When we come out of system suspend state (S3) the tsadc will have been
reset and back at its default state.  While reprogramming the tsadc
it's possible that we'll glitch the output and unintentionally cause
the "over temperature" GPIO to be asserted.  Since the over
temperature GPIO is often hooked up to something that will cause a
reboot or shutdown in hardware, this glitch can be catastrophic on
some boards.

We'll add support for selecting the "sleep" pinctrl state at suspend
time.  Boards can use this to effectively disable the tsadc at suspend
time and avoid glitches when the system is resumed.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

The "init" pinctrl is defined we'll set
pinctrl to this state before probe and then "default" after probe.
Add the "init" and "sleep" pinctrl as the OTP gpio state, since we need
switch the pin to gpio state before the TSADC controller is reset.

AFAIK, the TSADC controller is reset, the tshut polarity will be
a *low* signal in a short period of time for some devices.

Says:
The TSADC get the temperature on rockchip thermal.

If T(current temperature) < (setting temperature), the OTP output the
*high* signal.
If T(current temperature) > (setting temperature), the OTP output the
*low* Signal.

In some cases, the OTP pin is connected to the PMIC, maybe the
PMIC can accept the reset response time to avoid this issue.

In other words, the system will be always reboot if we make the
OTP pin is connected the others IC to control the power.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

The prototype of do_div() is:

uint32_t do_div(uint64_t *n, uint32_t base);

Make power u64 to avoid the following warning:

   drivers/thermal/devfreq_cooling.c: In function 'get_dynamic_power':
   drivers/thermal/devfreq_cooling.c:267:2: warning: comparison of distinct pointer types lacks a cast [enabled by default]
   drivers/thermal/devfreq_cooling.c:267:2: warning: right shift count >= width of type [enabled by default]
   drivers/thermal/devfreq_cooling.c:267:2: warning: passing argument 1 of '__div64_32' from incompatible pointer type [enabled by default]
   include/asm-generic/div64.h:35:17: note: expected 'uint64_t *' but argument is of type 'long unsigned int *'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Be consistent with what other cooling devices do and return a struct
thermal_cooling_device * on register.  Also, for the unregister, accept
a struct thermal_cooling_device * as parameter.

Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

We recently changed this from unsigned long to int so it introduced an
underflow bug.

Fixes: 17e8351a ('thermal: consistently use int for temperatures')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Update the coefficients so the calculation will not overrun the
unsigned long 32bits boundary
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Victor Axelrod <victora@marvell.com>
Reviewed-by: Neta Zur Hershkovits <neta@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

The irq handler should be registered after the tempmon
module has been initialized in a known state and the
thermal_zone and cpu_cooling device have been registered
successfully. Otherwise, if the irq is triggled earlier
before thermal probe has been finished, it may lead to
'NULL' pointer kernel panic.
Signed-off-by: Bai Ping <b51503@freescale.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

When requested thermal shutdown signal polarity is low we need to make
sure that the bit representing high level of signal is reset, and not
set all other bits in that register.

Also rename TSADCV2_INT_PD_CLEAR to TSADCV2_INT_PD_CLEAR_MASK to better
reflect its nature.
Acked-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

We attempted to signal invalid code by returning -EAGAIN from
rk_tsadcv2_code_to_temp(), unfortunately the return value was stuffed
directly into the temperature pointer, potentially confusing upper
layers with temperature of -EINVAL.

Let's split temperature from error/success indicator to avoid such
confusion.

Also change the way we scan the temperature table to start with the 2nd
element so that we do not need to worry that we may reference out of
bounds element while doing binary search and keep checking that we end
up with 'mid' equal to 0 (since we are looking for the temperature that
would fall into interval between the 'mid' and 'mid - 1') .
Tested-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Tracing is useful for debugging and performance tuning.  Add similar
traces to what's present in the cpu cooling device.

Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Add a generic thermal cooling device for devfreq, that is similar to
cpu_cooling.

The device must use devfreq.  In order to use the power extension of the
cooling device, it must have registered its OPPs using the OPP library.

Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Ørjan Eide <orjan.eide@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

The OPP library is now used for power models to calculate the power
that a device would consume at a specific OPP.  To do that, we use a
simple power model which takes frequency and voltage as inputs.  We get
the voltage and frequency from the OPP library.

