- 13 Jul, 2018 40 commits
-
-
Alex Deucher authored
use the structure member directly. Acked-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com>
-
Alex Deucher authored
use kaddr directly rather than secondary variable. Acked-by:
-
Alex Deucher authored
Rather than using the index variable stored in vram. If the device fails to come back online after a resume cycle, reads from vram will return all 1s which will cause a segfault. Based on a patch from Thomas Martitz <kugel@rockbox.org>. This avoids the segfault, but we still need to sort out why the GPU does not come back online after a resume. Bug: https://bugs.freedesktop.org/show_bug.cgi?id=105760Acked-by:
-
Alex Deucher authored
Use the PP_STATE_SUPPORT_* rather than AMD_CG_SUPPORT_* when communicating with the SMU. Reviewed-by:
Huang Rui <ray.huang@amd.com> Signed-off-by:
-
Dmytro Laktyushkin authored
[why] Currently we do not turn off autocal when scaling is in bypass. In case vbios enalbes auto scale and our first mode set is a non-scaled mode we have autocal on causing screen corruption. [how] moves turning autocal off to be first thing done during scaler setup Signed-off-by:
Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Reviewed-by:
Tony Cheng <Tony.Cheng@amd.com> Acked-by:
Harry Wentland <harry.wentland@amd.com> Signed-off-by:
-
Hugo Hu authored
[Why] Prevent unexpected color shows if DalMpVisualConfirm enable. [How] Zero out color configuration data for DalMpVisualConfirm when initiating. Signed-off-by:
Hugo Hu <hugo.hu@amd.com> Reviewed-by:
-
Tony Cheng authored
Signed-off-by:
Anthony Koo <Anthony.Koo@amd.com> Acked-by:
-
Dmytro Laktyushkin authored
DV updated their dml with an option to use max vstartup, this updates dc dml with the same option Signed-off-by:
-
Dmytro Laktyushkin authored
Signed-off-by:
Charlene Liu <Charlene.Liu@amd.com> Acked-by:
-
Ken Chalmers authored
[Why] The previous code could allow through attempts to enable more streams than there are timing generators, in designs where the number of pipes is greater than the number of timing generators. [How] Compare the new stream count to the resource pool's timing generator count, instead of its pipe count. Also correct a typo in the error message. Signed-off-by:
Ken Chalmers <ken.chalmers@amd.com> Reviewed-by:
-
Hersen Wu authored
[Why] when hw team does phy parameters tuning, there is need to force dp link rate or lane count grater than the values from dp receiver to check dp tx. current debufs limit link rate, lane count no more than rx caps. [How] remove force settings less than rx caps check v2: Fix typo in title Signed-off-by:
Hersen Wu <hersenxs.wu@amd.com> Reviewed-by:
-
David Francis authored
Signed-off-by:
David Francis <David.Francis@amd.com> Reviewed-by:
-
David Francis authored
[Why] Regamma/CTM tests require CRC support [How] The CRC registers that were used in DCE exist under different names in DCN. The code was copied from DCE (in dc/dce110/dce110_timing_generator.c) into DCN, and changed to use the DCN register access helper functions. Signed-off-by:
-
Fatemeh Darbehani authored
Signed-off-by:
Fatemeh Darbehani <fatemeh.darbehani@amd.com> Reviewed-by:
Aric Cyr <Aric.Cyr@amd.com> Acked-by:
-
Yue Hin Lau authored
[WHY] PNP cause bsod regression fix [HOW] Add NULL check Signed-off-by:
Yue Hin Lau <Yuehin.Lau@amd.com> Reviewed-by:
-
Mikita Lipski authored
[why] Add a switch statement to translate pp's powerlevel enum to dc powerlevel statement enum [how] Add a translator function Signed-off-by:
Mikita Lipski <mikita.lipski@amd.com> Reviewed-by:
Sun peng Li <Sunpeng.Li@amd.com> Acked-by:
-
