In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().

Fixes: c8846e10 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Clients should poll for more packets afterwards
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This feature has been reported to cause stability issues on several systems.
Disable it until it has been fixed and verified. It can still be enabled
through debugfs
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fixes a rare corner case if the txq dequeue attempt fails, but mac80211
still has PS buffered packets
Signed-off-by: Felix Fietkau <nbd@nbd.name>

These packets have no txwi entry in the ring, so tracking via tx status does
not work. To prevent PS poll requests from being unanswered, end the service
period right away
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Also fix the size check for filtered powersave frames
Fixes a corner case with waking up clients
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Make the queue index match the hardware queue on which they get sent out
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fixes sending them, otherwise they loop back right into the buffer
Signed-off-by: Felix Fietkau <nbd@nbd.name>

AGC register 35, 37 override for the low gain setting should only be done
on 5 GHz. Also, 2.4 GHz needs a different value for register 35
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Devices with external LNA need different values for AGC registers 8 and 9
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use the correct variable in the check. Fixes an uninitialized variable warning
Reported-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Fixes: c8846e10 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Full tx blocking (as opposed to CCA blocking) should only happen if there
is a continuous non-802.11 signal above the energy detect threshold.
Unfortunately the ED/CCA counter can't detect that, as it also counts 802.11
signals as busy.

Similar to the vendor code, implement a learning mode that waits until the AGC
gain has already been adjusted to the lowest value (due to false CCA events),
and the number of false CCA events still remains high, and the blocking
threshold is exceeded for more than 5 seconds.
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Also update the mask first before calculating the vif index.
Fixes an issue where adding back the same interfaces in a different order
fails because of duplicate vif index use

Fixes: 06662264 ("mt76x02: use mask for vifs")
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Since we add txwi at the begining of skb->data, it no longer point
to ieee80211_hdr. This breaks settings TS bit for probe response and
beacons.
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Restart the firmware and re-initialize the MAC to be able to recover
from more kinds of hang states
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Preparation for full device restart support
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Useful in case the hardware reset clobbers these values
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce mt76_queue stopped parameter in order to run
ieee80211_wake_queue only when mac80211 queues have been
previously stopped and avoid to disable interrupts when
it is not necessary
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

dst_cache_destroy will be called in dst_release

dst_release-->dst_destroy_rcu-->dst_destroy-->metadata_dst_free
-->dst_cache_destroy

It should not call dst_cache_destroy before dst_release

Fixes: 41411e2f ("net/sched: act_tunnel_key: Add dst_cache support")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix regression bug introduced in
commit 365ad353 ("tipc: reduce risk of user starvation during link
congestion")

Only signal -EDESTADDRREQ for RDM/DGRAM if we don't have a cached
sockaddr.

Fixes: 365ad353 ("tipc: reduce risk of user starvation during link congestion")
Signed-off-by: Erik Hugne <erik.hugne@gmail.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull MIPS updates from Paul Burton:

 - Support for the MIPSr6 MemoryMapID register & Global INValidate TLB
   (GINVT) instructions, allowing for more efficient TLB maintenance
   when running on a CPU such as the I6500 that supports these.

 - Enable huge page support for MIPS64r6.

 - Optimize post-DMA cache sync by removing that code entirely for
   kernel configurations in which we know it won't be needed.

 - The number of pages allocated for interrupt stacks is now calculated
   correctly, where before we would wastefully allocate too much memory
   in some configurations.

 - The ath79 platform migrates to devicetree.

 - The bcm47xx platform sees fixes for the Buffalo WHR-G54S board.

 - The ingenic/jz4740 platform gains support for appended devicetrees.

 - The cavium_octeon, lantiq, loongson32 & sgi-ip27 platforms all see
   cleanups as do various pieces of core architecture code.

