The function get_user() can sleep while trying to fetch instruction
from user address space and causes the following warning from the
scheduler.

BUG: sleeping function called from invalid context

Though interrupts get enabled back but it happens bit later after
get_user() is called. This change moves enabling these interrupts
earlier covering the function get_user(). While at this, lets check
for kernel mode and crash as this interrupt should not have been
triggered from the kernel context.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The recent LPM changes to setup_rfi_flush() are causing some section
mismatch warnings because we removed the __init annotation on
setup_rfi_flush():

  The function setup_rfi_flush() references
  the function __init ppc64_bolted_size().
  the function __init memblock_alloc_base().

The references are actually in init_fallback_flush(), but that is
inlined into setup_rfi_flush().

These references are safe because:
 - only pseries calls setup_rfi_flush() at runtime
 - pseries always passes L1D_FLUSH_FALLBACK at boot
 - so the fallback flush area will always be allocated
 - so the check in init_fallback_flush() will always return early:
   /* Only allocate the fallback flush area once (at boot time). */
   if (l1d_flush_fallback_area)
   	return;

 - and therefore we won't actually call the freed init routines.

We should rework the code to make it safer by default rather than
relying on the above, but for now as a quick-fix just add a __ref
annotation to squash the warning.

Fixes: abf110f3 ("powerpc/rfi-flush: Make it possible to call setup_rfi_flush() again")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

If you build the kernel with CONFIG_RELOCATABLE=n, then install the
modules, rebuild the kernel with CONFIG_RELOCATABLE=y and leave the
old modules installed, we crash something like:

  Unable to handle kernel paging request for data at address 0xd000000018d66cef
  Faulting instruction address: 0xc0000000021ddd08
  Oops: Kernel access of bad area, sig: 11 [#1]
  Modules linked in: x_tables autofs4
  CPU: 2 PID: 1 Comm: systemd Not tainted 4.16.0-rc6-gcc_ubuntu_le-g99fec39e #1
  ...
  NIP check_version.isra.22+0x118/0x170
  Call Trace:
    __ksymtab_xt_unregister_table+0x58/0xfffffffffffffcb8 [x_tables] (unreliable)
    resolve_symbol+0xb4/0x150
    load_module+0x10e8/0x29a0
    SyS_finit_module+0x110/0x140
    system_call+0x58/0x6c

This happens because since commit 71810db2 ("modversions: treat
symbol CRCs as 32 bit quantities"), a relocatable kernel encodes and
handles symbol CRCs differently from a non-relocatable kernel.

Although it's possible we could try and detect this situation and
handle it, it's much more robust to simply make the state of
CONFIG_RELOCATABLE part of the module vermagic.

Fixes: 71810db2 ("modversions: treat symbol CRCs as 32 bit quantities")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Pull powerpc updates from Michael Ellerman:
 "Notable changes:

   - Support for 4PB user address space on 64-bit, opt-in via mmap().

   - Removal of POWER4 support, which was accidentally broken in 2016
     and no one noticed, and blocked use of some modern instructions.

   - Workarounds so that the hypervisor can enable Transactional Memory
     on Power9.

   - A series to disable the DAWR (Data Address Watchpoint Register) on
     Power9.

   - More information displayed in the meltdown/spectre_v1/v2 sysfs
     files.

   - A vpermxor (Power8 Altivec) implementation for the raid6 Q
     Syndrome.

   - A big series to make the allocation of our pacas (per cpu area),
     kernel page tables, and per-cpu stacks NUMA aware when using the
     Radix MMU on Power9.

  And as usual many fixes, reworks and cleanups.

  Thanks to: Aaro Koskinen, Alexandre Belloni, Alexey Kardashevskiy,
  Alistair Popple, Andy Shevchenko, Aneesh Kumar K.V, Anshuman Khandual,
  Balbir Singh, Benjamin Herrenschmidt, Christophe Leroy, Christophe
  Lombard, Cyril Bur, Daniel Axtens, Dave Young, Finn Thain, Frederic
  Barrat, Gustavo Romero, Horia Geantă, Jonathan Neuschäfer, Kees Cook,
  Larry Finger, Laurent Dufour, Laurent Vivier, Logan Gunthorpe,
  Madhavan Srinivasan, Mark Greer, Mark Hairgrove, Markus Elfring,
  Mathieu Malaterre, Matt Brown, Matt Evans, Mauricio Faria de Oliveira,
  Michael Neuling, Naveen N. Rao, Nicholas Piggin, Paul Mackerras,
  Philippe Bergheaud, Ram Pai, Rob Herring, Sam Bobroff, Segher
  Boessenkool, Simon Guo, Simon Horman, Stewart Smith, Sukadev
  Bhattiprolu, Suraj Jitindar Singh, Thiago Jung Bauermann, Vaibhav
  Jain, Vaidyanathan Srinivasan, Vasant Hegde, Wei Yongjun"

* tag 'powerpc-4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (207 commits)
  powerpc/64s/idle: Fix restore of AMOR on POWER9 after deep sleep
  powerpc/64s: Fix POWER9 DD2.2 and above in cputable features
  powerpc/64s: Fix pkey support in dt_cpu_ftrs, add CPU_FTR_PKEY bit
  powerpc/64s: Fix dt_cpu_ftrs to have restore_cpu clear unwanted LPCR bits
  Revert "powerpc/64s/idle: POWER9 ESL=0 stop avoid save/restore overhead"
  powerpc: iomap.c: introduce io{read|write}64_{lo_hi|hi_lo}
  powerpc: io.h: move iomap.h include so that it can use readq/writeq defs
  cxl: Fix possible deadlock when processing page faults from cxllib
  powerpc/hw_breakpoint: Only disable hw breakpoint if cpu supports it
  powerpc/mm/radix: Update command line parsing for disable_radix
  powerpc/mm/radix: Parse disable_radix commandline correctly.
  powerpc/mm/hugetlb: initialize the pagetable cache correctly for hugetlb
  powerpc/mm/radix: Update pte fragment count from 16 to 256 on radix
  powerpc/mm/keys: Update documentation and remove unnecessary check
  powerpc/64s/idle: POWER9 ESL=0 stop avoid save/restore overhead
  powerpc/64s/idle: Consolidate power9_offline_stop()/power9_idle_stop()
  powerpc/powernv: Always stop secondaries before reboot/shutdown
  powerpc: hard disable irqs in smp_send_stop loop
  powerpc: use NMI IPI for smp_send_stop
  powerpc/powernv: Fix SMT4 forcing idle code
  ...

