cxgb4 : Integrate DCBx support into cxgb4 module. Register dbcnl_ops to give access to DCBx functions
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4 : Update fw interface file for DCBx support. Adds all the required fields to fw interface to communicate DCBx info
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The time comparsion functions require arguments of type unsigned long
instead of (signed) long.
Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcf_ematch is allocated by kzalloc in function tcf_em_tree_validate(),
so cm_old is always NULL.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

use list_for_each_entry_continue_reverse to rollback in fdb_add_hw
when add address failed
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2014-06-20

This series contains updates to i40e and i40evf.

Anjali provides an update to the registers to handle the updates from the
hardware.  Also provides a fix so that we do not try to access the rings
through the qvectors at the time of freeing the qvectors.

Jesse provides a workaround for some older NVM versions where the NVM
was not filling in the GLQF_HKEY register, so made sure that the
critical register is initialized.

Michal provides a fix to reset the head and tail on admin queue
initialization where head and tail are not reset by the hardware.

Neerav adds a helper routine that would wait for the Rx/Tx queue to reach
the enable or disable state that is requested.  Also provides a fix
to the debugfs command "lldp get remote" which was dumping the local
LLDPDU instead of the peer's LLDPDU.  Fixed a bug when all the Tx hang
recovery mechanisms have failed and the driver tries to bring down the
interface in the interrupt context.

Shannon provides a patch to clear the Virtual Ethernet Bridge (VEB) stats
when the PF stats are cleared.  Also cleans the service tasks so that
they do not run while a reset is in progress.

Mitch fixes an issue in i40evf_get_rxfh() where only fifteen registers
were being read instead of all sixteen.

Carolyn provides a change to the RSS configuration to set table size and
write to the hardware to confirm the RSS table size being used.

Kamil makes a change to the admin queue debug prints so that they will not
cause segmentation faults in some of our tool applications.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Bump versions.

Change-ID: Ifaed5404b9e953a11f4c88953ffe4bc8937705f1
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Some AQ debug prints needs be moved around or do additional checks so they
will not cause our tool applications to cause segmentation faults.
The tools run in user space and we need to correctly reference kernel
space memory.

Change-ID: Ia2ac4076f576b805f350453fd50ad69c2a91ab9a
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch changes the RSS configuration to set table size
and write to hardware to confirm RSS table size being used.

Change-ID: I455a4c09c9dd479f5791ee1f09fdc83ff9908df5
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix checkpatch warning:
WARNING: kfree(NULL) is safe this check is probably not required

Cc: Ariel Elior <ariele@broadcom.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix checkpatch warning:
WARNING: kfree(NULL) is safe this check is probably not required

Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

The RNDIS_STATUS_NETWORK_CHANGE event is received after the Hyper-V host
sleep or hibernation. We refresh network at this time.
MS-TFS: 135162
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The loop in i40evf_get_rxfh_indir was only reading fifteen registers,
not all sixteen. Change the matching loop in i40evf_set_rxfh_indir at
the same time to make the code more consistent.

Change-ID: I6c182287698e742d1f6ca1a4bcc43cc08df6e1de
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Make sure the service tasks don't try to meddle with the
device while a reset is in progress.  Odd things can happen
such as funky stats values.

Change-ID: I6929cb9d6d96839c9279362ca7c0e3fe6c8fcc66
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The VEB really is part of the whole PF and should be cleared
at the same time.

Change-ID: Ia1d4d1df5cf421f2578a22486650dd256cc4617a
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The bug is encountered when all the Tx hang recovery mechanisms have
failed and driver tries to bring down the interface in the interrupt context.
The patch defers this and schedules it for next cycle.

Change-ID: Id9cd1da15b0e5c018dce18da4d0eed5ef1e8a809
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix the debugfs command "lldp get remote" that dumped the local
LLDPDU instead of peer's LLDPDU.

Change-ID: I0702eacdafd54478c18f20cab3a7fa5dc1b3182d
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Introduce helper routines that would wait for the Rx/Tx queue
to reach the enable or disable state as requested.

Change-ID: I518d9d0e2afef3f45107af3b46e9af402ff587c3
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When we resize the number of queues, the driver needs to disassociate any
qvectors that are no longer in use from the original rings, this way we
do not try to access the rings through these qvectors at the time of freeing
the qvectors.