* tag 'mips_5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (66 commits)
  MIPS: lantiq: Remove separate GPHY Firmware loader
  MIPS: ingenic: Add support for appended devicetree
  MIPS: SGI-IP27: rework HUB interrupts
  MIPS: SGI-IP27: do boot CPU init later
  MIPS: SGI-IP27: do xtalk scanning later
  MIPS: SGI-IP27: use pr_info/pr_emerg and pr_cont to fix output
  MIPS: SGI-IP27: clean up bridge access and header files
  MIPS: SGI-IP27: get rid of volatile and hubreg_t
  MIPS: irq: Allocate accurate order pages for irq stack
  MIPS: dma-noncoherent: Remove bogus condition in dma_sync_phys()
  MIPS: eBPF: Remove REG_32BIT_ZERO_EX
  MIPS: eBPF: Always return sign extended 32b values
  MIPS: CM: Fix indentation
  MIPS: BCM47XX: Fix/improve Buffalo WHR-G54S support
  MIPS: OCTEON: program rx/tx-delay always from DT
  MIPS: OCTEON: delete board-specific link status
  MIPS: OCTEON: don't lie about interface type of CN3005 board
  MIPS: OCTEON: warn if deprecated link status is being used
  MIPS: OCTEON: add fixed-link nodes to in-kernel device tree
  MIPS: Delete unused flush_cache_sigtramp()
  ...

Pull parisc updates from Helge Deller:
 "The most important changes in this patch set are:

   - DMA-related cleanups for parisc with the aim to move anything not
     required by drivers out of <asm/dma-mapping.h>, by Christoph
     Hellwig

   - Switch to memblock_alloc(), by Mike Rapoport

   - Makefile cleanups by Masahiro Yamada

   - Switch to bust_spinlocks(), by Sergey Senozhatsky

   - Improved initial SMP affinity selection for IRQs

   - Added IPI- and rescheduling interrupts in /proc/interrupts output"

* 'parisc-5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux: (21 commits)
  parisc: use memblock_alloc() instead of custom get_memblock()
  parisc: Add constants for various PDC firmware calls
  parisc: Add constant for PDC_PAT_COMPLEX firmware call
  parisc: Show machine product number during boot
  parisc: Add constants for PDC_RELOCATE PDC call
  parisc: Add PDC_CRASH_PREP PDC function number
  parisc: Use F_EXTEND() macro in iosapic code
  parisc: remove the HBA_DATA macro
  parisc/lba_pci: use container_of in LBA_DEV
  parisc/dino: use container_of in DINO_DEV
  parisc: properly type the return value of parisc_walk_tree
  parisc: properly type the iommu field in struct pci_hba_data
  parisc: turn GET_IOC into an inline function
  parisc: move internal implementation details out of <asm/dma-mapping.h>
  parisc: don't include <asm/cacheflush.h> in <asm/dma-mapping.h>
  parisc: remove meaningless ccflags-y in arch/parisc/boot/Makefile
  parisc: replace oops_in_progress manipulation with bust_spinlocks()
  parisc: Improve initial IRQ to CPU assignment
  parisc: Count IPI function call interrupts
  parisc: Show rescheduling interrupts on SMP machines only
  ...

Pull s390 updates from Martin Schwidefsky:

 - A copy of Arnds compat wrapper generation series

 - Pass information about the KVM guest to the host in form the control
   program code and the control program version code

 - Map IOV resources to support PCI physical functions on s390

 - Add vector load and store alignment hints to improve performance

 - Use the "jdd" constraint with gcc 9 to make jump labels working again

 - Remove amode workaround for old z/VM releases from the DCSS code

 - Add support for in-kernel performance measurements using the CPU
   measurement counter facility

 - Introduce a new PMU device cpum_cf_diag to capture counters and store
   thenn as event raw data.

 - Bug fixes and cleanups

* tag 's390-5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (54 commits)
  Revert "s390/cpum_cf: Add kernel message exaplanations"
  s390/dasd: fix read device characteristic with CONFIG_VMAP_STACK=y
  s390/suspend: fix prefix register reset in swsusp_arch_resume
  s390: warn about clearing als implied facilities
  s390: allow overriding facilities via command line
  s390: clean up redundant facilities list setup
  s390/als: remove duplicated in-place implementation of stfle
  s390/cio: Use cpa range elsewhere within vfio-ccw
  s390/cio: Fix vfio-ccw handling of recursive TICs
  s390: vfio_ap: link the vfio_ap devices to the vfio_ap bus subsystem
  s390/cpum_cf: Handle EBUSY return code from CPU counter facility reservation
  s390/cpum_cf: Add kernel message exaplanations
  s390/cpum_cf_diag: Add support for s390 counter facility diagnostic trace
  s390/cpum_cf: add ctr_stcctm() function
  s390/cpum_cf: move common functions into a separate file
  s390/cpum_cf: introduce kernel_cpumcf_avail() function
  s390/cpu_mf: replace stcctm5() with the stcctm() function
  s390/cpu_mf: add store cpu counter multiple instruction support
  s390/cpum_cf: Add minimal in-kernel interface for counter measurements
  s390/cpum_cf: introduce kernel_cpumcf_alert() to obtain measurement alerts
  ...