Pull leaking-addresses updates from Tobin Harding:
 "This set represents improvements to the scripts/leaking_addresses.pl
  script.

  The major improvement is that with this set applied the script
  actually runs in a reasonable amount of time (less than a minute on a
  standard stock Ubuntu user desktop). Also, we have a second maintainer
  now and a tree hosted on kernel.org

  We do a few code clean ups. We fix the command help output. Handling
  of the vsyscall address range is fixed to check the whole range
  instead of just the start/end addresses. We add support for 5 page
  table levels (suggested on LKML). We use a system command to get the
  machine architecture instead of using Perl. Calling this command for
  every regex comparison is what previously choked the script, caching
  the result of this call gave the major speed improvement. We add
  support for scanning 32-bit kernels using the user/kernel memory
  split. Path skipping code refactored and simplified (meaning easier
  script configuration). We remove version numbering. We add a variable
  name to improve readability of a regex and finally we check filenames
  for leaking addresses.

  Currently script scans /proc/PID for all PID. With this set applied we
  only scan for PID==1. It was observed that on an idle system files
  under /proc/PID are predominantly the same for all processes. Also it
  was noted that the script does not scan _all_ the kernel since it only
  scans active processes. Scanning only for PID==1 makes explicit the
  inherent flaw in the script that the scan is only partial and also
  speeds things up"

* tag 'leaks-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tobin/leaks:
  MAINTAINERS: Update LEAKING_ADDRESSES
  leaking_addresses: check if file name contains address
  leaking_addresses: explicitly name variable used in regex
  leaking_addresses: remove version number
  leaking_addresses: skip '/proc/1/syscall'
  leaking_addresses: skip all /proc/PID except /proc/1
  leaking_addresses: cache architecture name
  leaking_addresses: simplify path skipping
  leaking_addresses: do not parse binary files
  leaking_addresses: add 32-bit support
  leaking_addresses: add is_arch() wrapper subroutine
  leaking_addresses: use system command to get arch
  leaking_addresses: add support for 5 page table levels
  leaking_addresses: add support for kernel config file
  leaking_addresses: add range check for vsyscall memory
  leaking_addresses: indent dependant options
  leaking_addresses: remove command examples
  leaking_addresses: remove mention of kptr_restrict
  leaking_addresses: fix typo function not called

Merge tag 'linux-kselftest-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull kselftest update from Shuah Khan:
 "This Kselftest update for 4.17-rc1 consists of:

   - Test build error fixes

   - Fixes to prevent intel_pstate from building on non-x86 systems.

   - New test for ion with vgem driver.

   - Change to print the test name to /dev/kmsg to add context to kernel
     failures if any uncovered from running the test.

   - Kselftest framework enhancements to add KSFT_TAP_LEVEL environment
     variable to prevent nested TAP headers being printed in the
     Kselftest output.

     Nested TAP13 headers could cause problems for some parsers. This
     change suppresses the nested headers from test programs and test
     shell scripts with changes to framework and Makefiles without
     changing the tests"

* tag 'linux-kselftest-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  selftests/intel_pstate: Fix build rule for x86
  selftests: Print the test we're running to /dev/kmsg
  selftests/seccomp: Allow get_metadata to XFAIL
  selftests/android/ion: Makefile: fix build error
  selftests: futex Makefile add top level TAP header echo to RUN_TESTS
  selftests: Makefile set KSFT_TAP_LEVEL to prevent nested TAP headers
  selftests: lib.mk set KSFT_TAP_LEVEL to prevent nested TAP headers
  selftests: kselftest framework: add handling for TAP header level
  selftests: ion: Add simple test with the vgem driver
  selftests: ion: Remove some prints

Pull general security layer updates from James Morris:

 - Convert security hooks from list to hlist, a nice cleanup, saving
   about 50% of space, from Sargun Dhillon.

 - Only pass the cred, not the secid, to kill_pid_info_as_cred and
   security_task_kill (as the secid can be determined from the cred),
   from Stephen Smalley.

 - Close a potential race in kernel_read_file(), by making the file
   unwritable before calling the LSM check (vs after), from Kees Cook.

* 'next-general' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  security: convert security hooks to use hlist
  exec: Set file unwritable before LSM check
  usb, signal, security: only pass the cred, not the secid, to kill_pid_info_as_cred and security_task_kill

Merge tag 'fscache-next-20180406' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs

Pull fscache updates from David Howells:
 "Three patches that fix some of AFS's usage of fscache:

   (1) Need to invalidate the cache if a foreign data change is detected
       on the server.

   (2) Move the vnode ID uniquifier (equivalent to i_generation) from
       the auxiliary data to the index key to prevent a race between
       file delete and a subsequent file create seeing the same index
       key.

   (3) Need to retire cookies that correspond to files that we think got
       deleted on the server.

  Four patches to fix some things in fscache and cachefiles:

   (4) Fix a couple of checker warnings.

   (5) Correctly indicate to the end-of-operation callback whether an
       operation completed or was cancelled.

   (6) Add a check for multiple cookie relinquishment.

