- 12 Feb, 2016 17 commits
-
-
Pau Pajuel authored
Provide RESET GPIO for the USB PHY, the USB Host port mode and the PHY device for the controller. Also provides pin multiplexer information for USB host pins. Signed-off-by: Pau Pajuel <ppajuel@gmail.com> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Enric Balletbo i Serra authored
UART3 device is the device to be used for boot console output. Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Adam Ford authored
This patch defines the pin muxing to configure the hsusb0 through the twl4030 PMIC, because we can't always assume the bootloader will do it correctly. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Sebastian Reichel authored
The Nokia N950 and Nokia N9 have a modem attached to their first ssi port. This change adds the modem to the SSI port. Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Sebastian Reichel authored
The Nokia N950 and Nokia N9 have a modem attached to their first ssi port. This change adds all necessary information to initialize the SSI module, but does not yet add the modem information. Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Adam Ford authored
The devkit has an AT25 EEPROM on MCSPI1. Enable this with default parameters. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Adam Ford authored
Setup regulator and fix pin muxing to allow Panel to sleep and wake from sleep for some low power improvements. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Adam Ford authored
The Wireless version of the SOM uses an AT24 EEPROM to store product ID. The EEPROM is readonly. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Adam Ford authored
The Logic PD Torpedo standard kits come with a SOM populated to us an 8-bit parallel camera interface. This patch pin muxes the omap3-isp pins, sets the MT9P031 clicks, and configures the i2c2 bus to communicate with the mt9p031 on address 0x48. I have not done a lot of testing, but when modprobing mt9p031, then omap3-isp, the board responds with MT9P031 detected at address 0x48. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Kishon Vijay Abraham I authored
Add "syscon-phy-power" property and remove the deprecated "ctrl-module" property from SATA and USB PHY node. Also remove the unused control module dt nodes. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Kishon Vijay Abraham I authored
The USB2 PHY2 has a different register map compared to USB2 PHY1 to power on/off the PHY. In order to handle it, use the new compatible string "ti,dra7x-usb2-phy2" for the second instance of USB2 PHY. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Kishon Vijay Abraham I authored
Add "syscon-phy-power" property and "syscon-pcs" property which can be used to perform the control module initializations and remove the deprecated "ctrl-module" property from PCIe PHY dt nodes. Phandle to "sysclk" clock node is also added to the PCIe PHY node since some of the syscon initializations is based on system clock frequency. Since "omap_control_pcie1phy" and "omap_control_pcie2phy" devicetree nodes are no longer used, remove it. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Kishon Vijay Abraham I authored
Add new device tree node for the control module register space where PCIe registers are present. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Tony Lindgren authored
Add NAND support for dm8148-evm. Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Tony Lindgren authored
Add NAND support for j5-eco evm. Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Tony Lindgren authored
Add support for GPMC for dm814x and dra62x Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Tony Lindgren authored
The rate for auxclk is 22.59792 by default. Signed-off-by: Tony Lindgren <tony@atomide.com>
-
- 27 Jan, 2016 7 commits
