- 27 Jul, 2011 22 commits
-
-
James Smart authored
T10 DIF Fixes - Fix the case where the SCSI Host supplies the CRC and driver to controller protection is on. - Only support T10 DIF type 1. LBA always goes in ref tag and app tag is not checked. - Change the format of the sense data passed up to the SCSI layer to match the Descriptor Format Sense Data found in SPC-4 sections 4.5.2.1 and 4.5.2.2. - Fix Slip PDE implementation. - Remove BUG() in else casein lpfc_sc_to_bg_opcodes. Signed-off-by:
Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by:
James Smart <james.smart@emulex.com> Signed-off-by:
James Bottomley <JBottomley@Parallels.com>
-
Krishna Gudipati authored
Signed-off-by:
Krishna Gudipati <kgudipat@brocade.com> Signed-off-by:
-
Krishna Gudipati authored
- Added support to enable / disable lunmasking on Brocade adapter ports. - Added support to query / clear lunmasking configuration. Signed-off-by:
-
Krishna Gudipati authored
- Added support to enable initiator based lun masking. - Initiator based Lun masking works similar to zoning where initiator port is allowed to see only those LUNs which are configured to be seen. Signed-off-by:
-
Krishna Gudipati authored
- Added dconf (Driver Config) BFA sub-module. - The dconf sub-module provides interfaces and manages flash writes to the flash DRV parition. - dconf sub-module also ensures that the whole 64K DRV partition is updated on a flash write. Signed-off-by:
-
Krishna Gudipati authored
Signed-off-by:
-
Krishna Gudipati authored
- Added support to configure QOS on Brocade adapter ports. - Added support to collect / reset QOS statistics. Signed-off-by:
-
Krishna Gudipati authored
- Added logic to enable / disable trunking on Brocade adapter ports. - Added logic to query trunking info. Signed-off-by:
-
Krishna Gudipati authored
Signed-off-by:
-
Krishna Gudipati authored
- Added support to collect and reset fcport stats. - Modified design to allow multiple requests for fcport stats. - fcport will remember the stats request in its stats_pending queue and service each of the queued requests after receiving a firmware response for the prior request. Signed-off-by: -
Krishna Gudipati authored
- Made changes to support IO profiling. - Added support to configure and query IO profiling info. Signed-off-by:
-
Krishna Gudipati authored
Extended BSG to support stats, port log and trace reset and to support adapter, port SET operations. Signed-off-by:
-
Krishna Gudipati authored
Added logic to check the loopback test input speed based on port mode. Signed-off-by:
-
Krishna Gudipati authored
- Made changes to always acknowledge RME interrupt and update consumer index (CI) when RME interrupt is generated. - Made changes to have ASIC specific hw_rspq_ack() handler. Signed-off-by:
-
Krishna Gudipati authored
Signed-off-by:
-
Krishna Gudipati authored
- Added support to post vendor unique events on fc_host. - Supports adapter, port, ioc, flash and remote port based AEN events. Signed-off-by:
-
Chandra Seetharaman authored
rdac hardware handler uses "Subsystem Identifier" from C4 inquiry page to uniquely identify a storage. The problem with that is that if any any of the bytes are non-ascii, subsys_id will all be spaces (hex 0x20). This creates lot of problems especially when there are multiple rdac storages are connected to the server. Use "Storage Array Unique Identifier" from C8 inquiry page, which is the world wide unique identifier for the storage array, to uniquely identify the storage. Signed-off-by:
Chandra Seetharaman <sekharan@us.ibm.com> Signed-off-by:
-
Kashyap, Desai authored
