Not all graphic page remappers support physical addresses over the 4GB
mark for remapping, so while some do (the AMD64 GART always did, and I
just fixed the i965 to do so properly), we're safest off just forcing
GFP_DMA32 allocations to make sure graphics pages get allocated in the
low 32-bit address space by default.

AGP sub-drivers that really care, and can do better, could just choose
to implement their own allocator (or we could add another "64-bit safe"
default allocator for their use), but quite frankly, you're not likely
to care in practice.

So for now, this trivial change means that we won't be allocating pages
that we can't map correctly by mistake on x86-64.

[ On traditional 32-bit x86, this could never happen, because GFP_KERNEL
  would never allocate any highmem memory anyway ]
Acked-by: Andi Kleen <ak@suse.de>
Acked-by: Dave Jones <davej@redhat.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This introduces a i965-specific "mask_memory()" function that knows
about the extended physical addresses that the i965 supports.  This
allows us to correctly map in physical memory in the >4GB range into the
GTT.

Also simplify/clean-up the i965 case for the aperture sizing by just
returning the fixed 512kB size from "fetch_size()".  We don't really
care that not all of the aperture may be visible - the only thing that
cares about the aperture size is the Intel "stolen memory" calculation,
which depends on the fixed size.

Cc: Keith Packard <keithp@keithp.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This reverts commit f72fa707, and solves
the problem that it tried to fix by simply making "__do_IRQ()" call the
note_interrupt() function without the lock held, the way everybody else
does.

It should be noted that all interrupt handling code must never allow the
descriptor actors to be entered "recursively" (that's why we do all the
magic IRQ_PENDING stuff in the first place), so there actually is
exclusion at that much higher level, even in the absense of locking.
Acked-by: Vivek Goyal <vgoyal@in.ibm.com>
Acked-by: Pavel Emelianov <xemul@openvz.org>
Cc: Andrew Morton <akpm@osdl.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

* 'merge' of master.kernel.org:/pub/scm/linux/kernel/git/paulus/powerpc:
  [POWERPC] Fix ucc_geth of_device discovery on mpc832x
  [POWERPC] Revert "[POWERPC] Add powerpc get/set_rtc_time interface to new generic rtc class"
  [POWERPC] Revert "[POWERPC] Enable generic rtc hook for the MPC8349 mITX"

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [TG3]: Add missing unlock in tg3_open() error path.
  [IPV6]: Fix address/interface handling in UDP and DCCP, according to the scoping architecture.
  [IRDA]: Lockdep fix.
  [BLUETOOTH]: Fix unaligned access in hci_send_to_sock.
  [XFRM]: nlmsg length not computed correctly in the presence of subpolicies
  [XFRM]: Sub-policies broke policy events
  [IGMP]: Fix IGMPV3_EXP() normalization bit shift value.
  [Bluetooth] Ignore L2CAP config requests on disconnect
  [Bluetooth] Always include MTU in L2CAP config responses
  [Bluetooth] Check if RFCOMM session is still attached to the TTY
  [Bluetooth] Handling pending connect attempts after inquiry
  [Bluetooth] Attach low-level connections to the Bluetooth bus
  [IPV6] IP6TUNNEL: Add missing nf_reset() on input path.
  [IPV6] IP6TUNNEL: Delete all tunnel device when unloading module.
  [IPV6] ROUTE: Do not enable router reachability probing in router mode.
  [IPV6] ROUTE: Prefer reachable nexthop only if the caller requests.
  [IPV6] ROUTE: Try to use router which is not known unreachable.

mpc832x, as in mpc8360, needs to explicitly find and create the
platform device for ucc_geth in 2.6.19.  This code will likely be
readapted to Benh's new of_ methods for 2.6.20.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Sparse noticed a locking imbalance in tg3_open(). This patch adds an
unlock to one of the error paths, so that tg3_open() always exits
without the lock held.
Signed-off-by: Ira W. Snyder <kernel@irasnyder.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TCP and RAW do not have this issue.  Closes Bug #7432.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

