Skip to content

L
linux
Switch branch/tag
  1. 17 Aug, 2020 26 commits
  3. 15 Aug, 2020 4 commits
    • Wen Gong's avatar
      ath10k: correct the array index from mcs index for HT mode for QCA6174 · db04b755
      Wen Gong authored 
      The mcs index of HT mode is 0 to 31, please refer http://mcsindex.com/.
Its spatial stream(Nss) number is from 1 to 4, mcs index is 0~7 for
Nss=1, 8~15 for Nss=2, 16~23 for Nss=3 and 24~31 is for Nss=4.

The mcs is reported from firmware in wmi_tlv_peer_stats_info of
event WMI_TLV_PEER_STATS_INFO_EVENTID, its range is from 0~15 for
QCA6174 SDIO and PCIe. It is for both Nss=1 and Nss=2, and it has 2
rate table supported_ht_mcs_rate_nss1 and supported_ht_mcs_rate_nss2
in ath10k, they are for Nss=1 and Nss=2, each table has 8 rates.

It need to find the matched row number with the mcs index, for example,
mcs index is 2, it is <=7, so it is Nss=1, and match row 2 in table of
Nss=1. If mcs index is 12, it is >= 8 and <= 15, so it is Nss=2, it
match row 4(12-8) in table of Nss=2. If mcs index is >=16, it is for
Nss=3/4, it need to add rate table, so it is not support in current
ath10k.

This patch is to find the row number in rate table of Nss=1 or Nss=2
with the mcs index reported from firmware.

This patch only effect the chips which supports_peer_stats_info of its
hw_params is true, it is true only for QCA6174 currently.

Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00048
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Signed-off-by: default avatarWen Gong <wgong@codeaurora.org>
Signed-off-by: default avatarKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597392294-13124-1-git-send-email-wgong@codeaurora.org
      db04b755
    • Wen Gong's avatar
      ath10k: enable supports_peer_stats_info for QCA6174 PCI devices · cbcbabb9
      Wen Gong authored 
      When using QCA6174 PCI devices working in station mode, after connected
to AP, tx bitrate is always '1.0 MBit/s' in output of command 'iw wlan0
station dump'. (QCA6174 SDIO devices are working fine.)

After this patch, it show correct bitrate:

Station c4:04:15:5d:97:22 (on wls1)
        inactive time:  312 ms
        rx bytes:       31496
        rx packets:     173
        tx bytes:       8625
        tx packets:     46
        tx retries:     0
        tx failed:      0
        signal:         -76 [-88, -80] dBm
        signal avg:     -75 [-82, -77] dBm
        tx bitrate:     39.0 MBit/s MCS 4
        rx bitrate:     26.0 MBit/s MCS 3

Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Signed-off-by: default avatarWen Gong <wgong@codeaurora.org>
Signed-off-by: default avatarKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597312029-32348-4-git-send-email-wgong@codeaurora.org
      cbcbabb9
    • Wen Gong's avatar
      ath10k: remove return for NL80211_STA_INFO_TX_BITRATE · 1cd6ba8a
      Wen Gong authored 
      ath10k_sta_statistics is used to report many info to iw wlan0 link,
if it return for empty legacy and nss of arsta->txrate, then the other
stats after it will not be set.

It has 4 bit to set after the return:
NL80211_STA_INFO_TX_FAILED
NL80211_STA_INFO_RX_BITRATE
NL80211_STA_INFO_TX_BITRATE
NL80211_STA_INFO_TX_RETRIES

This patch not effect the info of above 4 bit for all hardware, reason
as below:

NL80211_STA_INFO_TX_FAILED is only for htt.disable_tx_comp is true, it
is for QCA6174 SDIO.

NL80211_STA_INFO_RX_BITRATE and NL80211_STA_INFO_TX_BITRATE are both
set in ath10k_mac_sta_get_peer_stats_info, it is only enabled for chips
which supports_peer_stats_info is true in hw_params, recently only for
QCA6174 SDIO, NL80211_STA_INFO_TX_BITRATE is set again in function
ath10k_mac_sta_get_peer_stats_info because the value which parsed from
arsta->tx_rate_code and arsta->tx_bitrate_kbps is correct for QCA6174
SDIO and PCIe, and the value arsta->txrate is not correct for QCA6174
SDIO and PCIe, so it need to set again with the correct value.

NL80211_STA_INFO_TX_RETRIES is use value of arsta->tx_retries, it is set
in ath10k_update_per_peer_tx_stats, which accumulate the retry_pkts in
HTT message from firmware, if the chips not support this feature, then
it is always 0 after accumulate, then iw wlan0 station dump always show
0 for retry count. If not set NL80211_STA_INFO_TX_RETRIES here, then it
is still 0, so the result is same, then set NL80211_STA_INFO_TX_RETRIES
has no effect.

Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00048
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Signed-off-by: default avatarWen Gong <wgong@codeaurora.org>
Signed-off-by: default avatarKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597312029-32348-3-git-send-email-wgong@codeaurora.org
      1cd6ba8a
    • Wen Gong's avatar
      ath10k: add wmi service peer stat info for wmi tlv · e39f32af
      Wen Gong authored 
      ath10k_sta_statistics is used to report info for iw wlan0 link,
it check ath10k_peer_stats_enabled, and ath10k_peer_stats_enabled
check WMI_SERVICE_PEER_STATS bit of ar->wmi.svc_map. SVCMAP() for
WMI_SERVICE_PEER_STATS was defined only for wmi_10x_svc_map and
wmi_10_4_svc_map interfaces, it missed in wmi_tlv_svc_map, so it is
not usable for iw wlan0 link for wmi tlv interface.

If firmware report WMI_TLV_SERVICE_PEER_STATS_INFO for wmi tlv, then
enable the WMI_SERVICE_PEER_STATS bit in ath10k, and then it pass check
in ath10k_peer_stats_enabled and ath10k_sta_statistics pass check.

Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00048
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Signed-off-by: default avatarWen Gong <wgong@codeaurora.org>
Signed-off-by: default avatarKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597312029-32348-2-git-send-email-wgong@codeaurora.org
      e39f32af
  5. 14 Aug, 2020 10 commits
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7