When READ_6 command is issued, the setting of SILI Bit in CDB is confirmed and if SILI bit is off, the processing of relavent Errata is executed. Earlier we did not have check for SILI bit in READ_6 CDB. As described in "ssc-r22", Now Driver is checking SILI bit for READ_6. Signed-off-by:
Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by:
-
Saurav Kashyap authored
Signed-off-by:
Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by:
Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by:
-
Saurav Kashyap authored
The code is changed to support the new dynamic logging infrastructure. Following are the levels added. Default is 0 - no logging. 0x40000000 - Module Init & Probe. 0x20000000 - Mailbox Cmnds. 0x10000000 - Device Discovery. 0x08000000 - IO tracing. 0x04000000 - DPC Thread. 0x02000000 - Async events. 0x01000000 - Timer routines. 0x00800000 - User space. 0x00400000 - Task Management. 0x00200000 - AER/EEH. 0x00100000 - Multi Q. 0x00080000 - P3P Specific. 0x00040000 - Virtual Port. 0x00020000 - Buffer Dump. 0x00010000 - Misc. 0x7fffffff - For enabling all logs, can be too many logs. Setting ql2xextended_error_logging module parameter to any of the above value, will enable the debug for that particular level. Do LOGICAL OR of the value to enable more than one level. Signed-off-by:
Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by:
Joe Carnuccio <joe.carnuccio@qlogic.com> Signed-off-by:
Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by:
Madhuranath Iyengar <Madhu.Iyengar@qlogic.com> Signed-off-by:
-
Saurav Kashyap authored
This patch adds the dynamic logging framework to the qla2xxx driver. The user will be able to change the logging levels on the fly i.e. without load/unload of the driver. This also enables logging to be enabled for a particular section of the driver such as initialization, device discovery etc. Signed-off-by:
-
James Smart authored
During cable pull tests on our 16G FC adapter, we are seeing errors, typically reads to close targets, which fail due to CRC or framing errors caused by the cable being pull (return status DID_ERROR). The adapter detects the error on one of the first frames received, marks the FC exchange as dead (further frames go to bit bucket) and signals the host of the error. This action is so quick, and coupled with fast host CPUs, creates a scenario in which the midlayer sees the failure and retries the io almost immediately. We've seen link traces with the retry on the link while the original i/o is still being processed by the target. We're also seeing the time window for the "link to pull-apart" and the physical interface to report disconnected to be in the few millisecond range. Which means, we're encountering scenarios where the full retry count is exhausted (all with error) by the midlayer before the link disconnect state is detected. We looked at 8G FC behavior and occasionally see the same behavior, but as the link was slower, it rarely could exhaust all retries before the link reported disconnect. What is needed is a slight delay between io retries due to DID_ERROR to cover this error. It is inappropriate to put this delay in the driver, as the error is indistinguishable from other link-related errors, nor does the driver track whether the io is a retry or not. This is also easier than tracking between-io-error bursts that are seen in this scenario. The patch below updates the retry path so that it inserts a delay as if the target was busy. The busy delay is on the order of 6ms. This delay is sufficient to ensure the link down condition is reported before the retry count is exhausted (at most 1 retry is seen). Signed-off-by:
-
- 26 Jul, 2011 18 commits
-
-
Kashyap, Desai authored
