PHYLIB is not selected by the mvusb driver but it uses mdio devres
helpers. Explicitly select MDIO_DEVRES in this driver's Kconfig entry.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 1814cff2 ("net: phy: add a Kconfig option for mdio_devres")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a missing return statement to atalk_proc_init so it doesn't return
-ENOMEM when successful.  This allows the appletalk module to load
properly.

Fixes: e2bcd8b0 ("appletalk: use remove_proc_subtree to simplify procfs code")
Link: https://www.downtowndougbrown.com/2020/08/hacking-up-a-fix-for-the-broken-appletalk-kernel-module-in-linux-5-1-and-newer/Reported-by: Christopher KOBAYASHI <chris@disavowed.jp>
Reported-by: Doug Brown <doug@downtowndougbrown.com>
Signed-off-by: Vincent Duvert <vincent.ldev@duvert.net>
[lukas: add missing tags]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v5.1+
Cc: Yue Haibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds full 802.1q VLAN support to the qca8k, allowing the use of
vlan_filtering and more complicated bridging setups than allowed by
basic port VLAN support.

Tested with a number of untagged ports with separate VLANs and then a
trunk port with all the VLANs tagged on it.

v3:
- Pull QCA8K_PORT_VID_DEF changes into separate cleanup patch
- Reverse Christmas tree notation for variable definitions
- Use untagged instead of tagged for consistency
v2:
- Return sensible errnos on failure rather than -1 (rmk)
- Style cleanups based on Florian's feedback
- Silently allow VLAN 0 as device correctly treats this as no tag
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rather than using a magic value of 1 when configuring the port VIDs add
a QCA8K_PORT_VID_DEF define and use that instead. Also fix up the
bitmask in the process; the top 4 bits are reserved so this wasn't a
problem, but only masking 12 bits is the correct approach.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
100GbE Intel Wired LAN Driver Updates 2020-08-01

This series contains updates to the ice driver only.

Wei Yongjun marks power management functions with __maybe_unused.

Nick disables VLAN pruning in promiscuous mode and renames grst_delay to
grst_timeout.

Kiran modifies the check for linearization and corrects the vsi_id mask
value.

Vignesh replaces the use of flow profile locks to RSS profile locks for RSS
rule removal. Destroys flow profile lock on clearing XLT table and
clears extraction sequence entries.

Jesse adds some statistics and removes an unreported one.

Brett allows for 2 queue configuration for VFs.

Surabhi adds a check for failed allocation of an extraction sequence
table.

Tony updates the PTYPE lookup table and makes other trivial fixes.

Victor extends profile ID locks to be held until all references are
completed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When we don't care about vlan depth, we could pass NULL instead of the
address of a unused local variable to skb_network_protocol() as a param.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In fact, skb_pagelen() - skb_headlen() is equal to __skb_pagelen(), use it
directly to avoid unnecessary skb_headlen() call.

Also fix the CHECK note of checkpatch.pl:
    Comparison to NULL could be written "!__pskb_pull_tail"
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use eth_zero_addr() to clear mac address instead of memset().
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use eth_zero_addr() to clear mac address instead of memset().
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit c8729cac ("cxgb4: add ethtool n-tuple filter insertion")
has removed checking control key for determining IP address types
for TC-FLOWER rules, which causes all the rules being inserted to
hardware to become IPv6 rule type always. So, add back the check
to select the correct IP address type to extract and hence fix the
correct rule type being inserted to hardware.

Also, ethtool_rx_flow_key doesn't have any control key and instead
directly sets the IPv4/IPv6 address keys. So, explicitly set the
IP address type for ethtool n-tuple filters to reuse the same code.

Fixes: c8729cac ("cxgb4: add ethtool n-tuple filter insertion")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The flag indicating the selftest to run is a bitmask. So, fix the
check. Also, the selftests will fail if adapter initialization has
not been completed yet. So, add appropriate check and bail sooner.

