Merge tag 'aspeed-4.14-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into next/dt

Pull "Aspeed devicetree updates for 4.14" from Joel Stanley:

 - fix to expose the full flash windows on ast2400.

* tag 'aspeed-4.14-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
  ARM: dts: aspeed-g4: fix AHB window size of the SMC controllers

Merge tag 'samsung-dt-4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt

Pull "Samsung DTS ARM changes for v4.14, part 2" from Krzysztof Kozłowski:

Fix PCI bus dtc warnings.

* tag 'samsung-dt-4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  ARM: dts: exynos: fix PCI bus dtc warnings

The window of the Aspeed AST2400 SMC Controllers to map chips on the
AHB Bus has a 256MB size. The full window range is

    [ 0x20000000 - 0x2FFFFFFF ] for the FMC controller
    [ 0x30000000 - 0x3FFFFFFF ] for the SPI controller

This change requires CONFIG_VMSPLIT_2G to be set.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>

Merge tag 'davinci-for-v4.14/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt

Pull "Add device-tree node for display on Lego Mindstorms EV3" from Sekhar Nori:

* tag 'davinci-for-v4.14/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
  ARM: dts: da850-lego-ev3: Add node for LCD display

Pull "arm: Xilinx Zynq DT fixes for v4.14" from Michal Simek:

- Remove earlycon
- Use C pre-processor
- Add fpga full region
- Add ethernet-phy as device-type
- Add adv7511 nodes to zc70x

* tag 'zynq-dt-for-4.14' of https://github.com/Xilinx/linux-xlnx:
  arm: zynq: Remove earlycon from bootargs
  arm: zynq: Use C pre-processor for includes in dts
  arm: zynq: Label whole PL part as fpga_full region
  arm: zynq: Add device-type property for zynq ethernet phy nodes
  arm: zynq: Add adv7511 on i2c bus for zc70x

This adds the operating points to the Ux500 device tree and
deletes the old special-purpose cpufreq node, as we can now
use the generic DT cpufreq driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Earlyconsole is used for early kernel debugging that's why this option
shouldn't be enabled by default.
Earlyconsole is partially copying the part of the bootlog after
"bootconsole [uart0] disabled".
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Change the dtsi include code to use the C pre-processor #include instead
of the device tree /include/. This brings all Zynq device trees inline
with each other.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

This will simplify dt overlay structure for the whole PL.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Mention device-type = "ethernet-phy", as qemu will need this in absence
of compatible.
Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Describe adv7511 on i2c bus.
Signed-off-by: Christian Kohn <christian.kohn@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

This adds a new node for the LEGO MINDSTORMS EV3 LCD display.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

Merge tag 'sunxi-dt-for-4.14-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt

Pull "Allwinner device tree changes for 4.14, round 2" from Chen-Yu Tsai:

The usual improvements:

  - AXP813/AXP818 PMIC (mfd and codec) enabled for Allwinner A83T boards

  - USB enabled for Allwinner A83T boards

* tag 'sunxi-dt-for-4.14-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  ARM: sun8i: a83t: h8homlet-v2: Enable USB ports
  ARM: sun8i: a83t: cubietruck-plus: Enable onboard USB peripherals
  ARM: sun8i: a83t: Add device node for USB OTG controller
  ARM: sun8i: a83t: Add USB PHY and host device nodes
  ARM: sun8i: a83t: h8homlet-v2: Enable AC100 combo chip in AXP818 PMIC
  ARM: sun8i: a83t: h8homlet-v2: Enable PMIC part of AXP818 PMIC
  ARM: sun8i: a83t: cubietruck-plus: Enable AC100 combo chip in AXP818 PMIC
  ARM: sun8i: a83t: cubietruck-plus: Enable PMIC part of AXP818 PMIC
  ARM: sun8i: a83t: Add device node and pinmux setting for RSB controller

dtc recently added PCI bus checks. Fix these warnings.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

dtc recently added PCI bus checks. Fix these warnings.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'renesas-dt-bindings2-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Pull "Second Round of Renesas ARM Based SoC DT Bindings Updates for v4.14" from Simon Horman:

* Add RZ/G1M (r8a7743) binding to apmu driver

  This allows SMP to be supported on the RZ/G1M SoC

* Add bindings for iW-RainboW-G22D-SODIMM RZ/G1E SODIMM development kit

  This is in preparation for adding DTS to support this hardware

* tag 'renesas-dt-bindings2-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  dt-bindings: apmu: Document r8a7743 support
  ARM: shmobile: document iW-RainboW-G22D SODIMM SOM Development Platform
  ARM: shmobile: document iW-RainboW-G22M-SM SODIMM System on Module

Merge tag 'renesas-dt2-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Pull "Second Round of Renesas ARM Based SoC DT Updates for v4.14" from Simon Horman:

* Use newly added Gen-3 fallback compat string

  This is consistent with ongoing efforts to use per-generation
  fallback strings where appropriate across devices found
  on R-Car SoCs. The aim of the effort being to strike a balance
  between the limited information available about the compatibility
  of devices found on different SoCs and the desire to ease enabling
  devices on new SoCs.

