Based on:
NICInitRT5592MacRegisters()

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c

On vendor driver we do not initialize TX_SW_CFG{1,2}. However the same
difference is between rt2x00 and vendor driver for 5390 chip.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Based on:
RT5592_ChipSwitchChannel()

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Based on:
RT5592_ChipSwitchChannel()
RT5592_Frequency_Plan_Xtal20M[]
RT5592_Frequency_Plan_Xtal40M[]

from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add basic defines for 5592 chip. It can not be enabled until
CONFIG_RT2800USB_RT55XX configuration option will be provided in the
Kconfig.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In case the spec->channels was not specified, print warning instead
of hard crash the kernel.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800 hardware sometimes reorders tx frames when transmitting to
multiple BA enabled STAs concurrently.

For example a tx queue
	[ STA1 | STA2 | STA1 | STA2 ]
can result in the tx status reports
	[ STA1 | STA1 | STA2 | STA2 ]
when the hw decides to put the frames for STA1 in one AMPDU.

To mitigate this effect associate the currently processed tx status
to the first frame in the tx queue with a matching wcid.

This patch fixes several problems related to incorrect tx status
reporting. Furthermore the tx rate selection is much more stable when
communicating with multiple STAs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This reverts commit db36f792
since I'm going to use the data pointer that was removed in
a follow up patch.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Firmware returned VHT cap has the same format that cfg80211
expects. There is no need to parse the vht cap from the firmware
and then set it to ieee80211_sta_vht_cap. Just copying is
sufficient.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Conflicts:
	net/nfc/llcp/llcp.c

Credit distribution stats is currently implemented
only for SDIO. This fixes a crash in debugfs for
USB interface.

BUG: unable to handle kernel NULL pointer dereference at   (null)
IP: [<f91c2048>] read_file_credit_dist_stats+0x38/0x330 [ath6kl_core]
*pde = b62bd067
Oops: 0000 [#1] SMP

EIP: 0060:[<f91c2048>] EFLAGS: 00210246 CPU: 0
EIP is at read_file_credit_dist_stats+0x38/0x330 [ath6kl_core]
EAX: 00000000 EBX: e6f7a9c0 ECX: e7b148b8 EDX: 00000000
ESI: 000000c8 EDI: e7b14000 EBP: e6e09f64 ESP: e6e09f30
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Process cat (pid: 4058, ti=e6e08000 task=e50cf230 task.ti=e6e08000)
Stack:
00008000 00000000 e6e09f64 c1132d3c 00004e71 e50cf230 00008000 089e4000
e7b148b8 00000000 e6f7a9c0 00008000 089e4000 e6e09f8c c11331fc e6e09f98
00000001 e6e09f7c f91c2010 e6e09fac e6f7a9c0 089e4877 089e4000 e6e09fac

	Call Trace:
	[<c1132d3c>] ? rw_verify_area+0x6c/0x120
	[<c11331fc>] vfs_read+0x8c/0x160
	[<f91c2010>] ? read_file_war_stats+0x130/0x130 [ath6kl_core]
	[<c113330d>] sys_read+0x3d/0x70
	[<c15755b4>] syscall_call+0x7/0xb
	[<c1570000>] ? fill_powernow_table_pstate+0x127/0x127

Cc: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: Andrei Epure <epure.andrei@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Either first 3 bytes of the first received tcp segment or last one
over MTU size file can be loss due to the byte alignment problem.
Although ATH6KL_HTC_ALIGN_BYTES was defined for 'extra bytes for htc header
alignment' in the patch "Fix buffer alignment for scatter-gather
I/O"(1df94a85), there exists the bytes loss issue which means that it will be
truncated 3 bytes in the transmitted file contents if a file which has over MTU
size is transferred through TCP/IP stack.  It doesn't look like TCP/IP stack
bug of 3.5 or the latest version of kernel but the byte alignment issue.  This
patch is to use the roundup() function for the byte alignment rather than the
predefined ATH6KL_HTC_ALIGN_BYTES.

kvalo: fixed indentation
Signed-off-by: Myoungje Kim <mjei78@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Dan found a check from ath6kl_rx() which doesn't make any sense at all:

"  1327          if (status || !(skb->data + HTC_HDR_LENGTH)) {
                                ^^^^^^^^^^^^^^^^^^^^^^^^^^
skb->data is a pointer.  This pointer math is always going to be false.
Should it be testing "packet->act_len < HTC_HDR_LENGTH" or something?"

