- 19 Sep, 2009 40 commits
-
-
Alan Stern authored
This patch (as1288) fixes the initialization logic in serial_install(). A new tty always needs to have a termios initialized no matter what, not just in the case where the lower driver will override the termios settings. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Alan Stern authored
This patch (as1287) makes serial_install() be reponsible for acquiring references to the usb_serial structure and the driver module when a tty is first used. This is more sensible than having serial_open() do it, because a tty can be opened many times whereas it is installed only once, when it is created. (Not to mention that these actions are reversed when the tty is released, not when it is closed.) Finally, it is at install time that the TTY core takes its own reference to the usb_serial module, so it is only fitting that we should act the same way in regard to the lower-level serial driver. Signed-off-by:
-
Alan Stern authored
This patch (as1286) changes usb_serial_get_by_index(). Now the routine will check whether the serial device has been disconnected; if it has then the return value will be NULL. If the device hasn't been disconnected then the routine will return with serial->disc_mutex held, so that the caller can use the structure without fear of racing against driver unloads. This permits the scope of table_mutex in destroy_serial() to be reduced. Instead of protecting the entire function, it suffices to protect the part that actually uses serial_table[], i.e., the call to return_serial(). There's no longer any danger of the refcount being incremented after it reaches 0 (which was the reason for having the large scope previously), because it can't reach 0 until the serial device has been disconnected. Also, the patch makes serial_install() check that serial is non-NULL before attempting to use it. Signed-off-by:
-
Alan Stern authored
This patch (as1285) rearranges the subroutines in usb-serial.c concerned with tty lifetimes into a more logical order: install, open, hangup, close, release. It also updates the formatting of the kerneldoc comments. Signed-off-by:
-
Alan Stern authored
This patch (as1284) changes the referencing of the usb_serial and usb_serial_port structures in usb-serial.c. It's not feasible to make the port structures keep a reference to the serial structure, because the ports need to remain in existence when serial is released -- quite a few of the drivers expect this. Consequently taking a reference to the port when the device file is open is insufficient; such a reference would not pin serial. To fix this, we now take a reference to serial when the device file is opened. The final put_device() for the ports occurs in destroy_serial(), so that the ports will last as long as they are needed. The patch initializes all the port devices, including those in the unused "fake" ports. This makes the code more uniform because they can all be released in the same way. The error handling code in usb_serial_probe() is much simplified by this approach; instead of freeing everything by hand we can use a single usb_serial_put() call. Also simplified is the port-release mechanism. Instead of being two separate routines, port_release() and port_free() can be combined into one. Signed-off-by:
-
Jiri Slaby authored
In moxa specific ASPP_OQUEUE ioctl command, they apparently want only know whether there is space in transmitter hold register. So switch UART_LSR_TEMT to UART_LSR_THRE in that specific case according to the change in 1.14 moxa drivers. Signed-off-by:
Jiri Slaby <jirislaby@gmail.com> Signed-off-by:
-
Jiri Slaby authored
Add support for MOXA:0x1120 pci device. It's a 2-port device and differs in no way from the others. So this turns out to be a trivial pci_device_id change. Increase also the version number. Signed-off-by:
-
Peter Korsgaard authored
Adapt isr to work with shared interrupt lines. Signed-off-by:
Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by:
-
Jiri Slaby authored
Stanse found a tty refcnt leak in read_int_callback. In fact it's handled wrong altogether. tty_port_tty_get can return NULL and it's not checked in that manner. Fix that by checking the tty_port_tty_get retval and put tty kref properly. http://stanse.fi.muni.cz/Signed-off-by:
-
Jiri Slaby authored
Stanse found a tty refcnt leak on one fail path in rc_transmit. Fix that by jumping to the 'out' label. http://stanse.fi.muni.cz/Signed-off-by:
-
Jiri Slaby authored
tty_port_ops.shutdown takes only one parameter: tty port. Remove the second one and use port->tty where needed instead. Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Alan Stern authored
This patch (as1282) fixes some obvious typos in the TTY core. Signed-off-by:
-
Jiri Slaby authored
vt_waitactive no longer accepts console parameter as console-1 since commit "vt: add an event interface". It expects console number directly (as viewed by userspace -- counting from 1). Fix a deadlock suspend regression by redefining adding one to vt in vt_move_to_console. Signed-off-by:
-
Marcin Slusarz authored
Signed-off-by:
Marcin Slusarz <marcin.slusarz@gmail.com> Signed-off-by:
-
Arnd Bergmann authored
The VT specific compat_ioctl handlers are the only ones in common code that require the BKL. Moving them into the vt driver lets us remove the BKL from the other handlers and cleans up the code. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Joe Peterson authored
