On a Chromebook I'm working on I noticed a big (~1 second) delay
during bootup where nothing was happening.  Right around this big
delay there were messages about the TPM:

[    2.311352] tpm_tis_spi spi0.0: TPM ready IRQ confirmed on attempt 2
[    3.332790] tpm_tis_spi spi0.0: Cr50 firmware version: ...

I put a few printouts in and saw that tpm_tis_spi_init() (specifically
tpm_chip_register() in that function) was taking the lion's share of
this time, though ~115 ms of the time was in cr50_print_fw_version().

Let's make a one-line change to prefer async probe for tpm_tis_spi.
There's no reason we need to block other drivers from probing while we
load.

NOTES:
* It's possible that other hardware runs through the init sequence
  faster than Cr50 and this isn't such a big problem for them.
  However, even if they are faster they are still doing _some_
  transfers over a SPI bus so this should benefit everyone even if to
  a lesser extent.
* It's possible that there are extra delays in the code that could be
  optimized out.  I didn't dig since once I enabled async probe they
  no longer impacted me.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

The tpm2_get_cc_attrs_tbl() call will result in TPM commands being issued,
which will need the use of the internal command/response buffer.  But,
we're issuing this *before* we've waited to make sure that buffer is
allocated.

This can result in intermittent failures to probe if the hypervisor / TPM
implementation doesn't respond quickly enough.  I find it fails almost
every time with an 8 vcpu guest under KVM with software emulated TPM.

To fix it, just move the tpm2_get_cc_attrs_tlb() call after the
existing code to wait for initialization, which will ensure the buffer
is allocated.

Fixes: 18b3670d ("tpm: ibmvtpm: Add support for TPM2")
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Trivial fix, the spelling of "drescription" is incorrect
in function comment.

Fix this.
Signed-off-by: Binbin Zhou <zhoubinbin@uniontech.com>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Found by smatch:
drivers/char/tpm/tpm_tis_core.c:1088 tpm_tis_core_init() warn:
 variable dereferenced before check 'chip->ops' (see line 979)

'chip->ops' is assigned in the beginning of function
in tpmm_chip_alloc->tpm_chip_alloc
and is used before first possible goto to error path.
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

During flow control we are just reading from the TPM, yet our spi_xfer
has the tx_buf and rx_buf both non-NULL which means we're requesting a
full duplex transfer.

SPI is always somewhat of a full duplex protocol anyway and in theory
the other side shouldn't really be looking at what we're sending it
during flow control, but it's still a bit ugly to be sending some
"random" data when we shouldn't.

The default tpm_tis_spi_flow_control() tries to address this by
setting 'phy->iobuf[0] = 0'.  This partially avoids the problem of
sending "random" data, but since our tx_buf and rx_buf both point to
the same place I believe there is the potential of us sending the
TPM's previous byte back to it if we hit the retry loop.

Another flow control implementation, cr50_spi_flow_control(), doesn't
address this at all.

Let's clean this up and just make the tx_buf NULL before we call
flow_control().  Not only does this ensure that we're not sending any
"random" bytes but it also possibly could make the SPI controller
behave in a slightly more optimal way.

NOTE: no actual observed problems are fixed by this patch--it's was
just made based on code inspection.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

It has been reported that some TIS based TPMs are giving unexpected
errors when using the O_NONBLOCK path of the TPM device. The problem
is that some TPMs don't like it when you get and then relinquish a
locality (as the tpm_try_get_ops()/tpm_put_ops() pair does) without
sending a command.  This currently happens all the time in the
O_NONBLOCK write path. Fix this by moving the tpm_try_get_ops()
further down the code to after the O_NONBLOCK determination is made.
This is safe because the priv->buffer_mutex still protects the priv
state being modified.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206275
Fixes: d23d1248 ("tpm: fix invalid locking in NONBLOCKING mode")
Reported-by: Mario Limonciello <Mario.Limonciello@dell.com>
Tested-by: Alex Guzman <alex@guzman.io>
Cc: stable@vger.kernel.org
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Pull hyperv fix from Wei Liu:
 "One patch from Joseph to make panic reporting contain more useful
  information"

* tag 'hyperv-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
  Drivers: hv: Change flag to write log level in panic msg to false

Pull exfat fixes from Namjae Jeon:

 - Zero out unused characters of FileName field to avoid a complaint
   from some fsck tool.

 - Fix memory leak on error paths.