Fixes: 7235ffae ("cxgb4: add loopback ethtool self-test")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shannon Nelson says:

====================
ionic txrx updates

These are a few patches to do some cleanup in the packet
handling and give us more flexibility in tuning performance
by allowing us to put Tx handling on separate interrupts
when it makes sense for particular traffic loads.

v3: simplified queue count change logging, removed unnecessary
    check for no count change
v2: dropped the original patch 2 for ringsize change
    changed the separated tx/rx interrupts to use ethtool -L
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the capability to split the Tx queues onto their own
interrupts with their own napi contexts.  This gives the
opportunity for more direct control of Tx interrupt
handling, such as CPU affinity and interrupt coalescing,
useful for some traffic loads.

v2: use ethtool -L, not a vendor specific priv-flag
v3: simplify logging, drop unnecessary "no-change" tests
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

We give the tx clean path its own budget and service routine in
order to give a little more leeway to be more aggressive, and
in preparation for coming changes.  We've found this gives us
a little better performance in some packet processing scenarios
without hurting other scenarios.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

We really don't need to hit the Rx queue doorbell so many times,
we can wait to the end and cause a little less thrash.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

The GRE tunnel can be used to transport traffic that does not rely on a
Internet checksum (e.g. SCTP). The issue can be triggered creating a GRE
or GRETAP tunnel and transmitting SCTP traffic ontop of it where CRC
offload has been disabled. In order to fix the issue we need to
recompute the GRE csum in gre_gso_segment() not relying on the inner
checksum.
The issue is still present when we have the CRC offload enabled.
In this case we need to disable the CRC offload if we require GRE
checksum since otherwise skb_checksum() will report a wrong value.

Fixes: 90017acc ("sctp: Add GSO support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to clear all of the bridge private skb variables as they can be
stale due to the packet being recirculated through the stack and then
transmitted through the bridge device. Similar memset is already done on
bridge's input. We've seen cases where proxyarp_replied was 1 on routed
multicast packets transmitted through the bridge to ports with neigh
suppress which were getting dropped. Same thing can in theory happen with
the port isolation bit as well.

Fixes: 821f1b21 ("bridge: add new BR_NEIGH_SUPPRESS port flag to suppress arp and nd flood")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

"how" was used as a boolean. Change the type to bool, and improve
variable name
Signed-off-by: Florent Fourcot <florent.fourcot@wifirst.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Second parameter of addrconf_ifdown "how" is used as a boolean
internally. It does not make sense to call it with something different
of 0 or 1.

This value is set to 2 in all git history.
Signed-off-by: Florent Fourcot <florent.fourcot@wifirst.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eelco Chaudron says:

====================
net: openvswitch: masks cache enhancements

This patchset adds two enhancements to the Open vSwitch masks cache.

Changes in v4 [patch 2/2 only]:
 - Remove null check before calling free_percpu()
 - Make ovs_dp_change() return appropriate error codes

Changes in v3 [patch 2/2 only]:
 - Use is_power_of_2() function
 - Use array_size() function
 - Fix remaining sparse errors

Changes in v2 [patch 2/2 only]:
 - Fix sparse warnings
 - Fix netlink policy items reported by Florian Westphal
====================
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch makes the masks cache size configurable, or with
a size of 0, disable it.
Reviewed-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a counter that counts the number of masks cache hits, and
export it through the megaflow netlink statistics.
Reviewed-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Release skb memory in mvpp2_rx() if mvpp2_rx_refill routine fails

Fixes: b5015854 ("net: mvpp2: fix refilling BM pools in RX path")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

info cannot be NULL here since its being accessed earlier
in the function: nlmsg_parse(info->nlhdr...). Remove this
redundant NULL check.
Signed-off-by: Gaurav Singh <gaurav1086@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

ovs_ct_put_key() is potentially copying uninitialized kernel stack memory
into socket buffers, since the compiler may leave a 3-byte hole at the end
of `struct ovs_key_ct_tuple_ipv4` and `struct ovs_key_ct_tuple_ipv6`. Fix
it by initializing `orig` with memset().

Fixes: 9dd7f890 ("openvswitch: Add original direction conntrack tuple to sw_flow_key.")
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When openvswitch conntrack offload with act_ct action. Fragment packets
defrag in the ingress tc act_ct action and miss the next chain. Then the
packet pass to the openvswitch datapath without the mru. The over
mtu packet will be dropped in output action in openvswitch for over mtu.

"kernel: net2: dropped over-mtu packet: 1528 > 1500"

This patch add mru in the tc_skb_ext for adefrag and miss next chain
situation. And also add mru in the qdisc_skb_cb. The act_ct set the mru
to the qdisc_skb_cb when the packet defrag. And When the chain miss,
The mru is set to tc_skb_ext which can be got by ovs datapath.

Fixes: b57dc7c1 ("net/sched: Introduce action ct")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bruno Thomsen says:

====================
Improve MDIO Ethernet PHY reset

This patch series is a result of trying to upstream a new device
tree for a TQMa7D based board[1][2]. Initial this DTS used some
deprecated PHY reset properties on the FEC device; NXP Ethernet
MAC also known as Freescale Fast Ethernet Controller.