Check L_ECHOCTL before insertting a character in the echo buffer (rather than as the buffer is processed), to be more consistent with when all other L_ flags are checked. Also cleaned up the related logic. Note that this and the previous patch ("n_tty: honor opost flag for echoes") were verified together by the reporters of the bug that patch addresses (http://bugs.linuxbase.org/show_bug.cgi?id=2692), and the test now passes. Signed-off-by:Joe Peterson <joe@skyrush.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Joe Peterson authored
Fixes the following bug: http://bugs.linuxbase.org/show_bug.cgi?id=2692 Causes processing of echoed characters (output from the echo buffer) to honor the O_OPOST flag, which is consistent with the old behavior. Note that this and the next patch ("n_tty: move echoctl check and clean up logic") were verified together by the bug reporters, and the test now passes. Signed-off-by: -
Alan Cox authored
Various drivers have hacks to mangle termios structures. This stems from the fact there is no nice setup hook for configuring the termios settings when the port is created Signed-off-by:
Alan Cox <alan@linux.intel.com> Signed-off-by:
-
Deepak Saxena authored
Commit b5b82df6, from May 2007, breaks no_console_suspend on the OLPC XO laptop. Basically what happens is that upon returning from resume, serial8250_resume_port() will reconfigure the port for high speed mode and all console output will be garbled, making debug of the resume path painful. This patch modifies uart_resume_port() to reset the port to the state it was in before we suspended. Original patch by Marcelo Tosatti Second patch by Deepak then reworked by Alan to fit with the tty changes before it got submitted. Also fixed the console path to set c_i/ospeed as some drivers require the termios fields are valid Signed-off-by:
Deepak Saxena <dsaxena@laptop.org> Signed-off-by:
-
Alan Cox authored
Initially just use the helper and thus krefs when we set and clear the port values. Signed-off-by: -
Alan Cox authored
The serial layer for some reason uses different defines for the special case close delays and then conditionally switches to/from the normal ones in the ioctls. Remove this rather pointless abstraction Signed-off-by:
-
Alan Cox authored
This little helper is now tty_port specific and useful generally so move it Signed-off-by:
-
Alan Cox authored
This is used by various drivers not just serial and can be extracted as commonality Signed-off-by: -
Alan Cox authored
They cover essentially the same stuff and we can therefore fold it into the tty_port one. Signed-off-by:
-
Alan Cox authored
This typedef is now extinct Signed-off-by:
-
Alan Cox authored
Fortunately the serial layer was designed to use the same flag values but with different names. It has its own SUSPENDED flag which is a free slot in the ASYNC flags so we allocate it in the ASYNC flags instead. Signed-off-by:
-
Alan Cox authored
Remove more stuff from the serial special case code Signed-off-by:
-
Alan Cox authored
Extract out a lot of the x.port. uses and also show up where there are things left to be isolated that prevent use using the port helpers in the serial layer at this point Signed-off-by: -
Alan Cox authored
Remove some more serial specific use Signed-off-by:
-
Alan Cox authored
We moved this into uart_state, now move the fields out of the separate structure and kill it off. Signed-off-by:
-
Alan Cox authored
Again moving towards being able to add a common open method Signed-off-by: -
Alan Cox authored
And indeed none of them use it. Clean this up as it will make moving to a standard open method rather easier. Signed-off-by:
-
Alan Cox authored
X and other graphical interfaces need to be able to flip to a console and lock it into graphics mode without races. Signed-off-by:
-
Alan Cox authored
We have vt_kern.h for this Signed-off-by:
-
Alan Cox authored
In the past someone gratuitiously borrowed chunks of kernel internal vt code and dumped them in kernel/power. They have all sorts of deep relations with the vt code so put them in the vt tree instead Signed-off-by:
-
Alan Cox authored
This is needed and requested in various forms for ConsoleKit, screenblank handling and the like so do the job with a single interface. Also build the interface so that unlike VT_WAITACTIVE and friends it won't miss events. FIXME: Should this be a waitactive ioctl or a new device file you can poll and read events from. We need the code anyway to fix up the existing broken wait for console switch logic but the ConsoleKit people would prefer the new device to the ioctl we have here Signed-off-by:
-
Alan Cox authored
Signed-off-by:
-
Alan Cox authored
These are handled by the tty_port core code which will raise and lower the carrier correctly in tty_wait_until_ready Signed-off-by:
-
Alan Cox authored
The USB layer uses tty_hangup to deal with unplugs of the physical hardware (analogous to loss of carrier) and then frees the resources. However the tty_hangup is asynchronous. As the hangup can sleep we can use tty_vhangup which is the non async version to avoid freeing resources too early. Signed-off-by:
-
Alan Cox authored
This changed in 2006 so its about time the ACM driver caught up Signed-off-by:
-