Charlene Liu authored
[why] "DalEnableHDMI20" set to 0, disallow HDMI YCbCr420 and pixel clock > 340Mhz Default is enabled. Signed-off-by:
Jun Lei <Jun.Lei@amd.com> Acked-by:
-
Charlene Liu authored
Signed-off-by:
-
Leo (Sunpeng) Li authored
[Why] get_channel_status() can return 0 in returned_bytes, and report a successful operation result. This is because it prunes the first status byte out. This was preventing read_channel_reply() from being called (due to the faulty condition), and consequently preventing the AUX reply status from being set. [How] Fix the conditional so that it accounts for when get_channel_status() returns 0 bytes read. [Fixes] Fixes possible edid read failures during S3 resume, where we are now relying on DRM's DP AUX handling. This was an regression introduced by: Author: Harry Wentland <harry.wentland@amd.com> drm/amd/display: Return aux replies directly to DRM Signed-off-by: -
Leo (Sunpeng) Li authored
[Why] There is no point in keeping the AUX reply value in the raw format as returned from reading the AUX_SW_DATA register. [How] Shift it within read_channel_reply(), where the register is read, before returning it. Signed-off-by:
-
Eric Bernstein authored
v2: Remove spurious newline changes Signed-off-by:
Eric Bernstein <eric.bernstein@amd.com> Reviewed-by:
-
Jerry (Fangzhi) Zuo authored
[Why] Some monitors mark 4K@60 capable HDMI port only have 300MHz TMDS maximum, but the edid includes 4K@60 mode in cea extension block. [How] To enable 4K@60, need to limit BW by allowing YCbCr420 ONLY mode. Add YCbCr420 only support for monitors that do not fully support HDMI2.0, e.g., ASUS PA328. The YCbCr420 only support applies to DCN, DCE112 or higher. Signed-off-by:
Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com> Reviewed-by:
-
Tony Cheng authored
Signed-off-by:
-
Hersen Wu authored
bug fix: phy test PLTAT is special 80bit test pattern. The 80bit data should be hard coded within driver so that user does not need input the deata. previous driver does not have hard coded 80 bits pattern data for PLTPAT. Other than this PLTPAT, user has to input 80 bits pattern data. In case user input less than 10 bytes data, un-input data byte will be filled by 0x00. Signed-off-by:
-
Yongqiang Sun authored
Signed-off-by:
Yongqiang Sun <yongqiang.sun@amd.com> Reviewed-by:
-
Dmytro Laktyushkin authored
Signed-off-by:
-
Charlene Liu authored
Signed-off-by:
-
Charlene Liu authored
Signed-off-by:
Wesley Chalmers <Wesley.Chalmers@amd.com> Reviewed-by:
Duke Du <Duke.Du@amd.com> Acked-by:
-
Leo (Sunpeng) Li authored
GCC 4.9 reports a 'missing braces around initializer' error. This is a bug, documented here: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=53119 Fix it by adding another brace. Signed-off-by:
-
Hersen Wu authored
function: get current DP PHY settings: voltage swing, pre-emphasis, post-cursor2 (defined by VESA DP specification) valid values: voltage swing: 0,1,2,3 pre-emphasis : 0,1,2,3 post cursor2 : 0,1,2,3 debugfs file phy_setings is located at /sys/kernel/debug/dri/0/DP-x there will be directories, like DP-1, DP-2,DP-3, etc. for DP display --- to figure out which DP-x is the display for DP to be check, cd DP-x ls -ll There should be debugfs file, like link_settings, phy_settings. cat link_settings from lane_count, link_rate to figure which DP-x is for display to be worked on --- to get current DP PHY settings, cat phy_settings --- to change DP PHY settings, echo <voltage_swing> <pre-emphasis> <post_cursor2> > phy_settings for examle, to change voltage swing to 2, pre-emphasis to 3, post_cursor2 to 0, echo 2 3 0 > phy_settings --- to check if change be applied, get current phy settings by cat phy_settings --- in case invalid values are set by user, like echo 1 4 0 > phy_settings HW will NOT be programmed by these settings. cat phy_settings will show the previous valid settings. Signed-off-by:
