Merge tag 'iwlwifi-for-kalle-2015-01-15' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes

* one fix for rfkill while scheduled scan is running.
  Linus's system hit this issue. WiFi would be unavailable
  after this has happpened because of bad state in cfg80211.

When we have an active scheduled scan, and the RFKILL
interrupt kicks in, the stack will cancel the scheduled
scan as part of the down flow. But cancelling scheduled
scan usually implies sending a command to the firwmare
which has been killed as part of the RFKILL interrupt
handling.
Because of that, we returned an error to mac80211 when
it asked to stop the scheduled scan and didn't notify the
end of the scheduled scan. Besides a fat warning, this led
to a situation in which cfg80211 would refuse any new scan
request.

To disentangle this, fake that the scheduled scan has been
stopped without sending the command to the firwmare, return
0 after having properly let cfg80211 know that the scan
has been cancelled.

This is basically the same as:
commit 9b520d84
Author: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Date:   Tue Nov 4 15:54:11 2014 +0200

    iwlwifi: mvm: abort scan upon RFKILL

    This code existed but not for all the different FW APIs
    we support.
    Fix this.

but for the scheduled scan case.

Link: http://permalink.gmane.org/gmane.linux.kernel.wireless.general/133232Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Merge tag 'iwlwifi-for-kalle-2015-01-13' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes

* A fix for scan that fixes a firmware assertion
* A fix that improves roaming behavior. Same fix has been tested for
  a while in iwldvm. This is a bit of a work around, but the real fix
  should be in mac80211 and will come later.
* A fix for BARs that avoids a WARNING.

Other tunnels like GRE break while VxLAN offloads are enabled in Skyhawk-R. To
avoid this, we should restrict offload features on a per-packet basis in such
conditions.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Don't use uninitialized data in IPVS, from Dan Carpenter.

 2) conntrack race fixes from Pablo Neira Ayuso.

 3) Fix TX hangs with i40e, from Jesse Brandeburg.

 4) Fix budget return from poll calls in dnet and alx, from Eric
    Dumazet.

 5) Fix bugus "if (unlikely(x) < 0)" test in AF_PACKET, from Christoph
    Jaeger.

 6) Fix bug introduced by conversion to list_head in TIPC retransmit
    code, from Jon Paul Maloy.

 7) Don't use GFP_NOIO under spinlock in USB kaweth driver, from Alexey
    Khoroshilov.

 8) Fix bridge build with INET disabled, from Arnd Bergmann.

 9) Fix netlink array overrun for PROBE attributes in openvswitch, from
    Thomas Graf.

10) Don't hold spinlock across synchronize_irq() in tg3 driver, from
    Prashant Sreedharan.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
  tg3: Release tp->lock before invoking synchronize_irq()
  tg3: tg3_reset_task() needs to use rtnl_lock to synchronize
  tg3: tg3_timer() should grab tp->lock before checking for tp->irq_sync
  team: avoid possible underflow of count_pending value for notify_peers and mcast_rejoin
  openvswitch: packet messages need their own probe attribtue
  i40e: adds FCoE configure option
  cxgb4vf: Fix queue allocation for 40G adapter
  netdevice: Add missing parentheses in macro
  bridge: only provide proxy ARP when CONFIG_INET is enabled
  neighbour: fix base_reachable_time(_ms) not effective immediatly when changed
  net: fec: fix MDIO bus assignement for dual fec SoC's
  xen-netfront: use different locks for Rx and Tx stats
  drivers: net: cpsw: fix multicast flush in dual emac mode
  cxgb4vf: Initialize mdio_addr before using it
  net: Corrected the comment describing the ndo operations to reflect the actual prototype for couple of operations
  usb/kaweth: use GFP_ATOMIC under spin_lock in usb_start_wait_urb()
  MAINTAINERS: add me as ibmveth maintainer
  tipc: fix bug in broadcast retransmit code
  update ip-sysctl.txt documentation (v2)
  net/at91_ether: prepare and unprepare clock
  ...