  This has no run-time effect due to the presence of a per-SoC
  compat string.

* Enable second CPU core on RZ/G1M (r8a7743)

  The RZ/G1M has two CA15 cores running at up to 1.5GHz

* Enable frequency scaling on RZ/G1M (r8a7743)

* Add six I2C cores to RZ/G1M (r8a7743) SoC DT

  This is a step towards enabling these cores on boards that use this SoC

* Add CEC clock for HDMI transmitter to R-Car M2-W (r8a7791) Koelsch

  Hans Verkuil says "The adv7511 on the Koelsch board has a 12 MHz fixed
  clock for the CEC block. Specify this in the dts to enable CEC support."

* Add PFC support to RZ/G1E (r8a7745) SoC and add Ethernet and SCIF2
  pins to SK-RZG1E board.

  This allows the kernel to control multiplexed pins for Ethernet
  and SCIF2 rather than relying on setup inherited at boot.

* tag 'renesas-dt2-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: dts: r8a7791: Use R-Car SATA Gen2 fallback compat string
  ARM: dts: r8a7790: Use R-Car SATA Gen2 fallback compat string
  ARM: dts: r8a7743: Add OPP table for frequency scaling
  ARM: dts: r8a7743: Add APMU node and second CPU core
  ARM: dts: koelsch: Add CEC clock for HDMI transmitter
  ARM: dts: sk-rzg1e: add Ether pins
  ARM: dts: sk-rzg1e: add SCIF2 pins
  ARM: dts: r8a7745: add PFC support
  ARM: dts: r8a7743: Add I2C DT support

Merge tag 'tegra-for-4.14-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt

Pull "ARM: tegra: Device tree changes for v4.14-rc1" from Thierry Reding:

One fix for Tegra124 to hook the host1x device up with the SMMU.

The remainder of this enables USB device mode on a couple of boards
where the port is currently unused.

* tag 'tegra-for-4.14-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  ARM: tegra: Enable UDC on AC100
  ARM: tegra: Enable UDC on Jetson TK1
  ARM: tegra: Enable UDC on Dalmore
  ARM: tegra: Enable UDC on Beaver
  ARM: tegra: Register host1x node with IOMMU binding on Tegra124

Merge tag 'zte-dt-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt

Pull "ZTE device tree updates for 4.14" from Shawn Guo:
 - A clean up patch from Shawn Lin to remove the deprecated dwmmc
   property 'num-slots'.

* tag 'zte-dt-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: dts: zte: remove num-slots from zx296702-ad1

Merge tag 'imx-dt-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt

Pull "i.MX device tree updates for 4.14" from Shawn Guo:
 - A series from Andrew Lunn updating imx6-rdu2 board to enable
   on-board Marvell switch support.
 - A series from Jagan Teki updating imx6ul-isiot and imx6ul-geam to
   enable audio card and FEC support.
 - Add support for Toradex Ixora V1.1 and Apalis Evaluation Board
   along with some cleanups.
 - Enable DRM display support for imx6ul-evk and imx7d-sdb board.
 - Add i.MX53 based Beckhoff CX9020 board support.
 - Add GPMI NAND and APBH DMA devices for i.MX7 and enables NAND support
   for imx7-colibri board.
 - Enables the ADV7180 analog video decoder sensor connected to the
   IMX6 IPU on various Gateworks Ventana boards.
 - Minor updates on misc boards and some random cleanups.