I don't know what the check really was supposed to do, but I think Dan's guess
is right. Fix it accordingly.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Dan reported that smatch found a possible issue in ath6kl_wmi_beginscan_cmd()
where we might access sc->supp_rates beyond the end. It shouldn't happen as
ar->wiphy->bands always have just the first two bands set, but add an extra
check just to be sure.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Now all log messages are sent through the tracing infrastruture as well.
Tracing point doesn't follow debug_mask module parameter, instead it sends
all debug messages, so once you enable ath6kl_log_dbg tracing point you will
get a lot of messages. Needs to be discussed if this is sensible or not.
The overhead should be small enough and we anyway include debug level as
well so it's easy to filter in user space.

I wasn't really sure what to do with ath6kl_dbg_dump() and for now decided
that it also sends the buffer to user space. But most likely in the future
ath6kl_dbg_dump() should go away in favor of using proper tracing points, but
we will see.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

All log messages are now sent through tracing interface as well if
ATH6KL_TRACING is enabled.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

After this it's cleaner to add trace calls.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Add tracing points for htc layer, just dumping the packets to user space.
I wasn't really sure what to do with the status value, it might not always
be accurate, but I included it anyway.

I skipped htc_pipe (and usb) implementation for now. Need to add those
tracepoints later.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Add a tracing point for hif irq and dump the register content to user space.
This is in hif.c as we could use the same code also with SPI but, as ath6kl
doesn't SPI and most likely never will be, this is used just by SDIO so
name the trace point as ath6kl_sdio_irq to make it easier to manage filters.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Add tracing points for sdio transfers, just dump the address, flags and the
buffer.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Add basic tracing infrastructure support to ath6kl and which can be
enabled with CONFIG_ATH6KL_TRACING.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Julien reported that ar6004 usb device fails to initialise
after host has been rebooted and power is still on for the ar6004 device. He
found out that doing a cold reset fixes the issue.

I wasn't sure what would be the best way to detect if target needs a reset so I
settled on checking a timeout from htc_wait_recv_ctrl_message().
Reported-by: Julien Massot <jmassot@aldebaran-robotics.com>
Tested-by: Julien Massot <jmassot@aldebaran-robotics.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

It was annoying to debug usb warm reboot initialisation problems as many usb
related functions just ignored errors and it wasn't obvious from the kernel
logs what was failing. Fix all that so that error messages are printed and
errors are handled properly.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Move it to init.c, make it static, remove all useless checks and force it to
always do cold reset.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Printin the  firmware capabilities during the first firmware boot makes it easier to find out what
features firmware supports.

Obligatory screenshot:

[21025.678481] ath6kl: ar6003 hw 2.1.1 sdio fw 3.2.0.144 api 3
[21025.678667] ath6kl: firmware supports: sched-scan,sta-p2pdev-duplex,rsn-cap-override
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It was another sequence I recognized in HT-PHY dump:
 phy_read(0x00c7) -> 0x0001
 phy_read(0x00c3) -> 0x0000
phy_write(0x00c3) <- 0x0002
 phy_read(0x00c3) -> 0x0000
phy_write(0x00c3) <- 0x0000
The difference to N-PHY is that it writes to 6 tables instead of a one
(after above).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Don't enable it until we have (almost?) whole TX power management
figured out. It's similar to the N-PHY, the difference is that we call a
"fix" *before* disabling power control.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It was just another similar-to-N-PHY and easy-to-track routine:
write32 0xb0601408 <- 0x00002057
 phy_read(0x0001) -> 0x0000
phy_write(0x0001) <- 0x4000
phy_write(0x0001) <- 0x0000
write32 0xb0601408 <- 0x00002055
(b43_phy_ht_force_rf_sequence was moved up unmodified)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

On N-PHY it's also done after TX power fix, so it was easy to spot.
Unfortunately the MMIO logs I have from ndsiwrapper include channels
1-12 only, so enabling code for 13 and 14 is just a N-PHY-based guess.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

On N-PHY after B43_PHY_B_TEST operation there is a call to TX power fix
function which iterates over available cores. It matches our HT-PHY code
which means it's probably also some TX fix.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

After comparing operations on reg 0xB on N and HT it seems to be the
same register with similar ops. Implement them for HT-PHY.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It you take a look at N-PHY analog switch function it touches every core
on the chipset. It seems HT-PHY does they same, it just has 3 cores
instead of 2 (which make sense since BCM4331 is 3x3). Rename AFE defines
to include core id.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Firmware got support for temperature measurement.
There are 2 temperature sensors: MAC and radio

"not available" temperature - reported by FW as 0 or ~0
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>