   (7) Fix a path through the asynchronous write that doesn't wake up a
       waiter for a page if the cache decides not to write that page,
       but discards it instead.

  A couple of patches to add tracepoints to fscache and cachefiles:

   (8) Add tracepoints for cookie operators, object state machine
       execution, cachefiles object management and cachefiles VFS
       operations.

   (9) Add tracepoints for fscache operation management and page
       wrangling.

  And then three development patches:

  (10) Attach the index key and auxiliary data to the cookie, pass this
       information through various fscache-netfs API functions and get
       rid of the callbacks to the netfs to get it.

       This means that the cache can get at this information, even if
       the netfs goes away. It also means that the cache can be lazy in
       updating the coherency data.

  (11) Pass the object data size through various fscache-netfs API
       rather than calling back to the netfs for it, and store the value
       in the object.

       This makes it easier to correctly resize the object, as the size
       is updated on writes to the cache, rather than calling back out
       to the netfs.

  (12) Maintain a catalogue of allocated cookies. This makes it possible
       to catch cookie collision up front rather than down in the bowels
       of the cache being run from a service thread from the object
       state machine.

       This will also make it possible in the future to reconnect to a
       cookie that's not gone dead yet because it's waiting for
       finalisation of the storage and also make it possible to bring
       cookies online if the cache is added after the cookie has been
       obtained"

* tag 'fscache-next-20180406' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
  fscache: Maintain a catalogue of allocated cookies
  fscache: Pass object size in rather than calling back for it
  fscache: Attach the index key and aux data to the cookie
  fscache: Add more tracepoints
  fscache: Add tracepoints
  fscache: Fix hanging wait on page discarded by writeback
  fscache: Detect multiple relinquishment of a cookie
  fscache: Pass the correct cancelled indications to fscache_op_complete()
  fscache, cachefiles: Fix checker warnings
  afs: Be more aggressive in retiring cached vnodes
  afs: Use the vnode ID uniquifier in the cache key not the aux data
  afs: Invalidate cache on server data change

Pull VFIO updates from Alex Williamson:

 - Adopt iommu_unmap_fast() interface to type1 backend
   (Suravee Suthikulpanit)

 - mdev sample driver fixup (Shunyong Yang)

 - More efficient PFN mapping handling in type1 backend
   (Jason Cai)

 - VFIO device ioeventfd interface (Alex Williamson)

 - Tag new vfio-platform sub-maintainer (Alex Williamson)

* tag 'vfio-v4.17-rc1' of git://github.com/awilliam/linux-vfio:
  MAINTAINERS: vfio/platform: Update sub-maintainer
  vfio/pci: Add ioeventfd support
  vfio/pci: Use endian neutral helpers
  vfio/pci: Pull BAR mapping setup from read-write path
  vfio/type1: Improve memory pinning process for raw PFN mapping
  vfio-mdev/samples: change RDI interrupt condition
  vfio/type1: Adopt fast IOTLB flush interface when unmap IOVAs

Pull fw_cfg, vhost updates from Michael Tsirkin:
 "This cleans up the qemu fw cfg device driver.

  On top of this, vmcore is dumped there on crash to help debugging
  with kASLR enabled.

  Also included are some fixes in vhost"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  vhost: add vsock compat ioctl
  vhost: fix vhost ioctl signature to build with clang
  fw_cfg: write vmcoreinfo details
  crash: export paddr_vmcoreinfo_note()
  fw_cfg: add DMA register
  fw_cfg: add a public uapi header
  fw_cfg: handle fw_cfg_read_blob() error
  fw_cfg: remove inline from fw_cfg_read_blob()
  fw_cfg: fix sparse warnings around FW_CFG_FILE_DIR read
  fw_cfg: fix sparse warning reading FW_CFG_ID
  fw_cfg: fix sparse warnings with fw_cfg_file
  fw_cfg: fix sparse warnings in fw_cfg_sel_endianness()
  ptr_ring: fix build

Pull PCI updates from Bjorn Helgaas:

 - move pci_uevent_ers() out of pci.h (Michael Ellerman)

 - skip ASPM common clock warning if BIOS already configured it (Sinan
   Kaya)

 - fix ASPM Coverity warning about threshold_ns (Gustavo A. R. Silva)

 - remove last user of pci_get_bus_and_slot() and the function itself
   (Sinan Kaya)

 - add decoding for 16 GT/s link speed (Jay Fang)

 - add interfaces to get max link speed and width (Tal Gilboa)

 - add pcie_bandwidth_capable() to compute max supported link bandwidth
   (Tal Gilboa)

 - add pcie_bandwidth_available() to compute bandwidth available to
   device (Tal Gilboa)

 - add pcie_print_link_status() to log link speed and whether it's
   limited (Tal Gilboa)

 - use PCI core interfaces to report when device performance may be
   limited by its slot instead of doing it in each driver (Tal Gilboa)

 - fix possible cpqphp NULL pointer dereference (Shawn Lin)

 - rescan more of the hierarchy on ACPI hotplug to fix Thunderbolt/xHCI
   hotplug (Mika Westerberg)

 - add support for PCI I/O port space that's neither directly accessible
   via CPU in/out instructions nor directly mapped into CPU physical
   memory space. This is fairly intrusive and includes minor changes to
   interfaces used for I/O space on most platforms (Zhichang Yuan, John
   Garry)

 - add support for HiSilicon Hip06/Hip07 LPC I/O space (Zhichang Yuan,
   John Garry)

 - use PCI_EXP_DEVCTL2_COMP_TIMEOUT in rapidio/tsi721 (Bjorn Helgaas)

 - remove possible NULL pointer dereference in of_pci_bus_find_domain_nr()
   (Shawn Lin)

 - report quirk timings with dev_info (Bjorn Helgaas)