Pull m68k updates from Geert Uytterhoeven:

 - VLA removal

 - gcc-8.x build fixes

 - small improvements and cleanups

 - defconfig updates

* tag 'm68k-for-v5.1-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k: Add -ffreestanding to CFLAGS
  m68k/apollo: Fix comment in Makefile
  dio: Fix buffer overflow in case of unknown board
  m68k/defconfig: Update defconfigs for v5.0-rc1
  m68k/atari: Avoid VLA use in atari_switches_setup()
  m68k: Avoid VLA use in mangle_kernel_stack()
  m68k/mac: Use '030 reset method on SE/30
  m68k/mac: Remove obsolete comment
  m68k/mac: Skip VIA port setup unless RTC is connected
  m68k/mac: Clean up unused timer definitions
  m68k/defconfig: Drop NET_VENDOR_<FOO>=n

Linux supports ELF binaries for ~25 years now.  a.out coredumping has
bitrotten quite significantly and would need some fixing to get it into
shape again but considering how even the toolchains cannot create a.out
executables in its default configuration, let's deprecate a.out support
and remove it a couple of releases later, instead.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Richard Weinberger <richard@nod.at>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Jann Horn <jannh@google.com>
Cc: <linux-api@vger.kernel.org>
Cc: <linux-fsdevel@vger.kernel.org>
Cc: lkml <linux-kernel@vger.kernel.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: <x86@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We're (finally) phasing out a.out support for good.  As Borislav Petkov
points out, we've supported ELF binaries for about 25 years by now, and
coredumping in particular has bitrotted over the years.

None of the tool chains even support generating a.out binaries any more,
and the plan is to deprecate a.out support entirely for the kernel.  But
I want to start with just removing the core dumping code, because I can
still imagine that somebody actually might want to support a.out as a
simpler biinary format.

Particularly if you generate some random binaries on the fly, ELF is a
much more complicated format (admittedly ELF also does have a lot of
toolchain support, mitigating that complexity a lot and you really
should have moved over in the last 25 years).

So it's at least somewhat possible that somebody out there has some
workflow that still involves generating and running a.out executables.

In contrast, it's very unlikely that anybody depends on debugging any
legacy a.out core files.  But regardless, I want this phase-out to be
done in two steps, so that we can resurrect a.out support (if needed)
without having to resurrect the core file dumping that is almost
certainly not needed.

Jann Horn pointed to the <asm/a.out-core.h> file that my first trivial
cut at this had missed.

And Alan Cox points out that the a.out binary loader _could_ be done in
user space if somebody wants to, but we might keep just the loader in
the kernel if somebody really wants it, since the loader isn't that big
and has no really odd special cases like the core dumping does.
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Cc: Jann Horn <jannh@google.com>
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull crypto update from Herbert Xu:
 "API:
   - Add helper for simple skcipher modes.
   - Add helper to register multiple templates.
   - Set CRYPTO_TFM_NEED_KEY when setkey fails.
   - Require neither or both of export/import in shash.
   - AEAD decryption test vectors are now generated from encryption
     ones.
   - New option CONFIG_CRYPTO_MANAGER_EXTRA_TESTS that includes random
     fuzzing.

  Algorithms:
   - Conversions to skcipher and helper for many templates.
   - Add more test vectors for nhpoly1305 and adiantum.

  Drivers:
   - Add crypto4xx prng support.
   - Add xcbc/cmac/ecb support in caam.
   - Add AES support for Exynos5433 in s5p.
   - Remove sha384/sha512 from artpec7 as hardware cannot do partial
     hash"

[ There is a merge of the Freescale SoC tree in order to pull in changes
  required by patches to the caam/qi2 driver. ]