When switching from FEC properties[3]:
"phy-reset-gpios"
"phy-reset-duration"
"phy-reset-post-delay"

To MDIO PHY properties[4]:
"reset-gpios"
"reset-assert-us"
"reset-deassert-us"

The result was that no Ethernet PHY device was detected on boot.

This issue could be worked around by disabling PHY type ID auto-
detection by using "ethernet-phy-id0022.1560" as compatible
string and not "ethernet-phy-ieee802.3-c22".

Upstreaming a DTS with this workaround was not accepted, so I
digged into the MDIO reset flow and found that it had a few
missing parts compared to the deprecated FEC reset function.
After some more testing and logic analyzer traces it was
revealed that the failed PHY communication was due to missing
initial device reset.

I was suggested[5] in a earlier mail thread to use MDIO bus
reset as that was performed before auto-detection, but current
device tree binding was limited to reset assert in usec.
Microchip/Micrel Ethernet PHYs recommended reset circuit[8],
figure 7-12, is a little "slow" after reset deassert as that
is left to a RC circuit with a tau of ~100ms; using a 10k PU
resistor together with a 10uF decoupling capacitor. The diode
in serie of the reset signal converts the GPIO push-pull output
into a open-drain output. So a post reset delay in the range
of 500-1000ms is needed, depending on component tolerances
and general hardware design margins.

In the first version of this patch series[6] I reused the
"reset-delay-us" property for reset deassert in usec as that
would cause 50/50% duty-cycle, but that would always apply.
The solution in this patch series is to add a new MDIO bus
property, so post reset delay is optional and configured
separately.

MDIO bus properties[7]:
"reset-delay-us"
"reset-post-delay-us" (new)

I have not marked this with "Fixes:" as no single commit is the
cause and historically this code has only supported MDIO devices
that need reset after auto-detection. The patch series also uses
a new flexible sleep helper function that was introduced in
5.8-rc1, so the driver uses the optimal sleep function depending
on value loaded from device tree.

Future work in this area could add new properties on the MDIO
device, so reset points are configurable, e.g. no reset,
before/after auto-detection or both.

[1] https://lore.kernel.org/linux-devicetree/20200629114927.17379-2-bruno.thomsen@gmail.com/
[2] https://lore.kernel.org/linux-devicetree/20200716172611.5349-2-bruno.thomsen@gmail.com/
[3] https://elixir.bootlin.com/linux/v5.7.8/source/Documentation/devicetree/bindings/net/fsl-fec.txt#L44
[4] https://elixir.bootlin.com/linux/v5.8-rc4/source/Documentation/devicetree/bindings/net/mdio.yaml#L78
[5] https://lore.kernel.org/netdev/CAOMZO5DtYDomD8FDCZDwYCSr2AwNT81Ay4==aDxXyBxtyvPiJA@mail.gmail.com/
[6] https://lore.kernel.org/netdev/20200728090203.17313-1-bruno.thomsen@gmail.com/
[7] https://elixir.bootlin.com/linux/v5.8-rc4/source/Documentation/devicetree/bindings/net/mdio.yaml#L36
[8] http://ww1.microchip.com/downloads/en/DeviceDoc/00002202C.pdf
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

MDIO device reset assert and deassert length was created by
usleep_range() but that does not ensure optimal handling of
all the different values from device tree properties.
By switching to the new flexible sleeping helper function,
fsleep(), the correct delay function is called depending on
delay length, e.g. udelay(), usleep_range() or msleep().
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Load new "reset-post-delay-us" value from MDIO properties,
and if configured to a greater then zero delay do a
flexible sleeping delay after MDIO bus reset deassert.
This allows devices to exit reset state before start
bus communication.
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MDIO bus reset pulse width is created by using udelay()
and that function might not be optimal depending on
device tree value. By switching to the new fsleep() helper
the correct delay function is called depending on
delay length, e.g. udelay(), usleep_range() or msleep().
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add "reset-post-delay-us" parameter to MDIO bus properties,
so it's possible to add a delay after reset deassert.
This is optional in case external hardware slows down
release of the reset signal.
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Resolved kernel/bpf/btf.c using instructions from merge commit
69138b34Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Encap offset calculation is incorrect in esp6, from Sabrina Dubroca.

 2) Better parameter validation in pfkey_dump(), from Mark Salyzyn.

 3) Fix several clang issues on powerpc in selftests, from Tanner Love.