 - report quirks that take longer than 10ms (Bjorn Helgaas)

 - add and use Altera Vendor ID (Johannes Thumshirn)

 - tidy Makefiles and comments (Bjorn Helgaas)

 - don't set up INTx if MSI or MSI-X is enabled to align cris, frv,
   ia64, and mn10300 with x86 (Bjorn Helgaas)

 - move pcieport_if.h to drivers/pci/pcie/ to encapsulate it (Frederick
   Lawler)

 - merge pcieport_if.h into portdrv.h (Bjorn Helgaas)

 - move workaround for BIOS PME issue from portdrv to PCI core (Bjorn
   Helgaas)

 - completely disable portdrv with "pcie_ports=compat" (Bjorn Helgaas)

 - remove portdrv link order dependency (Bjorn Helgaas)

 - remove support for unused VC portdrv service (Bjorn Helgaas)

 - simplify portdrv feature permission checking (Bjorn Helgaas)

 - remove "pcie_hp=nomsi" parameter (use "pci=nomsi" instead) (Bjorn
   Helgaas)

 - remove unnecessary "pcie_ports=auto" parameter (Bjorn Helgaas)

 - use cached AER capability offset (Frederick Lawler)

 - don't enable DPC if BIOS hasn't granted AER control (Mika Westerberg)

 - rename pcie-dpc.c to dpc.c (Bjorn Helgaas)

 - use generic pci_mmap_resource_range() instead of powerpc and xtensa
   arch-specific versions (David Woodhouse)

 - support arbitrary PCI host bridge offsets on sparc (Yinghai Lu)

 - remove System and Video ROM reservations on sparc (Bjorn Helgaas)

 - probe for device reset support during enumeration instead of runtime
   (Bjorn Helgaas)

 - add ACS quirk for Ampere (née APM) root ports (Feng Kan)

 - add function 1 DMA alias quirk for Marvell 88SE9220 (Thomas
   Vincent-Cross)

 - protect device restore with device lock (Sinan Kaya)

 - handle failure of FLR gracefully (Sinan Kaya)

 - handle CRS (config retry status) after device resets (Sinan Kaya)

 - skip various config reads for SR-IOV VFs as an optimization
   (KarimAllah Ahmed)

 - consolidate VPD code in vpd.c (Bjorn Helgaas)

 - add Tegra dependency on PCI_MSI_IRQ_DOMAIN (Arnd Bergmann)

 - add DT support for R-Car r8a7743 (Biju Das)

 - fix a PCI_EJECT vs PCI_BUS_RELATIONS race condition in Hyper-V host
   bridge driver that causes a general protection fault (Dexuan Cui)

 - fix Hyper-V host bridge hang in MSI setup on 1-vCPU VMs with SR-IOV
   (Dexuan Cui)

 - fix Hyper-V host bridge hang when ejecting a VF before setting up MSI
   (Dexuan Cui)

 - make several structures static (Fengguang Wu)

 - increase number of MSI IRQs supported by Synopsys DesignWare bridges
   from 32 to 256 (Gustavo Pimentel)

 - implemented multiplexed IRQ domain API and remove obsolete MSI IRQ
   API from DesignWare drivers (Gustavo Pimentel)

 - add Tegra power management support (Manikanta Maddireddy)

 - add Tegra loadable module support (Manikanta Maddireddy)

 - handle 64-bit BARs correctly in endpoint support (Niklas Cassel)

 - support optional regulator for HiSilicon STB (Shawn Guo)

 - use regulator bulk API for Qualcomm apq8064 (Srinivas Kandagatla)

 - support power supplies for Qualcomm msm8996 (Srinivas Kandagatla)

* tag 'pci-v4.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (123 commits)
  MAINTAINERS: Add John Garry as maintainer for HiSilicon LPC driver
  HISI LPC: Add ACPI support
  ACPI / scan: Do not enumerate Indirect IO host children
  ACPI / scan: Rename acpi_is_serial_bus_slave() for more general use
  HISI LPC: Support the LPC host on Hip06/Hip07 with DT bindings
  of: Add missing I/O range exception for indirect-IO devices
  PCI: Apply the new generic I/O management on PCI IO hosts
  PCI: Add fwnode handler as input param of pci_register_io_range()
  PCI: Remove __weak tag from pci_register_io_range()
  MAINTAINERS: Add missing /drivers/pci/cadence directory entry
  fm10k: Report PCIe link properties with pcie_print_link_status()
  net/mlx5e: Use pcie_bandwidth_available() to compute bandwidth
  net/mlx5: Report PCIe link properties with pcie_print_link_status()
  net/mlx4_core: Report PCIe link properties with pcie_print_link_status()
  PCI: Add pcie_print_link_status() to log link speed and whether it's limited
  PCI: Add pcie_bandwidth_available() to compute bandwidth available to device
  misc: pci_endpoint_test: Handle 64-bit BARs properly
  PCI: designware-ep: Make dw_pcie_ep_reset_bar() handle 64-bit BARs properly
  PCI: endpoint: Make sure that BAR_5 does not have 64-bit flag set when clearing
  PCI: endpoint: Make epc->ops->clear_bar()/pci_epc_clear_bar() take struct *epf_bar
  ...

Pull rdma updates from Jason Gunthorpe:
 "Doug and I are at a conference next week so if another PR is sent I
  expect it to only be bug fixes. Parav noted yesterday that there are
  some fringe case behavior changes in his work that he would like to
  fix, and I see that Intel has a number of rc looking patches for HFI1
  they posted yesterday.

  Parav is again the biggest contributor by patch count with his ongoing
  work to enable container support in the RDMA stack, followed by Leon
  doing syzkaller inspired cleanups, though most of the actual fixing
  went to RC.

