We have to use mdb and port entries when sending mdb notifications in
order to fill in all group attributes properly. Before this change we
would've used a fake br_mdb_entry struct to fill in only partial
information about the mdb. Now we can also reuse the mdb dump fill
function and thus have only a single central place which fills the mdb
attributes.

v3: add IPv6 support
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This change is in preparation for using the mdb port group entries when
sending a notification, so their full state and additional attributes can
be filled in.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

We need to be able to retransmit group-specific and group-and-source
specific queries. The new timer takes care of those.

v3: add IPv6 support
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Allows br_multicast_alloc_query to build queries with the port group's
source lists and sends a query for sources over and under lmqt when
necessary as per RFCs 3376 and 3810 with the suppress flag set
appropriately.

v3: add IPv6 support
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Support per port group src list (address and timer) and filter mode
dumping. Protected by either multicast_lock or rcu.

v3: add IPv6 support
v2: require RCU or multicast_lock to traverse src groups
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Initial functions for group source lists which are needed for IGMPv3
and MLDv2 include/exclude lists. Both IPv4 and IPv6 sources are supported.
User-added mdb entries are created with exclude filter mode, we can
extend that later to allow user-supplied mode. When group src entries
are deleted, they're freed from a workqueue to make sure their timers
are not still running. Source entries are protected by the multicast_lock
and rcu. The number of src groups per port group is limited to 32.

v4: use the new port group del function directly
    add igmpv2/mldv1 bool to denote if the entry was added in those
    modes, it will later replace the old update_timer bool
v3: add IPv6 support
v2: allow src groups to be traversed under rcu
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In order to avoid future errors and reduce code duplication we should
factor out the port group del sequence. This allows us to have one
function which takes care of all details when removing a port group.

v4: set pg's fast leave flag when deleting due to fast leave
    move the patch before adding source lists
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Before this patch we'd need 2 cache lines for fast-path, now all used
fields are in the first cache line.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This switches the RTL8366RB over to using phylink callbacks
instead of .adjust_link(). This is a pretty template
switchover. All we adjust is the CPU port so that is why
the code only inspects this port.

We enhance by adding proper error messages, also disabling
the CPU port on the way down and moving dev_info() to
dev_dbg().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In the commit fdeba99b
("tipc: fix use-after-free in tipc_bcast_get_mode"), we're trying
to make sure the tipc_net_finalize_work work item finished if it
enqueued. But calling flush_scheduled_work() is not just affecting
above work item but either any scheduled work. This has turned out
to be overkill and caused to deadlock as syzbot reported:

======================================================
WARNING: possible circular locking dependency detected
5.9.0-rc2-next-20200828-syzkaller #0 Not tainted
------------------------------------------------------
kworker/u4:6/349 is trying to acquire lock:
ffff8880aa063d38 ((wq_completion)events){+.+.}-{0:0}, at: flush_workqueue+0xe1/0x13e0 kernel/workqueue.c:2777

but task is already holding lock:
ffffffff8a879430 (pernet_ops_rwsem){++++}-{3:3}, at: cleanup_net+0x9b/0xb10 net/core/net_namespace.c:565

[...]
 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(pernet_ops_rwsem);
                               lock(&sb->s_type->i_mutex_key#13);
                               lock(pernet_ops_rwsem);
  lock((wq_completion)events);

 *** DEADLOCK ***
[...]

v1:
To fix the original issue, we replace above calling by introducing
a bit flag. When a namespace cleaned-up, bit flag is set to zero and:
- tipc_net_finalize functionial just does return immediately.
- tipc_net_finalize_work does not enqueue into the scheduled work queue.

v2:
Use cancel_work_sync() helper to make sure ONLY the
tipc_net_finalize_work() stopped before releasing bcbase object.

Reported-by: syzbot+d5aa7e0385f6a5d0f4fd@syzkaller.appspotmail.com
Fixes: fdeba99b ("tipc: fix use-after-free in tipc_bcast_get_mode")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Hoang Huu Le <hoang.h.le@dektech.com.au>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The wrappers in include/linux/pci-dma-compat.h should go away.