The devfreq cooling device for the thermal framework controls
temperature by disabling OPPs.  The power model needs to calculate the
power that would be consumed if we reenabled the OPP.  Therefore, let
dev_pm_opp_get_voltage() work for disabled OPPs.

Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Add OMAP36xx support to ti-soc-thermal driver. This
chip is also unreliable. The data provided here is
based on OMAP36xx TRM:
http://www.ti.com/lit/ug/swpu177aa/swpu177aa.pdfSigned-off-by: Eduardo Valentin <edubezva@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

This adds support for OMAP3 chips to ti-soc-thermal. As requested by
TI people, it is marked unreliable and warning is printed.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>

Pull arch/tile bugfix from Chris Metcalf:
 "This fixes a bug in 'make allmodconfig'"

* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
  tile: fix build failure

When building with allmodconfig the build was failing with the error:

arch/tile/kernel/usb.c:70:1: warning: data definition has no type or storage class [enabled by default]
arch/tile/kernel/usb.c:70:1: error: type defaults to 'int' in declaration of 'arch_initcall' [-Werror=implicit-int]
arch/tile/kernel/usb.c:70:1: warning: parameter names (without types) in function declaration [enabled by default]
arch/tile/kernel/usb.c:63:19: warning: 'tilegx_usb_init' defined but not used [-Wunused-function]

Include linux/module.h to resolve the build failure.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>

Pull MIPS fixes from Ralf Baechle:
 - Properly setup irq handling for ATH79 platforms
 - Fix bootmem mapstart calculation for contiguous maps
 - Handle little endian and older CPUs correct in BPF
 - Fix console for Fulong 2E systems
 - Handle FTLB correctly on R6 CPUs
 - Fixes for CM, GIC and MAAR support code

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Initialise MAARs on secondary CPUs
  MIPS: print MAAR configuration during boot
  MIPS: mm: compile maar_init unconditionally
  irqchip: mips-gic: Fix pending & mask reads for MIPS64 with 32b GIC.
  irqchip: mips-gic: Convert CPU numbers to VP IDs.
  MIPS: CM: Provide a function to map from CPU to VP ID.
  MIPS: Fix FTLB detection for R6
  MIPS: cpu-features: Add cpu_has_ftlb
  MIPS: ATH79: Add irq chip ar7240-misc-intc
  MIPS: ATH79: Set missing irq ack handler for ar7100-misc-intc irq chip
  MIPS: BPF: Fix build on pre-R2 little endian CPUs
  MIPS: BPF: Avoid unreachable code on little endian
  MIPS: bootmem: Fix mapstart calculation for contiguous maps
  MIPS: Fix console output for Fulong2e system

Pull perf fixes from Thomas Gleixner:
 "Another pile of fixes for perf:

   - Plug overflows and races in the core code

   - Sanitize the flow of the perf syscall so we error out before
     handling the more complex and hard to undo setups

   - Improve and fix Broadwell and Skylake hardware support

   - Revert a fix which broke what it tried to fix in perf tools

   - A couple of smaller fixes in various places of perf tools"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf tools: Fix copying of /proc/kcore
  perf intel-pt: Remove no_force_psb from documentation
  perf probe: Use existing routine to look for a kernel module by dso->short_name
  perf/x86: Change test_aperfmperf() and test_intel() to static
  tools lib traceevent: Fix string handling in heterogeneous arch environments
  perf record: Avoid infinite loop at buildid processing with no samples
  perf: Fix races in computing the header sizes
  perf: Fix u16 overflows
  perf: Restructure perf syscall point of no return
  perf/x86/intel: Fix Skylake FRONTEND MSR extrareg mask
  perf/x86/intel/pebs: Add PEBS frontend profiling for Skylake
  perf/x86/intel: Make the CYCLE_ACTIVITY.* constraint on Broadwell more specific
  perf tools: Bool functions shouldn't return -1
  tools build: Add test for presence of __get_cpuid() gcc builtin
  tools build: Add test for presence of numa_num_possible_cpus() in libnuma
  Revert "perf symbols: Fix mismatched declarations for elf_getphdrnum"
  perf stat: Fix per-pkg event reporting bug

Pull scheduler fix from Thomas Gleixner:
 "A single bug fix for the scheduler to prevent dequeueing of the idle
  task when setting the cpus allowed mask"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Fix crash trying to dequeue/enqueue the idle thread

Pull locking fix from Thomas Gleixner:
 "A single bugfix for lockdep to preserve the pinning counter when
  rebuilding the lock stack"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/lockdep: Fix hlock->pin_count reset on lock stack rebuilds