 4) cmsghdr_from_user_compat_to_kern() uses the wrong length, from Al
    Viro.

 5) Out of bounds access in mlx5e driver, from Raed Salem.

 6) Fix transfer buffer memleak in lan78xx, from Johan Havold.

 7) RCU fixups in rhashtable, from Herbert Xu.

 8) Fix ipv6 nexthop refcnt leak, from Xiyu Yang.

 9) vxlan FDB dump must be done under RCU, from Ido Schimmel.

10) Fix use after free in mlxsw, from Ido Schimmel.

11) Fix map leak in HASH_OF_MAPS bpf code, from Andrii Nakryiko.

12) Fix bug in mac80211 Tx ack status reporting, from Vasanthakumar
    Thiagarajan.

13) Fix memory leaks in IPV6_ADDRFORM code, from Cong Wang.

14) Fix bpf program reference count leaks in mlx5 during
    mlx5e_alloc_rq(), from Xin Xiong.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (86 commits)
  vxlan: fix memleak of fdb
  rds: Prevent kernel-infoleak in rds_notify_queue_get()
  net/sched: The error lable position is corrected in ct_init_module
  net/mlx5e: fix bpf_prog reference count leaks in mlx5e_alloc_rq
  net/mlx5e: E-Switch, Specify flow_source for rule with no in_port
  net/mlx5e: E-Switch, Add misc bit when misc fields changed for mirroring
  net/mlx5e: CT: Support restore ipv6 tunnel
  net: gemini: Fix missing clk_disable_unprepare() in error path of gemini_ethernet_port_probe()
  ionic: unlock queue mutex in error path
  atm: fix atm_dev refcnt leaks in atmtcp_remove_persistent
  net: ethernet: mtk_eth_soc: fix MTU warnings
  net: nixge: fix potential memory leak in nixge_probe()
  devlink: ignore -EOPNOTSUPP errors on dumpit
  rxrpc: Fix race between recvmsg and sendmsg on immediate call failure
  MAINTAINERS: Replace Thor Thayer as Altera Triple Speed Ethernet maintainer
  selftests/bpf: fix netdevsim trap_flow_action_cookie read
  ipv6: fix memory leaks on IPV6_ADDRFORM path
  net/bpfilter: Initialize pos in __bpfilter_process_sockopt
  igb: reinit_locked() should be called with rtnl_lock
  e1000e: continue to init PHY even when failed to disable ULP
  ...

Pull thread fix from Christian Brauner:
 "A simple spelling fix for dequeue_synchronous_signal()"

* tag 'for-linus-2020-08-01' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
  signal: fix typo in dequeue_synchronous_signal()

Pull perf tooling fixes from Arnaldo Carvalho de Melo:

 - Fix libtraceevent build with binutils 2.35

 - Fix memory leak in process_dynamic_array_len in libtraceevent

 - Fix 'perf test 68' zstd compression for s390

 - Fix record failure when mixed with ARM SPE event

* tag 'perf-tools-fixes-2020-08-01' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
  libtraceevent: Fix build with binutils 2.35
  perf tools: Fix record failure when mixed with ARM SPE event
  perf tests: Fix test 68 zstd compression for s390
  tools lib traceevent: Fix memory leak in process_dynamic_array_len

kernel test robot says:
net/mptcp/syncookies.c: In function 'mptcp_join_cookie_init':
include/linux/kernel.h:47:38: warning: division by zero [-Wdiv-by-zero]
 #define ARRAY_SIZE(arr) (sizeof(arr) / sizeof((arr)[0]) + __must_be_array(arr))

I forgot that spinock_t size is 0 on UP, so ARRAY_SIZE cannot be used.

Fixes: 9466a1cc ("mptcp: enable JOIN requests even if cookies are in use")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

When vxlan interface is deleted, all fdbs are deleted by vxlan_flush().
vxlan_flush() flushes fdbs but it doesn't delete fdb, which contains
all-zeros-mac because it is deleted by vxlan_uninit().
But vxlan_uninit() deletes only the fdb, which contains both all-zeros-mac
and default vni.
So, the fdb, which contains both all-zeros-mac and non-default vni
will not be deleted.

