- 11 Dec, 2009 25 commits
-
-
Sarah Sharp authored
In order to giveback a canceled URB, we must ensure that the xHCI hardware will not access the buffer in an URB. We can't modify the buffer pointers on endpoint rings without issuing and waiting for a stop endpoint command. Since URBs can be canceled in interrupt context, we can't wait on that command. The old code trusted that the host controller would respond to the command, and would giveback the URBs in the event handler. If the hardware never responds to the stop endpoint command, the URBs will never be completed, and we might hang the USB subsystem. Implement a watchdog timer that is spawned whenever a stop endpoint command is queued. If a stop endpoint command event is found on the event ring during an interrupt, we need to stop the watchdog timer with del_timer(). Since del_timer() can fail if the timer is running and waiting on the xHCI lock, we need a way to signal to the timer that everything is fine and it should exit. If we simply clear EP_HALT_PENDING, a new stop endpoint command could sneak in and set it before the watchdog timer can grab the lock. Instead we use a combination of the EP_HALT_PENDING flag and a counter for the number of pending stop endpoint commands (xhci_virt_ep->stop_cmds_pending). If we need to cancel the watchdog timer and del_timer() succeeds, we decrement the number of pending stop endpoint commands. If del_timer() fails, we leave the number of pending stop endpoint commands alone. In either case, we clear the EP_HALT_PENDING flag. The timer will decrement the number of pending stop endpoint commands once it obtains the lock. If the timer is the tail end of the last stop endpoint command (xhci_virt_ep->stop_cmds_pending == 0), and the endpoint's command is still pending (EP_HALT_PENDING is set), we assume the host is dying. The watchdog timer will set XHCI_STATE_DYING, try to halt the xHCI host, and give back all pending URBs. Various other places in the driver need to check whether the xHCI host is dying. If the interrupt handler ever notices, it should immediately stop processing events. The URB enqueue function should also return -ESHUTDOWN. The URB dequeue function should simply return the value of usb_hcd_check_unlink_urb() and the watchdog timer will take care of giving the URB back. When a device is disconnected, the xHCI hardware structures should be freed without issuing a disable slot command (since the hardware probably won't respond to it anyway). The debugging polling loop should stop polling if the host is dying. When a device is disconnected, any pending watchdog timers are killed with del_timer_sync(). It must be synchronous so that the watchdog timer doesn't attempt to access the freed endpoint structures. Signed-off-by:
Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Sarah Sharp authored
xhci_quiesce() is basically a no-op right now. It's only called if HC_IS_RUNNING() is true, and the body of the function consists of a BUG_ON if HC_IS_RUNNING() is false. For the new xHCI watchdog timer, we need a new function that clears the xHCI running bit in the command register, but doesn't wait for the halt status to show up in the status register. Re-purpose xhci_quiesce() to do that. Signed-off-by:
-
Sarah Sharp authored
In the old code, there was a race condition between the stop endpoint command and the URB submission process. When the stop endpoint command is handled by the event handler, the endpoint ring is assumed to be stopped. When a stop endpoint command is queued, URB submissions are to not ring the doorbell. The old code would check the number of pending URBs to be canceled, and would not ring the doorbell if it was non-zero. However, the following race condition could occur with the old code: 1. Cancel an URB, add it to the list of URBs to be canceled, queue the stop endpoint command, and increment ep->cancels_pending to 1. 2. The URB finishes on the HW, and an event is enqueued to the event ring (at the same time as 1). 3. The stop endpoint command finishes, and the endpoint is halted. An event is queued to the event ring. 4. The event handler sees the finished URB, notices it was to be canceled, decrements ep->cancels_pending to 0, and removes it from the to be canceled list. 5. The event handler drops the lock and gives back the URB. The completion handler requeues the URB (or a different driver enqueues a new URB). This causes the endpoint's doorbell to be rung, since ep->cancels_pending == 0. The endpoint is now running. 6. A second URB is canceled, and it's added to the canceled list. Since ep->cancels_pending == 0, a new stop endpoint command is queued, and ep->cancels_pending is incremented to 1. 