Issue: This issue is seen on LSI H/W WarpDrive SSS6200 When filed direct I/O is tried as volume I/O the scmd field in internal lookup table get cleared and because of that the retried volume I/O never gets reported as completed to SML. Result: I/O timeout and Error handling thread will kicking off Fix: Setting back the scmd in the lookup table before retrying the failed direct i/o Signed-off-by:
-
Bhanu Prakash Gollapudi authored
Signed-off-by:
Bhanu Prakash Gollapudi <bprakash@broadcom.com> Signed-off-by:
-
Hannes Reinecke authored
Currently it's impossible to find out if the host supports wide SCSI unless you're committed to trawl through syslog. And it's near impossible to find the actual HBA id, which is settable for some SCSI HBAs (like aic7xxx). So export them via sysfs. Signed-off-by:
Hannes Reinecke <hare@suse.de> Signed-off-by:
Ankit Jain <jankit@suse.de> Signed-off-by:
-
Xiangliang Yu authored
Add support for interrupt tasklet, which will improve performance. Correct spelling of "20011" [jejb: simplified ifdefs and fixed unused variable problem] Signed-off-by:
Xiangliang Yu <yuxiangl@marvell.com> Signed-off-by:
-
Xiangliang Yu authored
Remove obsolete comments and add new comments Signed-off-by:
-
Xiangliang Yu authored
Change code to match HBA datasheet. Change code to make it readable. Add support big endian for mvs_prd_imt. Add cpu_to_le32 and cpu_to_le64 to use on addr. Add scan_finished for structure mvs_prv_info. Signed-off-by:
-
Xiangliang Yu authored
Add new macros: MVS_SOFT_RESET, MVS_HARD_RESET, MVS_PHY_TUNE, MVS_COMMAND_ACTIVE, EXP_BRCT_CHG, MVS_MAX_SG Add new member sg_width in struct mvs_chip_info Use macros rather than magic number Add new functions: mvs_fill_ssp_resp_iu, mvs_set_sense, mvs_94xx_clear_srs_irq, mvs_94xx_phy_set_link_rate Signed-off-by:
-
Xiangliang Yu authored
Remove unused macros: VSR_PHY_VS0, VSR_PHY_VS1, MVS_SLOTS, MVS_CAN_QUEUE, MVS_MSI, SG_MX, _MV_DUMP, MV_DISABLE_NCQ Remove unused variables for mvs_info: irq, exp_req, cmd_size Remove unused functions: mvs_get_sas_addr, mvs_hexdump, mvs_hba_sb_dump, mvs_hab_memory_dump, mvs_hba_cq_dump Signed-off-by:
-
Xiangliang Yu authored
Fix 94xx A0/B0 revision hotplug issue. Remove unused macro: DISABLE_HOTPLUG_DMA_FIX Signed-off-by:
-
Xiangliang Yu authored
Signed-off-by:
-
Xiangliang Yu authored
Add 94xx phy tuning to aid manufacturing. Add support for 94xx multiple revisions: A0, B0, C0, C1, C2. Signed-off-by:
-
Xiangliang Yu authored
Signed-off-by:
-
Linus Torvalds authored
* Merge akpm patch series: (122 commits) drivers/connector/cn_proc.c: remove unused local Documentation/SubmitChecklist: add RCU debug config options reiserfs: use hweight_long() reiserfs: use proper little-endian bitops pnpacpi: register disabled resources drivers/rtc/rtc-tegra.c: properly initialize spinlock drivers/rtc/rtc-twl.c: check return value of twl_rtc_write_u8() in twl_rtc_set_time() drivers/rtc: add support for Qualcomm PMIC8xxx RTC drivers/rtc/rtc-s3c.c: support clock gating drivers/rtc/rtc-mpc5121.c: add support for RTC on MPC5200 init: skip calibration delay if previously done misc/eeprom: add eeprom access driver for digsy_mtc board misc/eeprom: add driver for microwire 93xx46 EEPROMs checkpatch.pl: update $logFunctions checkpatch: make utf-8 test --strict checkpatch.pl: add ability to ignore various messages checkpatch: add a "prefer __aligned" check checkpatch: validate signature styles and To: and Cc: lines checkpatch: add __rcu as a sparse modifier checkpatch: suggest using min_t or max_t ... Did this as a merge because of (trivial) conflicts in - Documentation/feature-removal-schedule.txt - arch/xtensa/include/asm/uaccess.h that were just easier to fix up in the merge than in the patch series.