-
-
Sebastian Reichel authored
Add support for the wl1271 wlan chip. As far as I can see N9 uses the same chip with the same enable and irq gpio, but they use the mmc interface instead of the spi interface. Signed-off-by: Sebastian Reichel <sre@kernel.org> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Uri Mashiach authored
Device tree modifications: - Pinmux for SPI0 and WiFi GPIOs. - SPI0 node with wlcore as a child node. Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Uri Mashiach authored
The TLV320AIC23B codec is connected to the CPU by McASP controller 1 for data and I2C0 for control. Modifications: - Enable and configure McASP controller 1. - Add TLV320AIC23B codec pinmux. - Add TLV320AIC23B codec configurations. - Use simple-audio-card as CPU to codec glue. Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Uri Mashiach authored
Touchscreen and analog digital converter configurations. Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Uri Mashiach authored
Add CAN bus pinmux. Enable D_CAN bus controllers 0 and 1 The pinmux of uart1 node contradicts the pinmux of dcan0 and dcan1 nodes. U-Boot should delete the uart1 or dcan0/1 nodes. Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Pali Rohár authored
Driver for omap3 with documentation is there since v4.4-rc1. Signed-off-by: Pali Rohár <pali.rohar@gmail.com> Acked-by: Pavel Machek <pavel@ucw.cz> Tested-by: Pavel Machek <pavel@ucw.cz> [tony@atomide.com: added thermal-sensor-cells as suggested by Roger] Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Pali Rohár authored
This patch adds adp1653 device into n900 DT structure. DT support in adp1653 driver is there since v4.2-rc1 version. Signed-off-by: Pali Rohár <pali.rohar@gmail.com> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
- 24 Jan, 2016 16 commits
-
-
Linus Torvalds authored
-
git://git.linux-mips.org/pub/scm/ralf/upstream-linusLinus Torvalds authored
Pull MIPS updates from Ralf Baechle: "This is the main pull request for MIPS for 4.5 plus some 4.4 fixes. The executive summary: - ATH79 platform improvments, use DT bindings for the ATH79 USB PHY. - Avoid useless rebuilds for zboot. - jz4780: Add NEMC, BCH and NAND device tree nodes - Initial support for the MicroChip's DT platform. As all the device drivers are missing this is still of limited use. - Some Loongson3 cleanups. - The unavoidable whitespace polishing. - Reduce clock skew when synchronizing the CPU cycle counters on CPU startup. - Add MIPS R6 fixes. - Lots of cleanups across arch/mips as fallout from KVM. - Lots of minor fixes and changes for IEEE 754-2008 support to the FPU emulator / fp-assist software. - Minor Ralink, BCM47xx and bcm963xx platform support improvments. - Support SMP on BCM63168" * 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (84 commits) MIPS: zboot: Add support for serial debug using the PROM MIPS: zboot: Avoid useless rebuilds MIPS: BMIPS: Enable ARCH_WANT_OPTIONAL_GPIOLIB MIPS: bcm63xx: nvram: Remove unused bcm63xx_nvram_get_psi_size() function MIPS: bcm963xx: Update bcm_tag field image_sequence MIPS: bcm963xx: Move extended flash address to bcm_tag header file MIPS: bcm963xx: Move Broadcom BCM963xx image tag data structure MIPS: bcm63xx: nvram: Use nvram structure definition from header file MIPS: bcm963xx: Add Broadcom BCM963xx board nvram data structure MAINTAINERS: Add KVM for MIPS entry MIPS: KVM: Add missing newline to kvm_err() MIPS: Move KVM specific opcodes into asm/inst.h MIPS: KVM: Use cacheops.h definitions MIPS: Break down cacheops.h definitions MIPS: Use EXCCODE_ constants with set_except_vector() MIPS: Update trap codes MIPS: Move Cause.ExcCode trap codes to mipsregs.h MIPS: KVM: Make kvm_mips_{init,exit}() static MIPS: KVM: Refactor added offsetof()s MIPS: KVM: Convert EXPORT_SYMBOL to _GPL ...