7. The event handler then sees the completed stop endpoint command. The handler assumes the endpoint is stopped, but it isn't. It attempts to move the dequeue pointer or change TDs to cancel the second URB, while the hardware is actively accessing the endpoint ring. To eliminate this race condition, a new endpoint state bit is introduced, EP_HALT_PENDING. When this bit is set, a stop endpoint command has been queued, and the command handler has not begun to process the URB cancellation list yet. The endpoint doorbell should not be rung when this is set. Set this when a stop endpoint command is queued, clear it when the handler for that command runs, and check if it's set before ringing a doorbell. ep->cancels_pending is eliminated, because it is no longer used. Make sure to ring the doorbell for an endpoint when the stop endpoint command handler runs, even if the canceled URB list is empty. All canceled URBs could have completed and new URBs could have been enqueued without the doorbell being rung before the command was handled. Signed-off-by:
-
Oliver Neukum authored
usb: better error handling in usb_port_suspend - disable remote wakeup only if it was enabled - refuse to autosuspend if remote wakeup fails to be enabled Signed-off-by:
Oliver Neukum <oliver@neukum.org> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Felipe Balbi authored
this driver has been sitting in linux-omap tree for quite some time. It adds support for omap's ehci controller. Signed-off-by:
Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by:
Vikram Pandita <vikram.pandita@ti.com> Signed-off-by:
Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by:
Anand Gadiyar <gadiyar@ti.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Daniel Mack authored
This adds a minimal generic driver for ULPI connected transceivers, using the OTG framework functions recently introduced. The driver got a table to match the ULPI chips, which currently only has one entry for NXP's ISP 1504 transceiver. Signed-off-by:
Daniel Mack <daniel@caiaq.de> Cc: Heikki Krogerus <ext-heikki.krogerus@nokia.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by:
-
Daniel Mack authored
This adds support for OTG transceivers directly connected to the ULPI interface. In particular, the following details are added - a struct for low level io functions (read/write) - a priv field to be used as 'viewport' by low level access functions - an (*init) and (*shutdown) callbacks, along with static inline helpers - a (*set_vbus) callback to switch the port power on and off - a flags field for per-transceiver settings - some defines for the flags bitmask to configure platform specific details Signed-off-by:
-
David Vrabel authored
Add the wusb_phy_rate sysfs file to Wireless USB host controllers. This sets the maximum PHY rate that will be used for all connected devices. Signed-off-by:
David Vrabel <david.vrabel@csr.com> Signed-off-by:
-
David Vrabel authored
Print ep number, direction and type; and current window in asl and pzl debugfs files. Signed-off-by:
-
Oliver Neukum authored
Signed-off-by: -
Hong Xu authored
Modify both host and gadget USB drivers for at91sam9g10. This add a clock management equivalent to at91sam9261 on usb drivers. It also add the way of handling gadget pull-ups (like the at91sam9261). Signed-off-by:
Hong Xu <hong.xu@atmel.com> Signed-off-by:
Nicolas Ferre <nicolas.ferre@atmel.com>
-
Laurent Pinchart authored
Now that control requests targeted at an endpoint can be handled at the function level, move the UAC-specific control request handling code from the audio gadget driver to the audio function driver. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by:
-
Laurent Pinchart authored
Control requests targeted at an endpoint (that is sent to EP0 but specifying the target endpoint address in wIndex) are dispatched to the current configuration's setup callback, requiring all gadget drivers to dispatch the requests to the correct function driver. To avoid this, record which endpoints are used by each function in the composite driver SET CONFIGURATION handler and dispatch requests targeted at endpoints to the correct function. Signed-off-by:
-
Julia Lawall authored
Correct priority problem in the use of ! and &. The semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression E; constant C; @@ - !E & C + !(E & C) // </smpl> Signed-off-by:
Julia Lawall <julia@diku.dk> Signed-off-by:
-
David Vrabel authored
Fix type and format warning in the new sg code. Remove the very chatty debug messages that were left in by mistake and use min_t() as required (no one seems to agree on a type for buffer sizes). Reported-by:
Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by:
-
David Vrabel authored
Check urb->interval on interrupt transfers and allow those with valid values (6 <= interval <= 16). Signed-off-by:
-
David Vrabel authored
Support urbs with scatter-gather lists by trying to fit sg list elements into page lists in one or more qTDs. qTDs must end on a wMaxPacketSize boundary so if this isn't possible the urb's sg list must be copied into bounce buffers. Signed-off-by:
-
David Vrabel authored