On Sat, 2006-11-18 at 16:12 +0300, Andrey Borzenkov wrote:

> =============================================
> [ INFO: possible recursive locking detected ]
> 2.6.19-rc5-2avb #2
> - ---------------------------------------------
> pppd/26425 is trying to acquire lock:
>  (&hashbin->hb_spinlock){....}, at: [<dfdea87a>] irlmp_slsap_inuse+0x5a/0x170
> [irda]
>
> but task is already holding lock:
>  (&hashbin->hb_spinlock){....}, at: [<dfdea857>] irlmp_slsap_inuse+0x37/0x170
> [irda]
>
> other info that might help us debug this:
> 1 lock held by pppd/26425:
>  #0:  (&hashbin->hb_spinlock){....}, at: [<dfdea857>]
> irlmp_slsap_inuse+0x37/0x170 [irda]
>
> stack backtrace:
>  [<c010413c>] dump_trace+0x1cc/0x200
>  [<c010418a>] show_trace_log_lvl+0x1a/0x30
>  [<c01047f2>] show_trace+0x12/0x20
>  [<c01048c9>] dump_stack+0x19/0x20
>  [<c01346ca>] __lock_acquire+0x8fa/0xc20
>  [<c0134d2d>] lock_acquire+0x5d/0x80
>  [<c02a851c>] _spin_lock+0x2c/0x40
>  [<dfdea87a>] irlmp_slsap_inuse+0x5a/0x170 [irda]
>  [<dfdebab2>] irlmp_open_lsap+0x62/0x180 [irda]
>  [<dfdf35d1>] irttp_open_tsap+0x181/0x230 [irda]
>  [<dfdc0c3d>] ircomm_open_tsap+0x5d/0xa0 [ircomm]
>  [<dfdc05d8>] ircomm_open+0xb8/0xd0 [ircomm]
>  [<dfdd0477>] ircomm_tty_open+0x4f7/0x570 [ircomm_tty]
>  [<c020bbe4>] tty_open+0x174/0x340
>  [<c016bd69>] chrdev_open+0x89/0x170
>  [<c0167bd6>] __dentry_open+0xa6/0x1d0
>  [<c0167da5>] nameidata_to_filp+0x35/0x40
>  [<c0167df9>] do_filp_open+0x49/0x50
>  [<c0167e47>] do_sys_open+0x47/0xd0
>  [<c0167f0c>] sys_open+0x1c/0x20
>  [<c010307d>] sysenter_past_esp+0x56/0x8d
>  [<b7f86410>] 0xb7f86410
>  =======================

The comment at the nesting lock says:

	/* Careful for priority inversions here !
	 * irlmp->links is never taken while another IrDA
	 * spinlock is held, so we are safe. Jean II */

So, under the assumption the author was right, it just needs a lockdep
annotation.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 7a69af63.

As advised by David Brownell:

http://marc.theaimsgroup.com/?l=linux-kernel&m=116387226902131&w=2Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

This reverts commit a8ed4f7e.

As advised by David Brownell:

http://marc.theaimsgroup.com/?l=linux-kernel&m=116387226902131&w=2Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The "u16 *" derefs of skb->data need to be wrapped inside of
a get_unaligned().

Thanks to Gustavo Zacarias for the bug report.
Signed-off-by: David S. Miller <davem@davemloft.net>

I actually dont have a test case for these; i just found them by
inspection. Refer to patch "[XFRM]: Sub-policies broke policy events"
for more info
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Acked-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

XFRM policy events are broken when sub-policy feature is turned on.
A simple test to verify this:
run ip xfrm mon on one window and add then delete a policy on another
window ..
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Acked-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The IGMPV3_EXP() macro doesn't correctly shift the normalization bit, so
time-out values are longer than they should be.