Prashant Sreedharan says:

====================
tg3: synchronize_irq() should be called without taking locks

v2: Added Reported-by, Tested-by fields and reference to the thread that
    reported the problem

This series addresses the problem reported by Peter Hurley in mail thread
https://lkml.org/lkml/2015/1/12/1082
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

synchronize_irq() can sleep waiting, for pending IRQ handlers so driver
should release the tp->lock spin lock before invoking synchronize_irq()
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently tg3_reset_task() uses only tp->lock for synchronizing with code
paths like tg3_open() etc. But since tp->lock is released before doing
synchronize_irq(), rtnl_lock should be taken in tg3_reset_task() to
synchronize it with other code paths.
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is to avoid the race between tg3_timer() and the execution paths
which does not invoke tg3_timer_stop() and releases tp->lock before
calling synchronize_irq()
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull kvm fixes from Paolo Bonzini:
 "Two bugfixes for arm64.  I will have another pull request next week,
  but otherwise things are calm"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  arm64: KVM: Fix HCR setting for 32bit guests
  arm64: KVM: Fix TLB invalidation by IPA/VMID

This patch is fixing a race condition that may cause setting
count_pending to -1, which results in unwanted big bulk of arp messages
(in case of "notify peers").

Consider following scenario:

count_pending == 2
   CPU0                                           CPU1
					team_notify_peers_work
					  atomic_dec_and_test (dec count_pending to 1)
					  schedule_delayed_work
 team_notify_peers
   atomic_add (adding 1 to count_pending)
					team_notify_peers_work
					  atomic_dec_and_test (dec count_pending to 1)
					  schedule_delayed_work
					team_notify_peers_work
					  atomic_dec_and_test (dec count_pending to 0)
   schedule_delayed_work
					team_notify_peers_work
					  atomic_dec_and_test (dec count_pending to -1)

Fix this race by using atomic_dec_if_positive - that will prevent
count_pending running under 0.

Fixes: fc423ff0 ("team: add peer notification")
Fixes: 492b200e  ("team: add support for sending multicast rejoins")
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull s390 fixes from Martin Schwidefsky:
 "Two small performance tweaks, the plumbing for the execveat system
  call and a couple of bug fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/uprobes: fix user space PER events
  s390/bpf: Fix JMP_JGE_X (A > X) and JMP_JGT_X (A >= X)
  s390/bpf: Fix ALU_NEG (A = -A)
  s390/mm: avoid using pmd_to_page for !USE_SPLIT_PMD_PTLOCKS
  s390/timex: fix get_tod_clock_ext() inline assembly
  s390: wire up execveat syscall
  s390/kernel: use stnsm 255 instead of stosm 0
  s390/vtime: Get rid of redundant WARN_ON
  s390/zcrypt: kernel oops at insmod of the z90crypt device driver

User space is currently sending a OVS_FLOW_ATTR_PROBE for both flow
and packet messages. This leads to an out-of-bounds access in
ovs_packet_cmd_execute() because OVS_FLOW_ATTR_PROBE >
OVS_PACKET_ATTR_MAX.

Introduce a new OVS_PACKET_ATTR_PROBE with the same numeric value
as OVS_FLOW_ATTR_PROBE to grow the range of accepted packet attributes
while maintaining to be binary compatible with existing OVS binaries.

Fixes: 05da5898 ("openvswitch: Add support for OVS_FLOW_ATTR_PROBE.")
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Tracked-down-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adds FCoE config option I40E_FCOE, so that FCoE can be enabled
as needed but otherwise have it disabled by default.

This also eliminate multiple FCoE config checks, instead now just
one config check for CONFIG_I40E_FCOE.

The I40E FCoE was added with 3.17 kernel and therefore this patch
shall be applied to stable 3.17 kernel also.