 - Fix unnecessary VOL_DIRTY set when calling rmdir on non-empty
   directory.

 - Call sync_filesystem() for read-only remount (Fix generic/452 test in
   xfstests)

 - Add own fsync() to flush dirty metadata.

* tag 'exfat-for-5.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/linkinjeon/exfat:
  exfat: flush dirty metadata in fsync
  exfat: move setting VOL_DIRTY over exfat_remove_entries()
  exfat: call sync_filesystem for read-only remount
  exfat: add missing brelse() calls on error paths
  exfat: Set the unused characters of FileName field to the value 0000h

Merge tag 'fixes-v5.8-rc3-a' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security

Pull security subsystem fixes from James Morris:
 "Two simple fixes for v5.8:

   - Fix hook iteration and default value for inode_copy_up_xattr
     (KP Singh)

   - Fix the key_permission LSM hook function type (Sami Tolvanen)"

* tag 'fixes-v5.8-rc3-a' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  security: Fix hook iteration and default value for inode_copy_up_xattr
  security: fix the key_permission LSM hook function type

Merge tag 'integrity-v5.8-fix-2' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity

Pull integrity updates from Mimi Zohar:
 "Include PCRs 8 & 9 in per TPM 2.0 bank boot_aggregate calculation.

  Prior to Linux 5.8 the SHA1 "boot_aggregate" value was padded with 0's
  and extended into the other TPM 2.0 banks.

  Included in the Linux 5.8 open window, TPM 2.0 PCR bank specific
  "boot_aggregate" values (PCRs 0  - 7) are calculated and extended into the TPM banks.

  Distro releases are now shipping grub2 with TPM support, which extend
  PCRs 8 & 9. I'd like for PCRs 8 & 9 to be included in the new
  "boot_aggregate" calculations.

  For backwards compatibility, if the hash is SHA1, these new PCRs are
  not included in the boot aggregate"

* tag 'integrity-v5.8-fix-2' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity:
  ima: extend boot_aggregate with kernel measurements

Pull spi fixes from Mark Brown:
 "A batch of fixes for the Freescale DSPI driver fixing some serious
  issues with removal of active devices and one resume case, plus a few
  new PCI IDs for Intel platforms"

* tag 'spi-fix-v5.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: pxa2xx: Add support for Intel Tiger Lake PCH-H
  spi: spi-fsl-dspi: Initialize completion before possible interrupt
  spi: spi-fsl-dspi: Fix external abort on interrupt in resume or exit paths
  spi: spi-fsl-dspi: Fix lockup if device is shutdown during SPI transfer
  spi: spi-fsl-dspi: Fix lockup if device is removed during SPI transfer

Pull thermal fixes from Daniel Lezcano:

 - Fix undefined temperature if negative on the rcar_gen3 (Dien Pham)

 - Fix wrong frequency converted from power for the cpufreq cooling
   device (Finley Xiao)

 - Fix compilation warnings by making functions static in the tsens
   driver (Amit Kucheria)

 - Fix return value of sprd_thm_probe for the Spreadtrum driver
   (Tiezhu Yang)

 - Fix bank number settings on the Mediatek mt8183 (Michael Kao)

 - Fix missing of_node_put() at probe time i.MX (Anson Huang)

* tag 'thermal-v5.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
  thermal/drivers/rcar_gen3: Fix undefined temperature if negative
  thermal/drivers/cpufreq_cooling: Fix wrong frequency converted from power
  thermal/drivers/tsens: Fix compilation warnings by making functions static
  thermal/drivers/sprd: Fix return value of sprd_thm_probe()
  thermal/drivers/mediatek: Fix bank number settings on mt8183
  thermal/drivers: imx: Fix missing of_node_put() at probe time

Pull crypto fixes from Herbert Xu:
 "This fixes two race conditions, one in padata and one in af_alg"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  padata: upgrade smp_mb__after_atomic to smp_mb in padata_do_serial
  crypto: af_alg - fix use-after-free in af_alg_accept() due to bh_lock_sock()

This reverts commit e9c15bad ("fs: Do not check if there is a
fsnotify watcher on pseudo inodes"). The commit intended to eliminate
fsnotify-related overhead for pseudo inodes but it is broken in
concept. inotify can receive events of pipe files under /proc/X/fd and
chromium relies on close and open events for sandboxing. Maxim Levitsky
reported the following

  Chromium starts as a white rectangle, shows few white rectangles that
  resemble its notifications and then crashes.