Change-ID: Ie4eb9fc749f8e12348517fe1560f599c58f4a2a4
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Reset head and tail on admin queue initialization where H/T are
not reset by HW.

Change-ID: I6db8a2dd3f05ce66410a92cce016191add04760e
Signed-off-by: Michal Kosiarz <michal.kosiarz@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The NVM wasn't filling in the GLQF_HKEY register on
some old NVM versions.  If this is the case, fill
in some values so receive with flow rules works right.

Change-ID: Ic737888ee68f96efb4cf8a1a49d2301615e09ed2
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This updates the register file for new hardware.
The format of the file has changed requiring drivers to
declare I40E_MASK. I40E_MASK is to be used with 32 bit registers.

This patch also updates the drivers to accommodate the register changes.

Change-ID: If9bc8d736391024cbf99054efe50f9acc12ee4f1
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ir_mark initialization is done for both TCP v4 and v6, move it in the
common tcp_openreq_init function.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In __dev_open(), it already calls dev_set_rx_mode().
and dev_set_rx_mode() has no effect for a net device which does not have
IFF_UP flag set.

So the call of dev_set_rx_mode() is duplicate in __dev_change_flags().
Signed-off-by: Weiping Pan <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

separate the mrf24j40 hardware initialisation from probe()
and adds the sanity checkings.

These checkings are required if somebody hasn't a right spi configuration
the probe function should fail. So we have to return from there.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Fix checksumming regressions, from Tom Herbert.

 2) Undo unintentional permissions changes for SCTP rto_alpha and
    rto_beta sysfs knobs, from Denial Borkmann.

 3) VXLAN, like other IP tunnels, should advertize it's encapsulation
    size using dev->needed_headroom instead of dev->hard_header_len.
    From Cong Wang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  net: sctp: fix permissions for rto_alpha and rto_beta knobs
  vxlan: Checksum fixes
  net: add skb_pop_rcv_encapsulation
  udp: call __skb_checksum_complete when doing full checksum
  net: Fix save software checksum complete
  net: Fix GSO constants to match NETIF flags
  udp: ipv4: do not waste time in __udp4_lib_mcast_demux_lookup
  vxlan: use dev->needed_headroom instead of dev->hard_header_len
  MAINTAINERS: update cxgb4 maintainer

Pull more clock framework updates from Mike Turquette:
 "This contains the second half the of the clk changes for 3.16.

  They are simply fixes and code refactoring for the OMAP clock drivers.
  The sunxi clock driver changes include splitting out the one
  mega-driver into several smaller pieces and adding support for the A31
  SoC clocks"

* tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux: (25 commits)
  clk: sunxi: document PRCM clock compatible strings
  clk: sunxi: add PRCM (Power/Reset/Clock Management) clks support
  clk: sun6i: Protect SDRAM gating bit
  clk: sun6i: Protect CPU clock
  clk: sunxi: Rework clock protection code
  clk: sunxi: Move the GMAC clock to a file of its own
  clk: sunxi: Move the 24M oscillator to a file of its own
  clk: sunxi: Remove calls to clk_put
  clk: sunxi: document new A31 USB clock compatible
  clk: sunxi: Implement A31 USB clock
  ARM: dts: OMAP5/DRA7: use omap5-mpu-dpll-clock capable of dealing with higher frequencies
  CLK: TI: dpll: support OMAP5 MPU DPLL that need special handling for higher frequencies
  ARM: OMAP5+: dpll: support Duty Cycle Correction(DCC)
  CLK: TI: clk-54xx: Set the rate for dpll_abe_m2x2_ck
  CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)
  dt:/bindings: DRA7 ATL (Audio Tracking Logic) clock bindings
  ARM: dts: dra7xx-clocks: Correct name for atl clkin3 clock
  CLK: TI: gate: add composite interface clock to OMAP2 only build
  ARM: OMAP2: clock: add DT boot support for cpufreq_ck
  CLK: TI: OMAP2: add clock init support
  ...

Pull NVMe update from Matthew Wilcox:
 "Mostly bugfixes again for the NVMe driver.  I'd like to call out the
  exported tracepoint in the block layer; I believe Keith has cleared
  this with Jens.