CC: <stable@vger.kernel.org>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull file locking fix from Jeff Layton:
 "Just a simple bugfix for a regression that I introduced into v3.18
  with the internal lease API overhaul -- mea culpa.  Kudos to Linda and
  Neil for tracking this down and fixing it"

* tag 'locks-v3.19-1' of git://git.samba.org/jlayton/linux:
  locks: fix NULL-deref in generic_delete_lease

For example, one could conceivably call
	for_each_netdev_in_bond_rcu(condition ? bond1 : bond2, slave)
and get an unexpected result.
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull block layer fixes from Jens Axboe:
 "The major part is an update to the NVMe driver, fixing various issues
  around surprise removal and hung controllers.  Most of that is from
  Keith, and parts are simple blk-mq fixes or exports/additions of minor
  functions to aid this effort, and parts are changes directly to the
  NVMe driver.

  Apart from the above, this contains:

   - Small blk-mq change from me, killing an unused member of the
     hardware queue structure.

   - Small fix from Ming Lei, fixing up a few drivers that didn't
     properly check for ERR_PTR() returns from blk_mq_init_queue()"

* 'for-linus' of git://git.kernel.dk/linux-block:
  NVMe: Fix locking on abort handling
  NVMe: Start and stop h/w queues on reset
  NVMe: Command abort handling fixes
  NVMe: Admin queue removal handling
  NVMe: Reference count admin queue usage
  NVMe: Start all requests
  blk-mq: End unstarted requests on a dying queue
  blk-mq: Allow requests to never expire
  blk-mq: Add helper to abort requeued requests
  blk-mq: Let drivers cancel requeue_work
  blk-mq: Export if requests were started
  blk-mq: Wake tasks entering queue on dying
  blk-mq: get rid of ->cmd_size in the hardware queue
  block: fix checking return value of blk_mq_init_queue
  block: wake up waiters when a queue is marked dying
  NVMe: Fix double free irq
  blk-mq: Export freeze/unfreeze functions
  blk-mq: Exit queue on alloc failure

When IPV4 support is disabled, we cannot call arp_send from
the bridge code, which would result in a kernel link error:

net/built-in.o: In function `br_handle_frame_finish':
:(.text+0x59914): undefined reference to `arp_send'
:(.text+0x59a50): undefined reference to `arp_tbl'

This makes the newly added proxy ARP support in the bridge
code depend on the CONFIG_INET symbol and lets the compiler
optimize the code out to avoid the link error.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 95850116 ("bridge: Add support for IEEE 802.11 Proxy ARP")
Cc: Kyeyoon Park <kyeyoonp@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When setting base_reachable_time or base_reachable_time_ms on a
specific interface through sysctl or netlink, the reachable_time
value is not updated.

This means that neighbour entries will continue to be updated using the
old value until it is recomputed in neigh_period_work (which
    recomputes the value every 300*HZ).
On systems with HZ equal to 1000 for instance, it means 5mins before
the change is effective.

This patch changes this behavior by recomputing reachable_time after
each set on base_reachable_time or base_reachable_time_ms.
The new value will become effective the next time the neighbour's timer
is triggered.

Changes are made in two places: the netlink code for set and the sysctl
handling code. For sysctl, I use a proc_handler. The ipv6 network
code does provide its own handler but it already refreshes
reachable_time correctly so it's not an issue.
Any other user of neighbour which provide its own handlers must
refresh reachable_time.
Signed-off-by: Jean-Francois Remy <jeff@melix.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

On i.MX28, the MDIO bus is shared between the two FEC instances.
The driver makes sure that the second FEC uses the MDIO bus of the
first FEC. This is done conditionally if FEC_QUIRK_ENET_MAC is set.
However, in newer designs, such as Vybrid or i.MX6SX, each FEC MAC
has its own MDIO bus. Simply removing the quirk FEC_QUIRK_ENET_MAC
is not an option since other logic, triggered by this quirk, is
still needed.