  There is one uncomfortable series here fixing the user ABI to actually
  work as intended in 32 bit mode. There are lots of notes in the commit
  messages, but the basic summary is we don't think there is an actual
  32 bit kernel user of drivers/infiniband for several good reasons.

  However we are seeing people want to use a 32 bit user space with 64
  bit kernel, which didn't completely work today. So in fixing it we
  required a 32 bit rxe user to upgrade their userspace. rxe users are
  still already quite rare and we think a 32 bit one is non-existing.

   - Fix RDMA uapi headers to actually compile in userspace and be more
     complete

   - Three shared with netdev pull requests from Mellanox:

      * 7 patches, mostly to net with 1 IB related one at the back).
        This series addresses an IRQ performance issue (patch 1),
        cleanups related to the fix for the IRQ performance problem
        (patches 2-6), and then extends the fragmented completion queue
        support that already exists in the net side of the driver to the
        ib side of the driver (patch 7).

      * Mostly IB, with 5 patches to net that are needed to support the
        remaining 10 patches to the IB subsystem. This series extends
        the current 'representor' framework when the mlx5 driver is in
        switchdev mode from being a netdev only construct to being a
        netdev/IB dev construct. The IB dev is limited to raw Eth queue
        pairs only, but by having an IB dev of this type attached to the
        representor for a switchdev port, it enables DPDK to work on the
        switchdev device.

      * All net related, but needed as infrastructure for the rdma
        driver

   - Updates for the hns, i40iw, bnxt_re, cxgb3, cxgb4, hns drivers

   - SRP performance updates

   - IB uverbs write path cleanup patch series from Leon

   - Add RDMA_CM support to ib_srpt. This is disabled by default. Users
     need to set the port for ib_srpt to listen on in configfs in order
     for it to be enabled
     (/sys/kernel/config/target/srpt/discovery_auth/rdma_cm_port)

   - TSO and Scatter FCS support in mlx4

   - Refactor of modify_qp routine to resolve problems seen while
     working on new code that is forthcoming

   - More refactoring and updates of RDMA CM for containers support from
     Parav

   - mlx5 'fine grained packet pacing', 'ipsec offload' and 'device
     memory' user API features

   - Infrastructure updates for the new IOCTL interface, based on
     increased usage

   - ABI compatibility bug fixes to fully support 32 bit userspace on 64
     bit kernel as was originally intended. See the commit messages for
     extensive details

   - Syzkaller bugs and code cleanups motivated by them"

* tag 'for-linus-unmerged' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (199 commits)
  IB/rxe: Fix for oops in rxe_register_device on ppc64le arch
  IB/mlx5: Device memory mr registration support
  net/mlx5: Mkey creation command adjustments
  IB/mlx5: Device memory support in mlx5_ib
  net/mlx5: Query device memory capabilities
  IB/uverbs: Add device memory registration ioctl support
  IB/uverbs: Add alloc/free dm uverbs ioctl support
  IB/uverbs: Add device memory capabilities reporting
  IB/uverbs: Expose device memory capabilities to user
  RDMA/qedr: Fix wmb usage in qedr
  IB/rxe: Removed GID add/del dummy routines
  RDMA/qedr: Zero stack memory before copying to user space
  IB/mlx5: Add ability to hash by IPSEC_SPI when creating a TIR
  IB/mlx5: Add information for querying IPsec capabilities
  IB/mlx5: Add IPsec support for egress and ingress
  {net,IB}/mlx5: Add ipsec helper
  IB/mlx5: Add modify_flow_action_esp verb
  IB/mlx5: Add implementation for create and destroy action_xfrm
  IB/uverbs: Introduce ESP steering match filter
  IB/uverbs: Add modify ESP flow_action
  ...

Pull mailbox updates from Jassi Brar:

 - New Hi3660 mailbox driver

 - Fix TEGRA Kconfig warning

 - Broadcom: use dma_pool_zalloc instead of dma_pool_alloc+memset

* tag 'mailbox-v4.17' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
  mailbox: Add support for Hi3660 mailbox
  dt-bindings: mailbox: Introduce Hi3660 controller binding
  mailbox: tegra: relax TEGRA_HSP_MBOX Kconfig dependencies
  maillbox: bcm-flexrm-mailbox: Use dma_pool_zalloc()

MAINTAINERS is out of date for leaking_addresses.pl. There is now a tree on
kernel.org for development of this script.  We have a second maintainer now,
thanks Tycho.  Development of this scripts was started on kernel-hardening
mailing list so let's keep it there.

Update maintainer details; Add mailing list, kernel.org hosted tree, and second
maintainer.
Signed-off-by: Tobin C. Harding <me@tobin.cc>

Sometimes files may be created by using output from printk.  As the scan
traverses the directory tree we should parse each path name and check if
it is leaking an address.

Add check for leaking address on each path name.
Suggested-by: Tycho Andersen <tycho@tycho.ws>
Acked-by: Tycho Andersen <tycho@tycho.ws>
Signed-off-by: Tobin C. Harding <me@tobin.cc>

Currently sub routine may_leak_address() is checking regex against Perl
special variable $_ which is _fortunately_ being set correctly in a loop
before this sub routine is called.  We already have declared a variable
to hold this value '$line' we should use it.

Use $line in regex match instead of implicit $_
Signed-off-by: Tobin C. Harding <me@tobin.cc>

We have git now, we don't need a version number.  This was originally
added because leaking_addresses.pl shamelessly (and mindlessly) copied
checkpatch.pl

Remove version number from script.
Signed-off-by: Tobin C. Harding <me@tobin.cc>

The pointers listed in /proc/1/syscall are user pointers, and negative
syscall args will show up like kernel addresses.