  We've had a few reports from people who're really pounding on NVMe
  devices at scale, hence the timeout changes (and new module
  parameters), hotplug cpu deadlock, tracepoints, and minor performance
  tweaks"

[ Jens hadn't seen that tracepoint thing, but is ok with it - it will
  end up going away when mq conversion happens ]

* git://git.infradead.org/users/willy/linux-nvme: (22 commits)
  NVMe: Fix START_STOP_UNIT Scsi->NVMe translation.
  NVMe: Use Log Page constants in SCSI emulation
  NVMe: Define Log Page constants
  NVMe: Fix hot cpu notification dead lock
  NVMe: Rename io_timeout to nvme_io_timeout
  NVMe: Use last bytes of f/w rev SCSI Inquiry
  NVMe: Adhere to request queue block accounting enable/disable
  NVMe: Fix nvme get/put queue semantics
  NVMe: Delete NVME_GET_FEAT_TEMP_THRESH
  NVMe: Make admin timeout a module parameter
  NVMe: Make iod bio timeout a parameter
  NVMe: Prevent possible NULL pointer dereference
  NVMe: Fix the buffer size passed in GetLogPage(CDW10.NUMD)
  NVMe: Update data structures for NVMe 1.2
  NVMe: Enable BUILD_BUG_ON checks
  NVMe: Update namespace and controller identify structures to the 1.1a spec
  NVMe: Flush with data support
  NVMe: Configure support for block flush
  NVMe: Add tracepoints
  NVMe: Protect against badly formatted CQEs
  ...

Commit 3fd091e7 ("[SCTP]: Remove multiple levels of msecs
to jiffies conversions.") has silently changed permissions for
rto_alpha and rto_beta knobs from 0644 to 0444. The purpose of
this was to discourage users from tweaking rto_alpha and
rto_beta knobs in production environments since they are key
to correctly compute rtt/srtt.

RFC4960 under section 6.3.1. RTO Calculation says regarding
rto_alpha and rto_beta under rule C3 and C4:

  [...]
  C3)  When a new RTT measurement R' is made, set

       RTTVAR <- (1 - RTO.Beta) * RTTVAR + RTO.Beta * |SRTT - R'|

       and

       SRTT <- (1 - RTO.Alpha) * SRTT + RTO.Alpha * R'

       Note: The value of SRTT used in the update to RTTVAR
       is its value before updating SRTT itself using the
       second assignment. After the computation, update
       RTO <- SRTT + 4 * RTTVAR.

  C4)  When data is in flight and when allowed by rule C5
       below, a new RTT measurement MUST be made each round
       trip. Furthermore, new RTT measurements SHOULD be
       made no more than once per round trip for a given
       destination transport address. There are two reasons
       for this recommendation: First, it appears that
       measuring more frequently often does not in practice
       yield any significant benefit [ALLMAN99]; second,
       if measurements are made more often, then the values
       of RTO.Alpha and RTO.Beta in rule C3 above should be
       adjusted so that SRTT and RTTVAR still adjust to
       changes at roughly the same rate (in terms of how many
       round trips it takes them to reflect new values) as
       they would if making only one measurement per
       round-trip and using RTO.Alpha and RTO.Beta as given
       in rule C3. However, the exact nature of these
       adjustments remains a research issue.
  [...]

While it is discouraged to adjust rto_alpha and rto_beta
and not further specified how to adjust them, the RFC also
doesn't explicitly forbid it, but rather gives a RECOMMENDED
default value (rto_alpha=3, rto_beta=2). We have a couple
of users relying on the old permissions before they got
changed. That said, if someone really has the urge to adjust
them, we could allow it with a warning in the log.

Fixes: 3fd091e7 ("[SCTP]: Remove multiple levels of msecs to jiffies conversions.")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tom Herbert says:

====================
Fixes related to some recent checksum modifications.

- Fix GSO constants to match NETIF flags
- Fix logic in saving checksum complete in __skb_checksum_complete
- Call __skb_checksum_complete from UDP if we are checksumming over
  whole packet in order to save checksum.
- Fixes to VXLAN to work correctly with checksum complete
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Call skb_pop_rcv_encapsulation and postpull_rcsum for the Ethernet
header to work properly with checksum complete.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This function is used by UDP encapsulation protocols in RX when
crossing encapsulation boundary. If ip_summed is set to
CHECKSUM_UNNECESSARY and encapsulation is not set, change to
CHECKSUM_NONE since the checksum has not been validated within the
encapsulation. Clears csum_valid by the same rationale.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In __udp_lib_checksum_complete check if checksum is being done over all
the data (len is equal to skb->len) and if it is call
__skb_checksum_complete instead of __skb_checksum_complete_head. This
allows checksum to be saved in checksum complete.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Geert reported issues regarding checksum complete and UDP.
The logic introduced in commit 7e3cead5
("net: Save software checksum complete") is not correct.