The patch has been generated with the coccinelle script below and has been
hand modified to replace GFP_ with a correct flag.
It has been compile tested.

When memory is allocated in 'vnic_dev_classifier()', 'vnic_dev_fw_info()',
'vnic_dev_notify_set()' and 'vnic_dev_stats_dump()' (vnic_dev.c) GFP_ATOMIC
must be used because its callers take a spinlock before calling these
functions.

When memory is allocated in '__enic_set_rsskey()' and 'enic_set_rsscpu()'
GFP_ATOMIC must be used because they can be called with a spinlock.
The call chain is:
  enic_reset                         <-- takes 'enic->enic_api_lock'
    --> enic_set_rss_nic_cfg
      --> enic_set_rsskey
        --> __enic_set_rsskey        <-- uses dma_alloc_coherent
      --> enic_set_rsscpu            <-- uses dma_alloc_coherent

When memory is allocated in 'vnic_dev_init_prov2()' GFP_ATOMIC must be used
because a spinlock is hidden in the ENIC_DEVCMD_PROXY_BY_INDEX macro, when
this function is called in 'enic_set_port_profile()'.

When memory is allocated in 'vnic_dev_alloc_desc_ring()' GFP_KERNEL can be
used because it is only called from 5 functions ('vnic_dev_init_devcmd2()',
'vnic_cq_alloc()', 'vnic_rq_alloc()', 'vnic_wq_alloc()' and
'enic_wq_devcmd2_alloc()'.

  'vnic_dev_init_devcmd2()': already uses GFP_KERNEL and no lock is taken
     in the between.
  'enic_wq_devcmd2_alloc()': is called from ' vnic_dev_init_devcmd2()'
     which already uses GFP_KERNEL and no lock is taken in the between.
  'vnic_cq_alloc()', 'vnic_rq_alloc()', 'vnic_wq_alloc()': are called
     from 'enic_alloc_vnic_resources()'
'enic_alloc_vnic_resources()' has only 2 call chains:

  1) enic_probe
      --> enic_dev_init
        --> enic_alloc_vnic_resources
'enic_probe()' is a probe function and no lock is taken in the between

  2) enic_set_ringparam
      --> enic_alloc_vnic_resources
'enic_set_ringparam()' is a .set_ringparam function (see struct
ethtool_ops). It seems to only take a mutex and no spinlock.

So all paths are safe to use GFP_KERNEL.

@@
@@
-    PCI_DMA_BIDIRECTIONAL
+    DMA_BIDIRECTIONAL

@@
@@
-    PCI_DMA_TODEVICE
+    DMA_TO_DEVICE

@@
@@
-    PCI_DMA_FROMDEVICE
+    DMA_FROM_DEVICE

@@
@@
-    PCI_DMA_NONE
+    DMA_NONE

@@
expression e1, e2, e3;
@@
-    pci_alloc_consistent(e1, e2, e3)
+    dma_alloc_coherent(&e1->dev, e2, e3, GFP_)

@@
expression e1, e2, e3;
@@
-    pci_zalloc_consistent(e1, e2, e3)
+    dma_alloc_coherent(&e1->dev, e2, e3, GFP_)

@@
expression e1, e2, e3, e4;
@@
-    pci_free_consistent(e1, e2, e3, e4)
+    dma_free_coherent(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_map_single(e1, e2, e3, e4)
+    dma_map_single(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_single(e1, e2, e3, e4)
+    dma_unmap_single(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4, e5;
@@
-    pci_map_page(e1, e2, e3, e4, e5)
+    dma_map_page(&e1->dev, e2, e3, e4, e5)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_page(e1, e2, e3, e4)
+    dma_unmap_page(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_map_sg(e1, e2, e3, e4)
+    dma_map_sg(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_sg(e1, e2, e3, e4)
+    dma_unmap_sg(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+    dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_single_for_device(e1, e2, e3, e4)
+    dma_sync_single_for_device(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+    dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+    dma_sync_sg_for_device(&e1->dev, e2, e3, e4)

@@
expression e1, e2;
@@
-    pci_dma_mapping_error(e1, e2)
+    dma_mapping_error(&e1->dev, e2)

@@
expression e1, e2;
@@
-    pci_set_dma_mask(e1, e2)
+    dma_set_mask(&e1->dev, e2)

@@
expression e1, e2;
@@
-    pci_set_consistent_dma_mask(e1, e2)
+    dma_set_coherent_mask(&e1->dev, e2)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

It's nice if the phy is online before we register the netdev
so try to do that first.