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (174 commits)
  crypto: s5p - add AES support for Exynos5433
  dt-bindings: crypto: document Exynos5433 SlimSSS
  crypto: crypto4xx - add missing of_node_put after of_device_is_available
  crypto: cavium/zip - fix collision with generic cra_driver_name
  crypto: af_alg - use struct_size() in sock_kfree_s()
  crypto: caam - remove redundant likely/unlikely annotation
  crypto: s5p - update iv after AES-CBC op end
  crypto: x86/poly1305 - Clear key material from stack in SSE2 variant
  crypto: caam - generate hash keys in-place
  crypto: caam - fix DMA mapping xcbc key twice
  crypto: caam - fix hash context DMA unmap size
  hwrng: bcm2835 - fix probe as platform device
  crypto: s5p-sss - Use AES_BLOCK_SIZE define instead of number
  crypto: stm32 - drop pointless static qualifier in stm32_hash_remove()
  crypto: chelsio - Fixed Traffic Stall
  crypto: marvell - Remove set but not used variable 'ivsize'
  crypto: ccp - Update driver messages to remove some confusion
  crypto: adiantum - add 1536 and 4096-byte test vectors
  crypto: nhpoly1305 - add a test vector with len % 16 != 0
  crypto: arm/aes-ce - update IV after partial final CTR block
  ...

Pull networking updates from David Miller:
 "Here we go, another merge window full of networking and #ebpf changes:

   1) Snoop DHCPACKS in batman-adv to learn MAC/IP pairs in the DHCP
      range without dealing with floods of ARP traffic, from Linus
      Lüssing.

   2) Throttle buffered multicast packet transmission in mt76, from
      Felix Fietkau.

   3) Support adaptive interrupt moderation in ice, from Brett Creeley.

   4) A lot of struct_size conversions, from Gustavo A. R. Silva.

   5) Add peek/push/pop commands to bpftool, as well as bash completion,
      from Stanislav Fomichev.

   6) Optimize sk_msg_clone(), from Vakul Garg.

   7) Add SO_BINDTOIFINDEX, from David Herrmann.

   8) Be more conservative with local resends due to local congestion,
      from Yuchung Cheng.

   9) Allow vetoing of unsupported VXLAN FDBs, from Petr Machata.

  10) Add health buffer support to devlink, from Eran Ben Elisha.

  11) Add TXQ scheduling API to mac80211, from Toke Høiland-Jørgensen.

  12) Add statistics to basic packet scheduler filter, from Cong Wang.

  13) Add GRE tunnel support for mlxsw Spectrum-2, from Nir Dotan.

  14) Lots of new IP tunneling forwarding tests, also from Nir Dotan.

  15) Add 3ad stats to bonding, from Nikolay Aleksandrov.

  16) Lots of probing improvements for bpftool, from Quentin Monnet.

  17) Various nfp drive #ebpf JIT improvements from Jakub Kicinski.

  18) Allow #ebpf programs to access gso_segs from skb shared info, from
      Eric Dumazet.

  19) Add sock_diag support for AF_XDP sockets, from Björn Töpel.

  20) Support 22260 iwlwifi devices, from Luca Coelho.

  21) Use rbtree for ipv6 defragmentation, from Peter Oskolkov.

  22) Add JMP32 instruction class support to #ebpf, from Jiong Wang.

  23) Add spinlock support to #ebpf, from Alexei Starovoitov.

  24) Support 256-bit keys and TLS 1.3 in ktls, from Dave Watson.

  25) Add device infomation API to devlink, from Jakub Kicinski.

  26) Add new timestamping socket options which are y2038 safe, from
      Deepa Dinamani.

  27) Add RX checksum offloading for various sh_eth chips, from Sergei
      Shtylyov.

  28) Flow offload infrastructure, from Pablo Neira Ayuso.

  29) Numerous cleanups, improvements, and bug fixes to the PHY layer
      and many drivers from Heiner Kallweit.

  30) Lots of changes to try and make packet scheduler classifiers run
      lockless as much as possible, from Vlad Buslov.

  31) Support BCM957504 chip in bnxt_en driver, from Erik Burrows.

  32) Add concurrency tests to tc-tests infrastructure, from Vlad
      Buslov.

  33) Add hwmon support to aquantia, from Heiner Kallweit.

  34) Allow 64-bit values for SO_MAX_PACING_RATE, from Eric Dumazet.

