There's no particularly good reason TSU_POST<n> registers get accessed
circumventing sh_eth_tsu_{read|write}() -- start using those, removing
(badly named) sh_eth_tsu_get_post_reg_offset(),  while at it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Petr Machata says:

====================
bridge: FDB: Notify about removal of non-user-added entries

Device drivers may generally need to keep in sync with bridge's FDB. In
particular, for its offload of tc mirror action where the mirrored-to
device is a gretap device, mlxsw needs to listen to a number of events,
FDB events among the others. SWITCHDEV_FDB_{ADD,DEL}_TO_DEVICE would be
a natural notification in that case.

However, for removal of FDB entries added due to device activity (as
opposed to explicit addition through "bridge fdb add" or similar), there
are no notifications.

Thus in patch #1, add the "added_by_user" field to switchdev
notifications sent for FDB activity. Adapt drivers to ignore activity on
non-user-added entries, to maintain the current behavior. Specifically
in case of mlxsw, allow mlxsw_sp_span_respin() call for any and all FDB
updates.

In patch #2, change the bridge driver to actually emit notifications for
these FDB entries. Take care not to send notification for bridge
updates that itself originate in SWITCHDEV_FDB_*_TO_BRIDGE events.

Changes from v1 to v2:
- Instead of introducing a new variant of fdb_delete(), add a new
  parameter to the existing function.
- Name the parameter swdev_notify, not notify.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Do not automatically bail out on sending notifications about activity on
non-user-added FDB entries. Instead, notify about this activity except
for cases where the activity itself originates in a notification, to
avoid sending duplicate notifications.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The following patch enables sending notifications also for events on FDB
entries that weren't added by the user. Give the drivers the information
necessary to distinguish between the two origins of FDB entries.

To maintain the current behavior, have switchdev-implementing drivers
bail out on notifications about non-user-added FDB entries. In case of
mlxsw driver, allow a call to mlxsw_sp_span_respin() so that SPAN over
bridge catches up with the changed FDB.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Introduce support for CQEv1/2

Jiri says:

Current SwitchX2 and Spectrum FWs support CQEv0 and that is what we
implement in mlxsw. Spectrum FW also supports CQE v1 and v2.
However, Spectrum-2 won't support CQEv0. Prepare for it and setup the
CQE versions to use according to what is queried from FW.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Check number of CQEs for CQE version 2 reported by QUERY_AQ_CAP command.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use previously added resources to query FW support for multiple versions
of CQEs. Use the biggest version supported. For SDQs, it has no sense to
use version 2 as it does not introduce any new features, but it is
twice the size of CQE version 1.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce definitions of fields in CQE version 1 and 2. Also, introduce
common helpers that would call appropriate version-specific helpers
according to the version enum passed.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add resources that FW uses to report supported CQE versions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While handling netdevice events, br_device_event() sometimes uses
br_stp_(disable|enable)_port which unconditionally send a notification,
but then a second notification for the same event is sent at the end of
the br_device_event() function. To avoid sending duplicate notifications
in such cases, check if one has already been sent (i.e.
br_stp_enable/disable_port have been called).
The patch is based on a change by Satish Ashok.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Petr Machata says:

====================
selftests: forwarding: Updates to sysctl handling

Some selftests need to adjust sysctl settings. In order to be neutral to
the system that the test is run on, it is a good practice to change back
to the original setting after the test ends. That involves some
boilerplate that can be abstracted away.

In patch #1, introduce two functions, sysctl_set() and sysctl_restore().
The former stores the current value of a given setting, and sets a new
value. The latter restores the setting to the previously-stored value.

In patch #2, use these wrappers in a number of tests.

Additionally in patch #3, fix a problem in mirror_gre_nh.sh, which
neglected to set a sysctl that's crucial for the test to work.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The test fails to work if reverse-path filtering is in effect on the
mirrored-to host interface, or for all interfaces.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of hand-managing the sysctl set and restore, use the wrappers
sysctl_set() and sysctl_restore() to do the bookkeeping automatically.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add two helper functions: sysctl_set() to change the value of a given
sysctl setting, and sysctl_restore() to change it back to what it was.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
selftests: forwarding: Two enhancements

First patch increases the maximum deviation in the multipath tests which
proved to be too low in some cases.

Second patch allows user to run only specific tests from each file using
the TESTS environment variable. This granularity is needed in setups
where not all the tests can pass.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to commit a511858c ("selftests: fib_tests: Allow user to run
a specific test"), allow user to run only a subset of the tests using
the TESTS environment variable.

This is useful when not all the tests can pass on a given system.