Stop trying to do "second tried" to register the phy, it
works perfectly fine the first time.

Stop remvoving the phy in uninit. Remove it when the
driver is remove():d, symmetric to where it is added, in
probe().
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This implements the missing MTU setting for the RTL8366RB
switch.

Apart from supporting jumboframes, this rids us of annoying
boot messages like this:
realtek-smi switch: nonfatal error -95 setting MTU on port 0
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

BLOCK_PRIV is never used after it was introduced.
So better to remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

DIGITAL_NFC_DEP_REQ_RES_TAILROOM is never used after it was introduced.
DIGITAL_NFC_DEP_REQ_RES_HEADROOM is no more used after below
commit e8e7f421 ("NFC: digital: Remove useless call to skb_reserve()")
Remove them.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Remove SRVL_CTRL_PKT_SIZE which is defined more than once.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Commit 0da4c3d3 ("net: phy: add Lynx PCS module") added the files in
./drivers/net/pcs/, but the new LYNX PCS MODULE section refers to
./drivers/net/phy/.

Hence, ./scripts/get_maintainer.pl --self-test=patterns complains:

  warning: no file matches    F:    drivers/net/phy/pcs-lynx.c

Repair the LYNX PCS MODULE section by referring to the right location.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Florian Fainelli says:

====================
net: dsa: bcm_sf2: Ensure MDIO diversion is used

Changes in v2:

- export of_update_property() to permit building bcm_sf2 as a module
- provided a better explanation of the problem being solved after
  explaining it to Andrew during the v1 review
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Registering our slave MDIO bus outside of the OF infrastructure is
necessary in order to avoid creating double references of the same
Device Tree nodes, however it is not sufficient to guarantee that the
MDIO bus diversion is used because of_phy_connect() will still resolve
to a valid PHY phandle and it will connect to the PHY using its parent
MDIO bus which is still the SF2 master MDIO bus. The reason for that is
because BCM7445 systems were already shipped with a Device Tree blob
looking like this (irrelevant parts omitted for simplicity):

	ports {
		#address-cells = <1>;
		#size-cells = <0>;

		port@1 {
			phy-mode = "rgmii-txid";
			phy-handle = <&phy0>;
                        reg = <1>;
			label = "rgmii_1";
		};
	...

	mdio@403c0 {
		...

		phy0: ethernet-phy@0 {
			broken-turn-around;
			device_type = "ethernet-phy";
			max-speed = <0x3e8>;
			reg = <0>;
			compatible = "brcm,bcm53125", "ethernet-phy-ieee802.3-c22";
		};
	};

There is a hardware issue with chip revisions (Dx) that lead to the
development of the following commits:

461cd1b0 ("net: dsa: bcm_sf2: Register our slave MDIO bus")
536fab5b ("net: dsa: bcm_sf2: Do not register slave MDIO bus with OF")
b8c6cd1d ("net: dsa: bcm_sf2: do not use indirect reads and writes for 7445E0")

There should have been an internal MDIO bus node created for the chip
revision (Dx) that suffers from this problem, but it did not happen back
then.

Had that happen, that we should have correctly parented phy@0 (bcm53125
below) as child node of the internal MDIO bus, but the production Device
Tree blob that was shipped with the firmware targeted the fixed version
of the chip, despite both the affected and corrected chips being shipped
into production.

The problem is that of_phy_connect() for port@1 will happily resolve the
'phy-handle' from the mdio@403c0 node, which bypasses the diversion
completely. This results in this double programming that the diversion
refers to and aims to avoid. In order to force of_phy_connect() to fail,
and have DSA call to dsa_slave_phy_connect(), we must deactivate
ethernet-phy@0 from mdio@403c0, and the best way to do that is by
removing the phandle property completely.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

We will need to remove some OF properties in drivers/net/dsa/bcm_sf2.c
with a subsequent commit. Export of_remove_property() to modules so we
can keep bcm_sf2 modular and provide an empty stub for when CONFIG_OF is
disabled to maintain the ability to compile test.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Edward Cree says:

====================
sfc: TXQ refactor

Refactor and unify partner-TXQ handling in the EF100 and legacy drivers.