  And I would be remiss if I didn't thank the various major networking
  subsystem maintainers for integrating much of this work before I even
  saw it. Alexei Starovoitov, Daniel Borkmann, Pablo Neira Ayuso,
  Johannes Berg, Kalle Valo, and many others. Thank you!"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2207 commits)
  net/sched: avoid unused-label warning
  net: ignore sysctl_devconf_inherit_init_net without SYSCTL
  phy: mdio-mux: fix Kconfig dependencies
  net: phy: use phy_modify_mmd_changed in genphy_c45_an_config_aneg
  net: dsa: mv88e6xxx: add call to mv88e6xxx_ports_cmode_init to probe for new DSA framework
  selftest/net: Remove duplicate header
  sky2: Disable MSI on Dell Inspiron 1545 and Gateway P-79
  net/mlx5e: Update tx reporter status in case channels were successfully opened
  devlink: Add support for direct reporter health state update
  devlink: Update reporter state to error even if recover aborted
  sctp: call iov_iter_revert() after sending ABORT
  team: Free BPF filter when unregistering netdev
  ip6mr: Do not call __IP6_INC_STATS() from preemptible context
  isdn: mISDN: Fix potential NULL pointer dereference of kzalloc
  net: dsa: mv88e6xxx: support in-band signalling on SGMII ports with external PHYs
  cxgb4/chtls: Prefix adapter flags with CXGB4
  net-sysfs: Switch to bitmap_zalloc()
  mellanox: Switch to bitmap_zalloc()
  bpf: add test cases for non-pointer sanitiation logic
  mlxsw: i2c: Extend initialization by querying resources data
  ...

This reverts commit fb3a0b61.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Merge tag 'leds-for-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds

Pull LED updates from Jacek Anaszewski:

 - finalize previously announced support for initialization of pattern
   triggers from Device Tree

 - fix for null deref on firmware load failure in leds-lp55xx-common.c

* tag 'leds-for-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
  leds: lp55xx: fix null deref on firmware load failure
  leds: trigger: timer: Add initialization from Device Tree
  leds: trigger: oneshot: Add initialization from Device Tree
  leds: trigger: pattern: Add pattern initialization from Device Tree
  leds: Add helper for getting default pattern from Device Tree
  dt-bindings: leds: Add pattern initialization from Device Tree

Pull hwmon updates from Guenter Roeck:

 - Add support for LM96000, DPS-650AB to existing drivers

 - Use permission specific SENSOR[_DEVICE]_ATTR variants in several
   drivers

 - Replace S_<PERMS> with octal values in several drivers

 - Update some license headers

 - Various minor fixes and improvements in several drivers

* tag 'hwmon-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (89 commits)
  dt-bindings: hwmon: Add missing documentation for lm75
  hwmon: (ad7418) Add device tree probing
  hwmon: (ad741x) Add DT bindings for Analog Devices AD741x
  hwmon: (ntc_thermistor) Convert to new hwmon API
  hwmon: (pwm-fan) Add optional regulator support
  dt-bindings: hwmon: Add optional regulator support to pwm-fan
  hwmon: (f71882fg) Mark expected switch fall-through
  hwmon: (ad7418) Catch I2C errors
  hwmon: (lm85) add support for LM96000 high frequencies
  hwmon: (lm85) support the LM96000
  dt-bindings: Add LM96000 as a trivial device
  hwmon: (lm85) remove freq_map size hardcodes
  hwmon: (occ) Fix license headers
  hwmon: (via-cputemp) Use permission specific SENSOR[_DEVICE]_ATTR variants
  hwmon: (vexpress-hwmon) Use permission specific SENSOR[_DEVICE]_ATTR variants
  hwmon: (tmp421) Replace S_<PERMS> with octal values
  hwmon: (tmp103) Use permission specific SENSOR[_DEVICE]_ATTR variants
  hwmon: (tmp102) Replace S_<PERMS> with octal values
  hwmon: (tc74) Use permission specific SENSOR[_DEVICE]_ATTR variants
  hwmon: (tc654) Use permission specific SENSOR[_DEVICE]_ATTR variants
  ...

Pull spi updates from Mark Brown:
 "A fairly quiet release for SPI, the biggest thing is the conversion to
  use GPIO descriptors which is now 90% done but still needs some
  stragglers converting.

