After receiving device mac address from device, send this as
a source address for further commands instead of broadcast
address.

This will help in multi host NIC cards.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/3com/3c59x.c: In function ‘vortex_up’:
drivers/net/ethernet/3com/3c59x.c:1551:9: warning: variable
‘mii_reg1’ set but not used [-Wunused-but-set-variable]

It is never used, and so can be removed.
Signed-off-by: yu kuai <yukuai3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2020-01-07

This series adds 2 sets of changes to mlx5 driver
1) Misc updates and cleanups:

1.1) Stack usages warning cleanups and log level reduction
1.2) Increase the max number of supported rings
1.3) Support accept TC action on native NIC netdev.

2) Software steering support for multi destination steering rules:
First three patches from Erez are adding the low level FW command support
and SW steering infrastructure to create the mult-destination FW tables.

Last four patches from Alex are introducing the needed changes and APIs in
SW steering to create and manage multi-destination actions and rules.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The variable failed is being assigned a value that is never read, the
following goto statement jumps to the end of the function and variable
failed is not referenced at all.  Remove the redundant assignment.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simplify and fix the version information displayed by the driver.
The new info better relects what is needed to support the hardware.

Prev:
Version: 4.8.0, Pipeline 22169 0x4001, Rev 0, Bond 5, CSR 311, IRQ 2

New:
Version: 4.8.0, Id: 0x4001  Hw Rev: 5  OTP Config Select: 15

- Remove pipeline, CSR and IRQ because version x.y.z already incorporates
  this information.
- Remove bond number because it is not used.
- Remove rev number because register was not implemented, always 0
- Add HW Rev ID register to replace rev number
- Add OTP config select to show the user configuration chosen by
  the configurable GPIO pins on start-up
Signed-off-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The proper pointer to be passed as argument is hw
Detected using Coccinelle.

Fixes: 6517798d ("enetc: Make MDIO accessors more generic and export to include/linux/fsl")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The priv->tx_ring[] has 16 elements but only priv->num_tx_rings are
set up, the rest are NULL.  This ">" comparison should be ">=" to avoid
a potential crash.

Fixes: 0d08c9ec ("enetc: add support time specific departure base on the qos etf")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jose Abreu says:

====================
Documentation: stmmac documentation improvements

Converts stmmac documentation to RST format.

1) Adds missing entry of stmmac documentation to MAINTAINERS.

2) Converts stmmac documentation to RST format and adds some new info.

3) Adds the new RST file to the list of files.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the stmmac RST file to the index.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert the documentation of the driver to RST format and delete the old
txt and old information that no longer applies.

Also, add some new information.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the missing entry for the file that documents the stmicro Ethernet
driver stmmac.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use __func__ to print the function name instead of hard coded string.
BTW, replace printk(KERN_DEBUG, ...) with netdev_dbg.
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Chen Zhou says:

====================
net: ch9200: code cleanup

patch 1 introduce __func__ in debug message.
patch 2 remove unnecessary return.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The return is not needed, remove it.
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use __func__ to print the function name instead of hard coded string.
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shannon Nelson says:

====================
ionic: driver updates

These are a few little updates for the ionic network driver.

v2: dropped IBM msi patch
    added fix for a compiler warning
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Build checks have pointed out that 'hb' can theoretically
be used before set, so let's initialize it and get rid
of the compiler complaint.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure the NIC drops packets that are larger than the
specified MTU.

The front end of the NIC will accept packets larger than MTU and
will copy all the data it can to fill up the driver's posted
buffers - if the buffers are not long enough the packet will
then get dropped.  With the Rx SG buffers allocagted as full
pages, we are currently setting up more space than MTU size
available and end up receiving some packets that are larger
than MTU, up to the size of buffers posted.  To be sure the
NIC doesn't waste our time with oversized packets we need to
lie a little in the SG descriptor about how long is the last
SG element.

At dealloc time, we know the allocation was a page, so the
deallocation doesn't care about what length we put in the
descriptor.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a counter for packets dropped by the driver, typically
for bad size or a receive error seen by the device.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

The subdevice concept is not being used in the driver, so
drop the references to it.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Until now it was possible to pass a packet to a single destination such
as vport or flow table. With the new support if multiple vports or multiple
tables are provided as destinations, fs_dr will create a multiple
destination table action, this action should replace other destination
actions provided to mlx5dr_create_rule.
Each vport destination can be provided with a reformat actions which
will be done before forwarding the packet to the vport.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

A multiple destination table action allows HW packet duplication
to multiple destinations, this is useful for multicast or mirroring
traffic for debug. Duplicating is done using a FW flow table with
multiple destinations.

