- 10 May, 2013 2 commits
-
-
James Bottomley authored
lpfc uses the generic checksum as well as the T10DIF one from the lib/ directory, so make sure they're selected. Reported-by:
Randy Dunlap <rdunlap@infradead.org> Signed-off-by:
James Bottomley <JBottomley@Parallels.com>
-
Hannes Reinecke authored
scsi_send_eh_cmnd() is calling queuecommand() directly, so it needs to check the return value here. The only valid return codes for queuecommand() are 'busy' states, so we need to wait for a bit to allow the LLDD to recover. Based on an earlier patch from Wen Xiong. [jejb: fix confusion between msec and jiffies values and other issues] [bvanassche: correct stall_for interval] Cc: Wen Xiong <wenxiong@linux.vnet.ibm.com> Cc: Brian King <brking@linux.vnet.ibm.com> Signed-off-by:
Hannes Reinecke <hare@suse.de> Signed-off-by:
-
- 02 May, 2013 38 commits
-
-
Vikas Chaudhary authored
Increment 'ha->iocb_cnt' before adding mbox_iocb to iocb queue. Signed-off-by:
Vikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by:
-
Vinayak Holikatti authored
This patch corrects the expected data transfer size of the command UPIU. The current implementation of cmd->transfersize is wrong as it probably equal to sector size. With this implementation the transfer size is updated correctly Reported-by:
KOBAYASHI Yoshitake <yoshitake.kobayashi@toshiba.co.jp> Reviewed-by:
Arnd Bergmann <arnd@arndb.de> Reviewed-by:
Namjae Jeon <linkinjeon@gmail.com> Reviewed-by:
Subhash Jadavani <subhashj@codeaurora.org> Tested-by:
Maya Erez <merez@codeaurora.org> Signed-off-by:
Santosh Yaraganavi <santoshsy@gmail.com> Signed-off-by:
Vinayak Holikatti <vinholikatti@gmail.com> Signed-off-by:
-
Vinayak Holikatti authored
This patch adds Platform glue driver for ufshcd. Reviewed-by:
Sujit Reddy Thumma <sthumma@codeaurora.org> Tested-by:
-
James Bottomley authored
Some arrays synchronize their full non volatile cache when the sd driver sends a SYNCHRONIZE CACHE command. Unfortunately, they can have Terrabytes of this and we send a SYNCHRONIZE CACHE for every barrier if an array reports it has a writeback cache. This leads to massive slowdowns on journalled filesystems. The fix is to allow userspace to turn off the writeback cache setting as a temporary measure (i.e. without doing the MODE SELECT to write it back to the device), so even though the device reported it has a writeback cache, the user, knowing that the cache is non volatile and all they care about is filesystem correctness, can turn that bit off in the kernel and avoid the performance ruinous (and safety irrelevant) SYNCHRONIZE CACHE commands. The way you do this is add a 'temporary' prefix when performing the usual cache setting operations, so echo temporary write through > /sys/class/scsi_disk/<disk>/cache_type Reported-by:
Ric Wheeler <rwheeler@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Fengguang Wu authored
Signed-off-by:
Fengguang Wu <fengguang.wu@intel.com> Signed-off-by:
Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by:
-
Armen Baloyan authored
Found by 0 day test project Reported-by:
Armen Baloyan <armen.baloyan@qlogic.com> Signed-off-by:
-
Akinobu Mita authored
provisioning map (map_storep) is a bitmap accessed by bitops. So the allocation size should be a multiple of sizeof(unsigned long) and also the bitmap should be cleared by using bitmap_clear() instead of memset(). Otherwise it will cause problem on big-endian architecture if the number of bits is not a multiple of BITS_PER_LONG. I tried testing the logical block provisioning support in scsi_debug, but it didn't work as I expected. For example, load scsi_debug module with UNMAP command supported and fill the storage with random data. # modprobe scsi_debug lbpu=1 # dd if=/dev/urandom of=/dev/sdb Then, try to unmap LBA 0, but Get LBA status reports: # sg_unmap --lba=0 --num=1 /dev/sdb # sg_get_lba_status --lba=0 /dev/sdb descriptor LBA: 0x0000000000000000 blocks: 16384 mapped This is unexpected result. Because UNMAP command to LBA 0 finished without any errors, but Get LBA status shows that LBA 0 is still mapped. This problem is due to the wrong translation between LBA and index of provisioning map. Fix it by using correct translation functions. Signed-off-by:Akinobu Mita <akinobu.mita@gmail.com> Acked-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Akinobu Mita authored