* tag 'imx-dt-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (47 commits)
  ARM: dts: imx6q-bx50v3: Enable i2c recovery mechanism
  ARM: dts: imx6q-apalis-eval: add support for Apalis Evaluation Board
  ARM: dts: imx6: add support for Toradex Ixora V1.1 carrier board
  ARM: dts: imx6qdl-apalis: imx6q-apalis-ixora: use i2c from dwc hdmi
  ARM: dts: imx6q-apalis-ixora: add camera i2c bus definition
  ARM: dts: imx6q-apalis-ixora: get rid of obsolete fusion comment
  ARM: dts: imx6qdl-apalis: reword cam i2c comment
  ARM: dts: imx6qdl-apalis: imx6q-apalis-ixora: get rid of tegra legacy gen1_i2c comment
  ARM: dts: imx6q-apalis-ixora: combine aliases
  ARM: dts: imx6qdl-apalis: split usdhc1 pinctrl to support 4- and 8-bit
  ARM: dts: imx6q-apalis-ixora: fix usdhc2 pinctrl property
  ARM: dts: imx6ul-liteboard: Support poweroff
  ARM: dts: imx: add CX9020 Embedded PC device tree
  ARM: dts: imx53: add alternative UART2 configuration
  ARM: dts: imx53: add srtc node
  dt-bindings: arm: Add entry for Beckhoff CX9020
  ARM: dts: i.MX25: add RNGB node to dtsi
  ARM: dts: imx6ul-14x14-evk: Remove unrelated pin from ENET group
  ARM: dts: imx7d-sdb: Add flexcan support
  ARM: dts: imx7-colibri: add NAND support
  ...

Pull "Broadcom devicetree changes for 4.14" from Florian Fainelli:

This pull request contains Broadcom ARM-based SoCs Device Tree changes for
4.14, please pull the following:

- Eric moves the bcm2837 DT file from arm64 to arm because it created a maintenance
  problem and would have required either duplication or cross merges

- Stefan changes how the pinmuxing is defined and pushes it at the board level
  to support Raspberry Pi Zero Wireless. He then adds supports for the actual
  Raspberry Pi Zero Wireless board along with binding documentation. Stefan
  also defines a proper SMP enable-method property and binding for BCM2836
  (Raspbery Pi 2)

- Rafal describes the BCM5301X USB ports correctly in Device Tree such that
  it becomes possible to assign them to specific LED triggers (e.g: USB activity).
  He does the same thing for BCM53573 and defines default LED triggers for USB.

- Jon provides a fix for Northstar Plus which consists in correctly defining
  the "dma-coherent" property for peripherals which are DMA coherent. He also
  does a bit of re-arrangement of the USB DT nodes and finally adds USB 3 PHY
  and host controller support for NorthStar Plus

- Florian adds support for Broadcom's BCM947189ACDBMR reference board which is
  based on BCM47182/53573 and which supports external MoCA (BCM6802)

- Ray fixes the wrong UART2 base address for Cygnus

- Scott moves the v3d node in the proper unit address order and defines the correct
  UART alias for the BCM91130_entphn reference board to be UART3

- Jason adds the DT node for the Cygnus Cortex-A9 Performance Monitoring Unit

- Jonathan adds a bunch of additional peripherals to the Cygnus DTS include file:
  SDHCI, Keypad, SPI, DMA and pinmux configurations

- Raveendra adds the Cygnus OHCI and EHCI Device Tree nodes

* tag 'arm-soc/for-4.14/devicetree' of http://github.com/Broadcom/stblinux:
  ARM: BCM53573: Specify ports for USB LED for Tenda AC9
  ARM: dts: cygnus: Add generic-ehci/ohci nodes
  ARM: dts: cygnus: add serial0 alias for uart3 on bcm91130_entphn
  ARM: dts: cygnus: Add additional peripherals to dtsi
  ARM: dts: cygnus: Enable Performance Monitoring Unit
  ARM: dts: cygnus: place v3d in proper address ordered location
  ARM: dts: cygnus: Fix incorrect UART2 register base
  ARM: dts: bcm283x: Add 32-bit enable method for SMP
  dt-bindings: arm: add SMP enable-method for BCM2836
  ARM: dts: BCM53573: Add Broadcom BCM947189ACDBMR board support
  ARM: dts: BCM5301X: Specify USB ports for USB LEDs of few devices
  ARM: dts: NSP: Add USB3 and USB3 PHY to NSP
  ARM: dts: NSP: Rearrage USB entries
  ARM: dts: NSP: Add dma-coherent to relevant DT entries
  ARM: dts: bcm2835: Add Raspberry Pi Zero W
  dt-bindings: bcm: Add Raspberry Pi Zero W
  ARM: bcm283x: Define UART pinmuxing on board level
  ARM: dts: BCM5301X: Specify USB ports for each controller
  ARM: dts: bcm283x: Move the BCM2837 DT contents from arm64 to arm.

