in the standard. This is mostly due to the fact that the actual interfaces exposed to software for the ice hardware would not allow this. This series depends on some work just recently and is based on top of the patch series sent by Tony published at: https://lore.kernel.org/netdev/20200723234720.1547308-1-anthony.l.nguyen@intel.com/T/#t Changes since v2 RFC * Removed overwrite mode patches, as this can become a follow up series with a separate discussion * Fixed a minor bug in the pldm_timestamp structure not being packed. * Dropped Cc for other driver maintainers, as this series no longer includes changes to the core flash update command. * Re-ordered patches slightly. Changes since v1 RFC * Removed the "allow_downgrade_on_flash_update" parameter. Instead, the driver will always attempt to flash the device, even when firmware indicates that it would be a downgrade. A dev_warn is used to indicate when this occurs. * Removed the "ignore_pending_flash_update". Instead, the driver will always check for and cancel any previous pending update. A devlink flash status message will be sent when this cancellation occurs. * Removed the "reset_after_flash_update" parameter. This will instead be implemented as part of a devlink reset interface, work left for a future change. * Replaced the "flash_update_preservation_level" parameter with a new "overwrite" mode attribute on the flash update command. For ice, this mode will select the preservation level. For all other drivers, I modified them to check that the mode is "OVERWRITE_NOTHING", and have Cc'd the maintainers to get their input. ==================== Signed-off-by:
-