-
Linus Torvalds authored
Merge tag 'platform-drivers-x86-v4.5-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86 Pull x86 platform driver updates from Darren Hart: "Emergency travel prevented me from completing my final testing on this until today. Nothing here that couldn't wait until RC1 fixes, but I thought it best to get it out sooner rather than later as it does contain a build warning fix. Summary: A build warning fix, MAINTAINERS cleanup, and a new DMI quirk: ideapad-laptop: - Add Lenovo Yoga 700 to no_hw_rfkill dmi list MAINTAINERS: - Combine multiple telemetry entries intel_telemetry_debugfs: - Fix unused warnings in telemetry debugfs" * tag 'platform-drivers-x86-v4.5-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86: ideapad-laptop: Add Lenovo Yoga 700 to no_hw_rfkill dmi list MAINTAINERS: Combine multiple telemetry entries intel_telemetry_debugfs: Fix unused warnings in telemetry debugfs
-
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linuxLinus Torvalds authored
Pull thermal management updates from Zhang Rui: "The top merge commit was re-generated yesterday because two topic branches were dropped from this pull request in the last minute due to some unaddressed comments. All the other material has been in linux-next for quite a while. Specifics: - Enhance thermal core to handle unexpected device cooling states after fresh boot and system resume. From Zhang Rui and Chen Yu. - Several fixes and cleanups on Rockchip and RCAR thermal drivers. From Caesar Wang and Kuninori Morimoto. - Add Broxton support for Intel processor thermal reporting device driver. From Amy Wiles" * 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: thermal: trip_point_temp_store() calls thermal_zone_device_update() thermal: rcar: rcar_thermal_get_temp() return error if strange temp thermal: rcar: check irq possibility in rcar_thermal_irq_xxx() thermal: rcar: check every rcar_thermal_update_temp() return value thermal: rcar: move rcar_thermal_dt_ids to upside thermal: rockchip: Support the RK3399 SoCs in thermal driver thermal: rockchip: Support the RK3228 SoCs in thermal driver dt-bindings: rockchip-thermal: Support the RK3228/RK3399 SoCs compatible thermal: rockchip: fix a trivial typo Thermal: Enable Broxton SoC thermal reporting device thermal: constify pch_dev_ops structure Thermal: do thermal zone update after a cooling device registered Thermal: handle thermal zone device properly during system sleep Thermal: initialize thermal zone device correctly
-
git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fsLinus Torvalds authored
Pull 9p updates from Eric Van Hensbergen: "Sorry for the last minute pull request, there's was a change that didn't get pulled into for-next until two weeks ago and I wanted to give it some bake time. Summary: Rework and error handling fixes, primarily in the fscatch and fd transports" * tag 'for-linus-4.5-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs: fs/9p: use fscache mutex rather than spinlock 9p: trans_fd, bail out if recv fcall if missing 9p: trans_fd, read rework to use p9_parse_header net/9p: Add device name details on error
-
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-clientLinus Torvalds authored
Pull Ceph updates from Sage Weil: "The two main changes are aio support in CephFS, and a series that fixes several issues in the authentication key timeout/renewal code. On top of that are a variety of cleanups and minor bug fixes" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: libceph: remove outdated comment libceph: kill off ceph_x_ticket_handler::validity libceph: invalidate AUTH in addition to a service ticket libceph: fix authorizer invalidation, take 2 libceph: clear messenger auth_retry flag if we fault libceph: fix ceph_msg_revoke() libceph: use list_for_each_entry_safe ceph: use i_size_{read,write} to get/set i_size ceph: re-send AIO write request when getting -EOLDSNAP error ceph: Asynchronous IO support ceph: Avoid to propagate the invalid page point ceph: fix double page_unlock() in page_mkwrite() rbd: delete an unnecessary check before rbd_dev_destroy() libceph: use list_next_entry instead of list_entry_next ceph: ceph_frag_contains_value can be boolean ceph: remove unused functions in ceph_frag.h
-
git://git.samba.org/sfrench/cifs-2.6Linus Torvalds authored
