Skip to content

L
linux
Switch branch/tag
  1. 12 Aug, 2007 14 commits
    • Len Brown's avatar
      Pull dock-bay into release branch · 6712a4fb
      Len Brown authored
      6712a4fb
    • Len Brown's avatar
      Pull bugzilla-8842 into release branch · d8dd3cbc
      Len Brown authored
      d8dd3cbc
    • Len Brown's avatar
      Pull bugzilla-8768 into release branch · fc0dc4d3
      Len Brown authored
      fc0dc4d3
    • Len Brown's avatar
      Pull bugzilla-3774 into release branch · 53fdc518
      Len Brown authored
      53fdc518
    • Len Brown's avatar
      pull asus sony thinkpad into release branch · 3b6919e5
      Len Brown authored
      3b6919e5
    • Len Brown's avatar
      ACPI: thermal: add DMI hooks to handle AOpen's broken Award BIOS · 0b5bfa1c
      Len Brown authored 
      Use DMI to:
1. enable polling (BIOS thermal events are broken)
2. disable active trip points (BIOS fan control is broken)
3. disable passive trip point (BIOS hard-codes it too low)

The actual temperature reading does work,
and with the aid of polling, the critical
trip point should work too.

http://bugzilla.kernel.org/show_bug.cgi?id=8842Signed-off-by: default avatarLen Brown <len.brown@intel.com>
      0b5bfa1c
    • Len Brown's avatar
      ACPI: thermal: create "thermal.act=" to disable or override active trip point · f8707ec9
      Len Brown authored 
      thermal.act=-1 disables all active trip points
in all ACPI thermal zones.

thermal.act=C, where C > 0, overrides all lowest temperature
active trip points in all thermal zones to C degrees Celsius.
Raising this trip-point may allow you to keep your system silent
up to a higher temperature.  However, it will not allow you to
raise the lowest temperature trip point above the next higher
trip point (if there is one).  Lowering this trip point may
kick in the fan sooner.

Note that overriding this trip-point will disable any BIOS attempts
to implement hysteresis around the lowest temperature trip point.
This may result in the fan starting and stopping frequently
if temperature frequently crosses C.

WARNING: raising trip points above the manufacturer's defaults
may cause the system to run at higher temperature and shorten
its life.
Signed-off-by: default avatarLen Brown <len.brown@intel.com>
      f8707ec9
    • Len Brown's avatar
      ACPI: thermal: create "thermal.nocrt" to disable critical actions · f5487145
      Len Brown authored 
      thermal.nocrt=1 disables actions on _CRT and _HOT
ACPI thermal zone trip-points.  They will be marked
as <disabled> in /proc/acpi/thermal_zone/*/trip_points.

There are two cases where this option is used:

1. Debugging a hot system crossing valid trip point.

   If your system fan is spinning at full speed,
   be sure that the vent is not clogged with dust.
   Many laptops have very fine thermal fins that are easily blocked.

   Check that the processor fan-sink is properly seated,
   has the proper thermal grease, and is really spinning.

   Check for fan related options in BIOS SETUP.
   Sometimes there is a performance vs quiet option.
   Defaults are generally the most conservative.

   If your fan is not spinning, yet /proc/acpi/fan/
   has files in it, please file a Linux/ACPI bug.

   WARNING: you risk shortening the lifetime of your
   hardware if you use this parameter on a hot system.
   Note that this refers to all system components,
   including the disk drive.

2. Working around a cool system crossing critical
   trip point due to erroneous temperature reading.

   Try again with CONFIG_HWMON=n
   There is known potential for conflict between the
   the hwmon sub-system and the ACPI BIOS.
   If this fixes it, notify lm-sensors@lm-sensors.org
   and linux-acpi@vger.kernel.org

   Otherwise, file a Linux/ACPI bug, or notify
   just linux-acpi@vger.kernel.org.
Signed-off-by: default avatarLen Brown <len.brown@intel.com>
      f5487145
    • Len Brown's avatar
      ACPI: thermal: create "thermal.psv=" to override passive trip points · a70cdc52
      Len Brown authored 
      "thermal.psv=-1" disables passive trip points
for all ACPI thermal zones.

"thermal.psv=C", where 'C' is degrees Celsius,
overrides all existing passive trip points
for all ACPI thermal zones.

thermal.psv is checked at module load time,
and in response to trip-point change events.

Note that if the system does not deliver thermal zone
temperature change events near the new trip-point,
then it will not be noticed.  To force your custom
trip point to be noticed, you may need to enable polling:
eg. thermal.tzp=3000 invokes polling every 5 minutes.