-
Andrew Morton authored
Fix the warning drivers/connector/cn_proc.c: In function 'proc_ptrace_connector': drivers/connector/cn_proc.c:176: warning: unused variable 'tracer' Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Paul E. McKenney authored
There have been persistent lockdep RCU splats, indicating that submitters are not testing with CONFIG_PROVE_RCU. Add this config option to the list in Documentation/SubmitChecklist. Also add CONFIG_DEBUG_OBJECTS_RCU_HEAD for good measure. Signed-off-by:
Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by:
-
Akinobu Mita authored
Use hweight_long() to count free bits in the bitmap. Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by:
-
Akinobu Mita authored
Using __test_and_{set,clear}_bit_le() with ignoring its return value can be replaced with __{set,clear}_bit_le(). This introduces reiserfs_{set,clear}_le_bit for __{set,clear}_bit_le and does the above change with them. Signed-off-by: -
Witold Szczeponik authored
When parsing PnP ACPI resource structures, it may happen that some of the resources are disabled (in which case "the size" of the resource equals zero). The current solution is to skip these resources completely - with the unfortunate side effect that they are not registered despite the fact that they exist, after all. (The downside of this approach is that these resources cannot be used as templates for setting the actual device's resources because they are missing from the template.) The kernel's APM implementation does not suffer from this problem and registers all resources regardless of "their size". This patch fixes a problem with (at least) the vintage IBM ThinkPad 600E (and most likely also with the 600, 600X, and 770X which have a very similar layout) where some of its PnP devices support options where either an IRQ, a DMA, or an IO port is disabled. Without this patch, the devices can not be configured using the "/sys/bus/pnp/devices/*/resources" interface. The manipulation of these resources is important because the 600E has very demanding requirements. For instance, the number of IRQs is not sufficient to support all devices of the 600E. Fortunately, some of the devices, like the sound card's MPU-401 UART, can be configured to not use any IRQ, hence freeing an IRQ for a device that requires one. (Still, the device's "ResourceTemplate" requires an IRQ resource descriptor which cannot be created if the resource has not been registered in the first place.) As an example, the dependent sets of the 600E's CSC0103 device (the MPU-401 UART) are listed, with the patch applied, as: Dependent: 00 - Priority preferred port 0x300-0x330, align 0xf, size 0x4, 16-bit address decoding irq <none> High-Edge Dependent: 01 - Priority acceptable port 0x300-0x330, align 0xf, size 0x4, 16-bit address decoding irq 5,7,2/9,10,11,15 High-Edge (The same result is obtained when PNPBIOS is used instead of PnP ACPI.) Without the patch, the IRQ resource in the preferred option is not listed at all: Dependent: 00 - Priority preferred port 0x300-0x330, align 0xf, size 0x4, 16-bit address decoding Dependent: 01 - Priority acceptable port 0x300-0x330, align 0xf, size 0x4, 16-bit address decoding irq 5,7,2/9,10,11,15 High-Edge And in fact, the 600E's DSDT lists the disabled IRQ as an option, as can be seen from the following excerpt from the DSDT: Name (_PRS, ResourceTemplate () { StartDependentFn (0x00, 0x00) { IO (Decode16, 0x0300, 0x0330, 0x10, 0x04) IRQNoFlags () {} } StartDependentFn (0x01, 0x00) { IO (Decode16, 0x0300, 0x0330, 0x10, 0x04) IRQNoFlags () {5,7,9,10,11,15} } EndDependentFn () }) With this patch applied, a user space program - or maybe even the kernel - can allocate all devices' resources optimally. For the 600E, this means to find optimal resources for (at least) the serial port, the parallel port, the infrared port, the MWAVE modem, the sound card, and the MPU-401 UART. The patch applies the idea to register disabled resources to all types of resources, not just to IRQs, DMAs, and IO ports. At the same time, it mimics the behavior of the "pnp_assign_xxx" functions from "drivers/pnp/manager.c" where resources with "no size" are considered disabled. No regressions were observed on hardware that does not require this patch. The patch is applied against 2.6.39. NB: The kernel's current PnP interface does not allow for disabling individual resources using the "/sys/bus/pnp/devices/$device/resources" file. Assuming this could be done, a device could be configured to use a disabled resource using a simple series of calls: echo disable > /sys/bus/pnp/devices/$device/resources echo clear > /sys/bus/pnp/devices/$device/resources echo set irq disabled > /sys/bus/pnp/devices/$device/resources echo fill > /sys/bus/pnp/devices/$device/resources echo activate > /sys/bus/pnp/devices/$device/resources This patch addresses only the parsing of PnP ACPI devices. ChangeLog (v1 -> v2): - extend patch description - fix typo in patch itself Signed-off-by:Witold Szczeponik <Witold.Szczeponik@gmx.net> Cc: Len Brown <lenb@kernel.org> Cc: Adam Belay <abelay@mit.edu> Cc: Bjorn Helgaas <bjorn.helgaas@hp.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Cc: Matthew Garrett <mjg@redhat.com> Signed-off-by:
-