For example

/proc/31808/syscall: 0 0x3 0x55b107a38180 0x2000 0xffffffffffffffb0 \
0x55b107a302d0 0x55b107a38180 0x7fffa313b8e8 0x7ff098560d11

Skip parsing /proc/1/syscall
Suggested-by: Tycho Andersen <tycho@tycho.ws>
Signed-off-by: Tobin C. Harding <me@tobin.cc>

When the system is idle it is likely that most files under /proc/PID
will be identical for various processes.  Scanning _all_ the PIDs under
/proc is unnecessary and implies that we are thoroughly scanning /proc.
This is _not_ the case because there may be ways userspace can trigger
creation of /proc files that leak addresses but were not present during
a scan.  For these two reasons we should exclude all PID directories
under /proc except '1/'

Exclude all /proc/PID except /proc/1.
Signed-off-by: Tobin C. Harding <me@tobin.cc>

Currently we are repeatedly calling `uname -m`.  This is causing the
script to take a long time to run (more than 10 seconds to parse
/proc/kallsyms).  We can use Perl state variables to cache the result of
the first call to `uname -m`.  With this change in place the script
scans the whole kernel in under a minute.

Cache machine architecture in state variable.
Signed-off-by: Tobin C. Harding <me@tobin.cc>

Currently script has multiple configuration arrays.  This is confusing,
evident by the fact that a bunch of the entries are in the wrong place.
We can simplify the code by just having a single array for absolute
paths to skip and a single array for file names to skip wherever they
appear in the scanned directory tree.  There are also currently multiple
subroutines to handle the different arrays, we can reduce these to a
single subroutine also.

Simplify the path skipping code.
Signed-off-by: Tobin C. Harding <me@tobin.cc>

Currently script parses binary files.  Since we are scanning for
readable kernel addresses there is no need to parse binary files.  We
can use Perl to check if file is binary and skip parsing it if so.

Do not parse binary files.
Signed-off-by: Tobin C. Harding <me@tobin.cc>

Currently script only supports x86_64 and ppc64.  It would be nice to be
able to scan 32-bit machines also.  We can add support for 32-bit
architectures by modifying how we check for false positives, taking
advantage of the page offset used by the kernel, and using the correct
regular expression.

Support for 32-bit machines is enabled by the observation that the kernel
addresses on 32-bit machines are larger [in value] than the page offset.
We can use this to filter false positives when scanning the kernel for
leaking addresses.

Programmatic determination of the running architecture is not
immediately obvious (current 32-bit machines return various strings from
`uname -m`).  We therefore provide a flag to enable scanning of 32-bit
kernels.  Also we can check the kernel config file for the offset and if
not found default to 0xc0000000.  A command line option to parse in the
page offset is also provided.  We do automatically detect architecture
if running on ix86.

Add support for 32-bit kernels.  Add a command line option for page
offset.
Suggested-by: Kaiwan N Billimoria <kaiwan.billimoria@gmail.com>
Signed-off-by: Tobin C. Harding <me@tobin.cc>

Currently there is duplicate code when checking the architecture type.
We can remove the duplication by implementing a wrapper function
is_arch().

Implement and use wrapper function is_arch().
Signed-off-by: Tobin C. Harding <me@tobin.cc>

Currently script uses Perl to get the machine architecture. This can be
erroneous since Perl uses the architecture of the machine that Perl was
compiled on not the architecture of the running machine. We should use
the systems `uname` command instead.

Use `uname -m` instead of Perl to get the machine architecture.
Signed-off-by: Tobin C. Harding <me@tobin.cc>

Currently script only supports 4 page table levels because of the way
the kernel address regular expression is crafted. We can do better than
this. Using previously added support for kernel configuration options we
can get the number of page table levels defined by
CONFIG_PGTABLE_LEVELS. Using this value a correct regular expression can
be crafted. This only supports 5 page tables on x86_64.

Add support for 5 page table levels on x86_64.
Signed-off-by: Tobin C. Harding <me@tobin.cc>

Features that rely on the ability to get kernel configuration options
are ready to be implemented in script. In preparation for this we can
add support for kernel config options as a separate patch to ease
review.

Add support for locating and parsing kernel configuration file.
Signed-off-by: Tobin C. Harding <me@tobin.cc>

Currently script checks only first and last address in the vsyscall
memory range. We can do better than this. When checking for false
positives against $match, we can convert $match to a hexadecimal value
then check if it lies within the range of vsyscall addresses.

Check whole range of vsyscall addresses when checking for false
positive.
Signed-off-by: Tobin C. Harding <me@tobin.cc>

A number of the command line options to script are dependant on the
option --input-raw being set. If we indent these options it makes
explicit this dependency.

Indent options dependant on --input-raw.
Signed-off-by: Tobin C. Harding <me@tobin.cc>

Currently help output includes command examples. These were cute when we
first started development of this script but are unnecessary.

Remove command examples.
Signed-off-by: Tobin C. Harding <me@tobin.cc>

leaking_addresses.pl can be run with kptr_restrict==0 now, we don't need
the comment about setting kptr_restrict any more.

Remove comment suggesting setting kptr_restrict.
Signed-off-by: Tobin C. Harding <me@tobin.cc>

Currently code uses a check against an undefined variable because the
variable is a sub routine name and is not evaluated.

Evaluate subroutine; add parenthesis to sub routine name.
Signed-off-by: Tobin C. Harding <me@tobin.cc>

Pull SELinux updates from Paul Moore:
 "A bigger than usual pull request for SELinux, 13 patches (lucky!)
  along with a scary looking diffstat.

  Although if you look a bit closer, excluding the usual minor
  tweaks/fixes, there are really only two significant changes in this
  pull request: the addition of proper SELinux access controls for SCTP
  and the encapsulation of a lot of internal SELinux state.