The main thrust of this series is to remove from the legacy (Siena/EF10)
 driver the assumption that a netdev TX queue has precisely two hardware
 TXQs (checksummed and unchecksummed) associated with it, so that in
 future we can have more (e.g. for handling inner-header checksums) or
 fewer (e.g. to free up hardware queues for XDP usage).

Changes from v1:
 * better explain patch #1 in the commit message, and rename
   xmit_more_available to xmit_pending
 * add new patch #2 applying the same approach to ef100, for consistency
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

All users of this function are now gone.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Use efx_for_each_channel_tx_queue() rather than efx_tx_queue_partner().
Make some related simplifications of efx_nic_tx_is_empty() to remove
 entry points that aren't used.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Instead of open-coding the calculation with efx_tx_queue_partner(), use
 the functions that iterate over numbers of queues other than 2 with
 efx_for_each_channel_tx_queue().
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

As in the Siena/EF10 case, it minimises cacheline ping-pong between
 the TX and completion paths.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This should cause no functional change; merely make there only be one
 design of xmit_more handling to understand.  As with the EF10/Siena
 version, we set tx_queue->xmit_pending when we queue up a TX, and
 clear it when we ring the doorbell (in ef100_notify_tx_desc).
While we're at it, make ef100_notify_tx_desc static since nothing
 outside of ef100_tx.c uses it.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Instead of using efx_tx_queue_partner(), which relies on the assumption
 that tx_queues_per_channel is 2, efx_tx_send_pending() iterates over
 txqs with efx_for_each_channel_tx_queue().
We unconditionally set tx_queue->xmit_pending (renamed from
 xmit_more_available), then condition on xmit_more for the call to
 efx_tx_send_pending(), which will clear xmit_pending.  Thus, after an
 xmit_more TX, the doorbell is un-rung and xmit_pending is true.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.

Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe64 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pull s390 fixes from Vasily Gorbik:

 - Fix GENERIC_LOCKBREAK dependency on PREEMPTION in Kconfig broken
   because of a typo

 - Update defconfigs

* tag 's390-5.9-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390: update defconfigs
  s390: fix GENERIC_LOCKBREAK dependency typo in Kconfig

Pull arm64 fixes from Catalin Marinas:

 - Fix the loading of modules built with binutils-2.35. This version
   produces writable and executable .text.ftrace_trampoline section
   which is rejected by the kernel.

 - Remove the exporting of cpu_logical_map() as the Tegra driver has now
   been fixed and no longer uses this function.

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64/module: set trampoline section flags regardless of CONFIG_DYNAMIC_FTRACE
  arm64: Remove exporting cpu_logical_map symbol

Pull MIPS fixes from Thomas Bogendoerfer:
 "A few MIPS fixes:

   - fallthrough fallout fix

   - BMIPS fixes

   - MSA fix to avoid leaking MSA register contents

   - Loongson perf and cpu feature fix

   - SNI interrupt fix"

* tag 'mips_fixes_5.9_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
  MIPS: SNI: Fix SCSI interrupt
  MIPS: add missing MSACSR and upper MSA initialization
  MIPS: perf: Fix wrong check condition of Loongson event IDs
  mips/oprofile: Fix fallthrough placement
  MIPS: Loongson64: Remove unnecessary inclusion of boot_param.h
  MIPS: BMIPS: Also call bmips_cpu_setup() for secondary cores
  MIPS: mm: BMIPS5000 has inclusive physical caches
  MIPS: Loongson64: Do not override watch and ejtag feature

Merge tag 'kbuild-fixes-v5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - fix documents

 - fix warning in 'make localmodconfig'

* tag 'kbuild-fixes-v5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kconfig: remove redundant assignment prompt = prompt
  kbuild: Documentation: clean up makefiles.rst
  kconfig: streamline_config.pl: check defined(ENV variable) before using it
  Documentation/llvm: Improve formatting of commands, variables, and arguments

Pull power management fixes from Rafael Wysocki:
 "These fix reference counting in the operating performance points (OPP)
  framework and address a few intel_pstate driver issues, mostly related
  to switching driver operation modes and similar with hardware-managed
  P-states (HWP) enabled.

