- 02 Feb, 2012 29 commits
-
-
Amit Beka authored
Added a check on the direct register access. Checks that the address is in the lower ragnge (0x0-0x2000), which belongs to CSR, HBUS and FH registers. Signed-off-by: Amit Beka <amit.beka@intel.com> Signed-off-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
-
Johannes Berg authored
smatch correctly complains: iwl-trans-pcie.c +1528 iwl_trans_pcie_start_hw(50) warn: 'trans->irq' was not released on error Fix it. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
-
Don Fry authored
The routines dealing with the ucode are spread through several files. Move them all to the same file and create a iwl-ucode.h file with the ucode file definitions. Signed-off-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Don Fry authored
There is nothing device specific in the initialization of the bcast_sta_id so move it to the common inititalization routine. Signed-off-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Don Fry authored
change a comment to be a little more clear Signed-off-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
The message was misleading when a queue is deactivated. The fifo number is irrelevant then, so don't print it. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
This trans_ops->stop_hw leaves the RFKILL interrupt enabled, we can call that one instead of enable_rfkill_int. By that, we reduce the numbers of acceesses to the NIC from the upper layers. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
The HW revision is now read by the transport layer in its allocation. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
Get this information from the transport layer. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
Get this information from the transport layer. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
Get this information from the transport layer which is now in charge of the APM too. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
This handler was called from the transport layer only. Merge it to the transport's apm_init. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
Now there is only one transport function that launch a specific fw: trans_ops->start_fw. This one replaces trans_ops->start_device and trans_ops->kick_nic. The code that actually loads the fw to the device has been moved to the transport specific code. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
This is another clean up of the proble flow. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
This handler stops the HW and puts it in low power state. It will allow to clean up the flows in the upper layers. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
This is transport related Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
Kill the trans_ops->prepare_card_hw which is now useless. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
This handler will become thicker, reflect its real role now. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
This is transport related Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
From now on, the transport layer in charge of providing access to the device. So change all the driver to give a pointer to the transport to all the low level functions that actually access the device. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
Most of the accesses to the registers are done from the transport layer. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
All the bus configuration is now done in the transport allocation fucntion. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
Change the way we alloc the transport on the way. Since the transport is allocated from a bus specific area, we can give the bus specific parameters (i.e. pci_dev for PCI) to the transport. This will be useful when the bus layer will be killed. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
Allocating the shrd area dynamically will allow more agility while revamping the flows. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
There is no link between the two. Ensure that the NIC is on outside the code of the EEPROM handling. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Gregory Greenman authored
This patch connects IDI transport to driver. It does so by using a number of ifdefs at this stage. IDI is a new transport that is under development. Signed-off-by: Gregory Greenman <gregory.greenman@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
Define a new handler in the transport layer API: fw_alive. Move iwl_reset_ict to this new handler, and move the content of tx_start to this handler. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Wey-Yi Guy authored
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into wireless-next
-
- 30 Jan, 2012 11 commits
-
-
Larry Finger authored
This patch addresses a kernel bugzilla report and two recent mail threads. The kernel bugzilla report is https://bugzilla.kernel.org/show_bug.cgi?id=42632, which reports a udev timeout on boot. The first mail thread, which was on LKML (http://lkml.indiana.edu/hypermail/ linux/kernel/1112.3/00965.html) was for a WARNING that occurs after a suspend/resume cycle for rtl8192cu. The scond mail thread (http://marc.info/?l=linux-wireless&m=132655490826766&w=2) concerned changes in udev that break drivers that delay while firmware is loaded on modprobe. This patch converts all rtlwifi-based drivers to use the asynchronous firmware loading mechanism. Drivers rtl8192ce, rtl8192cu and rtl8192de share a common callback routine. Driver rtl8192se needs different handling of the firmware, thus it has its own code. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith Manoharan authored
channelFlags doesn't contain the operating HT mode. Use IS_CHAN_HT40 to determine if the current channel is in HT40 mode. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Sujith Manoharan authored
This patch modifies ath9k_htc to load the needed firmware in an asynchronous manner, fixing timeouts that were introduced with the new udev changes. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Rafał Miłecki authored
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
Whenever the PAN (P2P) context is active, it has timers in the uCode that prevent sleep, so scanning can't be out of channel for more than the beacon interval programmed into the device. Before this patch, a full scan including any passive channels when P2P was active would stall forever because it wouldn't find time to execute the passive requests (for default beacon intervals of 100 TU.) Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Wey-Yi Guy authored
Led has no use for some platform. Add additional module parameter option to disable LED Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
Fix multiple bugs in event tracing: 1) If you enable uCode tracing with the device down, it will still attempt to access the device and continuously log "MAC is in deep sleep!" errors. Fix this by only starting logging when the device is actually alive. 2) Now you can set the flag when the device is down, but logging doesn't happen when you bring it up. To fix that, start logging when the device comes alive. This means we don't log before -- we could do that but I don't need it right now. 3) For some reason we read the error instead of the event log -- use the right pointer. 4) Optimise SRAM reading of event log header. 5) Fix reading write pointer == capacity, which can happen due to racy SRAM access 6) Most importantly: fix an error where we would try to read WAY too many events (like 2^32-300) when we read the wrap counter before it is updated by the uCode -- this does happen in practice and will cause the driver to hang the machine. 7) Finally, change the timer to 10ms instead of 100ms as 100ms is too slow to capture all data with a normal event log and with 100ms the log will wrap multiple times before we have a chance to read it. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Wey-Yi Guy authored
Fix few places of typo Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Helmut Schaa authored
Unted the assumption that the sta struct is still accessible before the synchronize_rcu call we should move the num_sta_ps counter decrement after synchronize_rcu to avoid incorrect decrements if num_sta_ps. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Simon Wunderlich authored
* Handle MCS masks set by the user. * Match rates provided by the rate control algorithm to the mask set, also in HT mode, and switch back to legacy mode if necessary. * add debugfs files to observate the rate selection Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Simon Wunderlich authored
Allow to set mcs masks through nl80211. We also allow to set MCS rates but no legacy rates (and vice versa). Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-