-
Hugo Hu authored
[WHY] In eDP spec, the min duration in LCDVDD on-off-on sequence should be 500ms, some BOE panels need 700ms to pass. [HOW] Add patch to wait more time when eDP power on. Signed-off-by:
-
Dmytro Laktyushkin authored
Signed-off-by:
-
Dmytro Laktyushkin authored
Signed-off-by:
-
Dmytro Laktyushkin authored
Signed-off-by:
-
Hersen Wu authored
set PHY layer or Link layer test pattern PHY test pattern is used for PHY SI check. Link layer test will not affect PHY SI. - normal video mode 0 = DP_TEST_PATTERN_VIDEO_MODE - PHY test pattern supported 1 = DP_TEST_PATTERN_D102 2 = DP_TEST_PATTERN_SYMBOL_ERROR 3 = DP_TEST_PATTERN_PRBS7 4 = DP_TEST_PATTERN_80BIT_CUSTOM 5 = DP_TEST_PATTERN_CP2520_1 6 = DP_TEST_PATTERN_CP2520_2 = DP_TEST_PATTERN_HBR2_COMPLIANCE_EYE 7 = DP_TEST_PATTERN_CP2520_3 - DP PHY Link Training Patterns 8 = DP_TEST_PATTERN_TRAINING_PATTERN1 9 = DP_TEST_PATTERN_TRAINING_PATTERN2 0xa = DP_TEST_PATTERN_TRAINING_PATTERN3 0xb = DP_TEST_PATTERN_TRAINING_PATTERN4 - DP Link Layer Test pattern 0xc = DP_TEST_PATTERN_COLOR_SQUARES 0xd = DP_TEST_PATTERN_COLOR_SQUARES_CEA 0xe = DP_TEST_PATTERN_VERTICAL_BARS 0xf = DP_TEST_PATTERN_HORIZONTAL_BARS 0x10= DP_TEST_PATTERN_COLOR_RAMP debugfs phy_test_pattern is located at /syskernel/debug/dri/0/DP-x --- set test pattern echo <test pattern #> > test_pattern - custom test pattern If test pattern # is not supported, NO HW programming will be done for DP_TEST_PATTERN_80BIT_CUSTOM, it needs extra 10 bytes of data for the user pattern. input 10 bytes data are separated by space echo 0x4 0x11 0x22 0x33 0x44 0x55 0x66 0x77 0x88 0x99 0xaa > test_pattern --- reset test pattern echo 0 > test_pattern --- HPD detection is disabled when set PHY test pattern when PHY test pattern (pattern # within [1,7]) is set, HPD pin of HW ASIC is disable. User could unplug DP display from DP connected and plug scope to check test pattern PHY SI. If there is need unplug scope and plug DP display back, do steps below: echo 0 > phy_test_pattern unplug scope plug DP display. "echo 0 > phy_test_pattern" will re-enable HPD pin again so that video sw driver could detect "unplug scope" and "plug DP display" Signed-off-by:
-
Dmytro Laktyushkin authored
Signed-off-by:
-
Alvin lee authored
- define new dpcd address in drm - implement new members in dpcd_caps to store values read from new dpcd address Signed-off-by:
Alvin lee <alvin.lee3@amd.com> Reviewed-by:
-
Nicholas Kazlauskas authored
- Removed dal/dm/dc loggers from linux, switched to kernel prints - Modified functions that used these directly to use macros - dc_logger support is completely dropped from Linux Signed-off-by:
Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by:
-
Harry Wentland authored
Currently we still go through DC code that does error checking, retries, etc. There's no need for that since DRM already does that for us. This simplifies the code a bit and makes it easier to debug. This also ensures we correctly tell DRM how many bytes have actually been read, as we should. This allows DRM to correctly read the EDID on the Chamelium DP port. Signed-off-by:
-
Harry Wentland authored
DRM's DP helpers take care of dealing with the error code for us. In order not to step on each other's toes we'll need to be able to simply read auch channel replies without further logic based on return values. Signed-off-by:
-