MAARs should be initialised on each CPU (or rather, core) in the system
in order to achieve consistent behaviour & performance. Previously they
have only been initialised on the boot CPU which leads to performance
problems if tasks are later scheduled on a secondary CPU, particularly
if those tasks make use of unaligned vector accesses where some CPUs
don't handle any cases in hardware for non-speculative memory regions.
Fix this by recording the MAAR configuration from the boot CPU and
applying it to secondary CPUs as part of their bringup.
Reported-by: Doug Gilmore <doug.gilmore@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: David Hildenbrand <dahi@linux.vnet.ibm.com>
Cc: linux-kernel@vger.kernel.org
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Hemmo Nieminen <hemmo.nieminen@iki.fi>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11239/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Verifying that the MAAR configuration is as expected is useful when
debugging the performance of a system. Print out the memory regions
configured via MAAR along with their attributes.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: David Hildenbrand <dahi@linux.vnet.ibm.com>
Cc: linux-kernel@vger.kernel.org
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11238/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

maar_init was previously only compiled when CONFIG_NEED_MULTIPLE_NODES
was not set, which has been fine since it is only called from the
standard implementation of mem_init which has the same condition. In
preparation for calling it from the SMP startup code on secondary CPUs,
move maar_init outside of the #ifndef such that it is always compiled.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: David Hildenbrand <dahi@linux.vnet.ibm.com>
Cc: linux-kernel@vger.kernel.org
Cc: Ingo Molnar <mingo@kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/11237/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

gic_handle_shared_int reads the GIC interrupt pending & mask registers
directly into a bitmap, which is defined as an array of unsigned longs.
The GIC pending registers may be 32 bits wide if the CM is older than
CM3, regardless of the bit width of the CPU, but for MIPS64 kernels
the unsigned longs in the bitmap will be 64 bits wide. In this case we
need to perform 2 x 32 bit reads per 64 bit unsigned long in order to
avoid missing interrupts.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11213/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Make use of the mips_cm_vp_id function to convert from Linux CPU numbers
to the VP IDs used by hardware, which are not identical in all systems.
Without doing so we map interrupts to incorrect VP(E)s.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11212/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The VP ID of a given CPU may not match up with the CPU number used by
Linux. For example, if the width of the VP part of the VP ID is wider
than log2(number of VPs per core) and the system has multiple cores then
this will be the case. Alternatively, if a pre-r6 system implements the
MT ASE with multiple VPEs per core and Linux is built without support
for the MT ASE then the numbers won't match up either. Provide a
function to convert from CPU number to VP ID.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11211/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Pull x86 fixes from Thomas Gleixner:
 "Two bugfixes from Andy addressing at least some of the subtle NMI
  related wreckage which has been reported by Sasha Levin"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/nmi/64: Fix a paravirt stack-clobbering bug in the NMI code
  x86/paravirt: Replace the paravirt nop with a bona fide empty function

Pull irq fix from Thomass Gleixner:
 "A bugfix for the atmel aic5 irq chip driver which caches the wrong
  data and thereby breaking resume"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/atmel-aic5: Use per chip mask caches in mask/unmask()

Pull ARM fixes from Russell King:
 "Just two fixes: wire up the new system calls added during the last
  merge window, and fix another user access site"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: alignment: fix alignment handling for uaccess changes
  ARM: wire up new syscalls

Pull ARM SoC fixes from Olof Johansson:
 "Our first real batch of fixes this release cycle.  Nothing really
  concerning, and diffstat is a bit inflated due to some DT contents
  moving around on STi platforms.

  There's a collection of them here:

   - A fixup for a build breakage that hits on arm64 allmodconfig in
     QCOM SCM firmware drivers
   - MMC fixes for OMAP that had quite a bit of breakage this merge
     window.
   - Misc build/warning fixes on PXA and OMAP
   - A couple of minor fixes for Beagleboard X15 which is now starting
     to see a few more users in the wild"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
  ARM: sti: dt: adapt DT to fix probe/bind issues in DRM driver
  ARM: dts: fix omap2+ address translation for pbias
  firmware: qcom: scm: Add function stubs for ARM64
  ARM: dts: am57xx-beagle-x15: use palmas-usb for USB2
  ARM: omap2plus_defconfig: enable GPIO_PCA953X
  ARM: dts: omap5-uevm.dts: fix i2c5 pinctrl offsets
  ARM: OMAP2+: AM43XX: Enable autoidle for clks in am43xx_init_late
  ARM: dts: am57xx-beagle-x15: Update Phy supplies
  ARM: pxa: balloon3: Fix build error
  ARM: dts: Fixup model name for HP t410 dts
  ARM: dts: DRA7: fix a typo in ethernet
  ARM: omap2plus_defconfig: make PCF857x built-in
  ARM: dts: Use ti,pbias compatible string for pbias
  ARM: OMAP5: Cleanup options for SoC only build
  ARM: DRA7: Select missing options for SoC only build
  ARM: OMAP2+: board-generic: Remove stale of_irq macros
  ARM: OMAP4+: PM: erratum is used by OMAP5 and DRA7 as well
  ARM: dts: omap3-igep: Move eth IRQ pinmux to IGEPv2 common dtsi
  ARM: dts: am57xx-beagle-x15: Add wakeup irq for mcp79410
  ARM: dts: am335x-phycore-som: Fix mpu voltage
  ...

Pull CIFS fixes from Steve French:
 "Four fixes from testing at the recent SMB3 Plugfest including two
  important authentication ones (one fixes authentication problems to
  some popular servers when clock times differ more than two hours
  between systems, the other fixes Kerberos authentication for SMB3)"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  fix encryption error checks on mount
  [SMB3] Fix sec=krb5 on smb3 mounts
  cifs: use server timestamp for ntlmv2 authentication
  disabling oplocks/leases via module parm enable_oplocks broken for SMB3

ARM: pxa: fixes for v4.3

These fixes are mainly regression fixes triggered by irq changes,
common clock framework introduction and sound side-effect of
other platforms.

* tag 'pxa-fixes-v4.3' of https://github.com/rjarzmik/linux:
  ARM: pxa: balloon3: Fix build error
  ARM: pxa: ssp: Fix build error by removing originally incorrect DT binding
  ARM: pxa: fix DFI bus lockups on startup
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v4.3/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Fixes for omaps for v4.3-rc cycle:

- Two more patches to fix most of the MMC regressions with the
  PBIAS regulator changes. At least two MMC driver related issues
  still seems to remain for omap3 legacy booting and omap4 duovero.
  Note that the dts changes depend on a recent regulator fix, and
  are based on the regulator commit now in mainline kernel

- Enable autoidle for am43xx clocks to prevent clocks from staying
  always on

- Fix i2c5 pinctrl offsets for omap5-uevm

- Enable PCA953X as that's needed for HDMI to work on omap5

- Update phy supplies for beagle x15 beta board

- Use palmas-usb for on beagle x15 to start using the related
  driver that recently got merged

* tag 'omap-for-v4.3/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: fix omap2+ address translation for pbias
  ARM: dts: am57xx-beagle-x15: use palmas-usb for USB2
  ARM: omap2plus_defconfig: enable GPIO_PCA953X
  ARM: dts: omap5-uevm.dts: fix i2c5 pinctrl offsets
  ARM: OMAP2+: AM43XX: Enable autoidle for clks in am43xx_init_late
  ARM: dts: am57xx-beagle-x15: Update Phy supplies
  regulator: pbias: program pbias register offset in pbias driver
  ARM: omap2plus_defconfig: Enable MUSB DMA support
  ARM: DRA752: Add ID detect for ES2.0
  ARM: OMAP3: vc: fix 'or' always true warning
  ARM: OMAP2+: Fix booting if no timer parent clock is available
  ARM: OMAP2+: omap-device: fix race deferred probe of omap_hsmmc vs omap_device_late_init
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull crypto fixes from Herbert Xu:
 "This fixes the following issues:

   - check the return value of platform_get_irq as signed int in xgene.

   - skip adf_dev_restore on virtual functions in qat.

   - fix double-free with backlogged requests in marvell_cesa"

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  hwrng: xgene - fix handling platform_get_irq
  crypto: qat - VF should never trigger SBR on PH
  crypto: marvell - properly handle CRYPTO_TFM_REQ_MAY_BACKLOG-flagged requests

Pull SCSI target fixes from Nicholas Bellinger:
 "This includes a iser-target series from Jenny + Sagi @ Mellanox that
  addresses the few remaining active I/O shutdown bugs, along with a
  patch to support zero-copy for immediate data payloads that gives a
  nice performance improvement for small block WRITEs.