This patch:
1) Restores code in __skb_checksum_complete_header except for setting
   CHECKSUM_UNNECESSARY. This function may be calculating checksum on
   something less than skb->len.
2) Adds saving checksum to __skb_checksum_complete. The full packet
   checksum 0..skb->len is calculated without adding in pseudo header.
   This value is saved in skb->csum and then the pseudo header is added
   to that to derive the checksum for validation.
3) In both __skb_checksum_complete_header and __skb_checksum_complete,
   set skb->csum_valid to whether checksum of zero was computed. This
   allows skb_csum_unnecessary to return true without changing to
   CHECKSUM_UNNECESSARY which was done previously.
4) Copy new csum related bits in __copy_skb_header.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Joseph Gasparakis reported that VXLAN GSO offload stopped working with
i40e device after recent UDP changes. The problem is that the
SKB_GSO_* bits are out of sync with the corresponding NETIF flags. This
patch fixes that. Also, we add BUILD_BUG_ONs in net_gso_ok for several
GSO constants that were missing to avoid the problem in the future.
Reported-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull more SCSI updates from James Bottomley:
 "This is just a couple of drivers (hpsa and lpfc) that got left out for
  further testing in linux-next.  We also have one fix to a prior
  submission (qla2xxx sparse)"

* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (36 commits)
  qla2xxx: fix sparse warnings introduced by previous target mode t10-dif patch
  lpfc: Update lpfc version to driver version 10.2.8001.0
  lpfc: Fix ExpressLane priority setup
  lpfc: mark old devices as obsolete
  lpfc: Fix for initializing RRQ bitmap
  lpfc: Fix for cleaning up stale ring flag and sp_queue_event entries
  lpfc: Update lpfc version to driver version 10.2.8000.0
  lpfc: Update Copyright on changed files from 8.3.45 patches
  lpfc: Update Copyright on changed files
  lpfc: Fixed locking for scsi task management commands
  lpfc: Convert runtime references to old xlane cfg param to fof cfg param
  lpfc: Fix FW dump using sysfs
  lpfc: Fix SLI4 s abort loop to process all FCP rings and under ring_lock
  lpfc: Fixed kernel panic in lpfc_abort_handler
  lpfc: Fix locking for postbufq when freeing
  lpfc: Fix locking for lpfc_hba_down_post
  lpfc: Fix dynamic transitions of FirstBurst from on to off
  hpsa: fix handling of hpsa_volume_offline return value
  hpsa: return -ENOMEM not -1 on kzalloc failure in hpsa_get_device_id
  hpsa: remove messages about volume status VPD inquiry page not supported
  ...

Pull more btrfs updates from Chris Mason:
 "This has a few fixes since our last pull and a new ioctl for doing
  btree searches from userland.  It's very similar to the existing
  ioctl, but lets us return larger items back down to the app"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: fix error handling in create_pending_snapshot
  btrfs: fix use of uninit "ret" in end_extent_writepage()
  btrfs: free ulist in qgroup_shared_accounting() error path
  Btrfs: fix qgroups sanity test crash or hang
  btrfs: prevent RCU warning when dereferencing radix tree slot
  Btrfs: fix unfinished readahead thread for raid5/6 degraded mounting
  btrfs: new ioctl TREE_SEARCH_V2
  btrfs: tree_search, search_ioctl: direct copy to userspace
  btrfs: new function read_extent_buffer_to_user
  btrfs: tree_search, copy_to_sk: return needed size on EOVERFLOW
  btrfs: tree_search, copy_to_sk: return EOVERFLOW for too small buffer
  btrfs: tree_search, search_ioctl: accept varying buffer
  btrfs: tree_search: eliminate redundant nr_items check

Pull aio fix and cleanups from Ben LaHaise:
 "This consists of a couple of code cleanups plus a minor bug fix"

* git://git.kvack.org/~bcrl/aio-next:
  aio: cleanup: flatten kill_ioctx()
  aio: report error from io_destroy() when threads race in io_destroy()
  fs/aio.c: Remove ctx parameter in kiocb_cancel