  Summary:

   - Support for inter-word delays

   - Conversion of the core and most drivers to use GPIO descriptors for
     GPIO controlled chip selects

   - New drivers for NXP FlexSPI and QuadSPI, SiFive and Spreadtrum"

* tag 'spi-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (104 commits)
  spi: sh-msiof: Restrict bits per word to 8/16/24/32 on R-Car Gen2/3
  spi: sifive: Remove redundant dev_err call in sifive_spi_probe()
  spi: sifive: Remove spi_master_put in sifive_spi_remove()
  spi: spi-gpio: fix SPI_CS_HIGH capability
  spi: pxa2xx: Setup maximum supported DMA transfer length
  spi: sifive: Add driver for the SiFive SPI controller
  spi: sifive: Add DT documentation for SiFive SPI controller
  spi: sprd: Add a prefix for SPI DMA channel macros
  spi: sprd: spi: sprd: Add DMA mode support
  dt-bindings: spi: Add the DMA properties for the SPI dma mode
  spi: sprd: Add the SPI irq function for the SPI DMA mode
  dt-bindings: spi: imx: Add an entry for the i.MX8QM compatible
  spi: use gpio[d]_set_value_cansleep for setting chipselect GPIO
  spi: gpio: Advertise support for SPI_CS_HIGH
  spi: sh-msiof: Replace spi_master by spi_controller
  spi: sh-hspi: Replace spi_master by spi_controller
  spi: rspi: Replace spi_master by spi_controller
  spi: atmel-quadspi: add support for sam9x60 qspi controller
  dt-bindings: spi: atmel-quadspi: QuadSPI driver for Microchip SAM9X60
  spi: atmel-quadspi: add support for named peripheral clock
  ...

Pull regulator updates from Mark Brown:
 "The bulk of the standout changes in this release are cleanups, with
  the core work being a combination of factoring out common code into
  helpers and the completion of the conversion of the core to use GPIO
  descriptors.

  Summary:

   - Addition of helper functions for current limits and conversion of
     drivers to use them by Axel Lin.

   - Lots and lots of cleanups from Axel Lin.

   - Conversion of the core to use GPIO descriptors rather than numbers
     by Linus Walleij.

   - New drivers for Maxim MAX77650 and ROHM BD70528"

* tag 'regulator-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (131 commits)
  regulator: mc13xxx: Constify regulator_ops variables
  regulator: palmas: Constify palmas_smps_ramp_delay array
  regulator: wm831x-dcdc: Convert to use regulator_set/get_current_limit_regmap
  regulator: pv88090: Convert to use regulator_set/get_current_limit_regmap
  regulator: pv88080: Convert to use regulator_set/get_current_limit_regmap
  regulator: pv88060: Convert to use regulator_set/get_current_limit_regmap
  regulator: max77650: Convert to use regulator_set/get_current_limit_regmap
  regulator: lp873x: Convert to use regulator_set/get_current_limit_regmap
  regulator: lp872x: Convert to use regulator_set/get_current_limit_regmap
  regulator: da9210: Convert to use regulator_set/get_current_limit_regmap
  regulator: da9055: Convert to use regulator_set/get_current_limit_regmap
  regulator: core: Add set/get_current_limit helpers for regmap users
  regulator: Fix comment for csel_reg and csel_mask
  regulator: stm32-vrefbuf: add power management support
  regulator: 88pm8607: Remove unused fields from struct pm8607_regulator_info
  regulator: 88pm8607: Simplify pm8607_list_voltage implementation
  regulator: cpcap: Constify omap4_regulators and xoom_regulators
  regulator: cpcap: Remove unused vsel_shift from struct cpcap_regulator
  dt-bindings: regulator: tps65218: rectify units of LS3
  dt-bindings: regulator: add LS2 load switch documentation
  ...

Pull regmap updates from Mark Brown:
 "There are only two changes here:

   - fix for conflicting attributes on the rbtree node structure

   - implementation of main status register support in the interrupt
     code which supports chips that have a register to cut down on the
     number of per-interrupt status registers that need to be checked
     when handling interrupts"

* tag 'regmap-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: Remove attribute packed from struct 'regcache_rbtree_node'
  regmap: regmap-irq: Add main status register support

Pull MMC updates from Ulf Hansson:
 "MMC core:
   - Fixup max_discard/trim calculations
   - Announce SD specs greater than 4.0
   - Add discard support for SD cards
   - Don't do retries for CMD6 (SWITCH command)
   - Various cleanups and re-structuring