Furthermore, there are board designs which use the same MDIO bus
for both PHY's even though the second bus would be available on the
SoC side. Such layout are popular since it saves pins on SoC side.
Due to the above quirk, those boards currently do work fine. The
boards in the mainline tree with such a layout are:
- Freescale Vybrid Tower with TWR-SER2 (vf610-twr.dts)
- Freescale i.MX6 SoloX SDB Board (imx6sx-sdb.dts)

This patch adds a new quirk FEC_QUIRK_SINGLE_MDIO for i.MX28, which
makes sure that the MDIO bus of the first FEC is used in any case.

However, the boards above do have a SoC with a MDIO bus for each FEC
instance. But the PHY's are not connected in a 1:1 configuration. A
proper device tree description is needed to allow the driver to
figure out where to find its PHY. This patch fixes that shortcoming
by adding a MDIO bus child node to the first FEC instance, along
with the two PHY's on that bus, and making use of the phy-handle
property to add a reference to the PHY's.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'leds-fixes-for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds

Pull LED fix from Bryan Wu.

* 'leds-fixes-for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
  leds: netxbig: fix oops at probe time

Pull WRITE_ONCE argument order change from Christian Borntraeger:
 "As discussed on LKML[1] it was agreed that WRITE_ONCE(x, val) is
  better than ASSIGN_ONCE(val, x)

  Lets change that for 3.19 as 3.19 has no user yet, but the first users
  will hit linux-next soon"

[1] http://marc.info/?l=linux-kernel&m=142081181707596

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/borntraeger/linux:
  kernel: Change ASSIGN_ONCE(val, x) to WRITE_ONCE(x, val)

In netfront the Rx and Tx path are independent and use different
locks.  The Tx lock is held with hard irqs disabled, but Rx lock is
held with only BH disabled.  Since both sides use the same stats lock,
a deadlock may occur.

  [ INFO: possible irq lock inversion dependency detected ]
  3.16.2 #16 Not tainted
  ---------------------------------------------------------
  swapper/0/0 just changed the state of lock:
   (&(&queue->tx_lock)->rlock){-.....}, at: [<c03adec8>]
  xennet_tx_interrupt+0x14/0x34
  but this lock took another, HARDIRQ-unsafe lock in the past:
   (&stat->syncp.seq#2){+.-...}
  and interrupts could create inverse lock ordering between them.
  other info that might help us debug this:
   Possible interrupt unsafe locking scenario:

         CPU0                    CPU1
         ----                    ----
    lock(&stat->syncp.seq#2);
                                 local_irq_disable();
                                 lock(&(&queue->tx_lock)->rlock);
                                 lock(&stat->syncp.seq#2);
    <Interrupt>
      lock(&(&queue->tx_lock)->rlock);

Using separate locks for the Rx and Tx stats fixes this deadlock.
Reported-by: Dmitry Piotrovsky <piotrovskydmitry@gmail.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since ALE table is a common resource for both the interfaces in Dual EMAC
mode and while bringing up the second interface in cpsw_ndo_set_rx_mode()
all the multicast entries added by the first interface is flushed out and
only second interface multicast addresses are added. Fixing this by
flushing multicast addresses based on dual EMAC port vlans which will not
affect the other emac port multicast addresses.

Fixes: d9ba8f9e (driver: net: ethernet: cpsw: dual emac interface implementation)
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a NULL pointer dereference on led_dat->mode_val. Due to
this bug, a kernel oops can be observed at probe time on the LaCie 2Big
and 5Big v2 boards:

Unable to handle kernel NULL pointer dereference at virtual address 00000008
[...]
[<c03f244c>] (netxbig_led_probe) from [<c02c8c6c>] (platform_drv_probe+0x4c/0x9c)
[<c02c8c6c>] (platform_drv_probe) from [<c02c72d0>] (driver_probe_device+0x98/0x25c)
[<c02c72d0>] (driver_probe_device) from [<c02c7520>] (__driver_attach+0x8c/0x90)
[<c02c7520>] (__driver_attach) from [<c02c5c24>] (bus_for_each_dev+0x68/0x94)
[<c02c5c24>] (bus_for_each_dev) from [<c02c6408>] (bus_add_driver+0x124/0x1dc)
[<c02c6408>] (bus_add_driver) from [<c02c7ac0>] (driver_register+0x78/0xf8)
[<c02c7ac0>] (driver_register) from [<c000888c>] (do_one_initcall+0x80/0x1cc)
[<c000888c>] (do_one_initcall) from [<c0733618>] (kernel_init_freeable+0xe4/0x1b4)
[<c0733618>] (kernel_init_freeable) from [<c058db9c>] (kernel_init+0xc/0xec)
[<c058db9c>] (kernel_init) from [<c0009850>] (ret_from_fork+0x14/0x24)
[...]