Thanks to Dirk Ooms for finding the problem in IGMPv3 - MLDv2 had a
similar problem that was already fixed a year ago. :-(
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Any L2CAP connection in disconnecting state shall not response
to any further config requests from the remote side. So in case
such a request is received, ignore it.
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When sending a positive config response it shall include the actual
MTU to be used on this channel. This differs from the Bluetooth 1.1
specification where it was enough to acknowledge the config request.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

If the RFCOMM session is no longer attached to the TTY device, then it
makes no sense to go through with changing the termios settings.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

After an inquiry completed or got canceled the Bluetooth core should
check for any pending connect attempts.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

To receive uvents for the low-level ACL and SCO links, they must be
assigned to a subsystem. It is enough to attach them to the already
established Bluetooth bus.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>

Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>

RFC4191 explicitly states that the procedures are applicable to
hosts only.  We should not have changed behavior of routers.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>

Only routers in "FAILED" state should be considered unreachable.
Otherwise, we do not try to use speicific routes unless all least specific
routers are considered unreachable.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>

The ONDEMAND governor needs FREQ_TABLE
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6:
  [PATCH] x86_64: Align data segment to PAGE_SIZE boundary
  [PATCH] x86-64: increase PHB1 split transaction timeout
  [PATCH] x86-64: Fix C3 timer test

o Explicitly align data segment to PAGE_SIZE boundary otherwise depending on
  config options and tool chain it might be placed on a non PAGE_SIZE aligned
  boundary and vmlinux loaders like kexec fail when they encounter a
  PT_LOAD type segment which is not aligned to PAGE_SIZE boundary.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>

SGI-PV: 958376
SGI-Modid: xfs-linux-melb:xfs-kern:27503a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>

xfs_bmap_add_extent_delay_real()

SGI-PV: 957008
SGI-Modid: xfs-linux-melb:xfs-kern:27457a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Shailendra Tripathi <stripathi@agami.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>

ipath uses skb functions and won't build without CONFIG_NET.

Spotted by Randy Dunlap.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

This is a quick hack to overcome the fact that SRCU currently does not
allow static initializers, and we need to sometimes initialize those
things before any other initializers (even "core" ones) can do so.

Currently we don't allow this at all for modules, and the only user that
needs is right now is cpufreq. As reported by Thomas Gleixner:

   "Commit b4dfdbb3 ("[PATCH] cpufreq:
    make the transition_notifier chain use SRCU breaks cpu frequency
    notification users, which register the callback > on core_init
    level."

Cc: Thomas Gleixner <tglx@timesys.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Andrew Morton <akpm@osdl.org>,
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
  IPoIB: Clear high octet in QP number

Switch to using irq_handler_t for interrupt function handler pointers.

Change name of m68knommu's irq_hanlder_t data structure so it doesn't
clash with the common type (include/linux/interrupt.h).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Fix a build error for the  enter:now PCI card.
Signed-off-by: Toralf Foerster <toralf.foerster@gmx.de>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Fix printk format warnings:
drivers/char/ftape/zftape/zftape-buffers.c:87: warning: format '%d' expects type
'int', but argument 3 has type 'size_t'
drivers/char/ftape/zftape/zftape-buffers.c:104: warning: format '%d' expects type
 'int', but argument 3 has type 'size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This is to fix compile error of x86-64 memory hotplug without any NUMA
option.

  CC      arch/x86_64/mm/init.o
arch/x86_64/mm/init.c:501: error: redefinition of 'memory_add_physaddr_to_nid'
include/linux/memory_hotplug.h:71: error: previous definition of 'memory_add_phys
addr_to_nid' was here
arch/x86_64/mm/init.c:509: error: redefinition of 'memory_add_physaddr_to_nid'
arch/x86_64/mm/init.c:501: error: previous definition of 'memory_add_physaddr_to_
nid' was here

I confirmed compile completion with !NUMA, (NUMA & !ACPI_NUMA),
or (NUMA & ACPI_NUMA).
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Acked-by: Andi Kleen <ak@suse.de>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

i2c_bit_add_bus() returns -E;
-E != 0		=>	err = 1
probe fails with positive error code
Signed-off-by: Alexey Dobriyan <adobriyan@openvz.org>
Cc: Deepak Saxena <dsaxena@mvista.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>