  Also included are some recent >= v4.2 regression bug-fixes.  The most
  notable is a RCU conversion regression for SPC-3 PR registrations, and
  recent removal of obsolete RFC-3720 markers that introduced a login
  regression bug with MSFT iSCSI initiators.

  Thanks to everyone who has been testing + reporting bugs for v4.x"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  iscsi-target: Avoid OFMarker + IFMarker negotiation
  target: Make TCM_WRITE_PROTECT failure honor D_SENSE bit
  target: Fix target_sense_desc_format NULL pointer dereference
  target: Propigate backend read-only to core_tpg_add_lun
  target: Fix PR registration + APTPL RCU conversion regression
  iser-target: Skip data copy if all the command data comes as immediate
  iser-target: Change the recv buffers posting logic
  iser-target: Fix pending connections handling in target stack shutdown sequnce
  iser-target: Remove np_ prefix from isert_np members
  iser-target: Remove unused variables
  iser-target: Put the reference on commands waiting for unsol data
  iser-target: remove command with state ISTATE_REMOVE

Pull USB fixes from Greg KH:
 "Here are some USB driver fixes for 4.3-rc3.

  There's the usual assortment of new device ids, combined with xhci and
  gadget driver fixes.  Full details in the shortlog.  All of these have
  been in linux-next with no reported problems"

* tag 'usb-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (34 commits)
  MAINTAINERS: remove amd5536udc USB gadget driver maintainer
  USB: whiteheat: fix potential null-deref at probe
  xhci: init command timeout timer earlier to avoid deleting it uninitialized
  xhci: change xhci 1.0 only restrictions to support xhci 1.1
  usb: xhci: exit early in xhci_setup_device() if we're halted or dying
  usb: xhci: stop everything on the first call to xhci_stop
  usb: xhci: Clear XHCI_STATE_DYING on start
  usb: xhci: lock mutex on xhci_stop
  xhci: Move xhci_pme_quirk() behind #ifdef CONFIG_PM
  xhci: give command abortion one more chance before killing xhci
  usb: Use the USB_SS_MULT() macro to get the burst multiplier.
  usb: dwc3: gadget: Fix BUG in RT config
  usb: musb: fix cppi channel teardown for isoch transfer
  usb: phy: isp1301: Export I2C module alias information
  usb: gadget: drop null test before destroy functions
  usb: gadget: dummy_hcd: in transfer(), return data sent, not limit
  usb: gadget: dummy_hcd: fix rescan logic for transfer
  usb: gadget: dummy_hcd: fix unneeded else-if condition
  usb: gadget: dummy_hcd: emulate sending zlp in packet logic
  usb: musb: dsps: fix polling in device-only mode
  ...

Pull serial driver fix from Greg KH:
 "Here is one serial driver fix for 4.3-rc3 that resolves a module
  loading issue due to splitting up of the 8250 driver into smaller
  pieces.  It's been in linux-next with no reported problems"

* tag 'tty-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: serial: Add missing module license for 8250_base.ko

Pull staging driver fixes from Greg KH:
 "Here are some tiny staging driver and documentation fixes for 4.3-rc3.

  All of these resolve reported issues that people have found and have
  been in the linux-next tree for a while with no problems"

* tag 'staging-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  MAINTAINERS: Update email address for Martyn Welch
  staging: ion: fix corruption of ion_import_dma_buf
  staging: dgap: Remove myself from the MAINTAINERS file
  staging: most: Add dependency to HAS_IOMEM
  staging: unisys: remove reference of visorutil
  staging: unisys: visornic: handle error return from device registration
  staging: unisys: stop device registration before visorbus registration
  staging: unisys: visorbus: Unregister driver on error
  staging: unisys: visornic: Fix receive bytes statistics
  staging: unisys: unregister netdev when create debugfs fails
  staging: fbtft: replace master->setup() with spi_setup()
  staging: fbtft: fix 9-bit SPI support detection
  staging/lustre: change Lustre URLs and mailing list
  staging/android: Update ION TODO per LPC discussion
  Staging: most: MOST and MOSTCORE should depend on HAS_DMA
  staging: most: fix HDM_USB dependencies and build errors

Pull driver core fix from Greg KH:
 "Here is one driver core fix for 4.3-rc3 that resolves a reported oops"

* tag 'driver-core-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  cpu/cacheinfo: Fix teardown path