Test commands:
    ip link add vxlan0 type vxlan dstport 4789 external
    ip link set vxlan0 up
    bridge fdb add to 00:00:00:00:00:00 dst 172.0.0.1 dev vxlan0 via lo \
	    src_vni 10000 self permanent
    ip link del vxlan0

kmemleak reports as follows:
unreferenced object 0xffff9486b25ced88 (size 96):
  comm "bridge", pid 2151, jiffies 4294701712 (age 35506.901s)
  hex dump (first 32 bytes):
    02 00 00 00 ac 00 00 01 40 00 09 b1 86 94 ff ff  ........@.......
    46 02 00 00 00 00 00 00 a7 03 00 00 12 b5 6a 6b  F.............jk
  backtrace:
    [<00000000c10cf651>] vxlan_fdb_append.part.51+0x3c/0xf0 [vxlan]
    [<000000006b31a8d9>] vxlan_fdb_create+0x184/0x1a0 [vxlan]
    [<0000000049399045>] vxlan_fdb_update+0x12f/0x220 [vxlan]
    [<0000000090b1ef00>] vxlan_fdb_add+0x12a/0x1b0 [vxlan]
    [<0000000056633c2c>] rtnl_fdb_add+0x187/0x270
    [<00000000dd5dfb6b>] rtnetlink_rcv_msg+0x264/0x490
    [<00000000fc44dd54>] netlink_rcv_skb+0x4a/0x110
    [<00000000dff433e7>] netlink_unicast+0x18e/0x250
    [<00000000b87fb421>] netlink_sendmsg+0x2e9/0x400
    [<000000002ed55153>] ____sys_sendmsg+0x237/0x260
    [<00000000faa51c66>] ___sys_sendmsg+0x88/0xd0
    [<000000006c3982f1>] __sys_sendmsg+0x4e/0x80
    [<00000000a8f875d2>] do_syscall_64+0x56/0xe0
    [<000000003610eefa>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
unreferenced object 0xffff9486b1c40080 (size 128):
  comm "bridge", pid 2157, jiffies 4294701754 (age 35506.866s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 f8 dc 42 b2 86 94 ff ff  ..........B.....
    6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b  kkkkkkkkkkkkkkkk
  backtrace:
    [<00000000a2981b60>] vxlan_fdb_create+0x67/0x1a0 [vxlan]
    [<0000000049399045>] vxlan_fdb_update+0x12f/0x220 [vxlan]
    [<0000000090b1ef00>] vxlan_fdb_add+0x12a/0x1b0 [vxlan]
    [<0000000056633c2c>] rtnl_fdb_add+0x187/0x270
    [<00000000dd5dfb6b>] rtnetlink_rcv_msg+0x264/0x490
    [<00000000fc44dd54>] netlink_rcv_skb+0x4a/0x110
    [<00000000dff433e7>] netlink_unicast+0x18e/0x250
    [<00000000b87fb421>] netlink_sendmsg+0x2e9/0x400
    [<000000002ed55153>] ____sys_sendmsg+0x237/0x260
    [<00000000faa51c66>] ___sys_sendmsg+0x88/0xd0
    [<000000006c3982f1>] __sys_sendmsg+0x4e/0x80
    [<00000000a8f875d2>] do_syscall_64+0x56/0xe0
    [<000000003610eefa>] entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: 3ad7a4b1 ("vxlan: support fdb and learning in COLLECT_METADATA mode")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It turns out that on commit 41d707b7 ("fib: fix fib_rules_ops
indirect calls wrappers") I forgot to include the case when
CONFIG_IP_MULTIPLE_TABLES is not set.

Fixes: 41d707b7 ("fib: fix fib_rules_ops indirect calls wrappers")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes these errors:

net/ipv4/syncookies.c: In function 'tcp_get_cookie_sock':
net/ipv4/syncookies.c:216:19: error: 'struct tcp_request_sock' has no
member named 'drop_req'
  216 |   if (tcp_rsk(req)->drop_req) {
      |                   ^~
net/ipv4/syncookies.c: In function 'cookie_tcp_reqsk_alloc':
net/ipv4/syncookies.c:289:27: warning: unused variable 'treq'
[-Wunused-variable]
  289 |  struct tcp_request_sock *treq;
      |                           ^~~~
make[3]: *** [scripts/Makefile.build:280: net/ipv4/syncookies.o] Error 1
make[3]: *** Waiting for unfinished jobs....

Fixes: 9466a1cc ("mptcp: enable JOIN requests even if cookies are in use")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull pin control fix from Linus Walleij:
 "A single last minute pin control fix to the Qualcomm driver fixing
  missing dual edge PCH interrupts"

* tag 'pinctrl-v5.8-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: qcom: Handle broken/missing PDC dual edge IRQs on sc7180