  The stdout output from chromium:

  [mlevitsk@starship ~]$chromium-freeworld
  mesa: for the   --simplifycfg-sink-common option: may only occur zero or one times!
  mesa: for the   --global-isel-abort option: may only occur zero or one times!
  [3379:3379:0628/135151.440930:ERROR:browser_switcher_service.cc(238)] XXX Init()
  ../../sandbox/linux/seccomp-bpf-helpers/sigsys_handlers.cc:**CRASHING**:seccomp-bpf failure in syscall 0072
  Received signal 11 SEGV_MAPERR 0000004a9048

Crashes are not universal but even if chromium does not crash, it certainly
does not work properly. While filtering just modify and access might be
safe, the benefit is not worth the risk hence the revert.
Reported-by: Maxim Levitsky <mlevitsk@redhat.com>
Fixes: e9c15bad ("fs: Do not check if there is a fsnotify watcher on pseudo inodes")
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When the kernel panics, one page of kmsg data may be collected and sent to
Hyper-V to aid in diagnosing the failure.  The collected kmsg data typically
 contains 50 to 100 lines, each of which has a log level prefix that isn't
very useful from a diagnostic standpoint.  So tell kmsg_dump_get_buffer()
to not include the log level, enabling more information that *is* useful to
fit in the page.

Requesting in stable kernels, since many kernels running in production are
stable releases.

Cc: stable@vger.kernel.org
Signed-off-by: Joseph Salisbury <joseph.salisbury@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1593210497-114310-1-git-send-email-joseph.salisbury@microsoft.comSigned-off-by: Wei Liu <wei.liu@kernel.org>

As description for DIV_ROUND_CLOSEST in file include/linux/kernel.h.
  "Result is undefined for negative divisors if the dividend variable
   type is unsigned and for negative dividends if the divisor variable
   type is unsigned."

In current code, the FIXPT_DIV uses DIV_ROUND_CLOSEST but has not
checked sign of divisor before using. It makes undefined temperature
value in case the value is negative.

This patch fixes to satisfy DIV_ROUND_CLOSEST description
and fix bug too. Note that the variable name "reg" is not good
because it should be the same type as rcar_gen3_thermal_read().
However, it's better to rename the "reg" in a further patch as
cleanup.
Signed-off-by: Van Do <van.do.xw@renesas.com>
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
[shimoda: minor fixes, add Fixes tag]
Fixes: 564e73d2 ("thermal: rcar_gen3_thermal: Add R-Car Gen3 thermal driver")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Niklas Soderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Niklas Soderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1593085099-2057-1-git-send-email-yoshihiro.shimoda.uh@renesas.com

The function cpu_power_to_freq is used to find a frequency and set the
cooling device to consume at most the power to be converted. For example,
if the power to be converted is 80mW, and the em table is as follow.
struct em_cap_state table[] = {
	/* KHz     mW */
	{ 1008000, 36, 0 },
	{ 1200000, 49, 0 },
	{ 1296000, 59, 0 },
	{ 1416000, 72, 0 },
	{ 1512000, 86, 0 },
};
The target frequency should be 1416000KHz, not 1512000KHz.

Fixes: 349d39dc ("thermal: cpu_cooling: merge frequency and power tables")
Cc: <stable@vger.kernel.org> # v4.13+
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200619090825.32747-1-finley.xiao@rock-chips.com

After merging tsens-common.c into tsens.c, we can now mark some
functions static so they don't need any prototype declarations. This
fixes the following issue reported by lkp.

>> drivers/thermal/qcom/tsens.c:385:13: warning: no previous prototype for 'tsens_critical_irq_thread' [-Wmissing-prototypes]
385 | irqreturn_t tsens_critical_irq_thread(int irq, void *data)
|             ^~~~~~~~~~~~~~~~~~~~~~~~~
>> drivers/thermal/qcom/tsens.c:455:13: warning: no previous prototype for 'tsens_irq_thread' [-Wmissing-prototypes]
455 | irqreturn_t tsens_irq_thread(int irq, void *data)
|             ^~~~~~~~~~~~~~~~
>> drivers/thermal/qcom/tsens.c:523:5: warning: no previous prototype for 'tsens_set_trips' [-Wmissing-prototypes]
523 | int tsens_set_trips(void *_sensor, int low, int high)
|     ^~~~~~~~~~~~~~~
>> drivers/thermal/qcom/tsens.c:560:5: warning: no previous prototype for 'tsens_enable_irq' [-Wmissing-prototypes]
560 | int tsens_enable_irq(struct tsens_priv *priv)
|     ^~~~~~~~~~~~~~~~
>> drivers/thermal/qcom/tsens.c:573:6: warning: no previous prototype for 'tsens_disable_irq' [-Wmissing-prototypes]
573 | void tsens_disable_irq(struct tsens_priv *priv)
|      ^~~~~~~~~~~~~~~~~
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/6757a26876b29922929abf64b1c11fa3b3033d03.1590579709.git.amit.kucheria@linaro.org