Note that once passive thermal throttling is invoked,
it has its own internal Thermal Sampling Period (_TSP),
that is unrelated to _TZP.

WARNING: disabling or raising a thermal trip point
may result in increased running temperature and
shorter hardware lifetime on some systems.
Signed-off-by: default avatarLen Brown <len.brown@intel.com>
      a70cdc52
    • Len Brown's avatar
      ACPI: thermal: expose "thermal.tzp=" to set global polling frequency · 730ff34d
      Len Brown authored 
      Thermal Zone Polling frequency (_TZP) is an optional ACPI object
recommending the rate that the OS should poll the associated thermal zone.

If _TZP is 0, no polling should be used.
If _TZP is non-zero, then the platform recommends that
the OS poll the thermal zone at the specified rate.
The minimum period is 30 seconds.
The maximum period is 5 minutes.

(note _TZP and thermal.tzp units are in deci-seconds,
 so _TZP = 300 corresponds to 30 seconds)

If _TZP is not present, ACPI 3.0b recommends that the
thermal zone be polled at an "OS provided default frequency".

However, common industry practice is:
1. The BIOS never specifies any _TZP
2. High volume OS's from this century never poll any thermal zones

Ie. The OS depends on the platform's ability to
provoke thermal events when necessary, and
the "OS provided default frequency" is "never":-)

There is a proposal that ACPI 4.0 be updated to reflect
common industry practice -- ie. no _TZP, no polling.

The Linux kernel already follows this practice --
thermal zones are not polled unless _TZP is present and non-zero.

But thermal zone polling is useful as a workaround for systems
which have ACPI thermal control, but have an issue preventing
thermal events.  Indeed, some Linux distributions still
set a non-zero thermal polling frequency for this reason.

But rather than ask the user to write a polling frequency
into all the /proc/acpi/thermal_zone/*/polling_frequency
files, here we simply document and expose the already
existing module parameter to do the same at system level,
to simplify debugging those broken platforms.

Note that thermal.tzp is a module-load time parameter only.
Signed-off-by: default avatarLen Brown <len.brown@intel.com>
      730ff34d
    • Len Brown's avatar
      ACPI: thermal: create "thermal.off=1" to disable ACPI thermal support · 72b33ef8
      Len Brown authored 
      "thermal.off=1" disables all ACPI thermal support at boot time.

CONFIG_ACPI_THERMAL=n can do this at build time.
"# rmmod thermal" can do this at run time,
as long as thermal is built as a module.

WARNING: On some systems, disabling ACPI thermal support
will cause the system to run hotter and reduce the
lifetime of the hardware.
Signed-off-by: default avatarLen Brown <len.brown@intel.com>
      72b33ef8
    • Henrique de Moraes Holschuh's avatar
      ACPI: thinkpad-acpi: fix sysfs paths in documentation · 9de1cc4a
      Henrique de Moraes Holschuh authored 
      The documentation used "thinkpad-acpi" to refer to the directories in
sysfs, while it should have been using "thinkpad_acpi".  Thanks to Hugh
Dickins for the error report.

I wish I could just call the module and everything else by the proper
name with the "-", instead of using these ugly translations to "_".
Signed-off-by: default avatarHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: default avatarLen Brown <len.brown@intel.com>
      9de1cc4a
    • Holger Macht's avatar
      ACPI: dock: Send key=value pair instead of plain value · 66b56821
      Holger Macht authored 
      Send key=value pair along with the uevent instead of a plain value so that
userspace (udev) can handle it like common environment variables.
Signed-off-by: default avatarHolger Macht <hmacht@suse.de>
Acked-by: default avatarKristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Stephan Berberig <s.berberig@arcor.de>
Signed-off-by: default avatarAndrew Morton <akpm@linux-foundation.org>
Acked-by: default avatarGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: default avatarLen Brown <len.brown@intel.com>
      66b56821
    • Stephan Berberig's avatar
      ACPI: bay: send envp with uevent - fix · 7aa763cb
      Stephan Berberig authored 
      There must not be a new-line character in the uevent.  Otherwise, udev gets
confused.  Thanks to Kay Sievers for pointing it out.
Signed-off-by: default avatarStephan Berberig <s.berberig@arcor.de>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: default avatarAndrew Morton <akpm@linux-foundation.org>
Acked-by: default avatarGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: default avatarLen Brown <len.brown@intel.com>
      7aa763cb
  3. 11 Aug, 2007 26 commits
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7