This bug was introduced by commit 588a6a99
("leds: netxbig: fix attribute-creation race").
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: <stable@vger.kernel.org> # 3.17+
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>

In commit 5ad24def ("cxgb4vf: Fix ethtool get_settings for VF driver")
mdio_addr of port_info structure was used unininitialzed. Fixing it.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Feedback has shown that WRITE_ONCE(x, val) is easier to use than
ASSIGN_ONCE(val,x).
There are no in-tree users yet, so lets change it for 3.19.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Davidlohr Bueso <dave@stgolabs.net>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>

Merge tag 'linux-kselftest-3.19-rc-5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull kselftest fixes from Shuah Khan:
 "This update contains three patches to fix one compile error, and two
  run-time bugs.  One of them fixes infinite loop on ARM"

* tag 'linux-kselftest-3.19-rc-5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  selftests/vm: fix link error for transhuge-stress test
  tools: testing: selftests: mq_perf_tests: Fix infinite loop on ARM
  selftests/exec: allow shell return code of 126

Pull xen bug fixes from David Vrabel:
 "Several critical linear p2m fixes that prevented some hosts from
  booting"

* tag 'stable/for-linus-3.19-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  x86/xen: properly retrieve NMI reason
  xen: check for zero sized area when invalidating memory
  xen: use correct type for physical addresses
  xen: correct race in alloc_p2m_pmd()
  xen: correct error for building p2m list on 32 bits
  x86/xen: avoid freeing static 'name' when kasprintf() fails
  x86/xen: add extra memory for remapped frames during setup
  x86/xen: don't count how many PFNs are identity mapped
  x86/xen: Free bootmem in free_p2m_page() during early boot
  x86/xen: Remove unnecessary BUG_ON(preemptible()) in xen_setup_timer()

net: Corrected the comment describing the ndo operations to reflect the actual prototype for couple of operations

Corrected the comment describing the ndo operations to
reflect the actual prototype for couple of operations
Signed-off-by: B Viswanath <marichika4@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull thermal management fixes from Zhang Rui:
 "Specifics:

   - Fix a problem that Intel SoC DTS thermal driver does not work when
     CONFIG_THERMAL_INT340X is not set.

   - Fix a NULL pointer dereference when processor_thermal_device driver
     is loaded on a platform without ACPI support"

* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  int340x_thermal/processor_thermal_device: return failure when
  ACPI/int340x_thermal: enumerate INT3401 for Intel SoC DTS thermal driver
  ACPI/int340x_thermal: enumerate INT340X devices even if they're not in _ART/_TRT

commit 0efaa7e8
  locks: generic_delete_lease doesn't need a file_lock at all

moves the call to fl->fl_lmops->lm_change() to a place in the
code where fl might be a non-lease lock.
When that happens, fl_lmops is NULL and an Oops ensures.

So add an extra test to restore correct functioning.
Reported-by: Linda Walsh <suse@tlinx.org>
Link: https://bugzilla.suse.com/show_bug.cgi?id=912569
Cc: stable@vger.kernel.org (v3.18)
Fixes: 0efaa7e8Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jeff Layton <jlayton@primarydata.com>

Using the native code here can't work properly, as the hypervisor would
normally have cleared the two reason bits by the time Dom0 gets to see
the NMI (if passed to it at all). There's a shared info field for this,
and there's an existing hook to use - just fit the two together. This
is particularly relevant so that NMIs intended to be handled by APEI /
GHES actually make it to the respective handler.