  The SCTP changes are the result of a multi-month effort (maybe even a
  year or longer?) between the SELinux folks and the SCTP folks to add
  proper SELinux controls. A special thanks go to Richard for seeing
  this through and keeping the effort moving forward.

  The state encapsulation work is a bit of janitorial work that came out
  of some early work on SELinux namespacing. The question of namespacing
  is still an open one, but I believe there is some real value in the
  encapsulation work so we've split that out and are now sending that up
  to you"

* tag 'selinux-pr-20180403' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
  selinux: wrap AVC state
  selinux: wrap selinuxfs state
  selinux: fix handling of uninitialized selinux state in get_bools/classes
  selinux: Update SELinux SCTP documentation
  selinux: Fix ltp test connect-syscall failure
  selinux: rename the {is,set}_enforcing() functions
  selinux: wrap global selinux state
  selinux: fix typo in selinux_netlbl_sctp_sk_clone declaration
  selinux: Add SCTP support
  sctp: Add LSM hooks
  sctp: Add ip option support
  security: Add support for SCTP security hooks
  netlabel: If PF_INET6, check sk_buff ip header version

Pull audit updates from Paul Moore:
 "We didn't have anything to send for v4.16, but we're back with a
  little more than usual for v4.17.

  Eleven patches in total, most fall into the small fix category, but
  there are three non-trivial changes worth calling out:

   - the audit entry filter is being removed after deprecating it for
     quite a while (years of no one really using it because it turns out
     to be not very practical)

   - created our own version of "__mutex_owner()" because the locking
     folks were upset we were using theirs

   - improved our handling of kernel command line parameters to make
     them more forgiving

   - we fixed auditing of symlink operations

  Everything passes the audit-testsuite and as of a few minutes ago it
  merges well with your tree"

* tag 'audit-pr-20180403' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
  audit: add refused symlink to audit_names
  audit: remove path param from link denied function
  audit: link denied should not directly generate PATH record
  audit: make ANOM_LINK obey audit_enabled and audit_dummy_context
  audit: do not panic on invalid boot parameter
  audit: track the owner of the command mutex ourselves
  audit: return on memory error to avoid null pointer dereference
  audit: bail before bug check if audit disabled
  audit: deprecate the AUDIT_FILTER_ENTRY filter
  audit: session ID should not set arch quick field pointer
  audit: update bugtracker and source URIs

Pull pstore updates from Kees Cook:
 "This cycle was almost entirely improvements to the pstore compression
  options, noted below:

   - Add lz4hc and 842 to pstore compression options (Geliang Tang)

   - Refactor to use crypto compression API (Geliang Tang)

   - Fix up Kconfig dependencies for compression (Arnd Bergmann)

   - Allow for run-time compression selection

   - Remove stack VLA usage"

* tag 'pstore-v4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  pstore: fix crypto dependencies
  pstore: Use crypto compress API
  pstore/ram: Do not use stack VLA for parity workspace
  pstore: Select compression at runtime
  pstore: Avoid size casts for 842 compression
  pstore: Add lz4hc and 842 compression support

Merge updates from Andrew Morton:

 - a few misc things

 - ocfs2 updates

 - the v9fs maintainers have been missing for a long time. I've taken
   over v9fs patch slinging.

 - most of MM

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (116 commits)
  mm,oom_reaper: check for MMF_OOM_SKIP before complaining
  mm/ksm: fix interaction with THP
  mm/memblock.c: cast constant ULLONG_MAX to phys_addr_t
  headers: untangle kmemleak.h from mm.h
  include/linux/mmdebug.h: make VM_WARN* non-rvals
  mm/page_isolation.c: make start_isolate_page_range() fail if already isolated
  mm: change return type to vm_fault_t
  mm, oom: remove 3% bonus for CAP_SYS_ADMIN processes
  mm, page_alloc: wakeup kcompactd even if kswapd cannot free more memory
  kernel/fork.c: detect early free of a live mm
  mm: make counting of list_lru_one::nr_items lockless
  mm/swap_state.c: make bool enable_vma_readahead and swap_vma_readahead() static
  block_invalidatepage(): only release page if the full page was invalidated
  mm: kernel-doc: add missing parameter descriptions
  mm/swap.c: remove @cold parameter description for release_pages()
  mm/nommu: remove description of alloc_vm_area
  zram: drop max_zpage_size and use zs_huge_class_size()
  zsmalloc: introduce zs_huge_class_size()
  mm: fix races between swapoff and flush dcache
  fs/direct-io.c: minor cleanups in do_blockdev_direct_IO
  ...

Pull MTD updates from Boris Brezillon:
 "MTD Core:
   - Remove support for asynchronous erase (not implemented by any of
     the existing drivers anyway)
   - Remove Cyrille from the list of SPI NOR and MTD maintainers
   - Fix kernel doc headers
   - Allow users to define the partitions parsers they want to test
     through a DT property (compatible of the partitions subnode)
   - Remove the bfin-async-flash driver (the only architecture using it
     has been removed)
   - Fix pagetest test
   - Add extra checks in mtd_erase()
   - Simplify the MTD partition creation logic and get rid of
     mtd_add_device_partitions()

  MTD Drivers:
   - Add endianness information to the physmap DT binding
   - Add Eon EN29LV400A IDs to JEDEC probe logic
   - Use %*ph where appropriate

  SPI NOR Drivers:
   - Make fsl-quaspi assign different names to MTD devices connected to
     the same QSPI controller
   - Remove an unneeded driver.bus assigned in the fsl-qspi driver

  NAND Core:
   - Prepare arrival of the SPI NAND subsystem by implementing a generic
     (interface-agnostic) layer to ease manipulation of NAND devices
   - Move onenand code base to the drivers/mtd/nand/ dir
   - Rework timing mode selection
   - Provide a generic way for NAND chip drivers to flag a specific
     GET/SET FEATURE operation as supported/unsupported
   - Stop embedding ONFI/JEDEC param page in nand_chip