When call function devm_platform_ioremap_resource(), we should use IS_ERR()
to check the return value and return PTR_ERR() if failed.

Fixes: 554fdbaf ("thermal: sprd: Add Spreadtrum thermal driver support")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1590371941-25430-1-git-send-email-yangtiezhu@loongson.cn

MT8183_NUM_ZONES should be set to 1
because MT8183 doesn't have multiple banks.

Fixes: a4ffe6b5 ("thermal: mediatek: add support for MT8183")
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200323121537.22697-6-michael.kao@mediatek.com

After finishing using cpu node got from of_get_cpu_node(), of_node_put()
needs to be called.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1585232945-23368-1-git-send-email-Anson.Huang@nxp.com

generic_file_fsync() exfat used could not guarantee the consistency of
a file because it has flushed not dirty metadata but only dirty data pages
for a file.

Instead of that, use exfat_file_fsync() for files and directories so that
it guarantees to commit both the metadata and data pages for a file.
Signed-off-by: Sungjong Seo <sj1557.seo@samsung.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>

Move setting VOL_DIRTY over exfat_remove_entries() to avoid unneeded
leaving VOL_DIRTY on -ENOTEMPTY.

Fixes: 5f2aa075 ("exfat: add inode operations")
Cc: stable@vger.kernel.org # v5.7
Reported-by: Tetsuhiro Kohada <kohada.t2@gmail.com>
Reviewed-by: Sungjong Seo <sj1557.seo@samsung.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>

We need to commit dirty metadata and pages to disk
before remounting exfat as read-only.

This fixes a failure in xfstests generic/452

generic/452 does the following:
cp something <exfat>/
mount -o remount,ro <exfat>

the <exfat>/something is corrupted. because while
exfat is remounted as read-only, exfat doesn't
have a chance to commit metadata and
vfs invalidates page caches in a block device.
Signed-off-by: Hyunchul Lee <hyc.lee@gmail.com>
Acked-by: Sungjong Seo <sj1557.seo@samsung.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>

If the second exfat_get_dentry() call fails then we need to release
"old_bh" before returning.  There is a similar bug in exfat_move_file().

Fixes: 5f2aa075 ("exfat: add inode operations")
Reported-by: Markus Elfring <Markus.Elfring@web.de>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>

Some fsck tool complain that padding part of the FileName field
is not set to the value 0000h. So let's maintain filesystem cleaner,
as exfat's spec. recommendation.
Signed-off-by: Hyeongseok.Kim <Hyeongseok@gmail.com>
Reviewed-by: Sungjong Seo <sj1557.seo@samsung.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>

Pull ARM OMAP fixes from Arnd Bergmann:
 "The OMAP developers are particularly active at hunting down
  regressions, so this is a separate branch with OMAP specific
  fixes for v5.8:

  As Tony explains
    "The recent display subsystem (DSS) related platform data changes
     caused display related regressions for suspend and resume. Looks
     like I only tested suspend and resume before dropping the legacy
     platform data, and forgot to test it after dropping it. Turns out
     the main issue was that we no longer have platform code calling
     pm_runtime_suspend for DSS like we did for the legacy platform data
     case, and that fix is still being discussed on the dri-devel list
     and will get merged separately. The DSS related testing exposed a
     pile other other display related issues that also need fixing
     though":

   - Fix ti-sysc optional clock handling and reset status checks for
     devices that reset automatically in idle like DSS

   - Ignore ti-sysc clockactivity bit unless separately requested to
     avoid unexpected performance issues

   - Init ti-sysc framedonetv_irq to true and disable for am4

   - Avoid duplicate DSS reset for legacy mode with dts data

   - Remove LCD timings for am4 as they cause warnings now that we're
     using generic panels