The new action creation function, mlx5dr_action_create_mult_dest_tbl
will allow creating a single table to iterate over several dr actions.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Function prefix was changed to be similar to other action APIs.
In order to support other FW tables the mlx5_flow_table struct was
replaced with table id and type.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

We need to have the flow-table flags when creation sw-steering tables,
this parameter exists in the layer between fs_core to sw_steering, this
patch gives it to the creation function.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Currently SW steering doesn't have the means to access HW iterators to
support multi-destination (FTEs) flow table entries.

In order to support multi-destination FTEs for port-mirroring, SW
steering will create a dedicated multi-destination FW managed flow table
and FTEs via direct FW commands that we introduced in the previous patch.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Implement the FW command to setup a FTE (Flow Table Entry) into the FW
managed flow tables.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Instead of using multiple variables use a simple struct. The
number of passed argument was too high after adding the encap
decap support bits arguments used for multiple destination reformat.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Use helper routines to setup and teardown multiple EQs and reuse the
code in setup, cleanup and error unwinding flows.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

In below sequence, a EQE entry arrives for a CQ which is on the path of
being destroyed.

           cpu-0               cpu-1
           ------              -----
mlx5_core_destroy_cq()      mlx5_eq_comp_int()
  mlx5_eq_del_cq()          [..]
    radix_tree_delete()     [..]
  [..]                         mlx5_eq_cq_get() /* Didn't find CQ is
                                                 * a valid case.
                                                 */
  /* destroy CQ in hw */
  mlx5_cmd_exec()

This is still a valid scenario and correct delete CQ sequence, as
mirror of the CQ create sequence.
Hence, suppress the non harmful debug message from warn to debug level.
Keep the debug log message rate limited because user application can
trigger it repeatedly.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Currently the max number of channels is limited to 64, which is half of
the indirection table size to allow some flexibility. But on servers
with more than 64 cores, users may want to utilize more queues.

This patch increases the advertised max number of channels to 128 by
changing the ratio between channels and indirection table slots to 1:1.
At the same time, the driver still enable no more than 64 channels at
loading. Users can change it by ethtool afterwards.
Signed-off-by: Fan Li <fanl@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

In one case, we may forward packets from one vport
to others, but only one packets flow will be accepted,
which destination ip was assign to VF.

+-----+     +-----+            +-----+
| VFn |     | VF1 |            | VF0 | accept
+--+--+     +--+--+  hairpin   +--^--+
   |           | <--------------- |
   |           |                  |
+--+-----------v-+             +--+-------------+
|   eswitch PF1  |             |   eswitch PF0  |
+----------------+             +----------------+

tc filter add dev $PF0 protocol all parent ffff: prio 1 handle 1 \
	flower skip_sw action mirred egress redirect dev $VF0_REP
tc filter add dev $VF0 protocol ip  parent ffff: prio 1 handle 1 \
	flower skip_sw dst_ip $VF0_IP action pass
tc filter add dev $VF0 protocol all parent ffff: prio 2 handle 2 \
	flower skip_sw action mirred egress redirect dev $VF1
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

In some configurations, gcc tries too hard to optimize this code:

drivers/net/ethernet/mellanox/mlx5/core/en_stats.c: In function 'mlx5e_grp_sw_update_stats':
drivers/net/ethernet/mellanox/mlx5/core/en_stats.c:302:1: error: the frame size of 1336 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]

As was stated in the bug report, the reason is that gcc runs into a corner
case in the register allocator that is rather hard to fix in a good way.

As there is an easy way to work around it, just add a comment and the
barrier that stops gcc from trying to overoptimize the function.

Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=92657
Cc: Adhemerval Zanella <adhemerval.zanella@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The function mlx5_buf_alloc_node is only used by the function in the
local scope. So it is appropriate to limit this function in the local
scope.
Signed-off-by: Zhu Yanjun <zyjzyj2000@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Jeff Kirsher says:

====================
1GbE Intel Wired LAN Driver Updates 2020-01-06

This series contains updates to igc to add basic support for
timestamping.