Example:
# export TESTS="ping_ipv4 ping_ipv6"
# ./bridge_vlan_aware.sh
TEST: ping					[PASS]
TEST: ping6					[PASS]
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We sometimes observe failures in the test due to too large discrepancy
between the measured and expected ratios. For example:

TEST: ECMP                                                          [FAIL]
        Too large discrepancy between expected and measured ratios
        INFO: Expected ratio 1.00 Measured ratio 1.11

Fix this by allowing an up to 15% deviation between both ratios.

Another possibility is to increase the number of generated flows, but
this will prolong the execution time of the test, which is already quite
high.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change t4fw_version.h to update latest firmware version
number to 1.19.1.0.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function name is wrong in ip6gre_tnl_addr_conflict() comment, which
use ip6_tnl_addr_conflict instead of ip6gre_tnl_addr_conflict.
Signed-off-by: Sun Lianwen <sunlw.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Craig Dillabaugh says:

====================
Update csum tc action for batch operation.

This patchset includes two patches the first updating act_csum.c
to include the get_fill_size routine required for batch operation, and
the second including updated TDC tests for the feature.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Craig Dillabaugh <cdillaba@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Craig Dillabaugh <cdillaba@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
r8169: series with further improvements

I thought I'm more or less done with the basic refactoring. But again
I stumbled across things that can be improved / simplified.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is basically the same as 6e74d174 ("r8152: replace
get_protocol with vlan_get_protocol"). Use vlan_get_protocol
instead of duplicating the functionality.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Interpreting a member of an u16 array as u32 may result in a misaligned
access. Also it's not really intuitive to define a mac address variable
as array of three u16 words. Therefore use an array of six bytes that
is properly aligned for 32 bit access.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some chips have a non-zero function id, however instead of hardcoding
the id's (CSIAR_FUNC_NIC and CSIAR_FUNC_NIC2) we can get them
dynamically via PCI_FUNC(pci_dev->devfn). This way we can get rid
of the csi_ops.

In general csi is just a fallback mechanism for PCI config space
access in case no native access is supported. Therefore let's
try native access first.

I checked with Realtek regarding the functionality of config space
byte 0x070f and according to them it controls the L0s/L1
entrance latency.
Currently ASPM is disabled in general and therefore this value
isn't used. However we may introduce a whitelist for chips
where ASPM is known to work, therefore let's keep this code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Only two places are left where rtl_generic_op() is used, so we can
inline it and simplify the code a little.
This change also avoids the overhead of unlocking/locking in case
the respective operation isn't set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some longer if statements can be simplified by using switch
statements instead.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Several switch statements can be significantly simplified by using
case ranges.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After merging r810x_pll_power_down/up and r8168_pll_power_down/up we
don't need member pll_power_ops any longer and can drop it, thus
simplifying the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r810x_pll_power_down/up and r8168_pll_power_down/up have a lot in common,
so we can simplify the code by merging the former into the latter.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The functionality of 810x_phy_power_up/down is covered by the default
clause in 8168_phy_power_up/down. Therefore we don't need these
functions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RTL_GIGA_MAC_VER_23/24 are configured by rtl_hw_start_8168cp_2()
and rtl_hw_start_8168cp_3() respectively which both apply
CPCMD_QUIRK_MASK, thus clearing bit ASF.

Bit ASF isn't set at any other place in the driver, therefore this
check can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ursula Braun says:

====================
net/smc: small features 2018/04/30

here are 4 smc patches for net-next covering small new features
in different areas:
   * link health check
   * diagnostics for IPv6 smc sockets
   * ioctl
   * improvement for vlan determination

v2 changes:
   * better title
   * patch 2 - remove compile problem for disabled CONFIG_IPV6
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

An SMC link group is bound to a specific vlan_id. Its link uses
the RoCE-GIDs established for the specific vlan_id. This patch makes
sure the appropriate vlan_id is determined for stacked scenarios like
for instance a master bonding device with vlan devices enslaved.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SIOCINQ returns the amount of unread data in the RMB.
SIOCOUTQ returns the amount of unsent or unacked sent data in the send
buffer.
SIOCOUTQNSD returns the amount of data prepared for sending, but
not yet sent.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update smc_diag.c to support ipv6 addresses on the diagnosis interface.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add periodic LLC testlink support to ensure the link is still active.
The interval time is initialized using the value of
sysctl_tcp_keepalive_time.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Reject unsupported FIB configurations

Recently it became possible for listeners of the FIB notification chain
to veto operations such as addition of routes and rules.

Adjust the mlxsw driver to take advantage of it and return an error for
unsupported FIB rules and for routes configured after the abort
mechanism was triggered (due to exceeded resources for example).

v2:
* Change error code in first patch to -EOPNOTSUPP (David Ahern).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We currently do not perform accounting in the driver and thus can't
reject routes before resources are exceeded.

However, in order to make users aware of the fact that routes are no
longer offloaded we can return an error for routes configured after the
abort mechanism was triggered.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>