  Other OMAP changes from Tony include:

   - Fix omap_prm reset deassert as we still have drivers setting the
     pm_runtime_irq_safe() flag

   - Flush posted write for ti-sysc enable and disable

   - Fix droid4 spi related errors with spi flags

   - Fix am335x USB range and a typo for softreset

   - Fix dra7 timer nodes for clocks for IPU and DSP

   - Drop duplicate mailboxes after mismerge for dra7

   - Prevent pocketgeagle header line signal from accidentally setting
     micro-SD write protection signal by removing the default mux

   - Fix NFSroot flakeyness after resume for duover by switching the
     smsc911x gpio interrupt to back to level sensitive

   - Fix regression for omap4 clockevent source after recent system
     timer changes

   - Yet another ethernet regression fix for the "rgmii" vs "rgmii-rxid"
     phy-mode

   - One patch to convert am3/am4 DT files to use the regular sdhci-omap
     driver instead of the old hsmmc driver, this was meant for the
     merge window but got lost in the process"

* tag 'arm-omap-fixes-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (21 commits)
  ARM: dts: am5729: beaglebone-ai: fix rgmii phy-mode
  ARM: dts: Fix omap4 system timer source clocks
  ARM: dts: Fix duovero smsc interrupt for suspend
  ARM: dts: am335x-pocketbeagle: Fix mmc0 Write Protect
  Revert "bus: ti-sysc: Increase max softreset wait"
  ARM: dts: am437x-epos-evm: remove lcd timings
  ARM: dts: am437x-gp-evm: remove lcd timings
  ARM: dts: am437x-sk-evm: remove lcd timings
  ARM: dts: dra7-evm-common: Fix duplicate mailbox nodes
  ARM: dts: dra7: Fix timer nodes properly for timer_sys_ck clocks
  ARM: dts: Fix am33xx.dtsi ti,sysc-mask wrong softreset flag
  ARM: dts: Fix am33xx.dtsi USB ranges length
  bus: ti-sysc: Increase max softreset wait
  ARM: OMAP2+: Fix legacy mode dss_reset
  bus: ti-sysc: Fix uninitialized framedonetv_irq
  bus: ti-sysc: Ignore clockactivity unless specified as a quirk
  bus: ti-sysc: Use optional clocks on for enable and wait for softreset bit
  ARM: dts: omap4-droid4: Fix spi configuration and increase rate
  bus: ti-sysc: Flush posted write on enable and disable
  soc: ti: omap-prm: use atomic iopoll instead of sleeping one
  ...

Pull ARM SoC fixes from Arnd Bergmann:
 "Here are a couple of bug fixes, mostly for devicetree files

  NXP i.MX:
   - Use correct voltage on some i.MX8M board device trees to avoid
     hardware damage
   - Code fixes for a compiler warning and incorrect reference counting,
     both harmless.
   - Fix the i.MX8M SoC driver to correctly identify imx8mp
   - Fix watchdog configuration in imx6ul-kontron device tree.

  Broadcom:
   - A small regression fix for the Raspberry-Pi firmware driver
   - A Kconfig change to use the correct timer driver on Northstar
   - A DT fix for the Luxul XWC-2000 machine
   - Two more DT fixes for NSP SoCs

  STmicroelectronics STI
   - Revert one broken patch for L2 cache configuration

  ARM Versatile Express:
   - Fix a regression by reverting a broken DT cleanup

  TEE drivers:
   - MAINTAINERS: change tee mailing list"

* tag 'arm-fixes-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  Revert "ARM: sti: Implement dummy L2 cache's write_sec"
  soc: imx8m: fix build warning
  ARM: imx6: add missing put_device() call in imx6q_suspend_init()
  ARM: imx5: add missing put_device() call in imx_suspend_alloc_ocram()
  soc: imx8m: Correct i.MX8MP UID fuse offset
  ARM: dts: imx6ul-kontron: Change WDOG_ANY signal from push-pull to open-drain
  ARM: dts: imx6ul-kontron: Move watchdog from Kontron i.MX6UL/ULL board to SoM
  arm64: dts: imx8mm-beacon: Fix voltages on LDO1 and LDO2
  arm64: dts: imx8mn-ddr4-evk: correct ldo1/ldo2 voltage range
  arm64: dts: imx8mm-evk: correct ldo1/ldo2 voltage range
  ARM: dts: NSP: Correct FA2 mailbox node
  ARM: bcm2835: Fix integer overflow in rpi_firmware_print_firmware_revision()
  MAINTAINERS: change tee mailing list
  ARM: dts: NSP: Disable PL330 by default, add dma-coherent property
  ARM: bcm: Select ARM_TIMER_SP804 for ARCH_BCM_NSP
  ARM: dts: BCM5301X: Add missing memory "device_type" for Luxul XWC-2000
  arm: dts: vexpress: Move mcc node back into motherboard node