  Specifics:

   - Fix reference counting of operating performance points (OPP) tables
     (Viresh Kumar).

   - Address intel_pstate driver interface issues, mostly related to
     switching operation modes and handling CPU offline and online and
     system-wide suspend/resume with hardware-managed P-states (HWP)
     enabled (Rafael Wysocki).

   - Fix the maximum frequency computation in the intel_pstate driver
     with turbo P-states disabled by the platform firmware and HWP
     enabled (Francisco Jerez)"

* tag 'pm-5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: intel_pstate: Fix intel_pstate_get_hwp_max() for turbo disabled
  cpufreq: intel_pstate: Free memory only when turning off
  cpufreq: intel_pstate: Add ->offline and ->online callbacks
  cpufreq: intel_pstate: Tweak the EPP sysfs interface
  cpufreq: intel_pstate: Update cached EPP in the active mode
  cpufreq: intel_pstate: Refuse to turn off with HWP enabled
  opp: Don't drop reference for an OPP table that was never parsed

Pull libata fixes from Jens Axboe:

 - improve Sandisks ATA_HORKAGE on NCQ (Tejun)

 - link printk cleanup (Xu)

* tag 'libata-5.9-2020-09-04' of git://git.kernel.dk/linux-block:
  libata: implement ATA_HORKAGE_MAX_TRIM_128M and apply to Sandisks
  ata: ahci: use ata_link_info() instead of ata_link_printk()

Pull block fixes from Jens Axboe:
 "A bit larger than usual this week, mostly due to the NVMe fixes
  arriving late for -rc3 and hence didn't make last weeks pull request.

   - NVMe:
        - instance leak and io boundary fixes from Keith
        - fc locking fix from Christophe
        - various tcp/rdma reset during traffic fixes from Sagi
        - pci use-after-free fix from Tong
        - tcp target null deref fix from Ziye

   - Locking fix for partition removal (Christoph)

   - Ensure bdi->io_pages is always set (me)

   - Fixup for hd struct reference (Ming)

   - Fix for zero length bvecs (Ming)

   - Two small blk-iocost fixes (Tejun)"

* tag 'block-5.9-2020-09-04' of git://git.kernel.dk/linux-block:
  block: allow for_each_bvec to support zero len bvec
  blk-stat: make q->stats->lock irqsafe
  blk-iocost: ioc_pd_free() shouldn't assume irq disabled
  block: fix locking in bdev_del_partition
  block: release disk reference in hd_struct_free_work
  block: ensure bdi->io_pages is always initialized
  nvme-pci: cancel nvme device request before disabling
  nvme: only use power of two io boundaries
  nvme: fix controller instance leak
  nvmet-fc: Fix a missed _irqsave version of spin_lock in 'nvmet_fc_fod_op_done()'
  nvme: Fix NULL dereference for pci nvme controllers
  nvme-rdma: fix reset hang if controller died in the middle of a reset
  nvme-rdma: fix timeout handler
  nvme-rdma: serialize controller teardown sequences
  nvme-tcp: fix reset hang if controller died in the middle of a reset
  nvme-tcp: fix timeout handler
  nvme-tcp: serialize controller teardown sequences
  nvme: have nvme_wait_freeze_timeout return if it timed out
  nvme-fabrics: don't check state NVME_CTRL_NEW for request acceptance
  nvmet-tcp: Fix NULL dereference when a connect data comes in h2cdata pdu

Pull io_uring fixes from Jens Axboe:

 - EAGAIN with O_NONBLOCK retry fix

 - Two small fixes for registered files (Jiufei)

* tag 'io_uring-5.9-2020-09-04' of git://git.kernel.dk/linux-block:
  io_uring: no read/write-retry on -EAGAIN error and O_NONBLOCK marked file
  io_uring: set table->files[i] to NULL when io_sqe_file_register failed
  io_uring: fix removing the wrong file in __io_sqe_files_update()