  NAND Drivers:
   - Rework/cleanup of the mxc driver
   - Various cleanups in the vf610 driver
   - Migrate the fsmc and vf610 to ->exec_op()
   - Get rid of the pxa driver (replaced by marvell_nand)
   - Support ->setup_data_interface() in the GPMI driver
   - Fix probe error path in several drivers
   - Remove support for unused hw_syndrome mode in sunxi_nand
   - Various minor improvements"

* tag 'mtd/for-4.17' of git://git.infradead.org/linux-mtd: (89 commits)
  dt-bindings: fsl-quadspi: Add the example of two SPI NOR
  mtd: fsl-quadspi: Distinguish the mtd device names
  mtd: nand: Fix some function description mismatches in core.c
  mtd: fsl-quadspi: Remove unneeded driver.bus assignment
  mtd: rawnand: marvell: Rename ->ecc_clk into ->core_clk
  mtd: rawnand: s3c2410: enhance the probe function error path
  mtd: rawnand: tango: fix probe function error path
  mtd: rawnand: sh_flctl: fix the probe function error path
  mtd: rawnand: omap2: fix the probe function error path
  mtd: rawnand: mxc: fix probe function error path
  mtd: rawnand: denali: fix probe function error path
  mtd: rawnand: davinci: fix probe function error path
  mtd: rawnand: cafe: fix probe function error path
  mtd: rawnand: brcmnand: fix probe function error path
  mtd: rawnand: sunxi: Stop supporting ECC_HW_SYNDROME mode
  mtd: rawnand: marvell: Fix clock resource by adding a register clock
  mtd: ftl: Use DIV_ROUND_UP()
  mtd: Fix some function description mismatches in mtdcore.c
  mtd: physmap_of: update struct map_info's swap as per map requirement
  dt-bindings: mtd-physmap: Add endianness supports
  ...

Merge tag 'for-4.17/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm

Pull device mapper updates from Mike Snitzer:

 - DM core passthrough ioctl fix to retain reference to DM table, and
   that table's block devices, while issuing the ioctl to one of those
   block devices.

 - DM core passthrough ioctl fix to _not_ override the fmode_t used to
   issue the ioctl. Overriding by using the fmode_t that the block
   device was originally open with during DM table load is a liability.

 - Add DM core support for secure erase forwarding and update the DM
   linear and DM striped targets to support them.

 - A DM core 4.16 stable fix to allow abnormal IO (e.g. discard, write
   same, write zeroes) for targets that make use of the non-splitting IO
   variant (as is done for multipath or thinp when layered directly on
   NVMe).

 - Allow DM targets to return a payload in response to a DM message that
   they are sent. This is useful for DM targets that would like to
   provide statistics data in response to DM messages.

 - Update DM bufio to support non-power-of-2 block sizes. Numerous other
   related changes prepare the DM bufio code for this support.

 - Fix DM crypt to use a bounded amount of memory across the entire
   system. This is to avoid OOM that can otherwise occur in response to
   certain pathological IO workloads (e.g. discarding a large DM crypt
   device).

 - Add a 'check_at_most_once' feature to the DM verity target to allow
   verity to be used on mobile devices that have very limited resources.

 - Fix the DM integrity target to fail early if a keyed algorithm (e.g.
   HMAC) is to be used but the key isn't set.

 - Add non-power-of-2 support to the DM unstripe target.

 - Eliminate the use of a Variable Length Array in the DM stripe target.

 - Update the DM log-writes target to record metadata (REQ_META flag).

 - DM raid fixes for its nosync status and some variable range issues.

* tag 'for-4.17/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (28 commits)
  dm: remove fmode_t argument from .prepare_ioctl hook
  dm: hold DM table for duration of ioctl rather than use blkdev_get
  dm raid: fix parse_raid_params() variable range issue
  dm verity: make verity_for_io_block static
  dm verity: add 'check_at_most_once' option to only validate hashes once
  dm bufio: don't embed a bio in the dm_buffer structure
  dm bufio: support non-power-of-two block sizes
  dm bufio: use slab cache for dm_buffer structure allocations
  dm bufio: reorder fields in dm_buffer structure
  dm bufio: relax alignment constraint on slab cache
  dm bufio: remove code that merges slab caches
  dm bufio: get rid of slab cache name allocations
  dm bufio: move dm-bufio.h to include/linux/
  dm bufio: delete outdated comment
  dm: add support for secure erase forwarding
  dm: backfill abnormal IO support to non-splitting IO submission
  dm raid: fix nosync status
  dm mpath: use DM_MAPIO_SUBMITTED instead of magic number 0 in process_queued_bios()
  dm stripe: get rid of a Variable Length Array (VLA)
  dm log writes: record metadata flag for better flags record
  ...

Pull misc vfs updates from Al Viro:
 "Assorted stuff, including Christoph's I_DIRTY patches"

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fs: move I_DIRTY_INODE to fs.h
  ubifs: fix bogus __mark_inode_dirty(I_DIRTY_SYNC | I_DIRTY_DATASYNC) call
  ntfs: fix bogus __mark_inode_dirty(I_DIRTY_SYNC | I_DIRTY_DATASYNC) call
  gfs2: fix bogus __mark_inode_dirty(I_DIRTY_SYNC | I_DIRTY_DATASYNC) calls
  fs: fold open_check_o_direct into do_dentry_open
  vfs: Replace stray non-ASCII homoglyph characters with their ASCII equivalents
  vfs: make sure struct filename->iname is word-aligned
  get rid of pointless includes of fs_struct.h
  [poll] annotate SAA6588_CMD_POLL users

* lorenzo/pci/cadence:
  MAINTAINERS: Add missing /drivers/pci/cadence directory entry