The function unmap_region() clears memory region specified as the logical block address and the number of logical blocks in ramdisk storage (fake_storep) if lbpu and lbprz module parameters are enabled. In the while loop of unmap_region(), it advances optimal unmap granularity in logical blocks. But it only clears one logical block at LBA 'block' per loop iteration. And furthermore, the 'block' is not pointing to a logical block address which should be cleared, it is a index of probisioning map (map_storep). Signed-off-by:
-
Akinobu Mita authored
scsi_debug prohibits setting scsi_debug_unmap_alignment to be greater than scsi_debug_unmap_granularity. But setting them to be the same value is not prohibited. In this case, the only difference with scsi_debug_unmap_alignment == 0 is the logical blocks from 0 to scsi_debug_unmap_alignment - 1 cannot be unmapped. But the difference is not properly handled in the current code. So this prohibits such unusual setting. Signed-off-by:
-
Akinobu Mita authored
If the logical block provisioning is not enabled, map_region() and unmap_region() have no effect and they don't need to be called. So this makes map_region() and unmap_region() to be called only when scsi_debug_lbp() returns true, i.e. logical block provisioning is enabled. While I'm at it, this also removes meaningless non-zero check for scsi_debug_unmap_granularity. Because scsi_debug_unmap_granularity cannot be zero with usual setting: scsi_debug_unmap_granularity is 1 by default, and it can be changed to zero with explicit module parameter setting only when the logical block provisioning is disabled. But it is only meaningful module parameter when the logical block provisioning is enabled. Signed-off-by:
-
Jeremy Higdon authored
It appears to me that there is a problem with handling of type 1 protection information. It is considering a logical block reference tag of 0xffffffff to be an error, but it is actually valid any time ((lba & 0xffffffff) == 0xffffffff) [for example, 2TiB-1, 4TiB-1, 6TiB-1, etc.]. I'm going by what's written in 4.18.3 of SBC3, where there doesn't appear to be any invalid value for the reference tag. Signed-off-by:
Jeremy Higdon <jeremy@sgi.com> Acked-by:
-
wenxiong@linux.vnet.ibm.com authored
Driver passed the wrong IOADL address to IOA adapter. The patch fixes the issue. Signed-off-by:
Wen Xiong <wenxiong@linux.vnet.ibm.com> Acked-by:
Brian King <brking@linux.vnet.ibm.com> Signed-off-by:
-
Wei Yongjun authored
Fix to return -ENOMEM in the create workqueue error case instead of 0, as done elsewhere in this function. Signed-off-by:
Wei Yongjun <yongjun_wei@trendmicro.com.cn> Reviewed-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
-
James Smart authored
Signed-off-by:
James Smart <james.smart@emulex.com> Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
[SCSI] lpfc 8.3.39: Reduced tmo value set to FLOGI WQE for quick recovery from FLOGI sequence timeout Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
[SCSI] lpfc 8.3.39: Fixed system panic during EEH recovery due to midlayer acting on outstanding I/O Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
wenxiong@linux.vnet.ibm.com authored
Add reset adapter after the 6th EEH errors in ipr driver. This triggers the adapter reset via the PCI config space even when the slot is frozen. Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
-
Adheer Chandravanshi authored
Assign values using correct datatype in function qla4xxx_copy_to_fwddb_param() Signed-off-by:
Adheer Chandravanshi <adheer.chandravanshi@qlogic.com> Signed-off-by:
-
