Merge branch 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6 into devel

Conflicts:

	arch/arm/mach-at91/gpio.c

This patch adds basic support for Dave/DENX QongEVB-LITE i.MX31-based
board. It includes support for clocks initialization, UART1, NOR-flash,
FPGA-attached NAND flash and DNET ethernet controller (inside FPGA).
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-of-by: Julien Boibessot <julien.boibessot@armadeus.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Rename driver from imx-mmc to mxc-mmc to avoid conflicts with the
mx1 mmc driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This patch adds clkdev support for i.MX31. This is done in a
similar way done previously for i.MX27
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The UART3 had a copy-paste bug. instead of claiming rxd, txd, rts and
cts pins, cts and rts were claimed twice
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

On MX31 we can't do much without mapping the AIPS1/2 register space.
Move these mappings from individual boards to plat-mxc/mm.c
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The i.MX35 basically features the same peripherals as the i.MX31 with
some differences:

- The i.MX35 has a FEC ethernet controller
- The NAND controller base addresses are different
- The i.MX35 has only 3 UARTs
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This patch adds clock support for i.MX35 SoCs. We do not support setting
of clock rates yet, but most interesting clock rates should be reported.
I couldn't test all clock rates and the datasheet contains some obvious
bugs, so expect some bugs in this code.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

We had hardcoded cpu_is_ macros for mxc architectures till now. As we
want to run the same kernel on i.MX31 and i.MX35 this patch adds cpu_is_
macros which expand to 0 or 1 if only one architecture is compiled in and
only check for the cpu type if more than one architecture is compiled
in.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This patch moves the stuff common to i.MX31 and i.MX35 to mx3x.h and the
specifics to mx31.h/mx35.h. We can build a kernel which runs on i.MX31 and
i.MX35, so always include mx31.h and mx35.h
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The var->hsync_len, var->right_margin and var->left_margin fields
should contain the real values, not the hardware dependent values.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This adds the dma (ipu_dma) and fb devices for the mx31 for which drivers now are
available.

v2: merge the ipu and fb device in the same patch as suggested by Sascha
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This enables our mx31moboard to be used on the different baseboards that
we are developping according to the application needs. There are not
many differences between the boards for now, but when other peripherals
are available for mx31 the differences are going to grow.

v2: takes Sascha's comments into account
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Make sure not to create spurious pulses on GPIOs, when configuring them as
output: first set required level, then switch direction.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

include devices.h from devices.c to avoid inconsistencies and to fix
sparse warnings
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This driver has been tested on MX27/MX31. It should work on MX1/MX1
aswell, but the actual setting of the PWM is missing so far.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

v2: As pointed out by Hans J. Koch we have to claim we can do 24bit to
    make software like X work. We are lucky on i.MX that 18bit support
    has the necessary gaps in the fields to do so.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Add framebuffer support for PCM038
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The in kernel FEC driver has recently been ported to a platform driver.
Add a platform_device for it and register it for pcm038 and mx27ads.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The i.MX31ADS supports pluggable PMU modules, including the WM835x based
Wolfson Microelectronics 1133-EV1. These boards provide power, audio,
RTC and watchdiog services to the system. This patch adds initial support
for those boards in I2C mode.

Currently support is limited by the available support for the features
of the i.MX31 in the mainline kernel.  Some further work will be needed
once other PMU modules are supported and once there is SPI support.
Many of the regulator constraints will be sharable with other PMU
boards.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>