  MMC host:
   - cqhci:
      * Add maintainers for eMMC CQHCI driver
   - sdhci:
      * Consolidate WP GPIO code
      * Add ADMA3 DMA support for V4 enabled host
      * Fixup card detect support in pci-o2micro driver
      * Add support for CMDQ and SDMMC pads auto-calibration in tegra
        driver
      * Add DCMD support and CMDQ support, support for i.MX6ULL variant,
        fixup HS400 timing issue and add HS400_ES support for i.MX8QXP
        to esdhc-imx driver
      * Avoid CRC errors by adjusting settings to speed mode and fixup
        card initialization for high speed mode in renesas_sdhi
      * Fixup timeout settings for omap
      * Enable 8 bits bus-width support in atmel-mci
      * Convert some legacy code in jz4740 driver to use modern APIs
      * Send a CMD12 to clear DPSM at errors for STM32 sdmmc mmci
        driver"

* tag 'mmc-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (69 commits)
  mmc:fix a bug when max_discard is 0
  mmc: core: Add a debug print when the card may have been replaced
  mmc: core: Add sd discard timeout
  mmc: core: Add discard support to sd
  mmc: sdhci-esdhc-imx: clear the HALT bit when enable CQE
  mmc: core: do not retry CMD6 in __mmc_switch()
  mmc: core: Convert mmc_align_data_size() into an SDIO specific function
  mmc: core: Move mmc_of_parse_voltage() to host.c
  mmc: core: Convert mmc_regulator_get_ocrmask() to static
  mmc: core: Move regulator helpers to separate file
  mmc: of_mmc_spi: Convert to mmc_of_parse_voltage()
  mmc: core: Drop retries as in-parameter to mmc_wait_for_app_cmd()
  mmc: core: Convert mmc_wait_for_app_cmd() to static
  mmc: renesas_sdhi: Change HW adjustment register according to speed mode
  mmc: mmci: Send a CMD12 to clear the DPSM at errors
  mmc: sdhci-xenon: Fixup already marked switch fall-through
  mmc: sdhci-tegra: drop ->get_ro() implementation
  mmc: sdhci-omap: drop ->get_ro() implementation
  mmc: sdhci: use WP GPIO in sdhci_check_ro()
  mmc: wmt-sdmmc: Drop unused include
  ...

Pull i3c updates from Boris Brezillon:

 - Add a /* fall-through */ comment in the dw-i3c-master driver

 - Update the I3C entries in MAINTAINERS to add an IRC chan

* tag 'i3c/for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
  i3c: master: dw-i3c-master: mark expected switch fall-through
  MAINTAINERS: Add an IRC channel for the I3C subsystem

Pull MTD updates from Boris Brezillon:
 "Core MTD changes:
   - Use struct_size() where appropriate
   - mtd_{read,write}() as wrappers around mtd_{read,write}_oob()
   - Fix misuse of PTR_ERR() in docg3
   - Coding style improvements in mtdcore.c

  SPI NOR changes:
    Core changes:
     - Add support of octal mode I/O transfer
     - Add a bunch of SPI NOR entries to the flash_info table

    SPI NOR controller driver changes:
     - cadence-quadspi:
        * Add support for Octal SPI controller
        * write upto 8-bytes data in STIG mode
     - mtk-quadspi:
        * rename config to a common one
        * add SNOR_HWCAPS_READ to spi_nor_hwcaps mask
     - Add Tudor as SPI-NOR co-maintainer

  NAND changes:
    NAND core changes:
     - Fourth batch of fixes/cleanup to the raw NAND core impacting
       various controller drivers (Sunxi, Marvell, MTK, TMIO, OMAP2).
     - Check the return code of nand_reset() and nand_readid_op().
     - Remove ->legacy.erase and single_erase().
     - Simplify the locking.
     - Several implicit fall through annotations.

    Raw NAND controllers drivers changes:
     - Fix various possible object reference leaks (MTK, JZ4780, Atmel)
     - ST:
        * Add support for STM32 FMC2 NAND flash controller
     - Meson:
        * Add support for Amlogic NAND flash controller
     - Denali:
        * Several cleanup patches
     - Sunxi:
        * Several cleanup patches
     - FSMC:
        * Disable NAND on remove()
        * Reset NAND timings on resume()

    SPI-NAND drivers changes:
     - Toshiba:
        * Add support for all Toshiba products.
     - Macronix:
        * Fix ECC status read.
     - Gigadevice:
        * Add support for GD5F1GQ4UExxG"