Merge tag 'omap-for-v4.14/dt-v3-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

Pull "device tree changes for omaps for v4.14, part2" from Tony Lindgren:

Second set of device tree changes for omaps for v4.14 merge window.
These got delayed a bit because the iodelay changes had to be
reworked for a missing Signed-off-by. And the beagleboard-x15
wants to use iodelay too for mmc:

- A series of changes to add dra7 iodelay data used for mmc

- Add support for new beagleBoard-x15 revision c

- Fix logicpd-torpedo-37xx-devkit mmc card detect direction

* tag 'omap-for-v4.14/dt-v3-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: omap3: logicpd-torpedo-37xx-devkit: Fix MMC1 cd-gpio
  ARM: dts: am57xx-beagle-x15: Add support for rev C
  ARM: dts: dra71-evm: Add pinmux configuration for MMC
  ARM: dts: dra72-evm-revc: Add pinmux configuration for MMC
  ARM: dts: dra72-evm: Add pinmux configuration for MMC
  ARM: dts: am572x-idk: Add pinmux configuration for MMC
  ARM: dts: am571x-idk: Add pinmux configuration for MMC
  ARM: dts: am57xx-idk: Move common MMC/SD properties to common file
  ARM: dts: am57xx-beagle-x15: Add pinmux configuration for MMC
  ARM: dts: dra7-evm: Add pinmux configuration for MMC
  ARM: dts: dra74x: Create a common file with MMC/SD IOdelay data
  ARM: dts: dra72x: Create a common file with MMC/SD IOdelay data

The h8homlet board has the A83T's standard USB 1.1/2.0 host pair routed
to a USB host port on the board. The other USB host port is routed to
USB OTG controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

The Cubietruck-plus has a GL830 USB-to-SATA bridge connected to EHCI0,
and a USB3503 HSIC USB 2.0 hub connected to EHCI1. The USB3503's I2C
control interface is not connected.

This patch enables both EHCI controllers, adds a device node for the
USB hub, and includes sunxi-common-regulators.dtsi for the VBUS
regulators. The existing reg_vcc3v3 is dropped as it is also available
in the set of common regulators. Other unused regulators are disabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

The USB OTG controller found on the A83T is compatible with the one
found on the A33.

Add a device node for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

The A83T has 3 USB PHYs, 1 for USB OTG, 1 for standard USB 2.0, 1 for
USB HSIC. EHCI0/OHCI0 are the standard USB host pair, while EHCI1 is
the host controller for HSIC. OTG is not added yet.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This uses trigger-sources documented in commit 80dc6e1c ("dt-bindings:
leds: document new trigger-sources property") to specify USB ports. Such an
information can be used by operating system to setup LEDs behavior.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add dt nodes for generic-ehci/ohci host controller.
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Use serial0 alias to select stdout-path on Cygnus bcm911360_entphon
board.
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add nodes for peripherals in Cygnus dtsi: sdhci, keypad, spi, dma,
pinmux configs.
Signed-off-by: Jonathan Richardson <jonathan.richardson@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add PMU capability to Cygnus so trace and performance profiling
can be used.
Signed-off-by: Jason Uy <jason.uy@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Move v3d devicetree node to proper address ordered location in Cygnus
dtsi.
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Fix incorrect Cygnus UART2 register base.

Fixes: 0f0b21a8 ("ARM: dts: Move all Cygnus peripherals into axi bus")
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

This pull request brings in a new SMP enable-method compat string,
which is needed to move the 32-bit SMP boot code out of the irqchip.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Fixes commit 687c2767 ("ARM: dts: Add minimal support for LogicPD
Torpedo DM3730 devkit")

This patch corrects an issue where the cd-gpios was improperly setup
using IRQ_TYPE_LEVEL_LOW instead of GPIO_ACTIVE_LOW.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Latest update to the BeagleBoard-X15 platform (revision C). This board contains
a silicon update (Rev 2.0), which includes a fix for the 2nd ethernet phy when
running at 1000 Mbps speeds.

This board can be indentified by the [C.00] after [BBRDX15_] in the at24 eeprom:
[BBRDX15_C.001731PX150249]

Rev C is now in full production and boards are available for end users.

https://beagleboard.org/x15
https://github.com/beagleboard/beagleboard-x15/Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Nishanth Menon <nm@ti.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Kishon Vijay Abraham I <kishon@ti.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Override the compatible string of the first USB controller to enable
device mode.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Override the compatible string of the first USB controller to enable
device mode.
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Override the compatible string of the first USB controller to enable
device mode.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Override the compatible string of the first USB controller to enable
device mode.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>