Pull thermal fixes from Daniel Lezcano:

 - Fix bogus thermal shutdowns for omap4430 where bogus values resulting
   from an incorrect ADC conversion are too high and fire an emergency
   shutdown (Tony Lindgren)

 - Don't suppress negative temp for qcom spmi as they are valid and
   userspace needs them (Veera Vegivada)

 - Fix use-after-free in thermal_zone_device_unregister reported by
   Kasan (Dmitry Osipenko)

* tag 'thermal-v5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
  thermal: core: Fix use-after-free in thermal_zone_device_unregister()
  thermal: qcom-spmi-temp-alarm: Don't suppress negative temp
  thermal: ti-soc-thermal: Fix bogus thermal shutdowns for omap4430

Pull dmaengine fixes from Vinod Koul:
 "A couple of core fixes and odd driver fixes for dmaengine subsystem:

  Core:
   - drop ACPI CSRT table reference after using it
   - fix of_dma_router_xlate() error handling

  Drivers fixes in idxd, at_hdmac, pl330, dw-edma and jz478"

* tag 'dmaengine-fix-5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine:
  dmaengine: ti: k3-udma: Update rchan_oes_offset for am654 SYSFW ABI 3.0
  drivers/dma/dma-jz4780: Fix race condition between probe and irq handler
  dmaengine: dw-edma: Fix scatter-gather address calculation
  dmaengine: ti: k3-udma: Fix the TR initialization for prep_slave_sg
  dmaengine: pl330: Fix burst length if burst size is smaller than bus width
  dmaengine: at_hdmac: add missing kfree() call in at_dma_xlate()
  dmaengine: at_hdmac: add missing put_device() call in at_dma_xlate()
  dmaengine: at_hdmac: check return value of of_find_device_by_node() in at_dma_xlate()
  dmaengine: of-dma: Fix of_dma_router_xlate's of_dma_xlate handling
  dmaengine: idxd: reset states after device disable or reset
  dmaengine: acpi: Put the CSRT table after using it

Pull sound fixes from Takashi Iwai:
 "A collection of small changes, nothing intrusive:

   - remaining tasklet API conversions, now all sound stuff have been
     converted

   - a few HD-audio and USB-audio quirks and minor fixes

   - FireWire Tascam and Digi00xx fixes

   - drop a kernel WARNING from PCM OSS for syzkaller"

* tag 'sound-5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (29 commits)
  ALSA: hda/realtek - Improved routing for Thinkpad X1 7th/8th Gen
  ALSA: hda: use consistent HDAudio spelling in comments/docs
  ALSA: hda: add dev_dbg log when driver is not selected
  ALSA: hda: fix a runtime pm issue in SOF when integrated GPU is disabled
  ALSA: hda: hdmi - add Rocketlake support
  ALSA: ua101: convert tasklets to use new tasklet_setup() API
  ALSA: usb-audio: convert tasklets to use new tasklet_setup() API
  ASoC: txx9: convert tasklets to use new tasklet_setup() API
  ASoC: siu: convert tasklets to use new tasklet_setup() API
  ASoC: fsl_esai: convert tasklets to use new tasklet_setup() API
  ALSA: hdsp: convert tasklets to use new tasklet_setup() API
  ALSA: riptide: convert tasklets to use new tasklet_setup() API
  ALSA: pci/asihpi: convert tasklets to use new tasklet_setup() API
  ALSA: firewire: convert tasklets to use new tasklet_setup() API
  ALSA: core: convert tasklets to use new tasklet_setup() API
  ALSA: pcm: oss: Remove superfluous WARN_ON() for mulaw sanity check
  ALSA: hda - Fix silent audio output and corrupted input on MSI X570-A PRO
  ALSA: hda/hdmi: always check pin power status in i915 pin fixup
  ALSA: hda/realtek: Add quirk for Samsung Galaxy Book Ion NT950XCJ-X716A
  ALSA: usb-audio: Add basic capture support for Pioneer DJ DJM-250MK2
  ...