Pull timer fix from Ingo Molnar:
 "A single DocBook fix"

* tag 'timers-urgent-2020-06-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timekeeping: Fix kerneldoc system_device_crosststamp & al

Pull perf fix from Ingo Molnar:
 "A single Kbuild dependency fix"

* tag 'perf-urgent-2020-06-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/rapl: Fix RAPL config variable bug

Pull EFI fixes from Ingo Molnar:

 - Fix build regression on v4.8 and older

 - Robustness fix for TPM log parsing code

 - kobject refcount fix for the ESRT parsing code

 - Two efivarfs fixes to make it behave more like an ordinary file
   system

 - Style fixup for zero length arrays

 - Fix a regression in path separator handling in the initrd loader

 - Fix a missing prototype warning

 - Add some kerneldoc headers for newly introduced stub routines

 - Allow support for SSDT overrides via EFI variables to be disabled

 - Report CPU mode and MMU state upon entry for 32-bit ARM

 - Use the correct stack pointer alignment when entering from mixed mode

* tag 'efi-urgent-2020-06-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  efi/libstub: arm: Print CPU boot mode and MMU state at boot
  efi/libstub: arm: Omit arch specific config table matching array on arm64
  efi/x86: Setup stack correctly for efi_pe_entry
  efi: Make it possible to disable efivar_ssdt entirely
  efi/libstub: Descriptions for stub helper functions
  efi/libstub: Fix path separator regression
  efi/libstub: Fix missing-prototype warning for skip_spaces()
  efi: Replace zero-length array and use struct_size() helper
  efivarfs: Don't return -EINTR when rate-limiting reads
  efivarfs: Update inode modification time for successful writes
  efi/esrt: Fix reference count leak in esre_create_sysfs_entry.
  efi/tpm: Verify event log header before parsing
  efi/x86: Fix build with gcc 4

Pull scheduler fixes from Borislav Petkov:
 "The most anticipated fix in this pull request is probably the horrible
  build fix for the RANDSTRUCT fail that didn't make -rc2. Also included
  is the cleanup that removes those BUILD_BUG_ON()s and replaces it with
  ugly unions.

  Also included is the try_to_wake_up() race fix that was first
  triggered by Paul's RCU-torture runs, but was independently hit by
  Dave Chinner's fstest runs as well"

* tag 'sched_urgent_for_5.8_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/cfs: change initial value of runnable_avg
  smp, irq_work: Continue smp_call_function*() and irq_work*() integration
  sched/core: s/WF_ON_RQ/WQ_ON_CPU/
  sched/core: Fix ttwu() race
  sched/core: Fix PI boosting between RT and DEADLINE tasks
  sched/deadline: Initialize ->dl_boosted
  sched/core: Check cpus_mask, not cpus_ptr in __set_cpus_allowed_ptr(), to fix mask corruption
  sched/core: Fix CONFIG_GCC_PLUGIN_RANDSTRUCT build fail

Pull x86 fixes from Borislav Petkov:

 - AMD Memory bandwidth counter width fix, by Babu Moger.

 - Use the proper length type in the 32-bit truncate() syscall variant,
   by Jiri Slaby.

 - Reinit IA32_FEAT_CTL during wakeup to fix the case where after
   resume, VMXON would #GP due to VMX not being properly enabled, by
   Sean Christopherson.

 - Fix a static checker warning in the resctrl code, by Dan Carpenter.

 - Add a CR4 pinning mask for bits which cannot change after boot, by
   Kees Cook.

 - Align the start of the loop of __clear_user() to 16 bytes, to improve
   performance on AMD zen1 and zen2 microarchitectures, by Matt Fleming.