Vinicius adds basic support for timestamping and enables ptp4l/phc2sys
to work with i225 devices.  Initially, adds the ability to read and
adjust the PHC clock.  Patches 2 & 3 enable and retrieve hardware
timestamps.  Patch 4 implements the ethtool ioctl that ptp4l uses to
check what timestamping methods are supported.  Lastly, added support to
do timestamping using the "Start of Packet" signal from the PHY, which
is now supported in i225 devices.

While i225 does support multiple PTP domains, with multiple timestamping
registers, we currently only support one PTP domain and use only one of
the timestamping registers for implementation purposes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
Unique mv88e6xxx IRQ names

There are a few boards which have multiple mv88e6xxx switches. With
such boards, it can be hard to determine which interrupts belong to
which switches. Make the interrupt names unique by including the
device name in the interrupt name. For the SERDES interrupt, also
include the port number. As a result of these patches ZII devel C
looks like:

 50:          0  gpio-vf610  27 Level     mv88e6xxx-0.1:00
 54:          0  mv88e6xxx-g1   3 Edge      mv88e6xxx-0.1:00-g1-atu-prob
 56:          0  mv88e6xxx-g1   5 Edge      mv88e6xxx-0.1:00-g1-vtu-prob
 58:          0  mv88e6xxx-g1   7 Edge      mv88e6xxx-0.1:00-g2
 61:          0  mv88e6xxx-g2   1 Edge      !mdio-mux!mdio@1!switch@0!mdio:01
 62:          0  mv88e6xxx-g2   2 Edge      !mdio-mux!mdio@1!switch@0!mdio:02
 63:          0  mv88e6xxx-g2   3 Edge      !mdio-mux!mdio@1!switch@0!mdio:03
 64:          0  mv88e6xxx-g2   4 Edge      !mdio-mux!mdio@1!switch@0!mdio:04
 70:          0  mv88e6xxx-g2  10 Edge      mv88e6xxx-0.1:00-serdes-10
 75:          0  mv88e6xxx-g2  15 Edge      mv88e6xxx-0.1:00-watchdog
 76:          5  gpio-vf610  26 Level     mv88e6xxx-0.2:00
 80:          0  mv88e6xxx-g1   3 Edge      mv88e6xxx-0.2:00-g1-atu-prob
 82:          0  mv88e6xxx-g1   5 Edge      mv88e6xxx-0.2:00-g1-vtu-prob
 84:          4  mv88e6xxx-g1   7 Edge      mv88e6xxx-0.2:00-g2
 87:          2  mv88e6xxx-g2   1 Edge      !mdio-mux!mdio@2!switch@0!mdio:01
 88:          0  mv88e6xxx-g2   2 Edge      !mdio-mux!mdio@2!switch@0!mdio:02
 89:          0  mv88e6xxx-g2   3 Edge      !mdio-mux!mdio@2!switch@0!mdio:03
 90:          0  mv88e6xxx-g2   4 Edge      !mdio-mux!mdio@2!switch@0!mdio:04
 95:          3  mv88e6xxx-g2   9 Edge      mv88e6xxx-0.2:00-serdes-9
 96:          0  mv88e6xxx-g2  10 Edge      mv88e6xxx-0.2:00-serdes-10
101:          0  mv88e6xxx-g2  15 Edge      mv88e6xxx-0.2:00-watchdog

Interrupt names like !mdio-mux!mdio@2!switch@0!mdio:01 are created by
phylib for the integrated PHYs. The mv88e6xxx driver does not
determine these names.
====================
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dynamically generate a unique interrupt name for the VTU and ATU,
based on the device name.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dynamically generate a unique g2 interrupt name, based on the
device name.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dynamically generate a unique watchdog interrupt name, based on the
device name.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dynamically generate a unique SERDES interrupt name, based on the
device name and the port the SERDES is for. For example:

 95:          3  mv88e6xxx-g2   9 Edge      mv88e6xxx-0.2:00-serdes-9
 96:          0  mv88e6xxx-g2  10 Edge      mv88e6xxx-0.2:00-serdes-10

The 0.2:00 indicates the switch and -9 indicates port 9.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dynamically generate a unique switch interrupt name, based on the
device name.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>