Note that the hook can (and should) be used irrespective of whether
being in Dom0, as accessing port 0x61 in a DomU would be even worse,
while the shared info field would just hold zero all the time. Note
further that hardware NMI handling for PVH doesn't currently work
anyway due to missing code in the hypervisor (but it is expected to
work the native rather than the PV way).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

BAR tx cmd tid was set to non qos (8). This is wrong as BAR
should be sent with the tid of the BA session.
This led to a corruption in the firmware. The visible
effect of this from the driver side is the BA notification
that comes back after the BAR. It was botched and led to the
WARNING below.

------------[ cut here ]------------
WARNING: CPU: 2 PID: 17707 at /home/tester/workspace_hostap/iwlwifi/drivers/net/wireless/iwlwifi/mvm/tx.c:976 iwl_mvm_rx_ba_notif+0x4ba/0x4d0 [iwlmvm]()
Q 4500, tid 8, flow 65535
Modules linked in: iwlmvm(O) mac80211(O) iwlwifi(O) cfg80211(O) compat(O) netconsole configfs ctr ccm arc4 autofs4 microcode bnep rfcomm snd_hda_codec_hdmi snd_hda_codec_idt snd_hda_codec_generic snd_hda_intel joydev snd_hda_codec uvcvideo videobuf2_core snd_hwdep videodev snd_pcm videobuf2_vmalloc videobuf2_memops i915 snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq snd_timer snd_seq_device drm_kms_helper dell_wmi dell_laptop drm btusb bluetooth snd psmouse i2c_algo_bit sparse_keymap wmi soundcore 6lowpan_iphc dcdbas serio_raw video lpc_ich ppdev mac_hid parport_pc nfsd nfs_acl auth_rpcgss nfs fscache binfmt_misc lockd sunrpc lp parport msdos sdhci_pci sdhci mmc_core ahci libahci e1000e ptp pps_core [last unloaded: compat]
CPU: 2 PID: 17707 Comm: irq/46-iwlwifi Tainted: G        W  O 3.14.17-patched #4
Hardware name: Dell Inc. Latitude E6430/0CPWYR, BIOS A09 12/13/2012
 00000000 00000000 ebd49d6c c1616221 f985dbdc ebd49d9c c1044e44 f9861df4
 ebd49dc8 0000452b f985dbdc 000003d0 f98395da f98395da ebd49f10 eaf3d8a4
 0000ffff ebd49db4 c1044f03 00000009 ebd49dac f9861df4 ebd49dc8 ebd49e64
Call Trace:
 [<c1616221>] dump_stack+0x41/0x52
 [<c1044e44>] warn_slowpath_common+0x84/0xa0
 [<f98395da>] ? iwl_mvm_rx_ba_notif+0x4ba/0x4d0 [iwlmvm]
 [<f98395da>] ? iwl_mvm_rx_ba_notif+0x4ba/0x4d0 [iwlmvm]
 [<c1044f03>] warn_slowpath_fmt+0x33/0x40
 [<f98395da>] iwl_mvm_rx_ba_notif+0x4ba/0x4d0 [iwlmvm]
 [<c10e3952>] ? ring_buffer_unlock_commit+0xa2/0xd0
 [<c10e9767>] ? trace_buffer_unlock_commit+0x37/0x50
 [<f98568a3>] ? iwl_tm_mvm_send_rx+0x53/0x90 [iwlmvm]
 [<f98327a8>] iwl_mvm_rx_dispatch+0x108/0x130 [iwlmvm]
 [<f9eac7e7>] iwl_pcie_irq_handler+0xf17/0x15b0 [iwlwifi]
 [<c10994c1>] irq_thread_fn+0x21/0x50
 [<c109926c>] irq_thread+0xec/0x110
 [<c10994a0>] ? irq_thread_dtor+0xb0/0xb0
 [<c10993f0>] ? irq_finalize_oneshot.part.34+0xc0/0xc0
 [<c1099180>] ? wake_threads_waitq+0x40/0x40
 [<c1062fdb>] kthread+0x9b/0xb0
 [<c1627137>] ret_from_kernel_thread+0x1b/0x28
 [<c1062f40>] ? flush_kthread_worker+0x90/0x90
---[ end trace 5e0f67374816db17 ]---
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Pull gpio fixes from Linus Walleij:
 "Here are some GPIO fixes, mainly affecting the DLN2 IRQ handling.
  Nothing special about them, just fixes:

   - Three patches fixing IRQ handling for the DLN2
   - Null pointer handling for grgpio"

* tag 'gpio-v3.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: dln2: use bus_sync_unlock instead of scheduling work
  gpio: grgpio: Avoid potential NULL pointer dereference
  gpio: dln2: Fix gpio output value in dln2_gpio_direction_output()
  gpio: dln2: fix issue when an IRQ is unmasked then enabled

Pull MMC fixes from Ulf Hansson:
 "MMC host:
   - sdhci-pci|acpi: Support some new IDs
   - sdhci: Fix sleep from atomic context
   - sdhci-pxav3: Prevent hang during ->probe()
   - sdhci: Disable re-tuning for HS400"

* tag 'mmc-v3.19-3' of git://git.linaro.org/people/ulf.hansson/mmc:
  mmc: sdhci-pci: Add support for Intel SPT
  mmc: sdhci-acpi: Add ACPI HID INT344D
  mmc: sdhci: Fix sleep in atomic after inserting SD card
  mmc: sdhci-pxav3: do the mbus window configuration after enabling clocks
  mmc: sdhci: Disable re-tuning for HS400
  mmc: sdhci: Simplify use of tuning timer
  mmc: sdhci: Add out_unlock to sdhci_execute_tuning
  mmc: sdhci: Tuning should not change max_blk_count

Pull scsi target fixes from Nicholas Bellinger:
 "Mostly minor fixes this time, including:

   - Add missing virtio-scsi -> TCM attribute conversion in vhost-scsi.
   - Fix persistent reservations write exclusive handling to allow
     readers for all registered I_T nexuses.
   - Drop arbitrary maximum I/O size limit in order to process I/Os
     larger than 4 MB, required for initiators that don't honor block
     limits EVPD.
   - Drop the now left-over fabric_max_sectors attribute"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  iscsi-target: Fix typos in enum cmd_flags_table
  MAINTAINERS: Add entry for iSER target driver
  target: Allow Write Exclusive non-reservation holders to READ
  target: Drop left-over fabric_max_sectors attribute
  target: Drop arbitrary maximum I/O size limit
  Documentation/target: Update fabric_ops to latest code
  vhost-scsi: Add missing virtio-scsi -> TCM attribute conversion

When batching up address ranges for TLB invalidation, we check tlb->end
!= 0 to indicate that some pages have actually been unmapped.

As of commit f045bbb9 ("mmu_gather: fix over-eager
tlb_flush_mmu_free() calling"), we use the same check for freeing these
pages in order to avoid a performance regression where we call
free_pages_and_swap_cache even when no pages are actually queued up.

Unfortunately, the range could have been reset (tlb->end = 0) by
tlb_end_vma, which has been shown to cause memory leaks on arm64.
Furthermore, investigation into these leaks revealed that the fullmm
case on task exit no longer invalidates the TLB, by virtue of tlb->end
 == 0 (in 3.18, need_flush would have been set).

This patch resolves the problem by reverting commit f045bbb9, using
instead tlb->local.nr as the predicate for page freeing in
tlb_flush_mmu_free and ensuring that tlb->end is initialised to a
non-zero value in the fullmm case.
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Dave Hansen <dave@sr71.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit e4c7f259 ("USB: kaweth.c: use GFP_ATOMIC under spin_lock")
makes sure that kaweth_internal_control_msg() allocates memory with GFP_ATOMIC,
but kaweth_internal_control_msg() also calls usb_start_wait_urb()
that still allocates memory with GFP_NOIO.

The patch fixes usb_start_wait_urb() as well.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>