* tag 'x86_urgent_for_5.8_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/asm/64: Align start of __clear_user() loop to 16-bytes
  x86/cpu: Use pinning mask for CR4 bits needing to be 0
  x86/resctrl: Fix a NULL vs IS_ERR() static checker warning in rdt_cdp_peer_get()
  x86/cpu: Reinitialize IA32_FEAT_CTL MSR on BSP during wakeup
  syscalls: Fix offset type of ksys_ftruncate()
  x86/resctrl: Fix memory bandwidth counter width for AMD

Pull RCU-vs-KCSAN fixes from Borislav Petkov:
 "A single commit that uses "arch_" atomic operations to avoid the
  instrumentation that comes with the non-"arch_" versions.

  In preparation for that commit, it also has another commit that makes
  these "arch_" atomic operations available to generic code.

  Without these commits, KCSAN uses can see pointless errors"

* tag 'rcu_urgent_for_5.8_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  rcu: Fixup noinstr warnings
  locking/atomics: Provide the arch_atomic_ interface to generic code

Pull objtool fixes from Borislav Petkov:
 "Three fixes from Peter Zijlstra suppressing KCOV instrumentation in
  noinstr sections.

  Peter Zijlstra says:
    "Address KCOV vs noinstr. There is no function attribute to
     selectively suppress KCOV instrumentation, instead teach objtool
     to NOP out the calls in noinstr functions"

  This cures a bunch of KCOV crashes (as used by syzcaller)"

* tag 'objtool_urgent_for_5.8_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  objtool: Fix noinstr vs KCOV
  objtool: Provide elf_write_{insn,reloc}()
  objtool: Clean up elf_write() condition

Pull x86 entry fixes from Borislav Petkov:
 "This is the x86/entry urgent pile which has accumulated since the
  merge window.

  It is not the smallest but considering the almost complete entry core
  rewrite, the amount of fixes to follow is somewhat higher than usual,
  which is to be expected.

  Peter Zijlstra says:
   'These patches address a number of instrumentation issues that were
    found after the x86/entry overhaul. When combined with rcu/urgent
    and objtool/urgent, these patches make UBSAN/KASAN/KCSAN happy
    again.

    Part of making this all work is bumping the minimum GCC version for
    KASAN builds to gcc-8.3, the reason for this is that the
    __no_sanitize_address function attribute is broken in GCC releases
    before that.

    No known GCC version has a working __no_sanitize_undefined, however
    because the only noinstr violation that results from this happens
    when an UB is found, we treat it like WARN. That is, we allow it to
    violate the noinstr rules in order to get the warning out'"

* tag 'x86_entry_for_5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/entry: Fix #UD vs WARN more
  x86/entry: Increase entry_stack size to a full page
  x86/entry: Fixup bad_iret vs noinstr
  objtool: Don't consider vmlinux a C-file
  kasan: Fix required compiler version
  compiler_attributes.h: Support no_sanitize_undefined check with GCC 4
  x86/entry, bug: Comment the instrumentation_begin() usage for WARN()
  x86/entry, ubsan, objtool: Whitelist __ubsan_handle_*()
  x86/entry, cpumask: Provide non-instrumented variant of cpu_is_offline()
  compiler_types.h: Add __no_sanitize_{address,undefined} to noinstr
  kasan: Bump required compiler version
  x86, kcsan: Add __no_kcsan to noinstr
  kcsan: Remove __no_kcsan_or_inline
  x86, kcsan: Remove __no_kcsan_or_inline usage

Some performance regression on reaim benchmark have been raised with
  commit 070f5e86 ("sched/fair: Take into account runnable_avg to classify group")

The problem comes from the init value of runnable_avg which is initialized
with max value. This can be a problem if the newly forked task is finally
a short task because the group of CPUs is wrongly set to overloaded and
tasks are pulled less agressively.

Set initial value of runnable_avg equals to util_avg to reflect that there
is no waiting time so far.

Fixes: 070f5e86 ("sched/fair: Take into account runnable_avg to classify group")
Reported-by: kernel test robot <rong.a.chen@intel.com>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200624154422.29166-1-vincent.guittot@linaro.org

Instead of relying on BUG_ON() to ensure the various data structures
line up, use a bunch of horrible unions to make it all automatic.

Much of the union magic is to ensure irq_work and smp_call_function do
not (yet) see the members of their respective data structures change
name.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lkml.kernel.org/r/20200622100825.844455025@infradead.org

Use a better name for this poorly named flag, to avoid confusion...
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Mel Gorman <mgorman@suse.de>
Link: https://lkml.kernel.org/r/20200622100825.785115830@infradead.org