The WHCI HCD will also support urbs with scatter-gather lists. Add a usb_bus field to indicated how many sg list elements are supported by the HCD. Use this to decide whether to pass the scatter-list to the HCD or not. Make the usb-storage driver use this new field. Signed-off-by:
-
Jean Delvare authored
I can't see any reason why these would not be static. Signed-off-by:
Jean Delvare <khali@linux-fr.org> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by:
-
Julie Zhu authored
Add bus glue driver for Xilinx USB host controller. The controller can be configured as HS only or HS/FS hybrid. The driver uses the device tree file to configure the driver according to the setting in the hardware system. This driver has been tested with usbtest using the NET2280 PCI card. Signed-off-by:
Julie Zhu <julie.zhu@xilinx.com> Signed-off-by:
John Linn <john.linn@xilinx.com> Acked-by:
Grant Likely <grant.likely@secretlab.ca> Signed-off-by:
-
Matthew Wilcox authored
Use dev_dbg() instead of an unconditional printk(KERN_DEBUG). This has two benefits; one is that it identifies the USB device which the messages related to, and the other is that the messages won't be produced unless debug is turned on. Enable the debug messages when CONFIG_USB_STORAGE_DEBUG is set. Signed-off-by:
Matthew Wilcox <willy@linux.intel.com> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Matthew Wilcox authored
Instead of reporting "SCSI emulation for USB Mass Storage devices", report "usb-storage 1-4:1.0". Signed-off-by:
-
Matthew Wilcox authored
Knowing which configuration was chosen is a debugging aid more than it is informational. Signed-off-by:
-
Jason Wessel authored
No need to check ehci->debug twice. Found-by: Sergei Shtylyov sshtylyov@ru.mvista.com Signed-off-by:
Jason Wessel <jason.wessel@windriver.com> Signed-off-by:
-
Roland Koebler authored
Add mark and space parity, since the device supports it. Signed-off-by:
Roland Koebler <r.koebler@yahoo.de> Signed-off-by:
-
- 10 Dec, 2009 15 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/tj/wqLinus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: workqueue: Add debugobjects support
-
git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xenLinus Torvalds authored
* 'bugfix' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen: xen: try harder to balloon up under memory pressure. Xen balloon: fix totalram_pages counting. xen: explicitly create/destroy stop_machine workqueues outside suspend/resume region. xen: improve error handling in do_suspend. xen: don't leak IRQs over suspend/resume. xen: call clock resume notifier on all CPUs xen: use iret for return from 64b kernel to 32b usermode xen: don't call dpm_resume_noirq() with interrupts disabled. xen: register runstate info for boot CPU early xen: register runstate on secondary CPUs xen: register timer interrupt with IRQF_TIMER xen: correctly restore pfn_to_mfn_list_list after resume xen: restore runstate_info even if !have_vcpu_info_placement xen: re-register runstate area earlier on resume. xen: wait up to 5 minutes for device connetion xen: improvement to wait_for_devices() xen: fix is_disconnected_device/exists_disconnected_device xen/xenbus: make DEVICE_ATTR()s static
-
git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xenLinus Torvalds authored
* 'xen/fbdev' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen: xen pvfb: Inhibit VM_IO flag to be set on vmalloc-ed framebuffers. fb-defio: Inhibit VM_IO flag to be set on vmalloc-ed framebuffers. fb-defio: If FBINFO_VIRTFB is defined, do not set VM_IO flag. Fix toogle whether xenbus driver should be built as module or part of kernel.
-
git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlmLinus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm: dlm: always use GFP_NOFS
-
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4Linus Torvalds authored
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (47 commits) ext4: Fix potential fiemap deadlock (mmap_sem vs. i_data_sem) ext4: Do not override ext2 or ext3 if built they are built as modules jbd2: Export jbd2_log_start_commit to fix ext4 build ext4: Fix insufficient checks in EXT4_IOC_MOVE_EXT ext4: Wait for proper transaction commit on fsync ext4: fix incorrect block reservation on quota transfer. ext4: quota macros cleanup ext4: ext4_get_reserved_space() must return bytes instead of blocks ext4: remove blocks from inode prealloc list on failure ext4: wait for log to commit when umounting ext4: Avoid data / filesystem corruption when write fails to copy data ext4: Use ext4 file system driver for ext2/ext3 file system mounts ext4: Return the PTR_ERR of the correct pointer in setup_new_group_blocks() jbd2: Add ENOMEM checking in and for jbd2_journal_write_metadata_buffer() ext4: remove unused parameter wbc from __ext4_journalled_writepage() ext4: remove encountered_congestion trace ext4: move_extent_per_page() cleanup ext4: initialize moved_len before calling ext4_move_extents() ext4: Fix double-free of blocks with EXT4_IOC_MOVE_EXT ext4: use ext4_data_block_valid() in ext4_free_blocks() ...