Pull SMB3 fixes from Steve French: "A collection of CIFS/SMB3 fixes. It includes a couple bug fixes, a few for improved debugging of cifs.ko and some improvements to the way cifs does key generation. I do have some additional bug fixes I expect in the next week or two (to address a problem found by xfstest, and some fixes for SMB3.11 dialect, and a couple patches that just came in yesterday that I am reviewing)" * 'for-next' of git://git.samba.org/sfrench/cifs-2.6: cifs_dbg() outputs an uninitialized buffer in cifs_readdir() cifs: fix race between call_async() and reconnect() Prepare for encryption support (first part). Add decryption and encryption key generation. Thanks to Metze for helping with this. cifs: Allow using O_DIRECT with cache=loose cifs: Make echo interval tunable cifs: Check uniqueid for SMB2+ and return -ESTALE if necessary Print IP address of unresponsive server cifs: Ratelimit kernel log messages
-
Josh Boyer authored
Like the Yoga 900 models the Lenovo Yoga 700 does not have a hw rfkill switch, and trying to read the hw rfkill switch through the ideapad module causes it to always reported blocking breaking wifi. This commit adds the Lenovo Yoga 700 to the no_hw_rfkill dmi list, fixing the wifi breakage. BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1295272 Tested-by: <dinyar.rabady+spam@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org> Signed-off-by: Darren Hart <dvhart@linux.intel.com>
-
Souvik Kumar Chakravarty authored
This patch combines all the telemetry file entries in MAINTAINERS via wildcard. Signed-off-by: Souvik Kumar Chakravarty <souvik.k.chakravarty@intel.com> Signed-off-by: Darren Hart <dvhart@linux.intel.com>
-
Souvik Kumar Chakravarty authored
This patch fixes compile time warnings when CONFIG_PM_SLEEP is undefined. In this case sleep related counters are unused. Signed-off-by: Souvik Kumar Chakravarty <souvik.k.chakravarty@intel.com> Signed-off-by: Darren Hart <dvhart@linux.intel.com>
-
Christoph Lameter authored
If we detect that there is nothing to do just set the flag and do not check if it was already set before. Races really do not matter. If the flag is set by any code then the shepherd will start dealing with the situation and reenable the vmstat workers when necessary again. Since commit 0eb77e98 ("vmstat: make vmstat_updater deferrable again and shut down on idle") quiet_vmstat might update cpu_stat_off and mark a particular cpu to be handled by vmstat_shepherd. This might trigger a VM_BUG_ON in vmstat_update because the work item might have been sleeping during the idle period and see the cpu_stat_off updated after the wake up. The VM_BUG_ON is therefore misleading and no more appropriate. Moreover it doesn't really suite any protection from real bugs because vmstat_shepherd will simply reschedule the vmstat_work anytime it sees a particular cpu set or vmstat_update would do the same from the worker context directly. Even when the two would race the result wouldn't be incorrect as the counters update is fully idempotent. Reported-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Christoph Lameter <cl@linux.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Ralf Baechle authored
-
Alban Bedel authored
As most platforms implement the PROM serial interface prom_putchar() add a simple bridge to allow re-using this code for zboot. Signed-off-by: Alban Bedel <albeu@free.fr> Cc: Alex Smith <alex.smith@imgtec.com> Cc: Andrew Bresticker <abrestic@chromium.org> Cc: Wu Zhangjin <wuzhangjin@gmail.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/11811/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Alban Bedel authored
Add dummy.o to the targets list, and fill targets automatically from $(vmlinuzobjs) to avoid having to maintain two lists. When building with XZ compression copy ashldi3.c to the build directory to use a different object file for the kernel and zboot. Without this the same object file need to be build with different flags which cause a rebuild at every run. Signed-off-by: Alban Bedel <albeu@free.fr> Cc: linux-mips@linux-mips.org Cc: Alex Smith <alex.smith@imgtec.com> Cc: Wu Zhangjin <wuzhangjin@gmail.com> Cc: Andrew Bresticker <abrestic@chromium.org> Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/11810/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Florian Fainelli authored
Allow BMIPS_GENERIC supported platforms to build GPIO controller drivers. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Dragan Stancevic <dragan.stancevic@gmail.com> Cc: cernekee@gmail.com Cc: jaedon.shin@gmail.com Cc: gregory.0xf0@gmail.com Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/12019/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Simon Arlott authored
Remove bcm63xx_nvram_get_psi_size() as it now has no users. Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Kevin Cernekee <cernekee@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Jonas Gorski <jogo@openwrt.org> Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org> Cc: MIPS Mailing List <linux-mips@linux-mips.org> Cc: MTD Maling List <linux-mtd@lists.infradead.org> Patchwork: https://patchwork.linux-mips.org/patch/11836/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-