* tag 'mtd/for-5.1' of git://git.infradead.org/linux-mtd: (64 commits)
  mtd: spi-nor: Fix wrong abbreviation HWCPAS
  mtd: spi-nor: cadence-quadspi: fix spelling mistake: "Couldnt't" -> "Couldn't"
  mtd: spi-nor: Add support for en25qh64
  mtd: spi-nor: Add support for MX25V8035F
  mtd: spi-nor: Add support for EN25Q80A
  mtd: spi-nor: cadence-quadspi: Add support for Octal SPI controller
  dt-bindings: cadence-quadspi: Add new compatible for AM654 SoC
  mtd: spi-nor: split s25fl128s into s25fl128s0 and s25fl128s1
  mtd: spi-nor: cadence-quadspi: write upto 8-bytes data in STIG mode
  mtd: spi-nor: Add support for mx25u3235f
  mtd: rawnand: denali_dt: remove single anonymous clock support
  mtd: rawnand: mtk: fix possible object reference leak
  mtd: rawnand: jz4780: fix possible object reference leak
  mtd: rawnand: atmel: fix possible object reference leak
  mtd: rawnand: fsmc: Disable NAND on remove()
  mtd: rawnand: fsmc: Reset NAND timings on resume()
  mtd: spinand: Add support for GigaDevice GD5F1GQ4UExxG
  mtd: rawnand: denali: remove unused dma_addr field from denali_nand_info
  mtd: rawnand: denali: remove unused function argument 'raw'
  mtd: rawnand: denali: remove unneeded denali_reset_irq() call
  ...

Pull VFIO updates from Alex Williamson:

 - Switch mdev to generic UUID API (Andy Shevchenko)

 - Fixup platform reset include paths (Masahiro Yamada)

 - Fix usage of MINORMASK (Chengguang Xu)

 - Remove noise from duplicate spapr table unsets (Alexey Kardashevskiy)

 - Restore device state after PM reset (Alex Williamson)

 - Ensure memory translation enabled for PCI ROM access (Eric Auger)

* tag 'vfio-v5.1-rc1' of git://github.com/awilliam/linux-vfio:
  vfio_pci: Enable memory accesses before calling pci_map_rom
  vfio/pci: Restore device state on PM transition
  vfio/spapr_tce: Skip unsetting already unset table
  samples/vfio-mdev/mtty: expand minor range when registering chrdev region
  samples/vfio-mdev/mdpy: expand minor range when registering chrdev region
  samples/vfio-mdev/mbochs: expand minor range when registering chrdev region
  vfio: expand minor range when registering chrdev region
  vfio: platform: reset: fix up include directives to remove ccflags-y
  vfio-mdev: Switch to use new generic UUID API

The current implementation of splice() and tee() ignores O_NONBLOCK set
on pipe file descriptors and checks only the SPLICE_F_NONBLOCK flag for
blocking on pipe arguments.  This is inconsistent since splice()-ing
from/to non-pipe file descriptors does take O_NONBLOCK into
consideration.

Fix this by promoting O_NONBLOCK, when set on a pipe, to
SPLICE_F_NONBLOCK.

Some context for how the current implementation of splice() leads to
inconsistent behavior.  In the ongoing work[1] to add VM tracing
capability to trace-cmd we stream tracing data over named FIFOs or
vsockets from guests back to the host.

When we receive SIGINT from user to stop tracing, we set O_NONBLOCK on
the input file descriptor and set SPLICE_F_NONBLOCK for the next call to
splice().  If splice() was blocked waiting on data from the input FIFO,
after SIGINT splice() restarts with the same arguments (no
SPLICE_F_NONBLOCK) and blocks again instead of returning -EAGAIN when no
data is available.

This differs from the splice() behavior when reading from a vsocket or
when we're doing a traditional read()/write() loop (trace-cmd's
--nosplice argument).

With this patch applied we get the same behavior in all situations after
setting O_NONBLOCK which also matches the behavior of doing a
read()/write() loop instead of splice().

This change does have potential of breaking users who don't expect
EAGAIN from splice() when SPLICE_F_NONBLOCK is not set.  OTOH programs
that set O_NONBLOCK and don't anticipate EAGAIN are arguably buggy[2].

 [1] https://github.com/skaslev/trace-cmd/tree/vsock
 [2] https://github.com/torvalds/linux/blob/d47e3da1759230e394096fd742aad423c291ba48/fs/read_write.c#L1425Signed-off-by: Slavomir Kaslev <kaslevs@vmware.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>