-
git://git.open-osd.org/linux-open-osdLinus Torvalds authored
* 'for-linus' of git://git.open-osd.org/linux-open-osd: exofs: Multi-device mirror support exofs: Move all operations to an io_engine exofs: move osd.c to ios.c exofs: statfs blocks is sectors not FS blocks exofs: Prints on mount and unmout exofs: refactor exofs_i_info initialization into common helper exofs: dbg-print less exofs: More sane debug print trivial: some small fixes in exofs documentation
-
git://git.infradead.org/ubifs-2.6Linus Torvalds authored
* git://git.infradead.org/ubifs-2.6: UBIFS: fix return code in check_leaf UBI: flush wl before clearing update marker MAINTAINERS: change e-mail of Artem Bityutskiy UBIFS: remove manual O_SYNC handling UBIFS: support mounting of UBI volume character devices UBI: Add ubi_open_volume_path
-
David Wong authored
This patch drops usage of floating point variable for 32bit build Signed-off-by:
David T. L. Wong <davidtlwong@gmail.com> Acked-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Boaz Harrosh authored
This patch changes on-disk format, it is accompanied with a parallel patch to mkfs.exofs that enables multi-device capabilities. After this patch, old exofs will refuse to mount a new formatted FS and new exofs will refuse an old format. This is done by moving the magic field offset inside the FSCB. A new FSCB *version* field was added. In the future, exofs will refuse to mount unmatched FSCB version. To up-grade or down-grade an exofs one must use mkfs.exofs --upgrade option before mounting. Introduced, a new object that contains a *device-table*. This object contains the default *data-map* and a linear array of devices information, which identifies the devices used in the filesystem. This object is only written to offline by mkfs.exofs. This is why it is kept separate from the FSCB, since the later is written to while mounted. Same partition number, same object number is used on all devices only the device varies. * define the new format, then load the device table on mount time make sure every thing is supported. * Change I/O engine to now support Mirror IO, .i.e write same data to multiple devices, read from a random device to spread the read-load from multiple clients (TODO: stripe read) Implementation notes: A few points introduced in previous patch should be mentioned here: * Special care was made so absolutlly all operation that have any chance of failing are done before any osd-request is executed. This is to minimize the need for a data consistency recovery, to only real IO errors. * Each IO state has a kref. It starts at 1, any osd-request executed will increment the kref, finally when all are executed the first ref is dropped. At IO-done, each request completion decrements the kref, the last one to return executes the internal _last_io() routine. _last_io() will call the registered io_state_done. On sync mode a caller does not supply a done method, indicating a synchronous request, the caller is put to sleep and a special io_state_done is registered that will awaken the caller. Though also in sync mode all operations are executed in parallel. Signed-off-by:Boaz Harrosh <bharrosh@panasas.com>
-
Boaz Harrosh authored
In anticipation for multi-device operations, we separate osd operations into an abstract I/O API. Currently only one device is used but later when adding more devices, we will drive all devices in parallel according to a "data_map" that describes how data is arranged on multiple devices. The file system level operates, like before, as if there is one object (inode-number) and an i_size. The io engine will split this to the same object-number but on multiple device. At first we introduce Mirror (raid 1) layout. But at the final outcome we intend to fully implement the pNFS-Objects data-map, including raid 0,4,5,6 over mirrored devices, over multiple device-groups. And more. See: http://tools.ietf.org/html/draft-ietf-nfsv4-pnfs-obj-12 * Define an io_state based API for accessing osd storage devices in an abstract way. Usage: First a caller allocates an io state with: exofs_get_io_state(struct exofs_sb_info *sbi, struct exofs_io_state** ios); Then calles one of: exofs_sbi_create(struct exofs_io_state *ios); exofs_sbi_remove(struct exofs_io_state *ios); exofs_sbi_write(struct exofs_io_state *ios); exofs_sbi_read(struct exofs_io_state *ios); exofs_oi_truncate(struct exofs_i_info *oi, u64 new_len); And when done exofs_put_io_state(struct exofs_io_state *ios); * Convert all source files to use this new API * Convert from bio_alloc to bio_kmalloc * In io engine we make use of the now fixed osd_req_decode_sense There are no functional changes or on disk additions after this patch. Signed-off-by:
-
Boaz Harrosh authored
If I do a "git mv" together with a massive code change and commit in one patch, git looses the rename and records a delete/new instead. This is bad because I want a rename recorded so later rebased/cherry-picked patches to the old name will work. Also the --follow is lost. Signed-off-by: -
Boaz Harrosh authored
Even though exofs has a 4k block size, statfs blocks is in sectors (512 bytes). Also if target returns 0 for capacity then make it ULLONG_MAX. df does not like zero-size filesystems Signed-off-by: -
Boaz Harrosh authored
It is important to print in the logs when a filesystem was mounted and eventually unmounted. Print the osd-device's osd_name and pid the FS was mounted/unmounted on. TODO: How to also print the namespace path the filesystem was mounted on? Signed-off-by: -
Boaz Harrosh authored
There are two places that initialize inodes: exofs_iget() and exofs_new_inode() As more members of exofs_i_info that need initialization are added this code will grow. (soon) Signed-off-by: -
Boaz Harrosh authored
Iner-loops printing is converted to EXOFS_DBG2 which is #defined to nothing. It is now almost bareable to just leave debug-on. Every operation is printed once, with most relevant info (I hope). Signed-off-by:
-
